Provided by: plc-utils_0.0.6+git20230504.1ba7d5a0-1_amd64 
NAME
int6k - Qualcomm Atheros INT6x00 Powerline Device Manager
SYNOPSIS
int6k [options] [device] [device] [...]
DESCRIPTION
This version of the Qualcomm Atheros Device Manager for Linux performs basic operations on
Atheros INT6x00 devices using the raw Ethernet protocol described in the Qualcomm Atheros
HomePlug AV Firmware Technical Reference Manual. It can be used to interrogate and
control devices or upgrade firmware if on-board NVRAM is present.
This program is part of the Qualcomm Atheros Powerline Toolkit. Is supports legacy
chipsets INT6000, INT6300 and INT6400. See program amptool for AR7400 and AR7450
chipsets. See program plctool for QCA6410, QCA7000 and QCA7420 chipsets. See the plc man
page for an overview and installation instructions.
OPTIONS
-a Read device attributes using VS_OP_ATTRIBUTES. Attributes are short strings and
integers that describe device hardware and firmware. They are concatenated to form
the output that is similar to option -r but derived differently.
-B action
Press the simple connect pushbutton using VS_PB_ENC. The action can be specified
by number 1, 2, 3 or 4 or by symbol "join", "leave", "status" or "reset",
respectively. Use 1 on both devices that are expected to join. Use 2 only on the
device that is expected to leave the network.
-C module
Commit (flash) downloaded modules to NVRAM using VS_MOD_NVM. The module can be
spedified by number 1, 2 or 3 or by symbol "nvm", "pib" or "both", repectively.
Module 3 is equivalent to option -F which writes the NVM and PIB together. You
cannot force flash NVRAM using this option. Use option -FF to force flash.
-d filename
Read Watchdog Report from the device and write it to the named file in binary
format using VS_WD_RPT. The report file can be sent to Qualcomm Atheros for
technical analysis. No assumptions are made based on filename and no filename
convetions are enforced; however, you should use a .log file extension to indicate
binary format.
-D xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx
Define the 16 octet Device Access Key (DAK) in hex format. The DAK is used by
option -J. It may also be set to "key1" or "key2" as explained in the KEYS
section.
-e Redirects stderr messages to stdout. By convention status and error messages are
printed on stderr while primary program output is printed on stdout. This option
prints all output on stdout in cases where this is desired.
-f Read device NVRAM parameters using VS_GET_NVM. An error will be reported when no
NVRAM is present. This option can be used to determine if NVRAM is large enough to
store the runtime firmware and parameter block.
-F[F] Write previously downloaded MAC and PIB to NVRAM using VS_MOD_NVM. Adding a second
F here or another -F anywhere on the command line will force-flash a blank or
corrupted NVRAM. Firmware loaded from NVRAM will treat force-flash as an error.
This option can be used to create factory settings but cannot be used to change
them once created. Subsequent use creates and updates operational settings that
can be erased using a factory reset. This option is executed after all others on
the command line, except for the -R option.
-i interface
Select the host Ethernet interface. All requests are sent via this host interface
and only reponses received via this host interface are recognized. The default
interface is eth1 because most people use eth0 as their principle network
connection; however, if environment string "PLC" is defined then it takes
precedence over the default interface. This option then takes precedence over
either default.
-I Read the device PIB header using VS_RD_MOD and print the firmware major revision
number, PIB minor revision number, Device Access Key (DAK), Network Membership Key
(NMK), MAC address and other information on stdout.
-J xx:xx:xx:xx:xx:xx
Set the Network Membership Key (NMK) on the remote device, specified by MAC, using
VS_SET_KEY. This option is similar to option -K but requires the remote device MAC
and DAK in addition to the NMK and local device MAC address. The NMK value is
defined using option -K unless you want to use the default value. The remote DAK
is defined using option -D unless you want to use the default value. Programming
remote device keys is complicated. It is often easier to connect the device
directly to the host and use the -K option.
-K xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx
Define the Network Membership Key (NMK) value used by options -M or -J. The
symbolic names "key1" and "key2" are recognized as described in the KEY section.
-l count
Define the number of times that the command will be repeated for each device
specified. Normally, you will repeat operations on one device only.
-m Read network membership information using VS_NW_INFO. This can be used to
determine network configuration.
-M Set the Network Membership Key (NMK) on the local device using VS_SET_KEY. The NMK
value is specified using the -K option unless you want to use the default value.
-n filename
Read firmware from the device SDRAM and write it to the named .nvm file using
multiple VS_RD_MOD messages. No assumptions are made based on filename and no
filename conventions are enforced. This option is performed before option -N when
both are specified.
-N filename
Read the named .nvm file and write it to the device using multiple VS_WR_MOD
messages. No assumptions are made based on filename and no filename conventions
are enforced; however, files having invalid .nvm format will be rejected. This
option is executed after -n when both are specified.
-p filename
Read parameters from the device SDRAM and write them to the named .pib file using
multiple VS_RD_MOD messages. No assumptions are made based on filename and no
filename convetions are enforced. This option is executed before option BP when
both are specified.
-P filename
Read the named .pib file and write it to the device using multiple VS_WR_MOD
messages. No assumptions are made based on filename and no filename conventions
are enforced; however, files having invalid .pib format will be rejected. This
option is executed after -p when both are specified.
-q Suppresses status messages on stderr.
-Q Quick flash. The program will not wait for a device to reset or the firmware to
restart after writing flash memory. This option is desirable with newer firmware
that writes flash memory in the background. It has no effect unless used with
option -F or -C.
-r Read device firmware and hardware revision using VS_SW_VER. Output is similar to
option -a but is derived differently.
-R Reset the device using VS_RS_DEV. This option is executed after all others on the
same command line.
-s Read device SDRAM configuration using VS_RD_CBLOCK.
-S filename
Read the named .cfg file and write it to the device using VS_SET_SDRAM. No
assumptions are made based on filename and no filename conventions are enforced;
however, files having an invalid .cfg file format will be rejected. Do not confuse
.cfg files with .config files. See chkcfg and config2cfg for more information on
SDRAM configuration file formats.
-t milliseconds
Read timeout in milliseconds. Values range from 0 through UINT_MAX. This is the
maximum time allowed for a response. The default is shown in brackets on the
program menu.
-T Restore factory defaults. This permanently erases all PIB changes made since the
device was last programmed with factory default settings. The device will
automatically reset and reboot.
-v Print additional information on stdout. In particular, this option dumps incoming
and outgoing packets which can be saved as text files for reference.
-w seconds
Defines the number of seconds to wait before repeating command line options. This
option has no effect unless option -l is also specified with a non-zero value.
-x Cause the program to exit on the first error instead of continuing with remaining
iterations, operations or devices. Normally, the program reports errors and moves
on to the next operation, iteration or device depending on the command line.
-?,--help
Print program help summary on stdout. This option takes precedence over other
options on the command line.
-?,--version
Print program version information on stdout. This option takes precedence over
other options on the command line. Use this option when sending screen dumps to
Atheros Technical Support so that they know exactly which version of the Linux
Toolkit you are using.
ARGUMENTS
device The Ethernet hardware address of some powerline device. More than one address may
be specified on the command line. If more than one address is specified then
operations are performed on each device in turn. The default address is local. as
explained in the DEVICES section.
KEYS
Passwords are variable length character strings that end-users can remember. Keys are
fixed length binary values created by encrypting passwords. There are two encryption
algorithms for HomePlugAV. One for DAKs and the other for NMKs. This means that a given
password will produce different keys depending on use. This program only deals with keys
because that is what powerline devices recognize. The passwords that generated the keys
are irrelevant here.
Encryption keys are tedious to type and prone to error. For convenience, symbolic names
have been assigned to common encryption keys and are recognized by options -D and -K.
key1 Key for encrypted password "HomePlugAV". This is
"689F074B8B0275A2710B0B5779AD1630" for option -D and
"50D3E4933F855B7040784DF815AA8DB7" for option -K.
key2 Key for encrypted password "HomePlugAV0123". This is
"F084B4E8F6069FF1300C9BDB812367FF" for option -D and
"B59319D7E8157BA001B018669CCEE30D" for option -K.
none Always "00000000000000000000000000000000".
DEVICES
Powerline devices use Ethernet hardware, or Media Access Control (MAC), addresses. Device
addresses are 12 hexadecimal digits (0123456789ABCDEFabcdef) in upper, lower or mixed
case. Individual octets may be separated by colons, for clarity, but not all octets need
to be seperated. For example, "00b052000001", "00:b0:52:00:00:01" and "00b052:000001" are
valid and equivalent.
These symbolic addresses are recognized by this program and may be used instead of the
actual address value.
all Equivalent to "broadcast", described next.
broadcast
The Ethernet broadcast address, FF:FF:FF:FF:FF:FF. All devices, whether local,
remote or foreign will respond to this address.
local The Atheros Local Management Address (LMA), 00:B0:52:00:00:01. Local Atheros
powerline devices recognize this address but remote and foreign powerline devices
do not. A remote device is any poserline device at the far end of the powerline.
A foreign device is a powerline device not manufactured by Atheros.
REFERENCES
See the Qualcomm Atheros HomePlug AV Firmware Technical Reference Manual for more
information.
DISCLAIMER
Atheros HomePlug AV Vendor Specific Management Message structure and content is
proprietary to Qualcomm Atheros, Ocala FL USA. Consequently, public information may not
be available. Qualcomm Atheros reserves the right to modify message structure or content
in future firmware releases without any obligation to notify or compensate users of this
program.
EXAMPLES
# int6k -n old.nvm -p old.pib -N new.nvm -P new.pib -F 01:23:45:67:89:AB
Performs 5 operations on one device. Uploads the firmware and PIB from the device and
writes them to files old.nvm and old.pib, respectively. Reads files new.nvm and new.pib
and downloads them as new firmware and PIB, respectively. Commits the downloaded firmware
and PIB to NVRAM. Operations are executed in the order just described regardless of the
order specified on the command line. If you want reading and writing to occur in a
different order then you must use two or more commands to accomplish tasks in the order
you want.
# int6k -N new.nvm 01:23:45:67:89:28
# int6k -P new.pib 01:23:45:67:89:28
# int6k -C 3 01:23:45:67:89:28
It is not neccessary to specify all operations on one command line. The three command
lines above do essentially the same thing as the command line shown in the previou
example. Notice that this example uses -C 3, instead of -F, as an alternate way to write
MAC and PIB to NVRAM. Specifying -C 1, instead, would write the .nvm file only.
Specifying, -C 2, instead, would write the .pib file only. The value 3 is the logical OR
of 1 and 2.
# int6k -N new.nvm -P new.pib -FF local
Downloads file new.nvm and file new.pib and force flashes the local device. Force
flashing only works on running firmware that has been downloaded and stated by the
Qualcomm Atheros Boot Loader. See int6kf to download, start firmware and perform a force
flash in one operation.
# int6k -MK key1
# int6k -M
These two commands are equivalent. They set the NMK on the local device to key1 as
descripted in the KEYS section. The first command resets the NMK on the local device with
-M then specifies the NMK as key1. The second command omits the key specification since
key1 is the program default NMK. One could, of course, type the encryption key.
SEE ALSO
plc(1), amptool(1), int6kf(1), int6khost(1), int6kid(1), int6krate(1), int6krule(1),
int6kstat(1), int6kwait(1), plctool(1)
CREDITS
Charles Maier
Nathaniel Houghton