Provided by: inetutils-inetd_2.4-2ubuntu1_amd64 
NAME
inetd — internet “super-server”
SYNOPSIS
inetd [option ...] [conf-file [conf-dir]] ...
DESCRIPTION
The inetd program should be run at boot time by /etc/rc (see rc(8)). It then listens for
connections on certain internet sockets. When a connection is found on one of its sockets,
it decides what service the socket corresponds to, and invokes a program to service the
request. The server program is invoked with the service socket as its standard input,
output and error descriptors. After the program is finished, inetd continues to listen on
the socket (except in some cases which will be described below). Essentially, inetd allows
running one daemon to invoke several others, reducing load on the system.
OPTIONS
The options available for inetd:
-d, --debug
Turns on debugging.
--environment
Pass local and remote address data via environment variables. See ENVIRONMENT below.
-p, --pidfile [filename]
Specifies the pidfile to use instead of the default. When a filename is not
specified, that disables writing a pidfile.
-R, --rate rate
Specifies the maximum number of times a service can be invoked in one minute; the
default is 40.
--resolve
Resolve local and remote IP addresses and pass them to the server program via
TCPLOCALHOST and TCPREMOTEHOST environment variables. See ENVIRONMENT below. This
option implies --environment.
-V, --version
Shows the version.
-?, --help
Shows the help.
--usage
Shows the usage message.
OPERATION
Upon execution, inetd reads its configuration information from a configuration file on the
command line, by default, /etc/inetd.conf and /etc/inetd.d. If the configuration pathname
is a directory, all the files in the directory are read like a configuration file. All of
the configuration files are read and merged. There must be an entry for each field in the
configuration file, with entries for each field separated by a tab or a space. Comments are
denoted by a "#" at the beginning of a line. The fields of the configuration file are as
follows:
service name
socket type
protocol
wait/nowait[.max]
user[:group]
server program
server program arguments
There are two types of services that inetd can start: standard and TCPMUX. A standard
service has a well-known port assigned to it; it may be a service that implements an
official Internet standard or is a BSD-specific service. As described in RFC 1078, TCPMUX
services are nonstandard services that do not have a well-known port assigned to them. They
are invoked from inetd when a program connects to the “tcpmux” well-known port and specifies
the service name. This feature is useful for adding locally-developed servers.
The service-name entry is the name of a valid service in the file /etc/services. For
“internal” services (discussed below), the service name must be the official name of the
service (that is, the first entry in /etc/services). For TCPMUX services, the value of the
service-name field consists of the string “tcpmux” followed by a slash and the locally-
chosen service name. The service names listed in /etc/services and the name “help” are
reserved. Try to choose unique names for your TCPMUX services by prefixing them with your
organization's name and suffixing them with a version number.
The socket-type should be one of “stream”, “dgram”, “raw”, “rdm”, or “seqpacket”, depending
on whether the socket is a stream, datagram, raw, reliably delivered message, or sequenced
packet socket. TCPMUX services must use “stream”.
The protocol must be a valid protocol as given in /etc/protocols. Examples might be “tcp”
or “udp”. TCPMUX services must use “tcp”. By default the protocols will only listen on
IPv4 connections. To modify this behavior per service, either “4” or “6” can be appended to
the protocol name, such as “udp4” or “tcp6” to accept only IPv4 UDP connections or both IPv4
and IPv6 TCP connections respectively. To restrict to IPv6-only connections, “6only” can be
appended to the protocol name, such as “tcp6only”.
The wait/nowait[.max] entry specifies whether the server that is invoked by inetd will take
over the socket associated with the service access point, and thus whether inetd should wait
for the server to exit before listening for new service requests. Datagram servers must use
“wait”, as they are always invoked with the original datagram socket bound to the specified
service address. These servers must read at least one datagram from the socket before
exiting. If a datagram server connects to its peer, freeing the socket so inetd can
received further messages on the socket, it is said to be a “multi-threaded” server; it
should read one datagram from the socket and create a new socket connected to the peer. It
should fork, and the parent should then exit to allow inetd to check for new service
requests to spawn new servers. Datagram servers which process all incoming datagrams on a
socket and eventually time out are said to be “single-threaded”. Comsat(8), (biff(1)) and
talkd(8) are both examples of the latter type of datagram server. Tftpd(8) is an example of
a multi-threaded datagram server. The optional “max” suffix (separated from “wait” or
“nowait” by a dot) specifies the maximum number of times a service can be invoked in one
minute; the default is 40. If a service exceeds this limit, inetd will log the problem and
stop servicing requests for the specific service for ten minutes. See also the -R option
above.
Servers using stream sockets generally are multi-threaded and use the “nowait” entry.
Connection requests for these services are accepted by inetd, and the server is given only
the newly-accepted socket connected to a client of the service. Most stream-based services
operate in this manner. Stream-based servers that use “wait” are started with the listening
service socket, and must accept at least one connection request before exiting. Such a
server would normally accept and process incoming connection requests until a timeout.
TCPMUX services must use “nowait”.
The optional “max” suffix (separated from “wait” or “nowait” by a dot) is a decimal number
that specifies the maximum number of server instances that may be spawned from inetd within
an interval of 60 seconds. It overrides the settings of the -R command line option.
The user entry should contain the user name, and the optional group name (separated from
“user” by a semicolon or a dot) of the user (and group) as whom the server should run. This
allows for servers to be given less permission than root.
The server-program entry should contain the pathname of the program which is to be executed
by inetd when a request is found on its socket. If inetd provides this service internally,
this entry should be “internal”.
The server program arguments should be just as arguments normally are, starting with
argv[0], which is the name of the program. If the service is provided internally, the word
“internal” should take the place of this entry.
The inetd program provides several “trivial” services internally by use of routines within
itself. These services are “echo”, “discard”, “chargen” (character generator), “daytime”
(human readable time), and “time” (machine readable time, in the form of the number of
seconds since midnight, January 1, 1900). All of these services are tcp based. For details
of these services, consult the appropriate RFC from the Network Information Center.
The inetd program rereads its configuration file when it receives a hangup signal, SIGHUP.
Services may be added, deleted or modified when the configuration file is reread.
TCPMUX
RFC 1078 describes the TCPMUX protocol: "A TCP client connects to a foreign host on TCP port
1. It sends the service name followed by a carriage-return line-feed <CRLF>. The service
name is never case sensitive. The server replies with a single character indicating
positive (+) or negative (-) acknowledgment, immediately followed by an optional message of
explanation, terminated with a <CRLF>. If the reply was positive, the selected protocol
begins; otherwise the connection is closed." The program is passed the TCP connection as
file descriptors 0 and 1.
If the TCPMUX service name begins with a "+", inetd returns the positive reply for the
program. This allows you to invoke programs that use stdin/stdout without putting any
special server code in them.
The special service name “help” causes inetd to list TCPMUX services in inetd.conf.
ENVIRONMENT
If a connection is made with a streaming protocol (TCP) and if --environment option has been
given, inetd will set the following environment variables before starting the program:
PROTO: always "TCP".
TCPLOCALIP: the local IP address of the interface which accepted the connection.
TCPLOCALPORT: the port number on which the TCP connection was established.
TCPREMOTEIP: the IP address of the remote client.
TCPREMOTEPORT: the port number on the client side of the TCP connection.
In addition, if given the --environment or --resolve options, inetd will set the following
environment variables:
TCPLOCALHOST: the DNS name of TCPLOCALIP.
TCPREMOTEHOST: the DNS name of TCPREMOTEIP.
EXAMPLES
Here are several example service entries for the various types of services:
ftp stream tcp nowait root /usr/libexec/ftpd ftpd -l
ntalk dgram udp wait root /usr/libexec/ntalkd ntalkd
tcpmux/+date stream tcp nowait guest /bin/date date
tcpmux/phonebook stream tcp nowait guest /usr/local/bin/phonebook phonebook
ERROR MESSAGES
The inetd server logs error messages using syslog(3). Important error messages and their
explanations are:
service/protocol server failing (looping), service terminated.
The number of requests for the specified service in the past minute exceeded the limit. The
limit exists to prevent a broken program or a malicious user from swamping the system. This
message may occur for several reasons: 1) there are lots of hosts requesting the service
within a short time period, 2) a 'broken' client program is requesting the service too
frequently, 3) a malicious user is running a program to invoke the service in a 'denial of
service' attack, or 4) the invoked service program has an error that causes clients to retry
quickly. Use the [-R] option, as described above, to change the rate limit. Once the limit
is reached, the service will be re-enabled automatically in 10 minutes.
service/protocol: No such user 'user', service ignored
service/protocol: getpwnam: user: No such user
No entry for user exists in the passwd file. The first message occurs when inetd (re)reads
the configuration file. The second message occurs when the service is invoked.
service: can't set uid number
service: can't set gid number
The user or group ID for the entry's user is invalid.
SEE ALSO
comsat(8), fingerd(8), ftpd(8), rexecd(8), rlogind(8), rshd(8), telnetd(8), tftpd(8)
BUGS
The environment variables (see ENVIRONMENT) are set only for TCP IPv4 nowait connections.
HISTORY
The inetd command appeared in 4.3BSD. TCPMUX is based on code and documentation by Mark
Lottor.