Provided by: libzmq3-dev_4.3.4-6_amd64 bug

NAME

       zmq_udp - 0MQ UDP multicast and unicast transport

SYNOPSIS

       UDP is unreliable protocol transport of data over IP networks. UDP support both unicast
       and multicast communication.

DESCRIPTION

       UDP transport can only be used with the ZMQ_RADIO and ZMQ_DISH socket types.

ADDRESSING

       A 0MQ endpoint is a string consisting of a transport:// followed by an address. The
       transport specifies the underlying protocol to use. The address specifies the
       transport-specific address to connect to.

       For the UDP transport, the transport is udp. The meaning of the address part is defined
       below.

       Binding a socket

           With 'udp' we can only bind the 'ZMQ_DISH' socket type.
           When binding a socket using _zmq_bind()_ with the 'udp'
           transport the 'endpoint' shall be interpreted as an 'interface' followed by a
           colon and the UDP port number to use.

           An 'interface' may be specified by either of the following:

           * The wild-card `*`, meaning all available interfaces.
           * The name of the network interface (i.e. eth0, lo, wlan0 etc...)
           * The primary address assigned to the interface, in its numeric representation.
           * Multicast address in its numeric representation the socket should join.

           The UDP port number may be specified a numeric value, usually above
           1024 on POSIX systems.

           Connecting a socket

       With udp we can only connect the ZMQ_RADIO socket type. When connecting a socket to a peer
       address using zmq_connect() with the udp transport, the endpoint shall be interpreted as a
       peer address followed by a colon and the UDP port number to use.

       A peer address may be specified by either of the following:

       •   The IPv4 or IPv6 address of the peer, in its numeric representation or using its
           hostname.

       •   Multicast address in its numeric representation.

EXAMPLES

       Binding a socket.

           //  Unicast - UDP port 5555 on all available interfaces
           rc = zmq_bind(dish, "udp://*:5555");
           assert (rc == 0);
           //  Unicast - UDP port 5555 on the local loop-back interface
           rc = zmq_bind(dish, "udp://127.0.0.1:5555");
           assert (rc == 0);
           //  Unicast - UDP port 5555 on interface eth1
           rc = zmq_bind(dish, "udp://eth1:5555");
           assert (rc == 0);
           //  Multicast - UDP port 5555 on a Multicast address
           rc = zmq_bind(dish, "udp://239.0.0.1:5555");
           assert (rc == 0);
           //  Same as above but joining only on interface eth0
           rc = zmq_bind(dish, "udp://eth0;239.0.0.1:5555");
           assert (rc == 0);
           //  Same as above using IPv6 multicast
           rc = zmq_bind(dish, "udp://eth0;[ff02::1]:5555");
           assert (rc == 0);

       Connecting a socket.

           //  Connecting using an Unicast IP address
           rc = zmq_connect(radio, "udp://192.168.1.1:5555");
           assert (rc == 0);
           //  Connecting using a Multicast address
           rc = zmq_connect(socket, "udp://239.0.0.1:5555);
           assert (rc == 0);
           //  Connecting using a Multicast address using local interface wlan0
           rc = zmq_connect(socket, "udp://wlan0;239.0.0.1:5555);
           assert (rc == 0);
           //  Connecting to IPv6 multicast
           rc = zmq_connect(socket, "udp://[ff02::1]:5555);
           assert (rc == 0);

SEE ALSO

       zmq_connect(3) zmq_setsockopt(3) zmq_tcp(7) zmq_ipc(7) zmq_inproc(7) zmq_vmci(7) zmq(7)

AUTHORS

       This page was written by the 0MQ community. To make a change please read the 0MQ
       Contribution Policy at http://www.zeromq.org/docs:contributing.