Provided by: mdadm_4.2+20230508-7ubuntu1_amd64 
NAME
mdadm - manage MD devices aka Linux Software RAID
SYNOPSIS
mdadm [mode] <raiddevice> [options] <component-devices>
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows
multiple devices (typically disk drives or partitions thereof) to be combined into a
single device to hold (for example) a single filesystem. Some RAID levels include
redundancy and so can survive some degree of device failure.
Linux Software RAID devices are implemented through the md (Multiple Devices) device
driver.
Currently, Linux supports LINEAR md devices, RAID0 (striping), RAID1 (mirroring), RAID4,
RAID5, RAID6, RAID10, MULTIPATH, FAULTY, and CONTAINER.
MULTIPATH is not a Software RAID mechanism, but does involve multiple devices: each device
is a path to one common physical storage device. New installations should not use
md/multipath as it is not well supported and has no ongoing development. Use the Device
Mapper based multipath-tools instead.
FAULTY is also not true RAID, and it only involves one device. It provides a layer over a
true device that can be used to inject faults.
CONTAINER is different again. A CONTAINER is a collection of devices that are managed as
a set. This is similar to the set of devices connected to a hardware RAID controller.
The set of devices may contain a number of different RAID arrays each utilising some (or
all) of the blocks from a number of the devices in the set. For example, two devices in a
5-device set might form a RAID1 using the whole devices. The remaining three might have a
RAID5 over the first half of each device, and a RAID0 over the second half.
With a CONTAINER, there is one set of metadata that describes all of the arrays in the
container. So when mdadm creates a CONTAINER device, the device just represents the
metadata. Other normal arrays (RAID1 etc) can be created inside the container.
MODES
mdadm has several major modes of operation:
Assemble
Assemble the components of a previously created array into an active array.
Components can be explicitly given or can be searched for. mdadm checks that the
components do form a bona fide array, and can, on request, fiddle superblock
information so as to assemble a faulty array.
Build Build an array that doesn't have per-device metadata (superblocks). For these
sorts of arrays, mdadm cannot differentiate between initial creation and subsequent
assembly of an array. It also cannot perform any checks that appropriate
components have been requested. Because of this, the Build mode should only be
used together with a complete understanding of what you are doing.
Create Create a new array with per-device metadata (superblocks). Appropriate metadata is
written to each device, and then the array comprising those devices is activated.
A 'resync' process is started to make sure that the array is consistent (e.g. both
sides of a mirror contain the same data) but the content of the device is left
otherwise untouched. The array can be used as soon as it has been created. There
is no need to wait for the initial resync to finish.
Follow or Monitor
Monitor one or more md devices and act on any state changes. This is only
meaningful for RAID1, 4, 5, 6, 10 or multipath arrays, as only these have
interesting state. RAID0 or Linear never have missing, spare, or failed drives, so
there is nothing to monitor.
Grow Grow (or shrink) an array, or otherwise reshape it in some way. Currently
supported growth options including changing the active size of component devices
and changing the number of active devices in Linear and RAID levels 0/1/4/5/6,
changing the RAID level between 0, 1, 5, and 6, and between 0 and 10, changing the
chunk size and layout for RAID 0,4,5,6,10 as well as adding or removing a write-
intent bitmap and changing the array's consistency policy.
Incremental Assembly
Add a single device to an appropriate array. If the addition of the device makes
the array runnable, the array will be started. This provides a convenient
interface to a hot-plug system. As each device is detected, mdadm has a chance to
include it in some array as appropriate. Optionally, when the --fail flag is
passed in we will remove the device from any active array instead of adding it.
If a CONTAINER is passed to mdadm in this mode, then any arrays within that
container will be assembled and started.
Manage This is for doing things to specific components of an array such as adding new
spares and removing faulty devices.
Misc This is an 'everything else' mode that supports operations on active arrays,
operations on component devices such as erasing old superblocks, and information-
gathering operations.
Auto-detect
This mode does not act on a specific device or array, but rather it requests the
Linux Kernel to activate any auto-detected arrays.
OPTIONS
Options for selecting a mode are:
-A, --assemble
Assemble a pre-existing array.
-B, --build
Build a legacy array without superblocks.
-C, --create
Create a new array.
-F, --follow, --monitor
Select Monitor mode.
-G, --grow
Change the size or shape of an active array.
-I, --incremental
Add/remove a single device to/from an appropriate array, and possibly start the
array.
--auto-detect
Request that the kernel starts any auto-detected arrays. This can only work if md
is compiled into the kernel — not if it is a module. Arrays can be auto-detected
by the kernel if all the components are in primary MS-DOS partitions with partition
type FD, and all use v0.90 metadata. In-kernel autodetect is not recommended for
new installations. Using mdadm to detect and assemble arrays — possibly in an
initrd — is substantially more flexible and should be preferred.
If a device is given before any options, or if the first option is one of --add, --re-add,
--add-spare, --fail, --remove, or --replace, then the MANAGE mode is assumed. Anything
other than these will cause the Misc mode to be assumed.
Options that are not mode-specific are:
-h, --help
Display a general help message or, after one of the above options, a mode-specific
help message.
--help-options
Display more detailed help about command-line parsing and some commonly used
options.
-V, --version
Print version information for mdadm.
-v, --verbose
Be more verbose about what is happening. This can be used twice to be extra-
verbose. The extra verbosity currently only affects --detail --scan and --examine
--scan.
-q, --quiet
Avoid printing purely informative messages. With this, mdadm will be silent unless
there is something really important to report.
-f, --force
Be more forceful about certain operations. See the various modes for the exact
meaning of this option in different contexts.
-c, --config=
Specify the config file or directory. If not specified, the default config file
and default conf.d directory will be used. See mdadm.conf(5) for more details.
If the config file given is partitions then nothing will be read, but mdadm will
act as though the config file contained exactly
DEVICE partitions containers
and will read /proc/partitions to find a list of devices to scan, and /proc/mdstat
to find a list of containers to examine. If the word none is given for the config
file, then mdadm will act as though the config file were empty.
If the name given is of a directory, then mdadm will collect all the files
contained in the directory with a name ending in .conf, sort them lexically, and
process all of those files as config files.
-s, --scan
Scan config file or /proc/mdstat for missing information. In general, this option
gives mdadm permission to get any missing information (like component devices,
array devices, array identities, and alert destination) from the configuration file
(see previous option); one exception is MISC mode when using --detail or --stop, in
which case --scan says to get a list of array devices from /proc/mdstat.
-e, --metadata=
Declare the style of RAID metadata (superblock) to be used. The default is 1.2 for
--create, and to guess for other operations. The default can be overridden by
setting the metadata value for the CREATE keyword in mdadm.conf.
Options are:
0, 0.90
Use the original 0.90 format superblock. This format limits arrays to 28
component devices and limits component devices of levels 1 and greater to 2
terabytes. It is also possible for there to be confusion about whether the
superblock applies to a whole device or just the last partition, if that
partition starts on a 64K boundary.
1, 1.0, 1.1, 1.2 default
Use the new version-1 format superblock. This has fewer restrictions. It
can easily be moved between hosts with different endian-ness, and a recovery
operation can be checkpointed and restarted. The different sub-versions
store the superblock at different locations on the device, either at the end
(for 1.0), at the start (for 1.1) or 4K from the start (for 1.2). "1" is
equivalent to "1.2" (the commonly preferred 1.x format). "default" is
equivalent to "1.2".
ddf Use the "Industry Standard" DDF (Disk Data Format) format defined by SNIA.
When creating a DDF array a CONTAINER will be created, and normal arrays can
be created in that container.
imsm Use the Intel(R) Matrix Storage Manager metadata format. This creates a
CONTAINER which is managed in a similar manner to DDF, and is supported by
an option-rom on some platforms:
https://www.intel.com/content/www/us/en/support/products/122484/memory-and-
storage/ssd-software/intel-virtual-raid-on-cpu-intel-vroc.html
--homehost=
This will override any HOMEHOST setting in the config file and provides the
identity of the host which should be considered the home for any arrays.
When creating an array, the homehost will be recorded in the metadata. For
version-1 superblocks, it will be prefixed to the array name. For version-0.90
superblocks, part of the SHA1 hash of the hostname will be stored in the latter
half of the UUID.
When reporting information about an array, any array which is tagged for the given
homehost will be reported as such.
When using Auto-Assemble, only arrays tagged for the given homehost will be allowed
to use 'local' names (i.e. not ending in '_' followed by a digit string). See
below under Auto-Assembly.
The special name "any" can be used as a wild card. If an array is created with
--homehost=any then the name "any" will be stored in the array and it can be
assembled in the same way on any host. If an array is assembled with this option,
then the homehost recorded on the array will be ignored.
--prefer=
When mdadm needs to print the name for a device it normally finds the name in /dev
which refers to the device and is the shortest. When a path component is given
with --prefer mdadm will prefer a longer name if it contains that component. For
example --prefer=by-uuid will prefer a name in a subdirectory of /dev called by-
uuid.
This functionality is currently only provided by --detail and --monitor.
--home-cluster=
specifies the cluster name for the md device. The md device can be assembled only
on the cluster which matches the name specified. If this option is not provided,
mdadm tries to detect the cluster name automatically.
For create, build, or grow:
-n, --raid-devices=
Specify the number of active devices in the array. This, plus the number of spare
devices (see below) must equal the number of component-devices (including "missing"
devices) that are listed on the command line for --create. Setting a value of 1 is
probably a mistake and so requires that --force be specified first. A value of 1
will then be allowed for linear, multipath, RAID0 and RAID1. It is never allowed
for RAID4, RAID5 or RAID6.
This number can only be changed using --grow for RAID1, RAID4, RAID5 and RAID6
arrays, and only on kernels which provide the necessary support.
-x, --spare-devices=
Specify the number of spare (eXtra) devices in the initial array. Spares can also
be added and removed later. The number of component devices listed on the command
line must equal the number of RAID devices plus the number of spare devices.
-z, --size=
Amount (in Kilobytes) of space to use from each drive in RAID levels 1/4/5/6/10 and
for RAID 0 on external metadata. This must be a multiple of the chunk size, and
must leave about 128Kb of space at the end of the drive for the RAID superblock.
When specified as ¸max¸ (as it often is) the smallest drive (or partition) sets the
size. In that case, a warning will follow if the drives, as a group, have sizes
that differ by more than one percent.
A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes, Megabytes,
Gigabytes or Terabytes respectively.
Sometimes a replacement drive can be a little smaller than the original drives
though this should be minimised by IDEMA standards. Such a replacement drive will
be rejected by md. To guard against this it can be useful to set the initial size
slightly smaller than the smaller device with the aim that it will still be larger
than any replacement.
This option can be used with --create for determining the initial size of an array.
For external metadata, it can be used on a volume, but not on a container itself.
Setting the initial size of RAID 0 array is only valid for external metadata.
This value can be set with --grow for RAID level 1/4/5/6/10 though DDF arrays may
not be able to support this. RAID 0 array size cannot be changed. If the array
was created with a size smaller than the currently active drives, the extra space
can be accessed using --grow. The size can be given as max which means to choose
the largest size that fits on all current drives.
Before reducing the size of the array (with --grow --size=) you should make sure
that space isn't needed. If the device holds a filesystem, you would need to
resize the filesystem to use less space.
After reducing the array size you should check that the data stored in the device
is still available. If the device holds a filesystem, then an 'fsck' of the
filesystem is a minimum requirement. If there are problems the array can be made
bigger again with no loss with another --grow --size= command.
-Z, --array-size=
This is only meaningful with --grow and its effect is not persistent: when the
array is stopped and restarted the default array size will be restored.
Setting the array-size causes the array to appear smaller to programs that access
the data. This is particularly needed before reshaping an array so that it will be
smaller. As the reshape is not reversible, but setting the size with --array-size
is, it is required that the array size is reduced as appropriate before the number
of devices in the array is reduced.
Before reducing the size of the array you should make sure that space isn't needed.
If the device holds a filesystem, you would need to resize the filesystem to use
less space.
After reducing the array size you should check that the data stored in the device
is still available. If the device holds a filesystem, then an 'fsck' of the
filesystem is a minimum requirement. If there are problems the array can be made
bigger again with no loss with another --grow --array-size= command.
A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes, Megabytes,
Gigabytes or Terabytes respectively. A value of max restores the apparent size of
the array to be whatever the real amount of available space is.
Clustered arrays do not support this parameter yet.
-c, --chunk=
Specify chunk size in kilobytes. The default when creating an array is 512KB. To
ensure compatibility with earlier versions, the default when building an array with
no persistent metadata is 64KB. This is only meaningful for RAID0, RAID4, RAID5,
RAID6, and RAID10.
RAID4, RAID5, RAID6, and RAID10 require the chunk size to be a power of 2, with
minimal chunk size being 4KB.
A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes, Megabytes,
Gigabytes or Terabytes respectively.
--rounding=
Specify the rounding factor for a Linear array. The size of each component will be
rounded down to a multiple of this size. This is a synonym for --chunk but
highlights the different meaning for Linear as compared to other RAID levels. The
default is 64K if a kernel earlier than 2.6.16 is in use, and is 0K (i.e. no
rounding) in later kernels.
-l, --level=
Set RAID level. When used with --create, options are: linear, raid0, 0, stripe,
raid1, 1, mirror, raid4, 4, raid5, 5, raid6, 6, raid10, 10, multipath, mp, faulty,
container. Obviously some of these are synonymous.
When a CONTAINER metadata type is requested, only the container level is permitted,
and it does not need to be explicitly given.
When used with --build, only linear, stripe, raid0, 0, raid1, multipath, mp, and
faulty are valid.
Can be used with --grow to change the RAID level in some cases. See LEVEL CHANGES
below.
-p, --layout=
This option configures the fine details of data layout for RAID5, RAID6, and RAID10
arrays, and controls the failure modes for faulty. It can also be used for working
around a kernel bug with RAID0, but generally doesn't need to be used explicitly.
The layout of the RAID5 parity block can be one of left-asymmetric, left-symmetric,
right-asymmetric, right-symmetric, la, ra, ls, rs. The default is left-symmetric.
It is also possible to cause RAID5 to use a RAID4-like layout by choosing
parity-first, or parity-last.
Finally for RAID5 there are DDF-compatible layouts, ddf-zero-restart,
ddf-N-restart, and ddf-N-continue.
These same layouts are available for RAID6. There are also 4 layouts that will
provide an intermediate stage for converting between RAID5 and RAID6. These
provide a layout which is identical to the corresponding RAID5 layout on the first
N-1 devices, and has the 'Q' syndrome (the second 'parity' block used by RAID6) on
the last device. These layouts are: left-symmetric-6, right-symmetric-6,
left-asymmetric-6, right-asymmetric-6, and parity-first-6.
When setting the failure mode for level faulty, the options are: write-transient,
wt, read-transient, rt, write-persistent, wp, read-persistent, rp, write-all,
read-fixable, rf, clear, flush, none.
Each failure mode can be followed by a number, which is used as a period between
fault generation. Without a number, the fault is generated once on the first
relevant request. With a number, the fault will be generated after that many
requests, and will continue to be generated every time the period elapses.
Multiple failure modes can be current simultaneously by using the --grow option to
set subsequent failure modes.
"clear" or "none" will remove any pending or periodic failure modes, and "flush"
will clear any persistent faults.
The layout options for RAID10 are one of 'n', 'o' or 'f' followed by a small number
signifying the number of copies of each datablock. The default is 'n2'. The
supported options are:
'n' signals 'near' copies. Multiple copies of one data block are at similar
offsets in different devices.
'o' signals 'offset' copies. Rather than the chunks being duplicated within a
stripe, whole stripes are duplicated but are rotated by one device so duplicate
blocks are on different devices. Thus subsequent copies of a block are in the next
drive, and are one chunk further down.
'f' signals 'far' copies (multiple copies have very different offsets). See md(4)
for more detail about 'near', 'offset', and 'far'.
As for the number of copies of each data block, 2 is normal, 3 can be useful. This
number can be at most equal to the number of devices in the array. It does not
need to divide evenly into that number (e.g. it is perfectly legal to have an 'n2'
layout for an array with an odd number of devices).
A bug introduced in Linux 3.14 means that RAID0 arrays with devices of differing
sizes started using a different layout. This could lead to data corruption. Since
Linux 5.4 (and various stable releases that received backports), the kernel will
not accept such an array unless a layout is explicitly set. It can be set to
'original' or 'alternate'. When creating a new array, mdadm will select 'original'
by default, so the layout does not normally need to be set. An array created for
either 'original' or 'alternate' will not be recognized by an (unpatched) kernel
prior to 5.4. To create a RAID0 array with devices of differing sizes that can be
used on an older kernel, you can set the layout to 'dangerous'. This will use
whichever layout the running kernel supports, so the data on the array may become
corrupt when changing kernel from pre-3.14 to a later kernel.
When an array is converted between RAID5 and RAID6 an intermediate RAID6 layout is
used in which the second parity block (Q) is always on the last device. To convert
a RAID5 to RAID6 and leave it in this new layout (which does not require re-
striping) use --layout=preserve. This will try to avoid any restriping.
The converse of this is --layout=normalise which will change a non-standard RAID6
layout into a more standard arrangement.
--parity=
same as --layout (thus explaining the p of -p).
-b, --bitmap=
Specify a file to store a write-intent bitmap in. The file should not exist unless
--force is also given. The same file should be provided when assembling the array.
If the word internal is given, then the bitmap is stored with the metadata on the
array, and so is replicated on all devices. If the word none is given with --grow
mode, then any bitmap that is present is removed. If the word clustered is given,
the array is created for a clustered environment. One bitmap is created for each
node as defined by the --nodes parameter and are stored internally.
To help catch typing errors, the filename must contain at least one slash ('/') if
it is a real file (not 'internal' or 'none').
Note: external bitmaps are only known to work on ext2 and ext3. Storing bitmap
files on other filesystems may result in serious problems.
When creating an array on devices which are 100G or larger, mdadm automatically
adds an internal bitmap as it will usually be beneficial. This can be suppressed
with --bitmap=none or by selecting a different consistency policy with
--consistency-policy.
--bitmap-chunk=
Set the chunk size of the bitmap. Each bit corresponds to that many Kilobytes of
storage. When using a file-based bitmap, the default is to use the smallest size
that is at least 4 and requires no more than 2^21 chunks. When using an internal
bitmap, the chunk size defaults to 64Meg, or larger if necessary to fit the bitmap
into the available space.
A suffix of 'K', 'M', 'G' or 'T' can be given to indicate Kilobytes, Megabytes,
Gigabytes or Terabytes respectively.
-W, --write-mostly
subsequent devices listed in a --build, --create, or --add command will be flagged
as 'write-mostly'. This is valid for RAID1 only and means that the 'md' driver
will avoid reading from these devices if at all possible. This can be useful if
mirroring over a slow link.
--write-behind=
Specify that write-behind mode should be enabled (valid for RAID1 only). If an
argument is specified, it will set the maximum number of outstanding writes
allowed. The default value is 256. A write-intent bitmap is required in order to
use write-behind mode, and write-behind is only attempted on drives marked as
write-mostly.
--failfast
subsequent devices listed in a --create or --add command will be flagged as
'failfast'. This is valid for RAID1 and RAID10 only. IO requests to these devices
will be encouraged to fail quickly rather than cause long delays due to error
handling. Also no attempt is made to repair a read error on these devices.
If an array becomes degraded so that the 'failfast' device is the only usable
device, the 'failfast' flag will then be ignored and extended delays will be
preferred to complete failure.
The 'failfast' flag is appropriate for storage arrays which have a low probability
of true failure, but which may sometimes cause unacceptable delays due to internal
maintenance functions.
--assume-clean
Tell mdadm that the array pre-existed and is known to be clean. It can be useful
when trying to recover from a major failure as you can be sure that no data will be
affected unless you actually write to the array. It can also be used when creating
a RAID1 or RAID10 if you want to avoid the initial resync, however this practice —
while normally safe — is not recommended. Use this only if you really know what
you are doing.
When the devices that will be part of a new array were filled with zeros before
creation the operator knows the array is actually clean. If that is the case, such
as after running badblocks, this argument can be used to tell mdadm the facts the
operator knows.
When an array is resized to a larger size with --grow --size= the new space is
normally resynced in that same way that the whole array is resynced at creation.
From Linux version 3.0, --assume-clean can be used with that command to avoid the
automatic resync.
--write-zeroes
When creating an array, send write zeroes requests to all the block devices. This
should zero the data area on all disks such that the initial sync is not necessary
and, if successfull, will behave as if --assume-clean was specified.
This is intended for use with devices that have hardware offload for zeroing, but
despite this zeroing can still take several minutes for large disks. Thus a
message is printed before and after zeroing and each disk is zeroed in parallel
with the others.
This is only meaningful with --create.
--backup-file=
This is needed when --grow is used to increase the number of raid devices in a
RAID5 or RAID6 if there are no spare devices available, or to shrink, change RAID
level or layout. See the GROW MODE section below on RAID-DEVICES CHANGES. The
file must be stored on a separate device, not on the RAID array being reshaped.
--data-offset=
Arrays with 1.x metadata can leave a gap between the start of the device and the
start of array data. This gap can be used for various metadata. The start of data
is known as the data-offset. Normally an appropriate data offset is computed
automatically. However it can be useful to set it explicitly such as when re-
creating an array which was originally created using a different version of mdadm
which computed a different offset.
Setting the offset explicitly over-rides the default. The value given is in
Kilobytes unless a suffix of 'K', 'M', 'G' or 'T' is used to explicitly indicate
Kilobytes, Megabytes, Gigabytes or Terabytes respectively.
Since Linux 3.4, --data-offset can also be used with --grow for some RAID levels
(initially on RAID10). This allows the data-offset to be changed as part of the
reshape process. When the data offset is changed, no backup file is required as
the difference in offsets is used to provide the same functionality.
When the new offset is earlier than the old offset, the number of devices in the
array cannot shrink. When it is after the old offset, the number of devices in the
array cannot increase.
When creating an array, --data-offset can be specified as variable. In the case
each member device is expected to have an offset appended to the name, separated by
a colon. This makes it possible to recreate exactly an array which has varying
data offsets (as can happen when different versions of mdadm are used to add
different devices).
--continue
This option is complementary to the --freeze-reshape option for assembly. It is
needed when --grow operation is interrupted and it is not restarted automatically
due to --freeze-reshape usage during array assembly. This option is used together
with -G , ( --grow ) command and device for a pending reshape to be continued. All
parameters required for reshape continuation will be read from array metadata. If
initial --grow command had required --backup-file= option to be set, continuation
option will require to have exactly the same backup file given as well.
Any other parameter passed together with --continue option will be ignored.
-N, --name=
Set a name for the array. This is currently only effective when creating an array
with a version-1 superblock, or an array in a DDF container. The name is a simple
textual string that can be used to identify array components when assembling. If
name is needed but not specified, it is taken from the basename of the device that
is being created. e.g. when creating /dev/md/home the name will default to home.
(Does not work in Grow mode.)
-R, --run
Insist that mdadm run the array, even if some of the components appear to be active
in another array or filesystem. Normally mdadm will ask for confirmation before
including such components in an array. This option causes that question to be
suppressed.
-f, --force
Insist that mdadm accept the geometry and layout specified without question.
Normally mdadm will not allow the creation of an array with only one device, and
will try to create a RAID5 array with one missing drive (as this makes the initial
resync work faster). With --force, mdadm will not try to be so clever.
-o, --readonly
Start the array read only rather than read-write as normal. No writes will be
allowed to the array, and no resync, recovery, or reshape will be started. It works
with Create, Assemble, Manage and Misc mode.
-a, --auto{=yes,md,mdp,part,p}{NN}
Instruct mdadm how to create the device file if needed, possibly allocating an
unused minor number. "md" causes a non-partitionable array to be used (though
since Linux 2.6.28, these array devices are in fact partitionable). "mdp", "part"
or "p" causes a partitionable array (2.6 and later) to be used. "yes" requires the
named md device to have a 'standard' format, and the type and minor number will be
determined from this. With mdadm 3.0, device creation is normally left up to udev
so this option is unlikely to be needed. See DEVICE NAMES below.
The argument can also come immediately after "-a". e.g. "-ap".
If --auto is not given on the command line or in the config file, then the default
will be --auto=yes.
If --scan is also given, then any auto= entries in the config file will override
the --auto instruction given on the command line.
For partitionable arrays, mdadm will create the device file for the whole array and
for the first 4 partitions. A different number of partitions can be specified at
the end of this option (e.g. --auto=p7). If the device name ends with a digit,
the partition names add a 'p', and a number, e.g. /dev/md/home1p3. If there is no
trailing digit, then the partition names just have a number added, e.g.
/dev/md/scratch3.
If the md device name is in a 'standard' format as described in DEVICE NAMES, then
it will be created, if necessary, with the appropriate device number based on that
name. If the device name is not in one of these formats, then an unused device
number will be allocated. The device number will be considered unused if there is
no active array for that number, and there is no entry in /dev for that number and
with a non-standard name. Names that are not in 'standard' format are only allowed
in "/dev/md/".
This is meaningful with --create or --build.
-a, --add
This option can be used in Grow mode in two cases.
If the target array is a Linear array, then --add can be used to add one or more
devices to the array. They are simply catenated on to the end of the array. Once
added, the devices cannot be removed.
If the --raid-disks option is being used to increase the number of devices in an
array, then --add can be used to add some extra devices to be included in the
array. In most cases this is not needed as the extra devices can be added as
spares first, and then the number of raid disks can be changed. However, for RAID0
it is not possible to add spares. So to increase the number of devices in a RAID0,
it is necessary to set the new number of devices, and to add the new devices, in
the same command.
--nodes
Only works when the array is created for a clustered environment. It specifies the
maximum number of nodes in the cluster that will use this device simultaneously. If
not specified, this defaults to 4.
--write-journal
Specify journal device for the RAID-4/5/6 array. The journal device should be an
SSD with a reasonable lifetime.
-k, --consistency-policy=
Specify how the array maintains consistency in the case of an unexpected shutdown.
Only relevant for RAID levels with redundancy. Currently supported options are:
resync Full resync is performed and all redundancy is regenerated when the array is
started after an unclean shutdown.
bitmap Resync assisted by a write-intent bitmap. Implicitly selected when using
--bitmap.
journal
For RAID levels 4/5/6, the journal device is used to log transactions and
replay after an unclean shutdown. Implicitly selected when using
--write-journal.
ppl For RAID5 only, Partial Parity Log is used to close the write hole and
eliminate resync. PPL is stored in the metadata region of RAID member
drives, no additional journal drive is needed.
Can be used with --grow to change the consistency policy of an active array in some
cases. See CONSISTENCY POLICY CHANGES below.
For assemble:
-u, --uuid=
uuid of array to assemble. Devices which don't have this uuid are excluded
-m, --super-minor=
Minor number of device that array was created for. Devices which don't have this
minor number are excluded. If you create an array as /dev/md1, then all
superblocks will contain the minor number 1, even if the array is later assembled
as /dev/md2.
Giving the literal word "dev" for --super-minor will cause mdadm to use the minor
number of the md device that is being assembled. e.g. when assembling /dev/md0,
--super-minor=dev will look for super blocks with a minor number of 0.
--super-minor is only relevant for v0.90 metadata, and should not normally be used.
Using --uuid is much safer.
-N, --name=
Specify the name of the array to assemble. This must be the name that was
specified when creating the array. It must either match the name stored in the
superblock exactly, or it must match with the current homehost prefixed to the
start of the given name.
-f, --force
Assemble the array even if the metadata on some devices appears to be out-of-date.
If mdadm cannot find enough working devices to start the array, but can find some
devices that are recorded as having failed, then it will mark those devices as
working so that the array can be started. This works only for native. For external
metadata it allows one to start dirty degraded RAID 4, 5, 6. An array which
requires --force to be started may contain data corruption. Use it carefully.
-R, --run
Attempt to start the array even if fewer drives were given than were present last
time the array was active. Normally if not all the expected drives are found and
--scan is not used, then the array will be assembled but not started. With --run
an attempt will be made to start it anyway.
--no-degraded
This is the reverse of --run in that it inhibits the startup of array unless all
expected drives are present. This is only needed with --scan, and can be used if
the physical connections to devices are not as reliable as you would like.
-a, --auto{=no,yes,md,mdp,part}
See this option under Create and Build options.
-b, --bitmap=
Specify the bitmap file that was given when the array was created. If an array has
an internal bitmap, there is no need to specify this when assembling the array.
--backup-file=
If --backup-file was used while reshaping an array (e.g. changing number of devices
or chunk size) and the system crashed during the critical section, then the same
--backup-file must be presented to --assemble to allow possibly corrupted data to
be restored, and the reshape to be completed.
--invalid-backup
If the file needed for the above option is not available for any reason an empty
file can be given together with this option to indicate that the backup file is
invalid. In this case the data that was being rearranged at the time of the crash
could be irrecoverably lost, but the rest of the array may still be recoverable.
This option should only be used as a last resort if there is no way to recover the
backup file.
-U, --update=
Update the superblock on each device while assembling the array. The argument
given to this flag can be one of sparc2.2, summaries, uuid, name, nodes, homehost,
home-cluster, resync, byteorder, devicesize, no-bitmap, bbl, no-bbl, ppl, no-ppl,
layout-original, layout-alternate, layout-unspecified, metadata, or super-minor.
The sparc2.2 option will adjust the superblock of an array what was created on a
Sparc machine running a patched 2.2 Linux kernel. This kernel got the alignment of
part of the superblock wrong. You can use the --examine --sparc2.2 option to mdadm
to see what effect this would have.
The super-minor option will update the preferred minor field on each superblock to
match the minor number of the array being assembled. This can be useful if
--examine reports a different "Preferred Minor" to --detail. In some cases this
update will be performed automatically by the kernel driver. In particular, the
update happens automatically at the first write to an array with redundancy (RAID
level 1 or greater) on a 2.6 (or later) kernel.
The uuid option will change the uuid of the array. If a UUID is given with the
--uuid option that UUID will be used as a new UUID and will NOT be used to help
identify the devices in the array. If no --uuid is given, a random UUID is chosen.
The name option will change the name of the array as stored in the superblock.
This is only supported for version-1 superblocks.
The nodes option will change the nodes of the array as stored in the bitmap
superblock. This option only works for a clustered environment.
The homehost option will change the homehost as recorded in the superblock. For
version-0 superblocks, this is the same as updating the UUID. For version-1
superblocks, this involves updating the name.
The home-cluster option will change the cluster name as recorded in the superblock
and bitmap. This option only works for a clustered environment.
The resync option will cause the array to be marked dirty meaning that any
redundancy in the array (e.g. parity for RAID5, copies for RAID1) may be incorrect.
This will cause the RAID system to perform a "resync" pass to make sure that all
redundant information is correct.
The byteorder option allows arrays to be moved between machines with different
byte-order, such as from a big-endian machine like a Sparc or some MIPS machines,
to a little-endian x86_64 machine. When assembling such an array for the first
time after a move, giving --update=byteorder will cause mdadm to expect superblocks
to have their byteorder reversed, and will correct that order before assembling the
array. This is only valid with original (Version 0.90) superblocks.
The summaries option will correct the summaries in the superblock. That is the
counts of total, working, active, failed, and spare devices.
The devicesize option will rarely be of use. It applies to version 1.1 and 1.2
metadata only (where the metadata is at the start of the device) and is only useful
when the component device has changed size (typically become larger). The version
1 metadata records the amount of the device that can be used to store data, so if a
device in a version 1.1 or 1.2 array becomes larger, the metadata will still be
visible, but the extra space will not. In this case it might be useful to assemble
the array with --update=devicesize. This will cause mdadm to determine the maximum
usable amount of space on each device and update the relevant field in the
metadata.
The metadata option only works on v0.90 metadata arrays and will convert them to
v1.0 metadata. The array must not be dirty (i.e. it must not need a sync) and it
must not have a write-intent bitmap.
The old metadata will remain on the devices, but will appear older than the new
metadata and so will usually be ignored. The old metadata (or indeed the new
metadata) can be removed by giving the appropriate --metadata= option to
--zero-superblock.
The no-bitmap option can be used when an array has an internal bitmap which is
corrupt in some way so that assembling the array normally fails. It will cause any
internal bitmap to be ignored.
The bbl option will reserve space in each device for a bad block list. This will
be 4K in size and positioned near the end of any free space between the superblock
and the data.
The no-bbl option will cause any reservation of space for a bad block list to be
removed. If the bad block list contains entries, this will fail, as removing the
list could cause data corruption.
The ppl option will enable PPL for a RAID5 array and reserve space for PPL on each
device. There must be enough free space between the data and superblock and a
write-intent bitmap or journal must not be used.
The no-ppl option will disable PPL in the superblock.
The layout-original and layout-alternate options are for RAID0 arrays with non-
uniform devices size that were in use before Linux 5.4. If the array was being
used with Linux 3.13 or earlier, then to assemble the array on a new kernel,
--update=layout-original must be given. If the array was created and used with a
kernel from Linux 3.14 to Linux 5.3, then --update=layout-alternate must be given.
This only needs to be given once. Subsequent assembly of the array will happen
normally. For more information, see md(4).
The layout-unspecified option reverts the effect of layout-orignal or
layout-alternate and allows the array to be again used on a kernel prior to Linux
5.3. This option should be used with great caution.
--freeze-reshape
This option is intended to be used in start-up scripts during the initrd boot
phase. When the array under reshape is assembled during the initrd phase, this
option stops the reshape after the reshape-critical section has been restored. This
happens before the file system pivot operation and avoids loss of filesystem
context. Losing file system context would cause reshape to be broken.
Reshape can be continued later using the --continue option for the grow command.
For Manage mode:
-t, --test
Unless a more serious error occurred, mdadm will exit with a status of 2 if no
changes were made to the array and 0 if at least one change was made. This can be
useful when an indirect specifier such as missing, detached or faulty is used in
requesting an operation on the array. --test will report failure if these
specifiers didn't find any match.
-a, --add
hot-add listed devices. If a device appears to have recently been part of the
array (possibly it failed or was removed) the device is re-added as described in
the next point. If that fails or the device was never part of the array, the
device is added as a hot-spare. If the array is degraded, it will immediately
start to rebuild data onto that spare.
Note that this and the following options are only meaningful on array with
redundancy. They don't apply to RAID0 or Linear.
--re-add
re-add a device that was previously removed from an array. If the metadata on the
device reports that it is a member of the array, and the slot that it used is still
vacant, then the device will be added back to the array in the same position. This
will normally cause the data for that device to be recovered. However, based on
the event count on the device, the recovery may only require sections that are
flagged by a write-intent bitmap to be recovered or may not require any recovery at
all.
When used on an array that has no metadata (i.e. it was built with --build) it will
be assumed that bitmap-based recovery is enough to make the device fully consistent
with the array.
--re-add can also be accompanied by --update=devicesize, --update=bbl, or
--update=no-bbl. See descriptions of these options when used in Assemble mode for
an explanation of their use.
If the device name given is missing then mdadm will try to find any device that
looks like it should be part of the array but isn't and will try to re-add all such
devices.
If the device name given is faulty then mdadm will find all devices in the array
that are marked faulty, remove them and attempt to immediately re-add them. This
can be useful if you are certain that the reason for failure has been resolved.
--add-spare
Add a device as a spare. This is similar to --add except that it does not attempt
--re-add first. The device will be added as a spare even if it looks like it could
be a recent member of the array.
-r, --remove
remove listed devices. They must not be active. i.e. they should be failed or
spare devices.
As well as the name of a device file (e.g. /dev/sda1) the words failed, detached
and names like set-A can be given to --remove. The first causes all failed devices
to be removed. The second causes any device which is no longer connected to the
system (i.e an 'open' returns ENXIO) to be removed. The third will remove a set as
described below under --fail.
-f, --fail
Mark listed devices as faulty. As well as the name of a device file, the word
detached or a set name like set-A can be given. The former will cause any device
that has been detached from the system to be marked as failed. It can then be
removed.
For RAID10 arrays where the number of copies evenly divides the number of devices,
the devices can be conceptually divided into sets where each set contains a single
complete copy of the data on the array. Sometimes a RAID10 array will be
configured so that these sets are on separate controllers. In this case, all the
devices in one set can be failed by giving a name like set-A or set-B to --fail.
The appropriate set names are reported by --detail.
--set-faulty
same as --fail.
--replace
Mark listed devices as requiring replacement. As soon as a spare is available, it
will be rebuilt and will replace the marked device. This is similar to marking a
device as faulty, but the device remains in service during the recovery process to
increase resilience against multiple failures. When the replacement process
finishes, the replaced device will be marked as faulty.
--with This can follow a list of --replace devices. The devices listed after --with will
preferentially be used to replace the devices listed after --replace. These
devices must already be spare devices in the array.
--write-mostly
Subsequent devices that are added or re-added will have the 'write-mostly' flag
set. This is only valid for RAID1 and means that the 'md' driver will avoid
reading from these devices if possible.
--readwrite
Subsequent devices that are added or re-added will have the 'write-mostly' flag
cleared.
--cluster-confirm
Confirm the existence of the device. This is issued in response to an --add request
by a node in a cluster. When a node adds a device it sends a message to all nodes
in the cluster to look for a device with a UUID. This translates to a udev
notification with the UUID of the device to be added and the slot number. The
receiving node must acknowledge this message with --cluster-confirm. Valid
arguments are <slot>:<devicename> in case the device is found or <slot>:missing in
case the device is not found.
--add-journal
Add a journal to an existing array, or recreate journal for a RAID-4/5/6 array that
lost a journal device. To avoid interrupting ongoing write operations, --add-
journal only works for array in Read-Only state.
--failfast
Subsequent devices that are added or re-added will have the 'failfast' flag set.
This is only valid for RAID1 and RAID10 and means that the 'md' driver will avoid
long timeouts on error handling where possible.
--nofailfast
Subsequent devices that are re-added will be re-added without the 'failfast' flag
set.
Each of these options requires that the first device listed is the array to be acted upon,
and the remainder are component devices to be added, removed, marked as faulty, etc.
Several different operations can be specified for different devices, e.g.
mdadm /dev/md0 --add /dev/sda1 --fail /dev/sdb1 --remove /dev/sdb1
Each operation applies to all devices listed until the next operation.
If an array is using a write-intent bitmap, then devices which have been removed can be
re-added in a way that avoids a full reconstruction but instead just updates the blocks
that have changed since the device was removed. For arrays with persistent metadata
(superblocks) this is done automatically. For arrays created with --build mdadm needs to
be told that this device we removed recently with --re-add.
Devices can only be removed from an array if they are not in active use, i.e. that must be
spares or failed devices. To remove an active device, it must first be marked as faulty.
For Misc mode:
-Q, --query
Examine a device to see (1) if it is an md device and (2) if it is a component of
an md array. Information about what is discovered is presented.
-D, --detail
Print details of one or more md devices.
--detail-platform
Print details of the platform's RAID capabilities (firmware / hardware topology)
for a given metadata format. If used without an argument, mdadm will scan all
controllers looking for their capabilities. Otherwise, mdadm will only look at the
controller specified by the argument in the form of an absolute filepath or a link,
e.g. /sys/devices/pci0000:00/0000:00:1f.2.
-Y, --export
When used with --detail, --detail-platform, --examine, or --incremental output will
be formatted as key=value pairs for easy import into the environment.
With --incremental The value MD_STARTED indicates whether an array was started
(yes) or not, which may include a reason (unsafe, nothing, no). Also the value
MD_FOREIGN indicates if the array is expected on this host (no), or seems to be
from elsewhere (yes).
-E, --examine
Print contents of the metadata stored on the named device(s). Note the contrast
between --examine and --detail. --examine applies to devices which are components
of an array, while --detail applies to a whole array which is currently active.
--sparc2.2
If an array was created on a SPARC machine with a 2.2 Linux kernel patched with
RAID support, the superblock will have been created incorrectly, or at least
incompatibly with 2.4 and later kernels. Using the --sparc2.2 flag with --examine
will fix the superblock before displaying it. If this appears to do the right
thing, then the array can be successfully assembled using --assemble
--update=sparc2.2.
-X, --examine-bitmap
Report information about a bitmap file. The argument is either an external bitmap
file or an array component in case of an internal bitmap. Note that running this
on an array device (e.g. /dev/md0) does not report the bitmap for that array.
--examine-badblocks
List the bad-blocks recorded for the device, if a bad-blocks list has been
configured. Currently only 1.x and IMSM metadata support bad-blocks lists.
--dump=directory
--restore=directory
Save metadata from lists devices, or restore metadata to listed devices.
-R, --run
start a partially assembled array. If --assemble did not find enough devices to
fully start the array, it might leaving it partially assembled. If you wish, you
can then use --run to start the array in degraded mode.
-S, --stop
deactivate array, releasing all resources.
-o, --readonly
mark array as readonly.
-w, --readwrite
mark array as readwrite.
--zero-superblock
If the device contains a valid md superblock, the block is overwritten with zeros.
With --force the block where the superblock would be is overwritten even if it
doesn't appear to be valid.
Note: Be careful when calling --zero-superblock with clustered raid. Make sure the
array isn't used or assembled in another cluster node before executing it.
--kill-subarray=
If the device is a container and the argument to --kill-subarray specifies an
inactive subarray in the container, then the subarray is deleted. Deleting all
subarrays will leave an 'empty-container' or spare superblock on the drives. See
--zero-superblock for completely removing a superblock. Note that some formats
depend on the subarray index for generating a UUID, this command will fail if it
would change the UUID of an active subarray.
--update-subarray=
If the device is a container and the argument to --update-subarray specifies a
subarray in the container, then attempt to update the given superblock field in the
subarray. See below in MISC MODE for details.
-t, --test
When used with --detail, the exit status of mdadm is set to reflect the status of
the device. See below in MISC MODE for details.
-W, --wait
For each md device given, wait for any resync, recovery, or reshape activity to
finish before returning. mdadm will return with success if it actually waited for
every device listed, otherwise it will return failure.
--wait-clean
For each md device given, or each device in /proc/mdstat if --scan is given,
arrange for the array to be marked clean as soon as possible. mdadm will return
with success if the array uses external metadata and we successfully waited. For
native arrays, this returns immediately as the kernel handles dirty-clean
transitions at shutdown. No action is taken if safe-mode handling is disabled.
--action=
Set the "sync_action" for all md devices given to one of idle, frozen, check,
repair. Setting to idle will abort any currently running action though some
actions will automatically restart. Setting to frozen will abort any current
action and ensure no other action starts automatically.
Details of check and repair can be found in md(4) under SCRUBBING AND MISMATCHES.
For Incremental Assembly mode:
--rebuild-map, -r
Rebuild the map file (/run/mdadm/map) that mdadm uses to help track which arrays
are currently being assembled.
--run, -R
Run any array assembled as soon as a minimal number of devices is available, rather
than waiting until all expected devices are present.
--scan, -s
Only meaningful with -R this will scan the map file for arrays that are being
incrementally assembled and will try to start any that are not already started. If
any such array is listed in mdadm.conf as requiring an external bitmap, that bitmap
will be attached first.
--fail, -f
This allows the hot-plug system to remove devices that have fully disappeared from
the kernel. It will first fail and then remove the device from any array it
belongs to. The device name given should be a kernel device name such as "sda",
not a name in /dev.
--path=
Only used with --fail. The 'path' given will be recorded so that if a new device
appears at the same location it can be automatically added to the same array. This
allows the failed device to be automatically replaced by a new device without
metadata if it appears at specified path. This option is normally only set by an
udev script.
For Monitor mode:
-m, --mail
Give a mail address to send alerts to.
-p, --program, --alert
Give a program to be run whenever an event is detected.
-y, --syslog
Cause all events to be reported through 'syslog'. The messages have facility of
'daemon' and varying priorities.
-d, --delay
Give a delay in seconds. mdadm polls the md arrays and then waits this many
seconds before polling again. The default is 60 seconds. Since 2.6.16, there is
no need to reduce this as the kernel alerts mdadm immediately when there is any
change.
-r, --increment
Give a percentage increment. mdadm will generate RebuildNN events with the given
percentage increment.
-f, --daemonise
Tell mdadm to run as a background daemon if it decides to monitor anything. This
causes it to fork and run in the child, and to disconnect from the terminal. The
process id of the child is written to stdout. This is useful with --scan which
will only continue monitoring if a mail address or alert program is found in the
config file.
-i, --pid-file
When mdadm is running in daemon mode, write the pid of the daemon process to the
specified file, instead of printing it on standard output.
-1, --oneshot
Check arrays only once. This will generate NewArray events and more significantly
DegradedArray and SparesMissing events. Running
mdadm --monitor --scan -1
from a cron script will ensure regular notification of any degraded arrays.
-t, --test
Generate a TestMessage alert for every array found at startup. This alert gets
mailed and passed to the alert program. This can be used for testing that alert
message do get through successfully.
--no-sharing
This inhibits the functionality for moving spares between arrays. Only one
monitoring process started with --scan but without this flag is allowed, otherwise
the two could interfere with each other.
ASSEMBLE MODE
Usage: mdadm --assemble md-device options-and-component-devices...
Usage: mdadm --assemble --scan md-devices-and-options...
Usage: mdadm --assemble --scan options...
This usage assembles one or more RAID arrays from pre-existing components. For each
array, mdadm needs to know the md device, the identity of the array, and the number of
component devices. These can be found in a number of ways.
In the first usage example (without the --scan) the first device given is the md device.
In the second usage example, all devices listed are treated as md devices and assembly is
attempted. In the third (where no devices are listed) all md devices that are listed in
the configuration file are assembled. If no arrays are described by the configuration
file, then any arrays that can be found on unused devices will be assembled.
If precisely one device is listed, but --scan is not given, then mdadm acts as though
--scan was given and identity information is extracted from the configuration file.
The identity can be given with the --uuid option, the --name option, or the --super-minor
option, will be taken from the md-device record in the config file, or will be taken from
the super block of the first component-device listed on the command line.
Devices can be given on the --assemble command line or in the config file. Only devices
which have an md superblock which contains the right identity will be considered for any
array.
The config file is only used if explicitly named with --config or requested with (a
possibly implicit) --scan. In the latter case, the default config file is used. See
mdadm.conf(5) for more details.
If --scan is not given, then the config file will only be used to find the identity of md
arrays.
Normally the array will be started after it is assembled. However if --scan is not given
and not all expected drives were listed, then the array is not started (to guard against
usage errors). To insist that the array be started in this case (as may work for RAID1,
4, 5, 6, or 10), give the --run flag.
If udev is active, mdadm does not create any entries in /dev but leaves that to udev. It
does record information in /run/mdadm/map which will allow udev to choose the correct
name.
If mdadm detects that udev is not configured, it will create the devices in /dev itself.
In Linux kernels prior to version 2.6.28 there were two distinct types of md devices that
could be created: one that could be partitioned using standard partitioning tools and one
that could not. Since 2.6.28 that distinction is no longer relevant as both types of
devices can be partitioned. mdadm will normally create the type that originally could not
be partitioned as it has a well-defined major number (9).
Prior to 2.6.28, it is important that mdadm chooses the correct type of array device to
use. This can be controlled with the --auto option. In particular, a value of "mdp" or
"part" or "p" tells mdadm to use a partitionable device rather than the default.
In the no-udev case, the value given to --auto can be suffixed by a number. This tells
mdadm to create that number of partition devices rather than the default of 4.
The value given to --auto can also be given in the configuration file as a word starting
auto= on the ARRAY line for the relevant array.
Auto-Assembly
When --assemble is used with --scan and no devices are listed, mdadm will first attempt to
assemble all the arrays listed in the config file.
If no arrays are listed in the config (other than those marked <ignore>) it will look
through the available devices for possible arrays and will try to assemble anything that
it finds. Arrays which are tagged as belonging to the given homehost will be assembled
and started normally. Arrays which do not obviously belong to this host are given names
that are expected not to conflict with anything local, and are started "read-auto" so that
nothing is written to any device until the array is written to. i.e. automatic resync etc
is delayed.
If mdadm finds a consistent set of devices that look like they should comprise an array,
and if the superblock is tagged as belonging to the given home host, it will automatically
choose a device name and try to assemble the array. If the array uses version-0.90
metadata, then the minor number as recorded in the superblock is used to create a name in
/dev/md/ so for example /dev/md/3. If the array uses version-1 metadata, then the name
from the superblock is used to similarly create a name in /dev/md/ (the name will have any
'host' prefix stripped first).
This behaviour can be modified by the AUTO line in the mdadm.conf configuration file.
This line can indicate that specific metadata type should, or should not, be automatically
assembled. If an array is found which is not listed in mdadm.conf and has a metadata
format that is denied by the AUTO line, then it will not be assembled. The AUTO line can
also request that all arrays identified as being for this homehost should be assembled
regardless of their metadata type. See mdadm.conf(5) for further details.
Note: Auto-assembly cannot be used for assembling and activating some arrays which are
undergoing reshape. In particular as the backup-file cannot be given, any reshape which
requires a backup file to continue cannot be started by auto-assembly. An array which is
growing to more devices and has passed the critical section can be assembled using auto-
assembly.
BUILD MODE
Usage: mdadm --build md-device --chunk=X --level=Y --raid-devices=Z devices
This usage is similar to --create. The difference is that it creates an array without a
superblock. With these arrays there is no difference between initially creating the array
and subsequently assembling the array, except that hopefully there is useful data there in
the second case.
The level may raid0, linear, raid1, raid10, multipath, or faulty, or one of their
synonyms. All devices must be listed and the array will be started once complete. It
will often be appropriate to use --assume-clean with levels raid1 or raid10.
CREATE MODE
Usage: mdadm --create md-device --chunk=X --level=Y
--raid-devices=Z devices
This usage will initialise a new md array, associate some devices with it, and activate
the array.
The named device will normally not exist when mdadm --create is run, but will be created
by udev once the array becomes active.
The max length md-device name is limited to 32 characters. Different metadata types have
more strict limitation (like IMSM where only 16 characters are allowed). For that reason,
long name could be truncated or rejected, it depends on metadata policy.
As devices are added, they are checked to see if they contain RAID superblocks or
filesystems. They are also checked to see if the variance in device size exceeds 1%.
If any discrepancy is found, the array will not automatically be run, though the presence
of a --run can override this caution.
To create a "degraded" array in which some devices are missing, simply give the word
"missing" in place of a device name. This will cause mdadm to leave the corresponding
slot in the array empty. For a RAID4 or RAID5 array at most one slot can be "missing";
for a RAID6 array at most two slots. For a RAID1 array, only one real device needs to be
given. All of the others can be "missing".
When creating a RAID5 array, mdadm will automatically create a degraded array with an
extra spare drive. This is because building the spare into a degraded array is in general
faster than resyncing the parity on a non-degraded, but not clean, array. This feature
can be overridden with the --force option.
When creating an array with version-1 metadata a name for the array is required. If this
is not given with the --name option, mdadm will choose a name based on the last component
of the name of the device being created. So if /dev/md3 is being created, then the name 3
will be chosen. If /dev/md/home is being created, then the name home will be used.
When creating a partition based array, using mdadm with version-1.x metadata, the
partition type should be set to 0xDA (non fs-data). This type of selection allows for
greater precision since using any other [RAID auto-detect (0xFD) or a GNU/Linux partition
(0x83)], might create problems in the event of array recovery through a live cdrom.
A new array will normally get a randomly assigned 128bit UUID which is very likely to be
unique. If you have a specific need, you can choose a UUID for the array by giving the
--uuid= option. Be warned that creating two arrays with the same UUID is a recipe for
disaster. Also, using --uuid= when creating a v0.90 array will silently override any
--homehost= setting.
If the array type supports a write-intent bitmap, and if the devices in the array exceed
100G is size, an internal write-intent bitmap will automatically be added unless some
other option is explicitly requested with the --bitmap option or a different consistency
policy is selected with the --consistency-policy option. In any case, space for a bitmap
will be reserved so that one can be added later with --grow --bitmap=internal.
If the metadata type supports it (currently only 1.x and IMSM metadata), space will be
allocated to store a bad block list. This allows a modest number of bad blocks to be
recorded, allowing the drive to remain in service while only partially functional.
When creating an array within a CONTAINER mdadm can be given either the list of devices to
use, or simply the name of the container. The former case gives control over which
devices in the container will be used for the array. The latter case allows mdadm to
automatically choose which devices to use based on how much spare space is available.
The General Management options that are valid with --create are:
--run insist on running the array even if some devices look like they might be in use.
--readonly
start the array in readonly mode.
MANAGE MODE
Usage: mdadm device options... devices...
This usage will allow individual devices in an array to be failed, removed or added. It
is possible to perform multiple operations with on command. For example:
mdadm /dev/md0 -f /dev/hda1 -r /dev/hda1 -a /dev/hda1
will firstly mark /dev/hda1 as faulty in /dev/md0 and will then remove it from the array
and finally add it back in as a spare. However, only one md array can be affected by a
single command.
When a device is added to an active array, mdadm checks to see if it has metadata on it
which suggests that it was recently a member of the array. If it does, it tries to
"re-add" the device. If there have been no changes since the device was removed, or if
the array has a write-intent bitmap which has recorded whatever changes there were, then
the device will immediately become a full member of the array and those differences
recorded in the bitmap will be resolved.
MISC MODE
Usage: mdadm options ... devices ...
MISC mode includes a number of distinct operations that operate on distinct devices. The
operations are:
--query
The device is examined to see if it is (1) an active md array, or (2) a component
of an md array. The information discovered is reported.
--detail
The device should be an active md device. mdadm will display a detailed
description of the array. --brief or --scan will cause the output to be less
detailed and the format to be suitable for inclusion in mdadm.conf. The exit
status of mdadm will normally be 0 unless mdadm failed to get useful information
about the device(s); however, if the --test option is given, then the exit status
will be:
0 The array is functioning normally.
1 The array has at least one failed device.
2 The array has multiple failed devices such that it is unusable.
4 There was an error while trying to get information about the device.
--detail-platform
Print detail of the platform's RAID capabilities (firmware / hardware topology).
If the metadata is specified with -e or --metadata= then the return status will be:
0 metadata successfully enumerated its platform components on this system
1 metadata is platform independent
2 metadata failed to find its platform components on this system
--update-subarray=
If the device is a container and the argument to --update-subarray specifies a
subarray in the container, then attempt to update the given superblock field in the
subarray. Similar to updating an array in "assemble" mode, the field to update is
selected by -U or --update= option. The supported options are name, ppl, no-ppl,
bitmap and no-bitmap.
The name option updates the subarray name in the metadata, it may not affect the
device node name or the device node symlink until the subarray is re-assembled. If
updating name would change the UUID of an active subarray this operation is
blocked, and the command will end in an error.
The ppl and no-ppl options enable and disable PPL in the metadata. Currently
supported only for IMSM subarrays.
The bitmap and no-bitmap options enable and disable write-intent bitmap in the
metadata. Currently supported only for IMSM subarrays.
--examine
The device should be a component of an md array. mdadm will read the md superblock
of the device and display the contents. If --brief or --scan is given, then
multiple devices that are components of the one array are grouped together and
reported in a single entry suitable for inclusion in mdadm.conf.
Having --scan without listing any devices will cause all devices listed in the
config file to be examined.
--dump=directory
If the device contains RAID metadata, a file will be created in the directory and
the metadata will be written to it. The file will be the same size as the device
and will have the metadata written at the same location as it exists in the device.
However, the file will be "sparse" so that only those blocks containing metadata
will be allocated. The total space used will be small.
The filename used in the directory will be the base name of the device. Further,
if any links appear in /dev/disk/by-id which point to the device, then hard links
to the file will be created in directory based on these by-id names.
Multiple devices can be listed and their metadata will all be stored in the one
directory.
--restore=directory
This is the reverse of --dump. mdadm will locate a file in the directory that has
a name appropriate for the given device and will restore metadata from it. Names
that match /dev/disk/by-id names are preferred, however if two of those refer to
different files, mdadm will not choose between them but will abort the operation.
If a file name is given instead of a directory then mdadm will restore from that
file to a single device, always provided the size of the file matches that of the
device, and the file contains valid metadata.
--stop The devices should be active md arrays which will be deactivated, as long as they
are not currently in use.
--run This will fully activate a partially assembled md array.
--readonly
This will mark an active array as read-only, providing that it is not currently
being used.
--readwrite
This will change a readonly array back to being read/write.
--scan For all operations except --examine, --scan will cause the operation to be applied
to all arrays listed in /proc/mdstat. For --examine, --scan causes all devices
listed in the config file to be examined.
-b, --brief
Be less verbose. This is used with --detail and --examine. Using --brief with
--verbose gives an intermediate level of verbosity.
MONITOR MODE
Usage: mdadm --monitor options... devices...
Monitor option can work in two modes:
• system wide mode, follow all md devices based on /proc/mdstat,
• follow only specified MD devices in command line.
--scan - indicates system wide mode. Option causes the monitor to track all md devices
that appear in /proc/mdstat. If it is not set, then at least one device must be
specified.
Monitor usage causes mdadm to periodically poll a number of md arrays and to report on any
events noticed.
In both modes, monitor will work as long as there is an active array with redundancy and
it is defined to follow (for --scan every array is followed).
As well as reporting events, mdadm may move a spare drive from one array to another if
they are in the same spare-group or domain and if the destination array has a failed drive
but no spares.
The result of monitoring the arrays is the generation of events. These events are passed
to a separate program (if specified) and may be mailed to a given E-mail address.
When passing events to a program, the program is run once for each event, and is given 2
or 3 command-line arguments: the first is the name of the event (see below), the second is
the name of the md device which is affected, and the third is the name of a related device
if relevant (such as a component device that has failed).
If --scan is given, then a program or an e-mail address must be specified on the command
line or in the config file. If neither are available, then mdadm will not monitor
anything. For devices given directly in command line, without program or email specified,
each event is reported to stdout.
Note: For systems where is configured via systemd, mdmonitor(mdmonitor.service) should be
configured. The service is designed to be primary solution for array monitoring, it is
configured to work in system wide mode. It is automatically started and stopped according
to current state and types of MD arrays in system. The service may require additional
configuration, like e-mail or delay. That should be done in mdadm.conf.
The different events are:
DeviceDisappeared
An md array which previously was configured appears to no longer be configured.
(syslog priority: Critical)
If mdadm was told to monitor an array which is RAID0 or Linear, then it will
report DeviceDisappeared with the extra information Wrong-Level. This is
because RAID0 and Linear do not support the device-failed, hot-spare and resync
operations which are monitored.
RebuildStarted
An md array started reconstruction (e.g. recovery, resync, reshape, check,
repair). (syslog priority: Warning)
RebuildNN
Where NN is a two-digit number (eg. 05, 48). This indicates that the rebuild
has reached that percentage of the total. The events are generated at a fixed
increment from 0. The increment size may be specified with a command-line
option (the default is 20). (syslog priority: Warning)
RebuildFinished
An md array that was rebuilding, isn't any more, either because it finished
normally or was aborted. (syslog priority: Warning)
Fail An active component device of an array has been marked as faulty. (syslog
priority: Critical)
FailSpare
A spare component device which was being rebuilt to replace a faulty device has
failed. (syslog priority: Critical)
SpareActive
A spare component device which was being rebuilt to replace a faulty device has
been successfully rebuilt and has been made active. (syslog priority: Info)
NewArray
A new md array has been detected in the /proc/mdstat file. (syslog priority:
Info)
DegradedArray
A newly noticed array appears to be degraded. This message is not generated
when mdadm notices a drive failure which causes degradation, but only when
mdadm notices that an array is degraded when it first sees the array. (syslog
priority: Critical)
MoveSpare
A spare drive has been moved from one array in a spare-group or domain to
another to allow a failed drive to be replaced. (syslog priority: Info)
SparesMissing
If mdadm has been told, via the config file, that an array should have a
certain number of spare devices, and mdadm detects that it has fewer than this
number when it first sees the array, it will report a SparesMissing message.
(syslog priority: Warning)
TestMessage
An array was found at startup, and the --test flag was given. (syslog
priority: Info)
Only Fail, FailSpare, DegradedArray, SparesMissing and TestMessage cause Email to be sent.
All events cause the program to be run. The program is run with two or three arguments:
the event name, the array device and possibly a second device.
Each event has an associated array device (e.g. /dev/md1) and possibly a second device.
For Fail, FailSpare, and SpareActive the second device is the relevant component device.
For MoveSpare the second device is the array that the spare was moved from.
For mdadm to move spares from one array to another, the different arrays need to be
labeled with the same spare-group or the spares must be allowed to migrate through
matching POLICY domains in the configuration file. The spare-group name can be any
string; it is only necessary that different spare groups use different names.
When mdadm detects that an array in a spare group has fewer active devices than necessary
for the complete array, and has no spare devices, it will look for another array in the
same spare group that has a full complement of working drives and a spare. It will then
attempt to remove the spare from the second array and add it to the first. If the removal
succeeds but the adding fails, then it is added back to the original array.
If the spare group for a degraded array is not defined, mdadm will look at the rules of
spare migration specified by POLICY lines in mdadm.conf and then follow similar steps as
above if a matching spare is found.
GROW MODE
The GROW mode is used for changing the size or shape of an active array.
During the kernel 2.6 era the following changes were added:
• change the "size" attribute for RAID1, RAID4, RAID5 and RAID6.
• increase or decrease the "raid-devices" attribute of RAID0, RAID1, RAID4, RAID5, and
RAID6.
• change the chunk-size and layout of RAID0, RAID4, RAID5, RAID6 and RAID10.
• convert between RAID1 and RAID5, between RAID5 and RAID6, between RAID0, RAID4, and
RAID5, and between RAID0 and RAID10 (in the near-2 mode).
• add a write-intent bitmap to any array which supports these bitmaps, or remove a
write-intent bitmap from such an array.
• change the array's consistency policy.
Using GROW on containers is currently supported only for Intel's IMSM container format.
The number of devices in a container can be increased - which affects all arrays in the
container - or an array in a container can be converted between levels where those levels
are supported by the container, and the conversion is on of those listed above.
Notes:
• Intel's native checkpointing doesn't use --backup-file option and it is transparent
for assembly feature.
• Roaming between Windows(R) and Linux systems for IMSM metadata is not supported during
grow process.
• When growing a raid0 device, the new component disk size (or external backup size)
should be larger than LCM(old, new) * chunk-size * 2, where LCM() is the least common
multiple of the old and new count of component disks, and "* 2" comes from the fact
that mdadm refuses to use more than half of a spare device for backup space.
SIZE CHANGES
Normally when an array is built the "size" is taken from the smallest of the drives. If
all the small drives in an arrays are, over time, removed and replaced with larger drives,
then you could have an array of large drives with only a small amount used. In this
situation, changing the "size" with "GROW" mode will allow the extra space to start being
used. If the size is increased in this way, a "resync" process will start to make sure
the new parts of the array are synchronised.
Note that when an array changes size, any filesystem that may be stored in the array will
not automatically grow or shrink to use or vacate the space. The filesystem will need to
be explicitly told to use the extra space after growing, or to reduce its size prior to
shrinking the array.
Also, the size of an array cannot be changed while it has an active bitmap. If an array
has a bitmap, it must be removed before the size can be changed. Once the change is
complete a new bitmap can be created.
Note: --grow --size is not yet supported for external file bitmap.
RAID-DEVICES CHANGES
A RAID1 array can work with any number of devices from 1 upwards (though 1 is not very
useful). There may be times which you want to increase or decrease the number of active
devices. Note that this is different to hot-add or hot-remove which changes the number of
inactive devices.
When reducing the number of devices in a RAID1 array, the slots which are to be removed
from the array must already be vacant. That is, the devices which were in those slots
must be failed and removed.
When the number of devices is increased, any hot spares that are present will be activated
immediately.
Changing the number of active devices in a RAID5 or RAID6 is much more effort. Every
block in the array will need to be read and written back to a new location. From 2.6.17,
the Linux Kernel is able to increase the number of devices in a RAID5 safely, including
restarting an interrupted "reshape". From 2.6.31, the Linux Kernel is able to increase or
decrease the number of devices in a RAID5 or RAID6.
From 2.6.35, the Linux Kernel is able to convert a RAID0 in to a RAID4 or RAID5. mdadm
uses this functionality and the ability to add devices to a RAID4 to allow devices to be
added to a RAID0. When requested to do this, mdadm will convert the RAID0 to a RAID4, add
the necessary disks and make the reshape happen, and then convert the RAID4 back to RAID0.
When decreasing the number of devices, the size of the array will also decrease. If there
was data in the array, it could get destroyed and this is not reversible, so you should
firstly shrink the filesystem on the array to fit within the new size. To help prevent
accidents, mdadm requires that the size of the array be decreased first with mdadm --grow
--array-size. This is a reversible change which simply makes the end of the array
inaccessible. The integrity of any data can then be checked before the non-reversible
reduction in the number of devices is request.
When relocating the first few stripes on a RAID5 or RAID6, it is not possible to keep the
data on disk completely consistent and crash-proof. To provide the required safety, mdadm
disables writes to the array while this "critical section" is reshaped, and takes a backup
of the data that is in that section. For grows, this backup may be stored in any spare
devices that the array has, however it can also be stored in a separate file specified
with the --backup-file option, and is required to be specified for shrinks, RAID level
changes and layout changes. If this option is used, and the system does crash during the
critical period, the same file must be passed to --assemble to restore the backup and
reassemble the array. When shrinking rather than growing the array, the reshape is done
from the end towards the beginning, so the "critical section" is at the end of the
reshape.
LEVEL CHANGES
Changing the RAID level of any array happens instantaneously. However in the RAID5 to
RAID6 case this requires a non-standard layout of the RAID6 data, and in the RAID6 to
RAID5 case that non-standard layout is required before the change can be accomplished. So
while the level change is instant, the accompanying layout change can take quite a long
time. A --backup-file is required. If the array is not simultaneously being grown or
shrunk, so that the array size will remain the same - for example, reshaping a 3-drive
RAID5 into a 4-drive RAID6 - the backup file will be used not just for a "critical
section" but throughout the reshape operation, as described below under LAYOUT CHANGES.
CHUNK-SIZE AND LAYOUT CHANGES
Changing the chunk-size or layout without also changing the number of devices as the same
time will involve re-writing all blocks in-place. To ensure against data loss in the case
of a crash, a --backup-file must be provided for these changes. Small sections of the
array will be copied to the backup file while they are being rearranged. This means that
all the data is copied twice, once to the backup and once to the new layout on the array,
so this type of reshape will go very slowly.
If the reshape is interrupted for any reason, this backup file must be made available to
mdadm --assemble so the array can be reassembled. Consequently, the file cannot be stored
on the device being reshaped.
BITMAP CHANGES
A write-intent bitmap can be added to, or removed from, an active array. Either internal
bitmaps, or bitmaps stored in a separate file, can be added. Note that if you add a
bitmap stored in a file which is in a filesystem that is on the RAID array being affected,
the system will deadlock. The bitmap must be on a separate filesystem.
CONSISTENCY POLICY CHANGES
The consistency policy of an active array can be changed by using the --consistency-policy
option in Grow mode. Currently this works only for the ppl and resync policies and allows
one to enable or disable the RAID5 Partial Parity Log (PPL).
INCREMENTAL MODE
Usage: mdadm --incremental [--run] [--quiet] component-device [optional-aliases-for-
device]
Usage: mdadm --incremental --fail component-device
Usage: mdadm --incremental --rebuild-map
Usage: mdadm --incremental --run --scan
This mode is designed to be used in conjunction with a device discovery system. As
devices are found in a system, they can be passed to mdadm --incremental to be
conditionally added to an appropriate array.
Conversely, it can also be used with the --fail flag to do just the opposite and find
whatever array a particular device is part of and remove the device from that array.
If the device passed is a CONTAINER device created by a previous call to mdadm, then
rather than trying to add that device to an array, all the arrays described by the
metadata of the container will be started.
mdadm performs a number of tests to determine if the device is part of an array, and which
array it should be part of. If an appropriate array is found, or can be created, mdadm
adds the device to the array and conditionally starts the array.
Note that mdadm will normally only add devices to an array which were previously working
(active or spare) parts of that array. The support for automatic inclusion of a new drive
as a spare in some array requires a configuration through POLICY in config file.
The tests that mdadm makes are as follow:
+ Is the device permitted by mdadm.conf? That is, is it listed in a DEVICES line in
that file. If DEVICES is absent then the default it to allow any device.
Similarly if DEVICES contains the special word partitions then any device is
allowed. Otherwise the device name given to mdadm, or one of the aliases given, or
an alias found in the filesystem, must match one of the names or patterns in a
DEVICES line.
This is the only context where the aliases are used. They are usually provided by
a udev rules mentioning $env{DEVLINKS}.
+ Does the device have a valid md superblock? If a specific metadata version is
requested with --metadata or -e then only that style of metadata is accepted,
otherwise mdadm finds any known version of metadata. If no md metadata is found,
the device may be still added to an array as a spare if POLICY allows.
mdadm keeps a list of arrays that it has partially assembled in /run/mdadm/map. If no
array exists which matches the metadata on the new device, mdadm must choose a device name
and unit number. It does this based on any name given in mdadm.conf or any name
information stored in the metadata. If this name suggests a unit number, that number will
be used, otherwise a free unit number will be chosen. Normally mdadm will prefer to
create a partitionable array, however if the CREATE line in mdadm.conf suggests that a
non-partitionable array is preferred, that will be honoured.
If the array is not found in the config file and its metadata does not identify it as
belonging to the "homehost", then mdadm will choose a name for the array which is certain
not to conflict with any array which does belong to this host. It does this be adding an
underscore and a small number to the name preferred by the metadata.
Once an appropriate array is found or created and the device is added, mdadm must decide
if the array is ready to be started. It will normally compare the number of available
(non-spare) devices to the number of devices that the metadata suggests need to be active.
If there are at least that many, the array will be started. This means that if any
devices are missing the array will not be restarted.
As an alternative, --run may be passed to mdadm in which case the array will be run as
soon as there are enough devices present for the data to be accessible. For a RAID1, that
means one device will start the array. For a clean RAID5, the array will be started as
soon as all but one drive is present.
Note that neither of these approaches is really ideal. If it can be known that all device
discovery has completed, then
mdadm -IRs
can be run which will try to start all arrays that are being incrementally assembled.
They are started in "read-auto" mode in which they are read-only until the first write
request. This means that no metadata updates are made and no attempt at resync or
recovery happens. Further devices that are found before the first write can still be
added safely.
ENVIRONMENT
This section describes environment variables that affect how mdadm operates.
MDADM_NO_MDMON
Setting this value to 1 will prevent mdadm from automatically launching mdmon.
This variable is intended primarily for debugging mdadm/mdmon.
MDADM_NO_UDEV
Normally, mdadm does not create any device nodes in /dev, but leaves that task to
udev. If udev appears not to be configured, or if this environment variable is set
to '1', the mdadm will create and devices that are needed.
MDADM_NO_SYSTEMCTL
If mdadm detects that systemd is in use it will normally request systemd to start
various background tasks (particularly mdmon) rather than forking and running them
in the background. This can be suppressed by setting MDADM_NO_SYSTEMCTL=1.
IMSM_NO_PLATFORM
A key value of IMSM metadata is that it allows interoperability with boot ROMs on
Intel platforms, and with other major operating systems. Consequently, mdadm will
only allow an IMSM array to be created or modified if detects that it is running on
an Intel platform which supports IMSM, and supports the particular configuration of
IMSM that is being requested (some functionality requires newer OROM support).
These checks can be suppressed by setting IMSM_NO_PLATFORM=1 in the environment.
This can be useful for testing or for disaster recovery. You should be aware that
interoperability may be compromised by setting this value.
These change can also be suppressed by adding mdadm.imsm.test=1 to the kernel
command line. This makes it easy to test IMSM code in a virtual machine that
doesn't have IMSM virtual hardware.
MDADM_GROW_ALLOW_OLD
If an array is stopped while it is performing a reshape and that reshape was making
use of a backup file, then when the array is re-assembled mdadm will sometimes
complain that the backup file is too old. If this happens and you are certain it
is the right backup file, you can over-ride this check by setting
MDADM_GROW_ALLOW_OLD=1 in the environment.
MDADM_CONF_AUTO
Any string given in this variable is added to the start of the AUTO line in the
config file, or treated as the whole AUTO line if none is given. It can be used to
disable certain metadata types when mdadm is called from a boot script. For
example
export MDADM_CONF_AUTO='-ddf -imsm'
will make sure that mdadm does not automatically assemble any DDF or IMSM arrays
that are found. This can be useful on systems configured to manage such arrays
with dmraid.
EXAMPLES
mdadm --query /dev/name-of-device
This will find out if a given device is a RAID array, or is part of one, and will provide
brief information about the device.
mdadm --assemble --scan
This will assemble and start all arrays listed in the standard config file. This command
will typically go in a system startup file.
mdadm --stop --scan
This will shut down all arrays that can be shut down (i.e. are not currently in use).
This will typically go in a system shutdown script.
mdadm --follow --scan --delay=120
If (and only if) there is an Email address or program given in the standard config file,
then monitor the status of all arrays listed in that file by polling them ever 2 minutes.
mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/hd[ac]1
Create /dev/md0 as a RAID1 array consisting of /dev/hda1 and /dev/hdc1.
echo 'DEVICE /dev/hd*[0-9] /dev/sd*[0-9]' > mdadm.conf
mdadm --detail --scan >> mdadm.conf
This will create a prototype config file that describes currently active arrays that are
known to be made from partitions of IDE or SCSI drives. This file should be reviewed
before being used as it may contain unwanted detail.
echo 'DEVICE /dev/hd[a-z] /dev/sd*[a-z]' > mdadm.conf
mdadm --examine --scan --config=mdadm.conf >> mdadm.conf
This will find arrays which could be assembled from existing IDE and SCSI whole drives
(not partitions), and store the information in the format of a config file. This file is
very likely to contain unwanted detail, particularly the devices= entries. It should be
reviewed and edited before being used as an actual config file.
mdadm --examine --brief --scan --config=partitions
mdadm -Ebsc partitions
Create a list of devices by reading /proc/partitions, scan these for RAID superblocks, and
printout a brief listing of all that were found.
mdadm -Ac partitions -m 0 /dev/md0
Scan all partitions and devices listed in /proc/partitions and assemble /dev/md0 out of
all such devices with a RAID superblock with a minor number of 0.
mdadm --monitor --scan --daemonise > /run/mdadm/mon.pid
If config file contains a mail address or alert program, run mdadm in the background in
monitor mode monitoring all md devices. Also write pid of mdadm daemon to
/run/mdadm/mon.pid.
mdadm -Iq /dev/somedevice
Try to incorporate newly discovered device into some array as appropriate.
mdadm --incremental --rebuild-map --run --scan
Rebuild the array map from any current arrays, and then start any that can be started.
mdadm /dev/md4 --fail detached --remove detached
Any devices which are components of /dev/md4 will be marked as faulty and then remove from
the array.
mdadm --grow /dev/md4 --level=6 --backup-file=/root/backup-md4
The array /dev/md4 which is currently a RAID5 array will be converted to RAID6. There
should normally already be a spare drive attached to the array as a RAID6 needs one more
drive than a matching RAID5.
mdadm --create /dev/md/ddf --metadata=ddf --raid-disks 6 /dev/sd[a-f]
Create a DDF array over 6 devices.
mdadm --create /dev/md/home -n3 -l5 -z 30000000 /dev/md/ddf
Create a RAID5 array over any 3 devices in the given DDF set. Use only 30 gigabytes of
each device.
mdadm -A /dev/md/ddf1 /dev/sd[a-f]
Assemble a pre-exist ddf array.
mdadm -I /dev/md/ddf1
Assemble all arrays contained in the ddf array, assigning names as appropriate.
mdadm --create --help
Provide help about the Create mode.
mdadm --config --help
Provide help about the format of the config file.
mdadm --help
Provide general help.
FILES
/proc/mdstat If you're using the /proc filesystem, /proc/mdstat lists all active md devices with information about them. mdadm uses this to find arrays when --scan is given in Misc mode, and to monitor array reconstruction on Monitor mode. /etc/mdadm.conf (or /etc/mdadm/mdadm.conf) Default config file. See mdadm.conf(5) for more details. /etc/mdadm.conf.d (or /etc/mdadm/mdadm.conf.d) Default directory containing configuration files. See mdadm.conf(5) for more details. /run/mdadm/map When --incremental mode is used, this file gets a list of arrays currently being created.
DEVICE NAMES
mdadm understand two sorts of names for array devices.
The first is the so-called 'standard' format name, which matches the names used by the
kernel and which appear in /proc/mdstat.
The second sort can be freely chosen, but must reside in /dev/md/. When giving a device
name to mdadm to create or assemble an array, either full path name such as /dev/md0 or
/dev/md/home can be given, or just the suffix of the second sort of name, such as home can
be given.
When mdadm chooses device names during auto-assembly or incremental assembly, it will
sometimes add a small sequence number to the end of the name to avoid conflicted between
multiple arrays that have the same name. If mdadm can reasonably determine that the array
really is meant for this host, either by a hostname in the metadata, or by the presence of
the array in mdadm.conf, then it will leave off the suffix if possible. Also if the
homehost is specified as <ignore> mdadm will only use a suffix if a different array of the
same name already exists or is listed in the config file.
The standard names for non-partitioned arrays (the only sort of md array available in 2.4
and earlier) are of the form
/dev/mdNN
where NN is a number. The standard names for partitionable arrays (as available from 2.6
onwards) are of the form:
/dev/md_dNN
Partition numbers should be indicated by adding "pMM" to these, thus "/dev/md/d1p2".
From kernel version 2.6.28 the "non-partitioned array" can actually be partitioned. So
the "md_dNN" names are no longer needed, and partitions such as "/dev/mdNNpXX" are
possible.
From kernel version 2.6.29 standard names can be non-numeric following the form:
/dev/md_XXX
where XXX is any string. These names are supported by mdadm since version 3.3 provided
they are enabled in mdadm.conf.
NOTE
mdadm was previously known as mdctl.
SEE ALSO
For further information on mdadm usage, MD and the various levels of RAID, see:
https://raid.wiki.kernel.org/
(based upon Jakob Østergaard's Software-RAID.HOWTO)
The latest version of mdadm should always be available from
https://www.kernel.org/pub/linux/utils/raid/mdadm/
Related man pages:
mdmon(8), mdadm.conf(5), md(4).