Ubuntu Manpage: ipmi/lan.conf - IPMI LAN Interface config file

NAME

       ipmi/lan.conf - IPMI LAN Interface config file

SYNOPSIS

       /etc/ipmi/lan.conf

DESCRIPTION

       The ipmi_sim and ipmilan commands are configured using this configuration file.

CONFIGURATION ITEMS

       The following fields are used in many commands:

       boolean May be "true", "false", "on" or "off".

       priv An IPMI privilege level.  This may be "callback", "user", "operator", or "admin".

       auth An IPMI authorization type.  This may be "none" for no authentication, "straight" for
       straight,  in-the-clear  password  authentication,  "md2"  for  use  MD2  message   digest
       authentication, or "md5" for using MD5 message digest authentication.

FILE STRUCTURE

Blank lines and lines starting with `#' are ignored.

The following commands are allowed the configuration file:

name "name"
Set a name for the BMC. This will control other things, like the default value of
the ipmi_sim startup command file and the place where persistent data is stored.

user usernum enabled username password max-priv max-session
usernum specifies the user number for the user. Note that user number 0 is
invalid, and user number 1 is the special "anonymous" user, whose username is
ignored. This value may be up to 63, the maximum possible IPMI user. If you want
anonymous access, you must have a user number 1.

enabled is a boolean that specified whether the user is enabled or not.

username specifies the name of the user, specified as a name.

password specifies the password of the user, specified as a name.

max-priv specifies the maximum privilege level allowed for the user.

max.sessions specifies the maximum number of session the user may open.

startcmd "cmd"
specifies a command to execute when a power on is requested. This lets a virtual
machine be started that can then connect back to the simulator. The simulator does
management of the process here, and the power on state of the process depends on if
the process exists or not. If a poweroff is requested, if the process is connected
to a VM serial interface, a graceful shutdown is first requested. If the process
does not terminate in a specified amount of time, a SIGTERM is sent to the process.
The SIGTERM is sent immediately if there is no connection. If the process doesn't
go way in another specified amount of time, a SIGKILL is sent.

startnowtrue|false
If true, start the startcmd at the startup of the simulator. Otherwise wait until
a poweron is issued.

poweroff_wait seconds
specifies the amount of time to wait for the startcmd to do a graceful shutdown on
a powerdown request. The simulator will send a request to the target, wait this
amount of time, and then do a SIGTERM kill on the process. If this is zero, a
SIGTERM will not be done (nor will a SIGKILL). Note that if the simulator does not
have a connection to the VM, the graceful shutdown is skipped and a SIGTERM is done
immediately. Default time is 60 seconds.

kill_wait seconds
specifies the amount of time to wait for SIGTERM to kill the process. If the
process does not terminate in this period of time, send a SIGKILL kill. If this is
zero, don't send the SIGKILL. Default time is 20 seconds.

console address port
specifies that a console port be opened at the given address and port. You can
telnet to the console and execute emulation commands. Note that this is a pretty
huge security hole, it should only be used for debugging in a captive environment.

serial channel addr port [option [option [...]]]
channel specifies the channel number or type. This may be kcs, smic, or bt or it
may be 15. Currently, only the system interface channel (channel 15) is supported
for serial interfaces, if the others are specified it is channel 15 and the given
interface is reported in channel configuration commands.

addr specifies the IP address to listen on for connections.

port specifies the port to listen on for connections.

Valid options are:

codec name specifies which codec to use on the serial port. Valid options are:
TerminalMode, Direct, RadisysAscii, and VM. The first three are implementations of
IPMI serial interfaces on certain systems and might be used for simulations of that
system. The VM is probably the most interesting; it is designed to be used with a
virtual machine like qemu.

oem name specified implementation of some OEM custom commands and options on the
interface. Valid options oare PigeonPoint and Radisys.

attn c1[,c2[...]] specifies a list of characters, separated by commas, to use as
the attention character on the interface. Generally the default is correct. The
characters are specified as decimal, octal, or hex digits in C style.

ipmb addr specifies the IPMI address of the interface. The default, 0x20, is
usually correct, but when emulating ATCA systems this might be required.

sol device default_baud [history=size[,backupfile=filename]] [historyfru=frunum]

Allow a Serial Over LAN (SOL) connection to the given device. This will be over
interface 1 for the MC.

device is the full path to the device name. It can also be in the form
"tcp:address:port" or "telnet:address:port" to do connections over tcp (without or
with telnet processing). This is useful for providing SOL access to qemu ports.

default_baud sets the initial default baud rate to use. This is overriden by the
persistent SOL settings.

history creates a history device on SOL interface 2. The size is the size of the
buffer. Data from the device is stored in the history buffer all the time.
Connecting to SOL interface 2 will cause the full history buffer to be dumped. If
backupfile is specified, then the history is made persistent. However, it is only
stored when a catchable signal or normal shutdown is done, so a poweroff or fatal
signal will cause the data to be lost.

historyfru makes the history available via the given FRU number on the MC.

Note that if the connection fails to come up, the simulator will continue to try to
connect. This way you can fix UDP serial ports or qemu sessions and it will
automatically reconnect.

loadlib "module" ["options"]

Load the given shared object into the program.

module is the full path to the module. It must be in quotes.

options is an optional string in quotes that passes options to the module. The
contents of the string are not specified, the module defines that.

The module may have a number of functions that are called:

ipmi_sim_module_print_version(sys_data_t *sys, char *options) is called when
ipmi_sim is started with the version print option. This way the versions of all
loaded modules may be printed. The module should print it's version. You must
provide this function.

ipmi_sim_module_init(sys_data_t *sys, char *options) is called after the
configuration file is read and before any other initialization is done. The module
should do most of its initialization here. You must provide this function.

ipmi_sim_module_post_init(sys_data_t *sys) is called after ipmi_sim has finished
initializing. This function is optional.

sys parameter is used for most functions interfacing to the main ipmi_sim code, like
logging, timers, and a few of the MC calls. The contents are opaque to the module.

startlan channel
Starts a LAN configuration area. This specifies the settings for a LAN connection
using the given channel. This may be specified more than once in a file to support
multiple LAN connections. Commands following this, up to endlan, are LAN-specific
commands listed below. channel specifies the channel to set the LAN configuration
for.

LAN CONFIGURATION COMMANDS

The following commands are only valid inside a startlen area.

addr IP-address [UDP-port]
IP-address specifies the IP address to use for an IP port. Up to 4 addresses may be
specified. If no address is specified, it defaults to one port at 0.0.0.0 (for
every address on the machine) at port 623.

UDP-port specifies an optional port to listen on. It defaults to 623 (the standard
port).

PEF_alerting boolean
Turn PEF alerting on or off (not currently supported).

per_msg_auth boolean
Turn per-message authentication on or off.

priv_limit priv
The maximum privilege allowed on this interface.

allowed_auths_callback [auth [auth [...]]]
auth specifies allowed authorization levels for the callback privilege level. Only
the levels specified on this line are allowed for the authorization level. If this
line is not present, callback authorization cannot be used.

allowed_auths_user [auth [auth [...]]]
auth specifies allowed authorization levels for the user privilege level. Only the
levels specified on this line are allowed for the authorization level. If this
line is not present, user authorization cannot be used.

allowed_auths_operator [auth [auth [...]]]
auth specifies allowed authorization levels for the operator privilege level. Only
the levels specified on this line are allowed for the authorization level. If this
line is not present, operator authorization cannot be used.

allowed_auths_admin [auth [auth [...]]]
auth specifies allowed authorization levels for the admin privilege level. Only
the levels specified on this line are allowed for the authorization level. If this
line is not present, user authorization cannot be used.

guid name
Allows the 16-byte GUID for the IPMI LAN connection to be specified. If this is
not specified, then the GUID command is not supported.

FILES

       /etc/ipmi_lan.conf

KNOWN PROBLEMS

       IPMI is unnecessarily complicated.

AUTHOR

       Corey Minyard <cminyard@mvista.com>