Provided by: open-iscsi_2.1.8-1ubuntu1_amd64 
NAME
iscsiadm - open-iscsi administration utility
SYNOPSIS
iscsiadm -m discoverydb [-hV] [-d debug_level] [-P printlevel] [-I iface
-t type -p ip:port [-lD] ] | [ [-p ip:port -t type] [-o operation] [-n name] [-v value]
[-lD] ]
iscsiadm -m discovery [-hV] [-d debug_level] [-P printlevel] [-I iface] [-t type] [-p
ip:port] [-l]
iscsiadm -m node [-hV] [-d debug_level] [-P printlevel] [-L all,manual,automatic,onboot]
[-W] [-U all,manual,automatic,onboot] [-S] [ [-T targetname -p ip:port -I iface]
[-l|-u|-R|-s] ] [ [-o operation] [-n name] [-v value] [-p ip:port] ]
iscsiadm -m session [-hV] [-d debug_level] [-P printlevel] [-r sessionid|sysfsdir [-R]
[-u|-s|-o new] ]
iscsiadm -m iface [-hV] [-d debug_level] [-P printlevel] [-I ifacename | -H hostno|MAC] [
[-o operation] [-n name] [-v value] ] [ -C ping [-a ip] [-b packetsize] [-c count] [-i
interval] ]
iscsiadm -m fw [-d debug_level] [-l] [-W] [-n name] [-v value]
iscsiadm -m host [-P printlevel] [-H hostno|MAC] [ [-C chap [-x chap_tbl_idx] ] | [-C
flashnode [-A portal_type] [-x flashnode_idx] ] | [-C stats] ] [ [-o operation] [-n name]
[-v value] ]
iscsiadm -k priority
DESCRIPTION
The iscsiadm utility is a command-line tool allowing discovery and login to iSCSI targets,
as well as access and management of the open-iscsi database.
Open-iscsi does not use the term node as defined by the iSCSI RFC, where a node is a
single iSCSI initiator or target. Open-iscsi uses the term node to refer to a portal on a
target.
For session mode, a session id (sid) is used. The sid of a session can be found by running
iscsiadm -m session -P 1. The session id and sysfs path are not currently persistent and
is partially determined by when the session is setup.
NOTES
Many of the node and discovery operations require that the iSCSI daemon (iscsid) be
running. If running on a system that uses systemd, the daemon may start up automatically,
if enabled, when needed.
Open-iscsi has two groups of files it needs to store or get access to, while running: the
HOMEDIR and the DBROOT. The following describes them:
Home Directory
The home directory for open-iscsi is /etc/iscsi. This is where it keeps it's
configuration file (iscsid.conf) and it's initiator name file
(initiatorname.iscsi).
Database Root Directory
The database root directory for open-iscsi is /etc/iscsi. This is where it keeps
its flat database files, such as it's list of nodes (see below).
OPTIONS
-a, --ip=ipaddr
ipaddr can be IPv4 or IPv6.
This option is only valid for ping submode.
-A, --portal_type=[ipv4|ipv6]
Specify the portal type for the new flash node entry to be created.
This option is only valid for flashnode submode of host mode and only with new
operation.
-b, --packetsize=packetsize
Specify the ping packetsize.
This option is only valid for ping submode.
-c, --count=count
count specifies the number of ping iterations.
This option is only valid for ping submode.
-C, --submode=op
Specify the submode for mode. op must be name of submode.
Currently iscsiadm supports ping as a submode for iface. For example:
iscsiadm -m iface -I ifacename -C ping -a ipaddr -b packetsize -c count -i interval
For host, it supports chap, flashnode and stats as submodes. For example:
iscsiadm -m host -H hostno -C chap -x chap_tbl_idx -o operation
iscsiadm -m host -H hostno -C flashnode -x flashnode_idx -o operation
iscsiadm -m host -H hostno -C stats
-d, --debug=debug_level
print debugging information. Valid values for debug_level are 0 to 8.
-h, --help
display help text and exit
-H, --host=[hostno|MAC]
The host argument specifies the SCSI host to use for the operation. It can be the
scsi host number assigned to the host by the kernel's scsi layer, or the MAC
address of a scsi host.
-i, --interval=interval
interval specifies the delay between two ping iterations.
This option is only valid for ping submode.
-I, --interface=[iface]
The interface argument specifies the iSCSI interface to use for the operation.
iSCSI interfaces (iface) are defined in /etc/iscsi/ifaces. For hardware iSCSI (e.g.
qla4xxx) the iface configuration must have the hardware address (iface.hwaddress =
port's MAC address) and the driver/transport_name (iface.transport_name). The
iface's name is then the filename of the iface configuration. For software iSCSI,
the iface configuration must have either the hardware address (iface.hwaddress), or
the network layer's interface name (iface.net_ifacename), and it must have the
driver/transport_name.
The available drivers/iscsi_transports are tcp (software iSCSI over TCP/IP), iser
(software iSCSI over InfiniBand), qla4xxx (Qlogic 4XXXX and 82XXX HBAs), cxgb3i and
cxgb4i (Chelsio T3 and T4 adapters), bnx2i (QLogic Netextreme II adapters),
be2iscsi (Emulex 10G adapter), qedi (QLogic QEDI 25/40/100Gb adapter), and ocs
(Emulex One Connect storage). Some of these are considered experimental, as they
are not fully tested.
The hwaddress is the MAC address or for software iSCSI it may be the special value
default which directs the initiator to not bind the session to a specific hardware
resource and instead allow the network or InfiniBand layer to decide what to do.
There is no need to create an iface configuration with the default behavior. If you
do not specify an iface, then the default behavior is used.
As mentioned above there is a special iface name default. There are others which do
not bind the session to a specific card, but instead bind the session to the
transport: iser, cxgb3i, cxgb4i, and bnx2i.
In discovery mode multiple interfaces can be specified by passing in multiple
-I/--interface instances. For example:
sh# iscsiadm -m discoverydb -t st -p ip:port -I iface0 -I iface2 --discover
Will direct iscsiadm to setup the node db to create records which will create
sessions through the two interfaces passed in.
In node mode, only a single interface is supported in each call to iscsiadm.
This option is valid for discovery, node and iface modes.
-k, --killiscsid=[priority]
Currently priority must be zero. This will immediately stop all iscsid operations
and shutdown iscsid. It does not logout any sessions. Running this command is the
same as doing killall iscsid. Neither should normally be used, because if iscsid is
doing error recovery or if there is an error while iscsid is not running, the
system may not be able to recover. This command and iscsid's SIGTERM handling are
experimental.
-D, --discover
Discover targets using the discovery record with the recid matching the the
discovery type and portal passed in. If there is no matching record, it will be
created using the iscsid.conf discovery settings. This must be passed in to
discoverydb mode to instruct iscsiadm to perform discovery.
This option is only valid for SendTargets discovery mode.
-l, --login
For node and fw modes, login to a specified record. For discovery mode, login to
all discovered targets.
This option is only valid for discovery, node, and fw modes. For fw mode only,
name and value pairs can optionally be passed in, so that those values get used for
the sessions created. In this case, no op is needed, since update is assumed.
-L, --loginall=[all|manual|automatic|onboot]
For node mode, login to all sessions with the node or conn startup values passed in
or all running session, except ones marked onboot, if all is passed in.
This option is only valid for node mode (it is valid but not functional for session
mode).
-W, ---no_wait
In node, discovery, or fw (firmware) mode, do not wait for a response from the
target(s). This means that success will be returned if the command is able to send
the login requests, whether or not they succeed. In this case, it will be up to the
caller to poll for success (i.e. session creation).
-m, --mode op
specify the mode. op must be one of discovery, discoverydb, node, fw, host, iface
or session.
If no other options are specified: for discovery, discoverydb and node mode, all of
their respective records are displayed; for session mode, all active sessions and
connections are displayed; for fw mode, all boot firmware values are displayed; for
host mode, all iSCSI hosts are displayed; and for iface mode, all interfaces setup
in /etc/iscsi/ifaces are displayed.
-n, --name=name
In node mode, specify a field name in a record. In flashnode submode of host mode,
specify name of the flash node parameter.
For use with the update operator.
-o, --op=op
Specifies a database operator op. op must be one of new, delete, update, show or
nonpersistent.
For iface mode, apply and applyall are also applicable.
For flashnode submode of host mode, login and logout are also applicable.
This option is valid for all modes except fw. Delete should not be used on a
running session. If it is iscsiadm will stop the session and then delete the
record.
An op of new creates a new database record for a given object. In node mode, the
recid is the target name and portal (IP:port). In iface mode, the recid is the
iface name. In discovery mode, the recid is the portal and discovery type.
In session mode, the new operation logs in a new session using the same node
database and iface information as the specified session.
In discovery mode, if the recid and new operation is passed in, but the --discover
argument is not passed in, then iscsiadm will only create a discovery record (it
will not perform discovery). If the --discover argument is passed in with the
portal and discovery type, then iscsiadm will create the discovery record if
needed, and it will create records for portals returned by the target that do not
yet have a node DB record.
Setting op to delete deletes the specified recid. In discovery mode, if iscsiadm is
performing discovery, it will delete records for portals that are no longer
returned.
Setting op to update will update the recid with name to the specified value. In
discovery mode, if iscsiadm is performing discovery the recid, name and value
arguments are not needed. The update operation will operate on the portals returned
by the target, and will update the node records with information from the
configuration file and command line.
The op value of show is the default behaviour for node, discovery and iface mode.
It is also used when there are no commands passed into session mode and a running
sid is passed in. If name and value are passed in, they are currently ignored in
show mode.
An op value of nonpersistent instructs iscsiadm to not manipulate the node DB.
An op value of apply will cause the network settings to take effect on the
specified iface.
An op value of applyall will cause the network settings to take effect on all the
ifaces whose MAC address or host number matches that of the specific host.
An op value of login will log into the specified flash node entry.
An op value of logout does the logout from the given flash node entry.
-p, --portal=ip[:port]
Use target portal with IP address ip and port port. If port is not passed in the
default value of 3260 is used.
IPv6 addresses can be specified as [ddd.ddd.ddd.ddd]:port or ddd.ddd.ddd.ddd.
Hostnames can also be used for the ip argument.
This option is only valid for discovery, or for node operations with the new
operator.
This should be used along with --target in node mode, to specify what the open-
iscsi documents refer to as a node or node record. Note: open-iscsi's use of the
word node, does not match the iSCSI RFC's iSCSI Node term.
-P, --print=printlevel
If in node mode print nodes in tree format. If in session mode print sessions in
tree format. If in discovery mode print the nodes in tree format.
-T, --targetname=targetname
Use target targetname.
This should be used along with --portal in node mode, to specify what the open-
iscsi documents refer to as a node or node record. Note: open-iscsi's use of the
word node, does not match the iSCSI RFC's iSCSI Node term.
-r, --sid=sid | sysfsdir
Use session ID sid. The session ID of a session can be found from running iscsiadm
in session mode with the --info argument.
Instead of a session ID, a sysfs path containing the session can be used. For
example using one of the following:
/sys/devices/platform/hostH/sessionS/targetH:B:I/H:B:I:L,
/sys/devices/platform/hostH/sessionS/targetH:B:I, or
/sys/devices/platform/hostH/sessionS, for the sysfsdir argument would result in the
session with session ID S to be used.
sid | sysfsdir is only required for session mode.
-R, --rescan
In session mode, if sid is also passed in, rescan the session. If no sid has been
passed in rescan all running sessions.
In node mode, rescan a session running through the target, portal, iface tuple
passed in.
-s, --stats
Display session statistics. This option when used with host mode, displays host
statistics.
-S, --show
When displaying records, do not hide masked values, such as the CHAP secret
(password).
This option is only valid for node and session mode.
-t, --type=type
type must be sendtargets (or abbreviated as st), slp, isns or fw. Currently only
sendtargets, fw, and iSNS are supported, see the DISCOVERY TYPES section.
This option is only valid for discovery mode.
-u, --logout
Logout for the specified record.
This option is only valid for node and session mode.
-U, --logoutall=[all,manual,automatic|onboot]
Logout of all sessions with the node or conn startup values passed in or all
running sessions, except ones marked onboot, if all is passed in.
This option is only valid for node mode (it is valid but not functional for session
mode).
-v, --value=value
Specify a value for use with the update operator, or for firmware login mode.
This option is only valid for node mode and flashnode submode of host mode.
-V, --version
Display version and exit.
-x, --index=index
Specify the index of the entity to operate on.
This option is only valid for chap and flashnode submodes of host mode.
DISCOVERY TYPES
iSCSI defines 3 discovery types: SendTargets, SLP, and iSNS.
A special discovery type called fw (for firmware) is also supported, for discovering
firmware interfaces, and populating the interface database in the process.
SendTargets
A native iSCSI protocol which allows each iSCSI target to send a list of available
targets to the initiator.
SLP Optionally an iSCSI target can use the Service Location Protocol (SLP) to announce
the available targets. The initiator can either implement SLP queries directly or
can use a separate tool to acquire the information about available targets.
iSNS iSNS (Internet Storage Name Service) records information about storage volumes
within a larger network. To utilize iSNS, pass the address and optionally the port
of the iSNS server to do discovery to.
fw Firmware mode. Several NICs and systems contain a mini iSCSI initiator which can
be used for boot. To get the values used for boot the fw option can be used. Doing
fw discovery does not store persistent records in the node or discovery DB, because
the values are stored in the system's or NIC's resource.
Performing fw discovery will print the portals, like with other discovery methods.
To see other settings like CHAP values and initiator settings, like you would in
node mode, run iscsiadm -m fw.
Note that the SLP implementation is under development and currently is not supported.
EXIT STATUS
On success 0 is returned. On error one of the return codes below will be returned.
Commands that operate on multiple objects (sessions, records, etc), iscsiadm/iscsistart
will return the first error that is encountered. iscsiadm/iscsistart will attempt to
execute the operation on the objects it can. If no objects are found
ISCSI_ERR_NO_OBJS_FOUND is returned.
0 ISCSI_SUCCESS - command executed successfully.
1 ISCSI_ERR - generic error code.
2 ISCSI_ERR_SESS_NOT_FOUND - session could not be found.
3 ISCSI_ERR_NOMEM - could not allocate resource for operation.
4 ISCSI_ERR_TRANS - connect problem caused operation to fail.
5 ISCSI_ERR_LOGIN - generic iSCSI login failure.
6 ISCSI_ERR_IDBM - error accessing/managing iSCSI DB.
7 ISCSI_ERR_INVAL - invalid argument.
8 ISCSI_ERR_TRANS_TIMEOUT - connection timer expired while trying to connect.
9 ISCSI_ERR_INTERNAL - generic internal iscsid/kernel failure.
10 ISCSI_ERR_LOGOUT - iSCSI logout failed.
11 ISCSI_ERR_PDU_TIMEOUT - iSCSI PDU timed out.
12 ISCSI_ERR_TRANS_NOT_FOUND - iSCSI transport module not loaded in kernel or iscsid.
13 ISCSI_ERR_ACCESS - did not have proper OS permissions to access iscsid or execute
iscsiadm command.
14 ISCSI_ERR_TRANS_CAPS - transport module did not support operation.
15 ISCSI_ERR_SESS_EXISTS - session is logged in.
16 ISCSI_ERR_INVALID_MGMT_REQ - invalid IPC MGMT request.
17 ISCSI_ERR_ISNS_UNAVAILABLE - iSNS service is not supported.
18 ISCSI_ERR_ISCSID_COMM_ERR - a read/write to iscsid failed.
19 ISCSI_ERR_FATAL_LOGIN - fatal iSCSI login error.
20 ISCSI_ERR_ISCSID_NOTCONN - could not connect to iscsid.
21 ISCSI_ERR_NO_OBJS_FOUND - no records/targets/sessions/portals found to execute
operation on.
22 ISCSI_ERR_SYSFS_LOOKUP - could not lookup object in sysfs.
23 ISCSI_ERR_HOST_NOT_FOUND - could not lookup host.
24 ISCSI_ERR_LOGIN_AUTH_FAILED - login failed due to authorization failure.
25 ISCSI_ERR_ISNS_QUERY - iSNS query failure.
26 ISCSI_ERR_ISNS_REG_FAILED - iSNS registration/deregistration failed.
27 ISCSI_ERR_OP_NOT_SUPP - operation not support
28 ISCSI_ERR_BUSY - device or resource in use
29 ISCSI_ERR_AGAIN - operation failed, but retrying later may succeed
30 ISCSI_ERR_UNKNOWN_DISCOVERY_TYPE - unknown discovery type
31 ISCSI_ERR_CHILD_TERMINATED - child process terminated
32 ISCSI_ERR_SESSION_NOT_CONNECTED - session likely not connected
EXAMPLES
Discover targets at a given IP address:
sh# iscsiadm --mode discoverydb --type sendtargets --portal 192.168.1.10 --discover
Login, must use a node record id found by the discovery:
sh# iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal
192.168.1.1:3260 --login
Logout:
sh# iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal
192.168.1.1:3260 --logout
List node records:
sh# iscsiadm --mode node
Display all data for a given node record:
sh# iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal
192.168.1.1:3260
List all sessions:
sh# iscsiadm --mode session
List all sessions in tree format:
sh# iscsiadm --mode session --print
FILES
/etc/iscsi/iscsid.conf
The configuration file read by iscsid and iscsiadm on startup.
/etc/iscsi/initiatorname.iscsi
The file containing the iSCSI InitiatorName and InitiatorAlias read by iscsid and
iscsiadm on startup.
/etc/iscsi/nodes/
This directory contains the nodes with their targets.
/etc/iscsi/send_targets
This directory contains the portals.
SEE ALSO
iscsid(8)
AUTHORS
Open-iSCSI project <http://www.open-iscsi.com/>
Alex Aizman <itn780@yahoo.com>
Dmitry Yusupov <dmitry_yus@yahoo.com>
Mar 2022 ISCSIADM(8)