Provided by: flashrom_1.3.0-2ubuntu1_amd64 
NAME
flashrom - detect, read, write, verify and erase flash chips
SYNOPSIS
flashrom [-h|-R|-L|-z|
-p <programmername>[:<parameters>] [-c <chipname>]
(--flash-name|--flash-size|
[-E|-x|-r <file>|-w <file>|-v <file>]
[(-l <file>|--ifd| --fmap|--fmap-file <file>)
[-i <include>[:<file>]]]
[--wp-status] [--wp-list] [--wp-enable|--wp-disable]
[--wp-range <start>,<length>|--wp-region <region>]
[-n] [-N] [-f])]
[-V[V[V]]] [-o <logfile>]
DESCRIPTION
flashrom is a utility for detecting, reading, writing, verifying and erasing flash chips.
It's often used to flash BIOS/EFI/coreboot/firmware images in-system using a supported
mainboard. However, it also supports various external PCI/USB/parallel-port/serial-port
based devices which can program flash chips, including some network cards (NICs), SATA/IDE
controller cards, graphics cards, the Bus Pirate device, various FTDI
FT2232/FT4232H/FT232H based USB devices, and more.
It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, TSOP40, TSOP48, and
BGA chips, which use various protocols such as LPC, FWH, parallel flash, or SPI.
OPTIONS
You can specify one of -h, -R, -L, -z, -E, -r, -w, -v or no operation. If no operation is
specified, flashrom will only probe for flash chips. It is recommended that if you try
flashrom the first time on a system, you run it in probe-only mode and check the output.
Also you are advised to make a backup of your current ROM contents with -r before you try
to write a new image. All operations involving any chip access (probe/read/write/...)
require the -p/--programmer option to be used (please see below).
-r, --read <file>
Read flash ROM contents and save them into the given <file>. If the file already
exists, it will be overwritten.
-w, --write (<file>|-)
Write <file> into flash ROM. If - is provided instead, contents will be read from
stdin. This will first automatically
B erase the chip, then write to it.
In the process the chip is also read several times. First an in-memory backup is
made for disaster recovery and to be able to skip regions that are already equal to
the image file. This copy is updated along with the write operation. In case of
erase errors it is even re-read completely. After writing has finished and if
verification is enabled, the whole flash chip is read out and compared with the
input image.
-n, --noverify
Skip the automatic verification of flash ROM contents after writing. Using this
option is not recommended, you should only use it if you know what you are doing
and if you feel that the time for verification takes too long.
Typical usage is: flashrom -p prog -n -w <file>
This option is only useful in combination with --write.
-N, --noverify-all
Skip not included regions during automatic verification after writing (cf. -l and
-i). You should only use this option if you are sure that communication with the
flash chip is reliable (e.g. when using the internal programmer). Even if flashrom
is instructed not to touch parts of the flash chip, their contents could be damaged
(e.g. due to misunderstood erase commands).
This option is required to flash an Intel system with locked ME flash region using
the internal programmer. It may be enabled by default in this case in the future.
-v, --verify (<file>|-)
Verify the flash ROM contents against the given <file>. If - is provided instead,
contents will be written to the stdout.
-E, --erase
Erase the flash ROM chip.
-x, --extract
Extract every region defined on the layout from flash ROM chip to a file with the
same name as the extracted region (replacing spaces with underscores).
-V, --verbose
More verbose output. This option can be supplied multiple times (max. 3 times, i.e.
-VVV) for even more debug output.
-c, --chip <chipname>
Probe only for the specified flash ROM chip. This option takes the chip name as
printed by flashrom -L without the vendor name as parameter. Please note that the
chip name is case sensitive.
-f, --force
Force one or more of the following actions:
* Force chip read and pretend the chip is there.
* Force chip access even if the chip is bigger than the maximum supported size for
the flash bus.
* Force erase even if erase is known bad.
* Force write even if write is known bad.
-l, --layout <file>
Read ROM layout from <file>.
flashrom supports ROM layouts. This allows you to flash certain parts of the flash
chip only. A ROM layout file contains multiple lines with the following syntax:
startaddr:endaddr imagename
startaddr and endaddr are hexadecimal addresses within the ROM file and do not
refer to any physical address. Please note that using a 0x prefix for those
hexadecimal numbers is not necessary, but you can't specify decimal/octal numbers.
imagename is an arbitrary name for the region/image from startaddr to endaddr
(both addresses included).
Example:
00000000:00008fff gfxrom
00009000:0003ffff normal
00040000:0007ffff fallback
If you only want to update the image named normal in a ROM based on the layout
above, run
flashrom -p prog --layout rom.layout --image normal -w some.rom
To update only the images named normal and fallback, run:
flashrom -p prog -l rom.layout -i normal -i fallback -w some.rom
Overlapping sections are not supported.
--fmap Read layout from fmap in flash chip.
flashrom supports the fmap binary format which is commonly used by coreboot for
partitioning a flash chip. The on-chip fmap will be read and used to generate the
layout.
If you only want to update the COREBOOT region defined in the fmap, run
flashrom -p prog --fmap --image COREBOOT -w some.rom
--fmap-file <file>
Read layout from a <file> containing binary fmap (e.g. coreboot roms).
flashrom supports the fmap binary format which is commonly used by coreboot for
partitioning a flash chip. The fmap in the specified file will be read and used to
generate the layout.
If you only want to update the COREBOOT region defined in the binary fmap file, run
flashrom -p prog --fmap-file some.rom --image COREBOOT -w some.rom
--ifd Read ROM layout from Intel Firmware Descriptor.
flashrom supports ROM layouts given by an Intel Firmware Descriptor (IFD). The on-
chip descriptor will be read and used to generate the layout. If you need to change
the layout, you have to update the IFD only first.
The following ROM images may be present in an IFD:
fd the IFD itself
bios the host firmware aka. BIOS
me Intel Management Engine firmware
gbe gigabit ethernet firmware
pd platform specific data
-i, --include <region>[:<file>]
Read or write only <region> to or from ROM. The -i option may be used multiple
times if the user wishes to read or write multiple regions using a single command.
The user may optionally specify a corresponding <file> for any region they wish to
read or write. A read operation will read the corresponding regions from ROM and
write individual files for each one. A write option will read file(s) and write to
the corresponding region(s) in ROM.
For write operations, files specified using -i take precedence over content from
the argument to -w.
Examples:
To read regions named foo and bar in layout file <layout> into region-sized files
foo.bin and bar.bin, run:
flashrom -p prog -l <layout> -i foo:foo.bin -i bar:bar.bin -r rom.bin
To write files foo.bin and bar.bin into regions named foo and bar in layout file
<layout> to the ROM, run:
flashrom -p prog -l <layout> -i foo:foo.bin -i bar:bar.bin -w rom.bin
--wp-status
Prints the flash's current status register protection mode and write protection
range.
--wp-list
Prints a list of all protection ranges that the flash supports.
--wp-enable
Enables hardware status register protection (SRP) if the flash supports it. Once
SRP is enabled, operations that change the flash's status registers (including
--wp-disable and --wp-range) can only be performed if the flash's #WP pin is at an
inactive logic level.
--wp-disable
Disables status register protection if the flash allows it.
--wp-range <start>,<length>
Configures the flash to protect a range of addresses from <start> to (<start> +
<length> - 1), bounds inclusive. The range must be supported by the flash, see
--wp-list.
--wp-region <region>
Same as --wp-range but protects the range occupied by an image region. This option
requires a image layout to be specified, see --layout. The region must be supported
by the flash, see --wp-list.
--flash-name
Prints out the detected flash chip's name.
--flash-size
Prints out the detected flash chip's size.
--flash-contents <ref-file>
The file contents of <ref-file> will be used to decide which parts of the flash
need to be written. Providing this saves an initial read of the full flash chip. Be
careful, if the provided data doesn't actually match the flash contents, results
are undefined.
-L, --list-supported
List the flash chips, chipsets, mainboards, and external programmers (including
PCI, USB, parallel port, and serial port based devices) supported by flashrom.
There are many unlisted boards which will work out of the box, without special
support in flashrom. Please let us know if you can verify that other boards work or
do not work out of the box.
IMPORTANT: For verification you have to test an ERASE and/or WRITE operation, so
make sure you only do that if you have proper means to recover from failure!
-z, --list-supported-wiki
Same as --list-supported, but outputs the supported hardware in MediaWiki syntax,
so that it can be easily pasted into the supported hardware wiki page
⟨https://flashrom.org/Supported_hardware⟩. Please note that MediaWiki output is
not compiled in by default.
-p, --programmer <name>[:parameter[,parameter[,parameter]]]
Specify the programmer device. This is mandatory for all operations involving any
chip access (probe/read/write/...). Currently supported are:
* internal (for in-system flashing in the mainboard)
* dummy (virtual programmer for testing flashrom)
* nic3com (for flash ROMs on 3COM network cards)
* nicrealtek (for flash ROMs on Realtek and SMC 1211 network cards)
* nicnatsemi (for flash ROMs on National Semiconductor DP838* network cards)
* nicintel (for parallel flash ROMs on Intel 10/100Mbit network cards)
* gfxnvidia (for flash ROMs on NVIDIA graphics cards)
* drkaiser (for flash ROMs on Dr. Kaiser PC-Waechter PCI cards)
* satasii (for flash ROMs on Silicon Image SATA/IDE controllers)
* satamv (for flash ROMs on Marvell SATA controllers)
* atahpt (for flash ROMs on Highpoint ATA/RAID controllers)
* atavia (for flash ROMs on VIA VT6421A SATA controllers)
* atapromise (for flash ROMs on Promise PDC2026x ATA/RAID controllers)
* it8212 (for flash ROMs on ITE IT8212F ATA/RAID controller)
* ft2232_spi (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family based
USB SPI programmer).
* serprog (for flash ROMs attached to a programmer speaking serprog, including some
Arduino-based devices).
* buspirate_spi (for SPI flash ROMs attached to a Bus Pirate)
* dediprog (for SPI flash ROMs attached to a Dediprog SF100)
* rayer_spi (for SPI flash ROMs attached to a parallel port by one of various cable
types)
* raiden_debug_spi (For Chrome EC based debug tools - SuzyQable, Servo V4, C2D2 &
uServo)
* pony_spi (for SPI flash ROMs attached to a SI-Prog serial port bitbanging
adapter)
* nicintel_spi (for SPI flash ROMs on Intel Gigabit network cards)
* ogp_spi (for SPI flash ROMs on Open Graphics Project graphics card)
* linux_mtd (for SPI flash ROMs accessible via /dev/mtdX on Linux)
* linux_spi (for SPI flash ROMs accessible via /dev/spidevX.Y on Linux)
* usbblaster_spi (for SPI flash ROMs attached to an Altera USB-Blaster compatible
cable)
* nicintel_eeprom (for SPI EEPROMs on Intel Gigabit network cards)
* mstarddc_spi (for SPI flash ROMs accessible through DDC in MSTAR-equipped
displays)
* pickit2_spi (for SPI flash ROMs accessible via Microchip PICkit2)
* ch341a_spi (for SPI flash ROMs attached to WCH CH341A)
* digilent_spi (for SPI flash ROMs attached to iCEblink40 development boards)
* jlink_spi (for SPI flash ROMs attached to SEGGER J-Link and compatible devices)
* ni845x_spi (for SPI flash ROMs attached to National Instruments USB-8451 or
USB-8452)
* stlinkv3_spi (for SPI flash ROMs attached to STMicroelectronics STLINK V3
devices)
* realtek_mst_i2c_spi (for SPI flash ROMs attached to Realtek DisplayPort hubs
accessible through I2C)
* parade_lspcon (for SPI flash ROMs attached to Parade Technologies LSPCONs
(PS175))
* mediatek_i2c_spi (for SPI flash ROMs attached to some Mediatek display devices
accessible over I2C)
* dirtyjtag_spi (for SPI flash ROMs attached to DirtyJTAG-compatible devices)
Some programmers have optional or mandatory parameters which are described in
detail in the PROGRAMMER-SPECIFIC INFORMATION section. Support for some programmers
can be disabled at compile time. flashrom -h lists all supported programmers.
-h, --help
Show a help text and exit.
-o, --output <logfile>
Save the full debug log to <logfile>. If the file already exists, it will be
overwritten. This is the recommended way to gather logs from flashrom because they
will be verbose even if the on-screen messages are not verbose and don't require
output redirection.
-R, --version
Show version information and exit.
PROGRAMMER-SPECIFIC INFORMATION
Some programmer drivers accept further parameters to set programmer-specific parameters.
These parameters are separated from the programmer name by a colon. While some programmers
take arguments at fixed positions, other programmers use a key/value interface in which
the key and value is separated by an equal sign and different pairs are separated by a
comma or a colon.
internal programmer
Board Enables
Some mainboards require to run mainboard specific code to enable flash erase and
write support (and probe support on old systems with parallel flash). The
mainboard brand and model (if it requires specific code) is usually autodetected
using one of the following mechanisms: If your system is running coreboot, the
mainboard type is determined from the coreboot table. Otherwise, the mainboard is
detected by examining the onboard PCI devices and possibly DMI info. If PCI and DMI
do not contain information to uniquely identify the mainboard (which is the
exception), or if you want to override the detected mainboard model, you can
specify the mainboard using the
flashrom -p internal:mainboard=<vendor>:<board> syntax.
See the 'Known boards' or 'Known laptops' section in the output of 'flashrom -L'
for a list of boards which require the specification of the board name, if no
coreboot table is found.
Some of these board-specific flash enabling functions (called board enables) in
flashrom have not yet been tested. If your mainboard is detected needing an
untested board enable function, a warning message is printed and the board enable
is not executed, because a wrong board enable function might cause the system to
behave erratically, as board enable functions touch the low-level internals of a
mainboard. Not executing a board enable function (if one is needed) might cause
detection or erasing failure. If your board protects only part of the flash
(commonly the top end, called boot block), flashrom might encounter an error only
after erasing the unprotected part, so running without the board-enable function
might be dangerous for erase and write (which includes erase).
The suggested procedure for a mainboard with untested board specific code is to
first try to probe the ROM (just invoke flashrom and check that it detects your
flash chip type) without running the board enable code (i.e. without any
parameters). If it finds your chip, fine. Otherwise, retry probing your chip with
the board-enable code running, using
flashrom -p internal:boardenable=force
If your chip is still not detected, the board enable code seems to be broken or the
flash chip unsupported. Otherwise, make a backup of your current ROM contents
(using -r) and store it to a medium outside of your computer, like a USB drive or a
network share. If you needed to run the board enable code already for probing, use
it for reading too. If reading succeeds and the contents of the read file look
legit you can try to write the new image. You should enable the board enable code
in any case now, as it has been written because it is known that writing/erasing
without the board enable is going to fail. In any case (success or failure), please
report to the flashrom mailing list, see below.
Coreboot
On systems running coreboot, flashrom checks whether the desired image matches your
mainboard. This needs some special board ID to be present in the image. If
flashrom detects that the image you want to write and the current board do not
match, it will refuse to write the image unless you specify
flashrom -p internal:boardmismatch=force
ITE IT87 Super I/O
If your mainboard is manufactured by GIGABYTE and supports DualBIOS it is very
likely that it uses an ITE IT87 series Super I/O to switch between the two flash
chips. Only one of them can be accessed at a time and you can manually select which
one to use with the
flashrom -p internal:dualbiosindex=chip
syntax where chip is the index of the chip to use (0 = main, 1 = backup). You can
check which one is currently selected by leaving out the chip parameter.
If your mainboard uses an ITE IT87 series Super I/O for LPC<->SPI flash bus
translation, flashrom should autodetect that configuration. If you want to set the
I/O base port of the IT87 series SPI controller manually instead of using the value
provided by the BIOS, use the
flashrom -p internal:it87spiport=portnum
syntax where portnum is the I/O port number (must be a multiple of 8). In the
unlikely case flashrom doesn't detect an active IT87 LPC<->SPI bridge, please send
a bug report so we can diagnose the problem.
AMD chipsets
Beginning with the SB700 chipset there is an integrated microcontroller (IMC) based
on the 8051 embedded in every AMD southbridge. Its firmware resides in the same
flash chip as the host's which makes writing to the flash risky if the IMC is
active. Flashrom tries to temporarily disable the IMC but even then changing the
contents of the flash can have unwanted effects: when the IMC continues (at the
latest after a reboot) it will continue executing code from the flash. If the code
was removed or changed in an unfortunate way it is unpredictable what the IMC will
do. Therefore, if flashrom detects an active IMC it will disable write support
unless the user forces it with the
flashrom -p internal:amd_imc_force=yes
syntax. The user is responsible for supplying a suitable image or leaving out the
IMC region with the help of a layout file. This limitation might be removed in the
future when we understand the details better and have received enough feedback from
users. Please report the outcome if you had to use this option to write a chip.
An optional spispeed parameter specifies the frequency of the SPI bus where
applicable (i.e. SB600 or later with an SPI flash chip directly attached to the
chipset). Syntax is
flashrom -p internal:spispeed=frequency
where frequency can be '16.5 MHz', '22 MHz', '33 MHz', '66 MHz', '100 MHZ', or
'800 kHz'. Support of individual frequencies depends on the generation of the
chipset:
* SB6xx, SB7xx, SP5xxx: from 16.5 MHz up to and including 33 MHz
-The default is to use 16.5 MHz and disable Fast Reads.
* SB8xx, SB9xx, Hudson: from 16.5 MHz up to and including 66 MHz
-The default is to use 16.5 MHz and disable Fast Reads.
* Yangtze (with SPI 100 engine as found in Kabini and Tamesh): all of them
-The default is to use the frequency that is currently configured.
An optional spireadmode parameter specifies the read mode of the SPI bus where
applicable (Bolton or later). Syntax is
flashrom -p internal:spireadmode=mode
where mode can be 'Normal (up to 33 MHz)', 'Normal (up to 66 MHz)',
'Dual IO (1-1-2)', 'Quad IO (1-1-4)', 'Dual IO (1-2-2)', 'Quad IO (1-4-4)', or
'Fast Read'.
The default is to use the read mode that is currently configured.
Intel chipsets
If you have an Intel chipset with an ICH8 or later southbridge with SPI flash
attached, and if a valid descriptor was written to it (e.g. by the vendor), the
chipset provides an alternative way to access the flash chip(s) named Hardware
Sequencing. It is much simpler than the normal access method (called Software
Sequencing), but does not allow the software to choose the SPI commands to be sent.
You can use the
flashrom -p internal:ich_spi_mode=value
syntax where value can be auto, swseq or hwseq. By default (or when setting
ich_spi_mode=auto) the module tries to use swseq and only activates hwseq if need
be (e.g. if important opcodes are inaccessible due to lockdown; or if more than one
flash chip is attached). The other options (swseq, hwseq) select the respective
mode (if possible).
ICH8 and later southbridges may also have locked address ranges of different kinds
if a valid descriptor was written to it. The flash address space is then
partitioned in multiple so called "Flash Regions" containing the host firmware, the
ME firmware and so on respectively. The flash descriptor can also specify up to 5
so called "Protected Regions", which are freely chosen address ranges independent
from the aforementioned "Flash Regions". All of them can be write and/or read
protected individually.
If you have an Intel chipset with an ICH2 or later southbridge and if you want to
set specific IDSEL values for a non-default flash chip or an embedded controller
(EC), you can use the
flashrom -p internal:fwh_idsel=value
syntax where value is the 48-bit hexadecimal raw value to be written in the IDSEL
registers of the Intel southbridge. The upper 32 bits use one hex digit each per
512 kB range between 0xffc00000 and 0xffffffff, and the lower 16 bits use one hex
digit each per 1024 kB range between 0xff400000 and 0xff7fffff. The rightmost hex
digit corresponds with the lowest address range. All address ranges have a
corresponding sister range 4 MB below with identical IDSEL settings. The default
value for ICH7 is given in the example below.
Example: flashrom -p internal:fwh_idsel=0x001122334567
Laptops
Using flashrom on older laptops that don't boot from the SPI bus is dangerous and
may easily make your hardware unusable (see also the BUGS section). The embedded
controller (EC) in some machines may interact badly with flashing. More
information is in the wiki ⟨https://flashrom.org/Laptops⟩. Problems occur when the
flash chip is shared between BIOS and EC firmware, and the latter does not expect
flashrom to access the chip. While flashrom tries to change the contents of that
memory the EC might need to fetch new instructions or data from it and could stop
working correctly. Probing for and reading from the chip may also irritate your EC
and cause fan failure, backlight failure, sudden poweroff, and other nasty effects.
flashrom will attempt to detect if it is running on such a laptop and limit probing
to SPI buses. If you want to probe the LPC bus anyway at your own risk, use
flashrom -p internal:laptop=force_I_want_a_brick
We will not help you if you force flashing on a laptop because this is a really
dumb idea.
You have been warned.
Currently we rely on the chassis type encoded in the DMI/SMBIOS data to detect
laptops. Some vendors did not implement those bits correctly or set them to generic
and/or dummy values. flashrom will then issue a warning and restrict buses like
above. In this case you can use
flashrom -p internal:laptop=this_is_not_a_laptop
to tell flashrom (at your own risk) that it is not running on a laptop.
dummy programmer
The dummy programmer operates on a buffer in memory only. It provides a safe and
fast way to test various aspects of flashrom and is mainly used in development and
while debugging. It is able to emulate some chips to a certain degree (basic
identify/read/erase/write operations work).
An optional parameter specifies the bus types it should support. For that you have
to use the
flashrom -p dummy:bus=[type[+type[+type]]]
syntax where type can be parallel, lpc, fwh, spi in any order. If you specify bus
without type, all buses will be disabled. If you do not specify bus, all buses
will be enabled.
Example: flashrom -p dummy:bus=lpc+fwh
The dummy programmer supports flash chip emulation for automated self-tests without
hardware access. If you want to emulate a flash chip, use the
flashrom -p dummy:emulate=chip
syntax where chip is one of the following chips (please specify only the chip name,
not the vendor):
* ST M25P10.RES SPI flash chip (128 kB, RES, page write)
* SST SST25VF040.REMS SPI flash chip (512 kB, REMS, byte write)
* SST SST25VF032B SPI flash chip (4096 kB, RDID, AAI write)
* Macronix MX25L6436 SPI flash chip (8192 kB, RDID, SFDP)
* Winbond W25Q128FV SPI flash chip (16384 kB, RDID)
* Spansion S25FL128L SPI flash chip (16384 kB, RDID)
* Dummy vendor VARIABLE_SIZE SPI flash chip (configurable size, page write)
Example: flashrom -p dummy:emulate=SST25VF040.REMS
To use VARIABLE_SIZE chip, size must be specified to configure the size of the
flash chip as a power of two.
Example: flashrom -p dummy:emulate=VARIABLE_SIZE,size=16777216,image=dummy.bin
Persistent images
If you use flash chip emulation, flash image persistence is available as well by
using the
flashrom -p dummy:emulate=chip,image=image.rom
syntax where image.rom is the file where the simulated chip contents are read on
flashrom startup and where the chip contents on flashrom shutdown are written to.
Example: flashrom -p dummy:emulate=M25P10.RES,image=dummy.bin
SPI write chunk size
If you use SPI flash chip emulation for a chip which supports SPI page write with
the default opcode, you can set the maximum allowed write chunk size with the
flashrom -p dummy:emulate=chip,spi_write_256_chunksize=size
syntax where size is the number of bytes (min. 1, max. 256).
Example:
flashrom -p dummy:emulate=M25P10.RES,spi_write_256_chunksize=5
SPI blacklist
To simulate a programmer which refuses to send certain SPI commands to the flash
chip, you can specify a blacklist of SPI commands with the
flashrom -p dummy:spi_blacklist=commandlist
syntax where commandlist is a list of two-digit hexadecimal representations of SPI
commands. If commandlist is e.g. 0302, flashrom will behave as if the SPI
controller refuses to run command 0x03 (READ) and command 0x02 (WRITE).
commandlist may be up to 512 characters (256 commands) long. Implementation note:
flashrom will detect an error during command execution.
SPI ignorelist
To simulate a flash chip which ignores (doesn't support) certain SPI commands, you
can specify an ignorelist of SPI commands with the
flashrom -p dummy:spi_ignorelist=commandlist
syntax where commandlist is a list of two-digit hexadecimal representations of SPI
commands. If commandlist is e.g. 0302, the emulated flash chip will ignore command
0x03 (READ) and command 0x02 (WRITE). commandlist may be up to 512 characters (256
commands) long. Implementation note: flashrom won't detect an error during command
execution.
SPI status register
You can specify the initial content of the chip's status register with the
flashrom -p dummy:spi_status=content
syntax where content is a hexadecimal value of up to 24 bits. For example, 0x332211
assigns 0x11 to SR1, 0x22 to SR2 and 0x33 to SR3. Shorter value is padded to 24
bits with zeroes on the left. See datasheet for chosen chip for details about the
registers content.
Write protection
Chips with emulated WP: W25Q128FV, S25FL128L.
You can simulate state of hardware protection pin (WP) with the
flashrom -p dummy:hwwp=state
syntax where state is "yes" or "no" (default value). "yes" means active state of
the pin implies that chip is write-protected (on real hardware the pin is usually
negated, but not here).
nic3com, nicrealtek, nicnatsemi, nicintel, nicintel_eeprom, nicintel_spi, gfxnvidia, ogp_spi,
drkaiser, satasii, satamv, atahpt, atavia , atapromise and it8212 programmers
These programmers have an option to specify the PCI address of the card your want
to use, which must be specified if more than one card supported by the selected
programmer is installed in your system. The syntax is
flashrom -p xxxx:pci=bb:dd.f,
where xxxx is the name of the programmer, bb is the PCI bus number, dd is the PCI
device number, and f is the PCI function number of the desired device.
Example: flashrom -p nic3com:pci=05:04.0
atavia programmer
Due to the mysterious address handling of the VIA VT6421A controller the user can
specify an offset with the
flashrom -p atavia:offset=addr
syntax where addr will be interpreted as usual (leading 0x (0) for hexadecimal
(octal) values, or else decimal). For more information please see its wiki page
⟨https://flashrom.org/VT6421A⟩.
atapromise programmer
This programmer is currently limited to 32 kB, regardless of the actual size of the
flash chip. This stems from the fact that, on the tested device (a Promise
Ultra100), not all of the chip's address lines were actually connected. You may use
this programmer to flash firmware updates, since these are only 16 kB in size
(padding to 32 kB is required).
nicintel_eeprom programmer
This is the first programmer module in flashrom that does not provide access to NOR
flash chips but EEPROMs mounted on gigabit Ethernet cards based on Intel's 82580
NIC. Because EEPROMs normally do not announce their size nor allow themselves to be
identified, the controller relies on correct size values written to predefined
addresses within the chip. Flashrom follows this scheme but assumes the minimum
size of 16 kB (128 kb) if an unprogrammed EEPROM/card is detected. Intel specifies
following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST) M95128,
M95256 and OnSemi (Catalyst) CAT25CS128.
ft2232_spi programmer
This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips
including the DLP Design DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-
tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, Olimex ARM-USB-TINY/-H, Olimex
ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB Multi-
Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP, Google Servo v1/v2, Tin Can
Tools Flyswatter/Flyswatter 2 and Kristech KT-LINK.
An optional parameter specifies the controller type, channel/interface/port it
should support. For that you have to use the
flashrom -p ft2232_spi:type=model,port=interface
syntax where model can be 2232H, 4232H, 232H, jtagkey, busblaster, openmoko, arm-
usb-tiny, arm-usb-tiny-h, arm-usb-ocd, arm-usb-ocd-h, tumpa, tumpalite, picotap,
google-servo, google-servo-v2, google-servo-v2-legacy or kt-link interface can be
A, B, C, or D. The default model is 4232H the default interface is A and GPIO is
not used by default.
If there is more than one ft2232_spi-compatible device connected, you can select
which one should be used by specifying its serial number with the
flashrom -p ft2232_spi:serial=number
syntax where number is the serial number of the device (which can be found for
example in the output of lsusb -v).
All models supported by the ft2232_spi driver can configure the SPI clock rate by
setting a divisor. The expressible divisors are all even numbers between 2 and 2^17
(=131072) resulting in SPI clock frequencies of 6 MHz down to about 92 Hz for 12
MHz inputs. The default divisor is set to 2, but you can use another one by
specifying the optional divisor parameter with the
flashrom -p ft2232_spi:divisor=div
syntax.
Using the parameter csgpiol (DEPRECATED - use gpiol instead) an additional CS# pin
can be chosen, where the value can be a number between 0 and 3, denoting
GPIOL0-GPIOL3 correspondingly. Example:
flashrom -p ft2232_spi:csgpiol=3
The parameter gpiolX=[HLC] allows use of the GPIOL pins either as generic gpios
with a fixed value during flashing or as additional CS# signal, where X can be a
number between 0 and 3, denoting GPIOL0-GPIOL3 correspondingly. The parameter may
be specified multiple times, one time per GPIOL pin. Valid values are H , L and C
:
H - Set GPIOL output high
L - Set GPIOL output low
C - Use GPIOL as additional CS# output
Example:
flashrom -p ft2232_spi:gpiol0=H
Note that not all GPIOL pins are freely usable with all programmers as some have
special functionality.
serprog programmer
This module supports all programmers speaking the serprog protocol. This includes
some Arduino-based devices as well as various programmers by Urja Rannikko, Juhana
Helovuo, Stefan Tauner, Chi Zhang and many others.
A mandatory parameter specifies either a serial device (and baud rate) or an
IP/port combination for communicating with the programmer. The device/baud
combination has to start with dev= and separate the optional baud rate with a
colon. For example
flashrom -p serprog:dev=/dev/ttyS0:115200
If no baud rate is given the default values by the operating system/hardware will
be used. For IP connections you have to use the
flashrom -p serprog:ip=ipaddr:port
syntax. In case the device supports it, you can set the SPI clock frequency with
the optional spispeed parameter. The frequency is parsed as hertz, unless an M, or
k suffix is given, then megahertz or kilohertz are used respectively. Example that
sets the frequency to 2 MHz:
flashrom -p serprog:dev=/dev/device:baud,spispeed=2M
More information about serprog is available in serprog-protocol.txt in the source
distribution.
buspirate_spi programmer
A required dev parameter specifies the Bus Pirate device node and an optional
spispeed parameter specifies the frequency of the SPI bus. The parameter delimiter
is a comma. Syntax is
flashrom -p buspirate_spi:dev=/dev/device,spispeed=frequency
where frequency can be 30k, 125k, 250k, 1M, 2M, 2.6M, 4M or 8M (in Hz). The default
is the maximum frequency of 8 MHz.
The baud rate for communication between the host and the Bus Pirate can be
specified with the optional serialspeed parameter. Syntax is
flashrom -p buspirate_spi:serialspeed=baud
where baud can be 115200, 230400, 250000 or 2000000 (2M). The default is 2M baud
for Bus Pirate hardware version 3.0 and greater, and 115200 otherwise.
An optional pullups parameter specifies the use of the Bus Pirate internal pull-up
resistors. This may be needed if you are working with a flash ROM chip that you
have physically removed from the board. Syntax is
flashrom -p buspirate_spi:pullups=state
where state can be on or off. More information about the Bus Pirate pull-up
resistors and their purpose is available in a guide by dangerousprototypes
⟨http://dangerousprototypes.com/docs/Practical_guide_to_Bus_Pirate_pull-
up_resistors⟩.
The state of the Bus Pirate power supply pins is controllable through an optional
psus parameter. Syntax is
flashrom -p buspirate_spi:psus=state
where state can be on or off. This allows the bus pirate to power the ROM chip
directly. This may also be used to provide the required pullup voltage (when using
the pullups option), by connecting the Bus Pirate's Vpu input to the appropriate
Vcc pin.
pickit2_spi programmer
An optional voltage parameter specifies the voltage the PICkit2 should use. The
default unit is Volt if no unit is specified. You can use mV, millivolt, V or Volt
as unit specifier. Syntax is
flashrom -p pickit2_spi:voltage=value
where value can be 0V, 1.8V, 2.5V, 3.5V or the equivalent in mV.
An optional spispeed parameter specifies the frequency of the SPI bus. Syntax is
flashrom -p pickit2_spi:spispeed=frequency
where frequency can be 250k, 333k, 500k or 1M (in Hz). The default is a frequency
of 1 MHz.
dediprog programmer
An optional voltage parameter specifies the voltage the Dediprog should use. The
default unit is Volt if no unit is specified. You can use mV, milliVolt, V or Volt
as unit specifier. Syntax is
flashrom -p dediprog:voltage=value
where value can be 0V, 1.8V, 2.5V, 3.5V or the equivalent in mV.
An optional device parameter specifies which of multiple connected Dediprog devices
should be used. Please be aware that the order depends on libusb's
usb_get_busses() function and that the numbering starts at 0. Usage example to
select the second device:
flashrom -p dediprog:device=1
An optional spispeed parameter specifies the frequency of the SPI bus. The firmware
on the device needs to be 5.0.0 or newer. Syntax is
flashrom -p dediprog:spispeed=frequency
where frequency can be 375k, 750k, 1.5M, 2.18M, 3M, 8M, 12M or 24M (in Hz). The
default is a frequency of 12 MHz.
An optional target parameter specifies which target chip should be used. Syntax is
flashrom -p dediprog:target=value
where value can be 1 or 2 to select target chip 1 or 2 respectively. The default is
target chip 1.
rayer_spi programmer
The default I/O base address used for the parallel port is 0x378 and you can use
the optional iobase parameter to specify an alternate base I/O address with the
flashrom -p rayer_spi:iobase=baseaddr
syntax where baseaddr is base I/O port address of the parallel port, which must be
a multiple of four. Make sure to not forget the "0x" prefix for hexadecimal port
addresses.
The default cable type is the RayeR cable. You can use the optional type parameter
to specify the cable type with the
flashrom -p rayer_spi:type=model
syntax where model can be rayer for the RayeR cable, byteblastermv for the Altera
ByteBlasterMV, stk200 for the Atmel STK200/300, wiggler for the Macraigor Wiggler,
xilinx for the Xilinx Parallel Cable III (DLC 5), or spi_tt for SPI Tiny Tools-
compatible hardware.
More information about the RayeR hardware is available at RayeR's website
⟨http://rayer.g6.cz/elektro/spipgm.htm⟩. The Altera ByteBlasterMV datasheet can be
obtained from Altera ⟨http://www.altera.co.jp/literature/ds/dsbytemv.pdf⟩. For
more information about the Macraigor Wiggler see their company homepage
⟨http://www.macraigor.com/wiggler.htm⟩. The schematic of the Xilinx DLC 5 was
published in a Xilinx user guide
⟨http://www.xilinx.com/support/documentation/user_guides/xtp029.pdf⟩.
raiden_debug_spi programmer
The target of the SPI flashing mux must be specified with the target parameter with
the
flashrom -p raiden_debug_spi:target=chip
syntax, where chip is either the ap or ec to flash, otherwise a unspecified target
terminates at the end-point.
The default is to use the first available servo. You can use the optional serial
parameter to specify the servo USB device serial number to use specifically with
flashrom -p raiden_debug_spi:serial=XXX
The servo device serial number can be found via lsusb.
Raiden will poll the ap target waiting for the system power to settle on the AP and
EC flash devices.
The optional custom_rst=true parameter changes the timeout value from 3ms to 10ms.
flashrom -p raiden_debug_spi:custom_rst=<true|false>
syntax, where custom_rst=false is the implicit default timeout of 3ms.
More information about the ChromiumOS servo hardware is available at servo website
⟨https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/HEAD/docs/servo_v4.md⟩.
pony_spi programmer
The serial port (like /dev/ttyS0, /dev/ttyUSB0 on Linux or COM3 on windows) is
specified using the mandatory dev parameter. The adapter type is selectable between
SI-Prog (used for SPI devices with PonyProg 2000) or a custom made serial
bitbanging programmer named "serbang". The optional type parameter accepts the
values "si_prog" (default) or "serbang".
Information about the SI-Prog adapter can be found at its website
⟨http://www.lancos.com/siprogsch.html⟩.
An example call to flashrom is
flashrom -p pony_spi:dev=/dev/ttyS0,type=serbang
Please note that while USB-to-serial adapters work under certain circumstances,
this slows down operation considerably.
ogp_spi programmer
The flash ROM chip to access must be specified with the rom parameter.
flashrom -p ogp_spi:rom=name
Where name is either cprom or s3 for the configuration ROM and bprom or bios for
the BIOS ROM. If more than one card supported by the ogp_spi programmer is
installed in your system, you have to specify the PCI address of the card you want
to use with the pci= parameter as explained in the nic3com et al. section above.
linux_mtd programmer
You may specify the MTD device to use with the
flashrom -p linux_mtd:dev=/dev/mtdX
syntax where /dev/mtdX is the Linux device node for your MTD device. If left
unspecified the first MTD device found (e.g. /dev/mtd0) will be used by default.
Please note that the linux_mtd driver only works on Linux.
linux_spi programmer
You have to specify the SPI controller to use with the
flashrom -p linux_spi:dev=/dev/spidevX.Y
syntax where /dev/spidevX.Y is the Linux device node for your SPI controller.
In case the device supports it, you can set the SPI clock frequency with the
optional spispeed parameter. The frequency is parsed as kilohertz. Example that
sets the frequency to 8 MHz:
flashrom -p linux_spi:dev=/dev/spidevX.Y,spispeed=8000
Please note that the linux_spi driver only works on Linux.
mstarddc_spi programmer
The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors,
that allows exchanging information between a computer and attached displays. Its
most common uses are getting display capabilities through EDID (at I2C address
0x50) and sending commands to the display using the DDC/CI protocol (at address
0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC
firmware flash (connected to the Soc through another SPI bus) using an In-System
Programming (ISP) port, usually at address 0x49. This flashrom module allows the
latter via Linux's I2C driver.
IMPORTANT: Before using this programmer, the display MUST be in standby mode, and
only connected to the computer that will run flashrom using a VGA cable, to an
inactive VGA output. It absolutely MUST NOT be used as a display during the
procedure!
You have to specify the DDC/I2C controller and I2C address to use with the
flashrom -p mstarddc_spi:dev=/dev/i2c-X:YY
syntax where /dev/i2c-X is the Linux device node for your I2C controller connected
to the display's DDC channel, and YY is the (hexadecimal) address of the MSTAR ISP
port (address 0x49 is usually used). Example that uses I2C controller /dev/i2c-1
and address 0x49:
flashrom -p mstarddc_spi:dev=/dev/i2c-1:49
It is also possible to inhibit the reset command that is normally sent to the
display once the flashrom operation is completed using the optional noreset
parameter. A value of 1 prevents flashrom from sending the reset command. Example
that does not reset the display at the end of the operation:
flashrom -p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1
Please note that sending the reset command is also inhibited if an error occurred
during the operation. To send the reset command afterwards, you can simply run
flashrom once more, in chip probe mode (not specifying an operation), without the
noreset parameter, once the flash read/write operation you intended to perform has
completed successfully.
Please also note that the mstarddc_spi driver only works on Linux.
ch341a_spi programmer
The WCH CH341A programmer does not support any parameters currently. SPI frequency is
fixed at 2 MHz, and CS0 is used as per the device.
ni845x_spi programmer
An optional voltage parameter could be used to specify the IO voltage. This
parameter is available for the NI USB-8452 device. The default unit is Volt if no
unit is specified. You can use mV, milliVolt, V or Volt as unit specifier. Syntax
is
flashrom -p ni845x_spi:voltage=value
where value can be 1.2V, 1.5V, 1.8V, 2.5V, 3.3V or the equivalent in mV.
In the case if none of the programmer's supported IO voltage is within the
supported voltage range of the detected flash chip the flashrom will abort the
operation (to prevent damaging the flash chip). You can override this behaviour by
passing "yes" to the ignore_io_voltage_limits parameter (for e.g. if you are using
an external voltage translator circuit). Syntax is
flashrom -p ni845x_spi:ignore_io_voltage_limits=yes
You can use the serial parameter to explicitly specify which connected NI USB-845x
device should be used. You should use your device's 7 digit hexadecimal serial
number. Usage example to select the device with 1230A12 serial number:
flashrom -p ni845x_spi:serial=1230A12
An optional spispeed parameter specifies the frequency of the SPI bus. Syntax is
flashrom -p ni845x_spi:spispeed=frequency
where frequency should a number corresponding to the desired frequency in kHz. The
maximum frequency is 12 MHz (12000 kHz) for the USB-8451 and 50 MHz (50000 kHz) for
the USB-8452. The default is a frequency of 1 MHz (1000 kHz).
An optional cs parameter specifies which target chip select line should be used.
Syntax is
flashrom -p ni845x_spi:csnumber=value
where value should be between 0 and 7 By default the CS0 is used.
digilent_spi programmer
An optional spispeed parameter specifies the frequency of the SPI bus. Syntax is
flashrom -p digilent_spi:spispeed=frequency
where frequency can be 62.5k, 125k, 250k, 500k, 1M, 2M or 4M (in Hz). The default
is a frequency of 4 MHz.
dirtyjtag_spi programmer
An optional freq parameter specifies the frequency of the SPI bus. Syntax is
flashrom -p dirtyjtag_spi:spispeed=frequency
where spispeed can be anyvalueinhertz,kilohertzormegahertzsupportedbythe
programmer. The default is a frequency of 100 KHz.
jlink_spi programmer
This module supports SEGGER J-Link and compatible devices.
The MOSI signal of the flash chip must be attached to TDI pin of the programmer,
MISO to TDO and SCK to TCK. The chip select (CS) signal of the flash chip can be
attached to different pins of the programmer which can be selected with the
flashrom -p jlink_spi:cs=pin
syntax where pin can be either TRST or RESET. The default pin for chip select is
RESET. Note that, when using RESET, it is normal that the indicator LED blinks
orange or red.
Additionally, the VTref pin of the programmer must be attached to the logic level
of the flash chip. The programmer measures the voltage on this pin and generates
the reference voltage for its input comparators and adapts its output voltages to
it.
Pinout for devices with 20-pin JTAG connector:
+-------+
| 1 2 | 1: VTref 2:
| 3 4 | 3: TRST 4: GND
| 5 6 | 5: TDI 6: GND
+-+ 7 8 | 7: 8: GND
| 9 10 | 9: TCK 10: GND
| 11 12 | 11: 12: GND
+-+ 13 14 | 13: TDO 14:
| 15 16 | 15: RESET 16:
| 17 18 | 17: 18:
| 19 20 | 19: PWR_5V 20:
+-------+
If there is more than one compatible device connected, you can select which one
should be used by specifying its serial number with the
flashrom -p jlink_spi:serial=number
syntax where number is the serial number of the device (which can be found for
example in the output of lsusb -v).
The SPI speed can be selected by using the
flashrom -p jlink_spi:spispeed=frequency
syntax where frequency is the SPI clock frequency in kHz. The maximum speed
depends on the device in use.
The power=on option can be used to activate the 5 V power supply (PWR_5V) of the J-
Link during a flash operation.
stlinkv3_spi programmer
This module supports SPI flash programming through the STMicroelectronics STLINK V3
programmer/debugger's SPI bridge interface
flashrom -p stlinkv3_spi
If there is more than one compatible device connected, you can select which one
should be used by specifying its serial number with the
flashrom -p stlinkv3_spi:serial=number
syntax where number is the serial number of the device (which can be found for
example in the output of lsusb -v).
The SPI speed can be selected by using the
flashrom -p stlinkv3_spi:spispeed=frequency
syntax where frequency is the SPI clock frequency in kHz. If the passed frequency
is not supported by the adapter the nearest lower supported frequency will be used.
realtek_mst_i2c_spi , parade_lspcon ,and mediatek_i2c_spi programmers
These programmers tunnel SPI commands through I2C-connected devices. The I2C bus
over which communication occurs must be specified either by device path with the
devpath option:
flashrom -p realtek_mst_i2c_spi:devpath=/dev/i2c-8
or by a bus number with the bus option, which implies a device path like /dev/i2c-N
where N is the specified bus number:
flashrom -p parade_lspcon:bus=8
realtek_mst_i2c_spi programmer
This programmer supports SPI flash programming for chips attached to Realtek
DisplayPort MST hubs, themselves accessed through I2C (tunneling SPI flash commands
through the MST hub's I2C connection with the host).
In-system programming (ISP) mode
The reset_mcu and enter_isp options provide control over device mode changes, where
each can be set to 0 or 1 to enable or disable the corresponding mode transition.
enter_isp defaults to 1, and if enabled will issue commands to the MST hub when
beginning operation to put it into ISP mode.
reset_mcu defaults to 0, and if enabled will issue a reset command to the MST hub
on programming completion, causing it to exit ISP mode and to reload its own
firmware from flash.
allow_brick defaults to no, however must be set explicitly to "yes" to allow the
driver to run if you are sure you have a MST chip.
The hub must be in ISP mode for SPI flash access to be possible, so it is usually
only useful to disable enter_isp if an earlier invocation avoided resetting it on
completion. For instance, to erase the flash and rewrite it with the contents of a
file without resetting in between (which could render it nonfunctional if
attempting to load firmware from a blank flash):
flashrom -p realtek_mst_i2c_spi:bus=0,enter_isp=1,reset_mcu=0 -E
flashrom -p realtek_mst_i2c_spi:bus=0,enter_isp=0,reset_mcu=1 -w new.bin
parade_lspcon programmer
This programmer supports SPI flash programming for chips attached to Parade
Technologies DisplayPort-to-HDMI level shifter/protocol converters (LSPCONs), e.g.
the PS175. Communication to the SPI flash is tunneled through the LSPCON over I2C.
mediatek_i2c_spi programmer
This programmer supports SPI flash programming for chips attached to some Mediatek
display controllers, themselves accessed through I2C (tunneling SPI flash commands
through an I2C connection with the host).
The programmer is designed to support the TSUMOP82JUQ integrated display driver and
scaler as used in the Google Meet Series One Desk 27 (which runs a version of
ChromeOS and uses flashrom in its tsum-scaler-updater scripts that ship with the
OS). Other chips may use compatible protocols but have not been tested with this
programmer, and external chip IOs may need to be controlled through other non-
flashrom means to configure the chip in order for it to operate as expected.
devpath and bus options select the I2C bus to use, as described previously.
allow_brick defaults to no, and must explicitly be set to "yes" in order for the
programmer to operate. This is required because there is no mechanism in the driver
to positively identify that a given I2C bus is actually connected to a supported
device.
EXAMPLES
To back up and update your BIOS, run
flashrom -p internal -r backup.rom -o backuplog.txt
flashrom -p internal -w newbios.rom -o writelog.txt
Please make sure to copy backup.rom to some external media before you try to write. That
makes offline recovery easier.
If writing fails and flashrom complains about the chip being in an unknown state, you can
try to restore the backup by running
flashrom -p internal -w backup.rom -o restorelog.txt
If you encounter any problems, please contact us and supply backuplog.txt, writelog.txt
and restorelog.txt. See section BUGS for contact info.
EXIT STATUS
flashrom exits with 0 on success, 1 on most failures but with 3 if a call to mmap() fails.
REQUIREMENTS
flashrom needs different access permissions for different programmers.
internal needs raw memory access, PCI configuration space access, raw I/O port access
(x86) and MSR access (x86).
atavia needs PCI configuration space access.
nic3com, nicrealtek and nicnatsemi need PCI configuration space read access and raw I/O
port access.
atahpt needs PCI configuration space access and raw I/O port access.
gfxnvidia, drkaiser and it8212 need PCI configuration space access and raw memory access.
rayer_spi needs raw I/O port access.
raiden_debug_spi need access to the respective USB device via libusb API version 1.0.
satasii, nicintel, nicintel_eeprom and nicintel_spi need PCI configuration space read
access and raw memory access.
satamv and atapromise need PCI configuration space read access, raw I/O port access and
raw memory access.
serprog needs TCP access to the network or userspace access to a serial port.
buspirate_spi needs userspace access to a serial port.
ft2232_spi, usbblaster_spi and pickit2_spi need access to the respective USB device via
libusb API version 0.1.
ch341a_spi and dediprog need access to the respective USB device via libusb API version
1.0.
dummy needs no access permissions at all.
internal, nic3com, nicrealtek, nicnatsemi, gfxnvidia, drkaiser, satasii, satamv, atahpt,
atavia and atapromise have to be run as superuser/root, and need additional raw access
permission.
serprog, buspirate_spi, dediprog, usbblaster_spi, ft2232_spi, pickit2_spi, ch341a_spi,
digilent_spi and dirtyjtag_spi can be run as normal user on most operating systems if
appropriate device permissions are set.
ogp needs PCI configuration space read access and raw memory access.
realtek_mst_i2c_spi and parade_lspcon need userspace access to the selected I2C bus.
On OpenBSD, you can obtain raw access permission by setting securelevel=-1 in
/etc/rc.securelevel and rebooting, or rebooting into single user mode.
BUGS
You can report bugs, ask us questions or send success reports via our communication
channels listed here: https://www.flashrom.org/Contact.
Also, we provide a pastebin service ⟨https://paste.flashrom.org⟩ that is very useful to
share logs without spamming the communication channels.
Laptops
Using flashrom on older laptops is dangerous and may easily make your hardware unusable.
flashrom will attempt to detect if it is running on a susceptible laptop and restrict
flash-chip probing for safety reasons. Please see the detailed discussion of this topic
and associated flashrom options in the Laptops paragraph in the internal programmer
subsection of the PROGRAMMER-SPECIFIC INFORMATION section and the information in our wiki
⟨https://flashrom.org/Laptops⟩.
One-time programmable (OTP) memory and unique IDs
Some flash chips contain OTP memory often denoted as "security registers". They usually
have a capacity in the range of some bytes to a few hundred bytes and can be used to give
devices unique IDs etc. flashrom is not able to read or write these memories and may
therefore not be able to duplicate a chip completely. For chip types known to include OTP
memories a warning is printed when they are detected.
Similar to OTP memories are unique, factory programmed, unforgeable IDs. They are not
modifiable by the user at all.
LICENSE
flashrom is covered by the GNU General Public License (GPL), version 2. Some files are
additionally available under any later version of the GPL.
COPYRIGHT
Please see the individual files.
AUTHORS
Andrew Morgan
Anastasia Klimchuk
Carl-Daniel Hailfinger
Claus Gindhart
David Borg
David Hendricks
Dominik Geyer
Edward O'Callaghan
Eric Biederman
Giampiero Giancipoli
Helge Wagner
Idwer Vollering
Joe Bao
Joerg Fischer
Joshua Roys
Kyösti Mälkki
Luc Verhaegen
Li-Ta Lo
Mark Marshall
Markus Boas
Mattias Mattsson
Michael Karcher
Nikolay Petukhov
Patrick Georgi
Peter Lemenkov
Peter Stuge
Reinder E.N. de Haan
Ronald G. Minnich
Ronald Hoogenboom
Sean Nelson
Stefan Reinauer
Stefan Tauner
Stefan Wildemann
Stephan Guilloux
Steven James
Urja Rannikko
Uwe Hermann
Wang Qingpei
Yinghai Lu
some others, please see the flashrom git history for details.
All still active authors can be reached via the mailing list ⟨flashrom@flashrom.org⟩.
This manual page was written by Uwe Hermann ⟨uwe@hermann-uwe.de⟩, Carl-Daniel Hailfinger,
Stefan Tauner and others. It is licensed under the terms of the GNU GPL (version 2 or
later).