Provided by: netplan-generator_0.107-5ubuntu0.4_amd64 
NAME
netplan - YAML network configuration abstraction for various backends
SYNOPSIS
netplan [ COMMAND | help ]
COMMANDS
See netplan help for a list of available commands on this system.
DESCRIPTION
Introduction
Distribution installers, cloud instantiation, image builds for particular devices, or any
other way to deploy an operating system put its desired network configuration into YAML
configuration file(s). During early boot, the netplan "network renderer" runs which reads
/{lib,etc,run}/netplan/*.yaml and writes configuration to /run to hand off control of
devices to the specified networking daemon.
• Configured devices get handled by systemd-networkd by default, unless explicitly marked
as managed by a specific renderer (NetworkManager)
• Devices not covered by the network config do not get touched at all.
• Usable in initramfs (few dependencies and fast)
• No persistent generated config, only original YAML config
• Parser supports multiple config files to allow applications like libvirt or lxd to
package up expected network config (virbr0, lxdbr0), or to change the global default
policy to use NetworkManager for everything.
• Retains the flexibility to change backends/policy later or adjust to removing
NetworkManager, as generated configuration is ephemeral.
General structure
netplan's configuration files use the YAML (http://yaml.org/spec/1.1/current.html) format.
All /{lib,etc,run}/netplan/*.yaml are considered. Lexicographically later files
(regardless of in which directory they are) amend (new mapping keys) or override (same
mapping keys) previous ones. A file in /run/netplan completely shadows a file with same
name in /etc/netplan, and a file in either of those directories shadows a file with the
same name in /lib/netplan.
The top-level node in a netplan configuration file is a network: mapping that contains
version: 2 (the YAML currently being used by curtin, MaaS, etc. is version 1), and then
device definitions grouped by their type, such as ethernets:, modems:, wifis:, or
bridges:. These are the types that our renderer can understand and are supported by our
backends.
Each type block contains device definitions as a map where the keys (called "configuration
IDs") are defined as below.
Device configuration IDs
The key names below the per-device-type definition maps (like ethernets:) are called
"ID"s. They must be unique throughout the entire set of configuration files. Their
primary purpose is to serve as anchor names for composite devices, for example to
enumerate the members of a bridge that is currently being defined.
(Since 0.97) If an interface is defined with an ID in a configuration file; it will be
brought up by the applicable renderer. To not have netplan touch an interface at all, it
should be completely omitted from the netplan configuration files.
There are two physically/structurally different classes of device definitions, and the ID
field has a different interpretation for each:
Physical devices
(Examples: ethernet, modem, wifi) These can dynamically come and go between reboots
and even during runtime (hot plugging). In the generic case, they can be selected
by match: rules on desired properties, such as name/name pattern, MAC address,
driver, or device paths. In general these will match any number of devices (unless
they refer to properties which are unique such as the full path or MAC address), so
without further knowledge about the hardware these will always be considered as a
group.
It is valid to specify no match rules at all, in which case the ID field is simply
the interface name to be matched. This is mostly useful if you want to keep simple
cases simple, and it's how network device configuration has been done for a long
time.
If there are match: rules, then the ID field is a purely opaque name which is only
being used for references from definitions of compound devices in the config.
Virtual devices
(Examples: veth, bridge, bond, vrf) These are fully under the control of the config
file(s) and the network stack. I. e. these devices are being created instead of
matched. Thus match: and set-name: are not applicable for these, and the ID field
is the name of the created virtual device.
Top-level configuration structure
The general structure of a Netplan YAML file is shown below.
network:
version: NUMBER
renderer: STRING
bonds: MAPPING
bridges: MAPPING
dummy-devices: MAPPING
ethernets: MAPPING
modems: MAPPING
tunnels: MAPPING
virtual-ethernets: MAPPING
vlans: MAPPING
vrfs: MAPPING
wifis: MAPPING
nm-devices: MAPPING
• version (number)
Defines what version of the configuration format is used. The only value
supported is 2. Defaults to 2 if not defined.
• renderer (scalar)
Defines what network configuration tool will be used to set up your
configuration. Valid values are networkd and NetworkManager. Defaults to
networkd if not defined.
• bonds (mapping)
Creates and configures link aggregation (bonding) devices.
• bridges (mapping)
Creates and configures bridge devices.
• dummy-devices (mapping) – since 0.107
Creates and configures virtual devices.
• ethernets (mapping)
Configures physical Ethernet interfaces.
• modems (mapping)
Configures modems
• tunnels (mapping)
Creates and configures different types of virtual tunnels.
• virtual-ethernets (mapping) – since 0.107
Creates and configures Virtual Ethernet (veth) devices.
• vlans (mapping)
Creates and configures VLANs.
• vrfs (mapping)
Configures Virtual Routing and Forwarding (VRF) devices.
• wifis (mapping)
Configures physical Wifi interfaces as client, adhoc or access point.
• nm-devices (mapping)
nm-devices are used in situations where Netplan doesn't support the connection
type. The raw configuration expected by NetworkManager can be defined and will
be passed as is (passthrough) to the .nmconnection file. Users will not normally
use this type of device.
All the properties for all the device types will be described in the next sections.
Properties for physical device types
These properties are used with physical devices such as Ethernet and Wifi network
interfaces.
Note: Some options will not work reliably for devices matched by name only and rendered by
networkd, due to interactions with device renaming in udev. Match devices by MAC when
setting options like: wakeonlan or *-offload.
• match (mapping)
This selects a subset of available physical devices by various hardware
properties. The following configuration will then apply to all matching devices,
as soon as they appear. All specified properties must match.
• name (scalar)
Current interface name. Globs are supported, and the primary use case for
matching on names, as selecting one fixed name can be more easily achieved with
having no match: at all and just using the ID (see above). (NetworkManager: as
of v1.14.0)
• macaddress (scalar)
Device's 6-byte permanent MAC address in the form "XX:XX:XX:XX:XX:XX" or 20
bytes for InfiniBand devices (IPoIB). Globs are not allowed. This doesn't
match virtual MAC addresses for veth, bridge, bond, vlan, ...
• driver (scalar or sequence of scalars) – sequence since 0.104
Kernel driver name, corresponding to the DRIVER udev property. A sequence of
globs is supported, any of which must match. Matching on driver is only
supported with networkd.
Examples:
• All cards on second PCI bus:
network:
ethernets:
myinterface:
match:
name: enp2*
• Fixed MAC address:
network:
ethernets:
interface0:
match:
macaddress: 11:22:33:AA:BB:FF
• First card of driver ixgbe:
network:
ethernets:
nic0:
match:
driver: ixgbe
name: en*s0
• First card with a driver matching bcmgenet or smsc*:
network:
ethernets:
nic0:
match:
driver: ["bcmgenet", "smsc*"]
name: en*
• set-name (scalar)
When matching on unique properties such as path or MAC, or with additional
assumptions such as "there will only ever be one wifi device", match rules can be
written so that they only match one device. Then this property can be used to
give that device a more specific/desirable/nicer name than the default from
udev's ifnames. Any additional device that satisfies the match rules will then
fail to get renamed and keep the original kernel name (and dmesg will show an
error).
• wakeonlan (bool)
Enable wake on LAN. Off by default.
• emit-lldp (bool) – since 0.99
(networkd backend only) Whether to emit LLDP packets. Off by default.
• receive-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware offload for
checksumming of ingress network packets is enabled (disabled). When unset, the
kernel's default will be used.
• transmit-checksum-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the hardware offload for
checksumming of egress network packets is enabled (disabled). When unset, the
kernel's default will be used.
• tcp-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP Segmentation Offload
(TSO) is enabled (disabled). When unset, the kernel's default will be used.
• tcp6-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the TCP6 Segmentation Offload
(tx-tcp6-segmentation) is enabled (disabled). When unset, the kernel's default
will be used.
• generic-segmentation-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic Segmentation Offload
(GSO) is enabled (disabled). When unset, the kernel's default will be used.
• generic-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Generic Receive Offload (GRO)
is enabled (disabled). When unset, the kernel's default will be used.
• large-receive-offload (bool) – since 0.104
(networkd backend only) If set to true (false), the Large Receive Offload (LRO)
is enabled (disabled). When unset, the kernel's default will be used.
• openvswitch (mapping) – since 0.100
This provides additional configuration for the openvswitch network device. If
Open vSwitch is not available on the system, netplan treats the presence of
openvswitch configuration as an error.
Any supported network device that is declared with the openvswitch mapping (or
any bond/bridge that includes an interface with an openvswitch configuration)
will be created in openvswitch instead of the defined renderer. In the case of a
vlan definition declared the same way, netplan will create a fake VLAN bridge in
openvswitch with the requested vlan properties.
• external-ids (mapping) – since 0.100
Passed-through directly to Open vSwitch
• other-config (mapping) – since 0.100
Passed-through directly to Open vSwitch
• lacp (scalar) – since 0.100
Valid for bond interfaces. Accepts active, passive or off (the default).
• fail-mode (scalar) – since 0.100
Valid for bridge interfaces. Accepts secure or standalone (the default).
• mcast-snooping (bool) – since 0.100
Valid for bridge interfaces. False by default.
• protocols (sequence of scalars) – since 0.100
Valid for bridge interfaces or the network section. List of protocols to be
used when negotiating a connection with the controller. Accepts OpenFlow10,
OpenFlow11, OpenFlow12, OpenFlow13, OpenFlow14, and OpenFlow15.
• rstp (bool) – since 0.100
Valid for bridge interfaces. False by default.
• controller (mapping) – since 0.100
Valid for bridge interfaces. Specify an external OpenFlow controller.
• addresses (sequence of scalars)
Set the list of addresses to use for the controller targets. The syntax of
these addresses is as defined in ovs-vsctl(8). Example: addresses:
[tcp:127.0.0.1:6653, "ssl:[fe80::1234%eth0]:6653"]
• connection-mode (scalar)
Set the connection mode for the controller. Supported options are in-band
and out-of-band. The default is in-band.
• ports (sequence of sequence of scalars) – since 0.100
Open vSwitch patch ports. Each port is declared as a pair of names which can
be referenced as interfaces in dependent virtual devices (bonds, bridges).
Example:
openvswitch:
ports:
- [patch0-1, patch1-0]
• ssl (mapping) – since 0.100
Valid for global openvswitch settings. Options for configuring SSL server
endpoint for the switch.
• ca-cert (scalar)
Path to a file containing the CA certificate to be used.
• certificate (scalar)
Path to a file containing the server certificate.
• private-key (scalar)
Path to a file containing the private key for the server.
Properties for all device types
• renderer (scalar)
Use the given networking backend for this definition. Currently supported are
networkd and NetworkManager. This property can be specified globally in
network:, for a device type (in e. g. ethernets:) or for a particular device
definition. Default is networkd.
(Since 0.99) The renderer property has one additional acceptable value for vlan
objects (i. e. defined in vlans:): sriov. If a vlan is defined with the sriov
renderer for an SR-IOV Virtual Function interface, this causes netplan to set up
a hardware VLAN filter for it. There can be only one defined per VF.
• dhcp4 (bool)
Enable DHCP for IPv4. Off by default.
• dhcp6 (bool)
Enable DHCP for IPv6. Off by default. This covers both stateless DHCP - where
the DHCP server supplies information like DNS nameservers but not the IP address
- and stateful DHCP, where the server provides both the address and the other
information.
If you are in an IPv6-only environment with completely stateless auto-
configuration (SLAAC with RDNSS), this option can be set to cause the interface
to be brought up. (Setting accept-ra alone is not sufficient.) Auto-
configuration will still honor the contents of the router advertisement and only
use DHCP if requested in the RA.
Note that rdnssd(8) is required to use RDNSS with networkd. No extra software is
required for NetworkManager.
• ipv6-mtu (scalar) – since 0.98 > Set the IPv6 MTU (only supported with networkd
backend). Note > that needing to set this is an unusual requirement. > > Requires
feature: ipv6-mtu
• ipv6-privacy (bool)
Enable IPv6 Privacy Extensions (RFC 4941) for the specified interface, and prefer
temporary addresses. Defaults to false - no privacy extensions. There is
currently no way to have a private address but prefer the public address.
• link-local (sequence of scalars)
Configure the link-local addresses to bring up. Valid options are 'ipv4' and
'ipv6', which respectively allow enabling IPv4 and IPv6 link local addressing.
If this field is not defined, the default is to enable only IPv6 link-local
addresses. If the field is defined but configured as an empty set, IPv6 link-
local addresses are disabled as well as IPv4 link- local addresses.
This feature enables or disables link-local addresses for a protocol, but the
actual implementation differs per backend. On networkd, this directly changes
the behavior and may add an extra address on an interface. When using the
NetworkManager backend, enabling link-local has no effect if the interface also
has DHCP enabled.
Examples:
• Enable only IPv4 link-local: link-local: [ ipv4 ]
• Enable all link-local addresses: link-local: [ ipv4, ipv6 ]
• Disable all link-local addresses: link-local: [ ]
• ignore-carrier (bool) – since 0.104
(networkd backend only) Allow the specified interface to be configured even if it
has no carrier.
• critical (bool)
Designate the connection as "critical to the system", meaning that special care
will be taken by to not release the assigned IP when the daemon is restarted.
(not recognized by NetworkManager)
• dhcp-identifier (scalar)
(networkd backend only) Sets the source of DHCPv4 client identifier. If mac is
specified, the MAC address of the link is used. If this option is omitted, or if
duid is specified, networkd will generate an RFC4361-compliant client identifier
for the interface by combining the link's IAID and DUID.
• dhcp4-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides
section below.
• dhcp6-overrides (mapping)
(networkd backend only) Overrides default DHCP behavior; see the DHCP Overrides
section below.
• accept-ra (bool)
Accept Router Advertisement that would have the kernel configure IPv6 by itself.
When enabled, accept Router Advertisements. When disabled, do not respond to
Router Advertisements. If unset use the host kernel default setting.
• addresses (sequence of scalars and mappings)
Add static addresses to the interface in addition to the ones received through
DHCP or RA. Each sequence entry is in CIDR notation, i. e. of the form
addr/prefixlen. addr is an IPv4 or IPv6 address as recognized by inet_pton(3)
and prefixlen the number of bits of the subnet.
For virtual devices (bridges, bonds, vlan) if there is no address configured and
DHCP is disabled, the interface may still be brought online, but will not be
addressable from the network.
In addition to the addresses themselves one can specify configuration parameters
as mappings. Current supported options are:
• lifetime (scalar) – since 0.100
Default: forever. This can be forever or 0 and corresponds to the
PreferredLifetime option in systemd-networkd's Address section. Currently
supported on the networkd backend only.
• label (scalar) – since 0.100
An IP address label, equivalent to the ip address label command. Currently
supported on the networkd backend only.
Examples:
• Simple: addresses: [192.168.14.2/24, "2001:1::1/64"]
• Advanced:
network:
ethernets:
eth0:
addresses:
- "10.0.0.15/24":
lifetime: 0
label: "maas"
- "2001:1::1/64"
• ipv6-address-generation (scalar) – since 0.99
Configure method for creating the address for use with RFC4862 IPv6 Stateless
Address Auto-configuration (only supported with NetworkManager backend).
Possible values are eui64 or stable-privacy.
• ipv6-address-token (scalar) – since 0.100
Define an IPv6 address token for creating a static interface identifier for IPv6
Stateless Address Auto-configuration. This is mutually exclusive with
ipv6-address-generation.
• gateway4, gateway6 (scalar)
Deprecated, see Default routes. Set default gateway for IPv4/6, for manual
address configuration. This requires setting addresses too. Gateway IPs must be
in a form recognized by inet_pton(3). There should only be a single gateway per
IP address family set in your global config, to make it unambiguous. If you need
multiple default routes, please define them via routing-policy.
Examples
• IPv4: gateway4: 172.16.0.1
• IPv6: gateway6: "2001:4::1"
• nameservers (mapping)
Set DNS servers and search domains, for manual address configuration. There are
two supported fields: addresses: is a list of IPv4 or IPv6 addresses similar to
gateway*, and search: is a list of search domains.
Example:
network:
ethernets:
id0:
[...]
nameservers:
search: [lab, home]
addresses: [8.8.8.8, "FEDC::1"]
• macaddress (scalar)
Set the device's MAC address. The MAC address must be in the form
"XX:XX:XX:XX:XX:XX".
Note: This will not work reliably for devices matched by name only and rendered
by networkd, due to interactions with device renaming in udev. Match devices by
MAC when setting MAC addresses.
Example:
network:
ethernets:
id0:
match:
macaddress: 52:54:00:6b:3c:58
[...]
macaddress: 52:54:00:6b:3c:59
• mtu (scalar)
Set the Maximum Transmission Unit for the interface. The default is 1500. Valid
values depend on your network interface.
Note: This will not work reliably for devices matched by name only and rendered
by networkd, due to interactions with device renaming in udev. Match devices by
MAC when setting MTU.
• optional (bool)
An optional device is not required for booting. Normally, networkd will wait
some time for device to become configured before proceeding with booting.
However, if a device is marked as optional, networkd will not wait for it. This
is only supported by networkd, and the default is false.
Example:
network:
ethernets:
eth7:
# this is plugged into a test network that is often
# down - don't wait for it to come up during boot.
dhcp4: true
optional: true
• optional-addresses (sequence of scalars)
Specify types of addresses that are not required for a device to be considered
online. This changes the behavior of backends at boot time to avoid waiting for
addresses that are marked optional, and thus consider the interface as "usable"
sooner. This does not disable these addresses, which will be brought up anyway.
Example:
network:
ethernets:
eth7:
dhcp4: true
dhcp6: true
optional-addresses: [ ipv4-ll, dhcp6 ]
• activation-mode (scalar) – since 0.103
Allows specifying the management policy of the selected interface. By default,
netplan brings up any configured interface if possible. Using the activation-
mode setting users can override that behavior by either specifying manual, to
hand over control over the interface state to the administrator or (for networkd
backend only) off to force the link in a down state at all times. Any interface
with activation-mode defined is implicitly considered optional. Supported
officially as of networkd v248+.
Example:
network:
ethernets:
eth1:
# this interface will not be put into an UP state automatically
dhcp4: true
activation-mode: manual
• routes (sequence of mappings)
Configure static routing for the device; see the Routing section below.
• routing-policy (sequence of mappings)
Configure policy routing for the device; see the Routing section below.
• neigh-suppress (scalar) – since 0.105
Takes a boolean. Configures whether ARP and ND neighbor suppression is enabled
for this port. When unset, the kernel's default will be used.
DHCP Overrides
Several DHCP behavior overrides are available. Most currently only have any effect when
using the networkd backend, with the exception of use-routes and route-metric.
Overrides only have an effect if the corresponding dhcp4 or dhcp6 is set to true.
If both dhcp4 and dhcp6 are true, the networkd backend requires that dhcp4-overrides and
dhcp6-overrides contain the same keys and values. If the values do not match, an error
will be shown and the network configuration will not be applied.
When using the NetworkManager backend, different values may be specified for
dhcp4-overrides and dhcp6-overrides, and will be applied to the DHCP client processes as
specified in the netplan YAML.
• dhcp4-overrides, dhcp6-overrides (mapping)
The dhcp4-overrides and `dhcp6-override`` mappings override the default DHCP
behavior.
• use-dns (bool)
Default: true. When true, the DNS servers received from the DHCP server will
be used and take precedence over any statically configured ones. Currently
only has an effect on the networkd backend.
• use-ntp (bool)
Default: true. When true, the NTP servers received from the DHCP server will
be used by systemd-timesyncd and take precedence over any statically configured
ones. Currently only has an effect on the networkd backend.
• send-hostname (bool)
Default: true. When true, the machine's hostname will be sent to the DHCP
server. Currently only has an effect on the networkd backend.
• use-hostname (bool)
Default: true. When true, the hostname received from the DHCP server will be
set as the transient hostname of the system. Currently only has an effect on
the networkd backend.
• use-mtu (bool)
Default: true. When true, the MTU received from the DHCP server will be set as
the MTU of the network interface. When false, the MTU advertised by the DHCP
server will be ignored. Currently only has an effect on the networkd backend.
• hostname (scalar)
Use this value for the hostname which is sent to the DHCP server, instead of
machine's hostname. Currently only has an effect on the networkd backend.
• use-routes (bool)
Default: true. When true, the routes received from the DHCP server will be
installed in the routing table normally. When set to false, routes from the
DHCP server will be ignored: in this case, the user is responsible for adding
static routes if necessary for correct network operation. This allows users to
avoid installing a default gateway for interfaces configured via DHCP.
Available for both the networkd and NetworkManager backends.
• route-metric (scalar)
Use this value for default metric for automatically-added routes. Use this to
prioritize routes for devices by setting a lower metric on a preferred
interface. Available for both the networkd and NetworkManager backends.
• use-domains (scalar) – since 0.98
Takes a boolean, or the special value "route". When true, the domain name
received from the DHCP server will be used as DNS search domain over this link,
similar to the effect of the Domains= setting. If set to "route", the domain
name received from the DHCP server will be used for routing DNS queries only,
but not for searching, similar to the effect of the Domains= setting when the
argument is prefixed with "~".
Requires feature: dhcp-use-domains
Routing
Complex routing is possible with netplan. Standard static routes as well as policy
routing using routing tables are supported via the networkd backend.
These options are available for all types of interfaces.
Default routes
The most common need for routing concerns the definition of default routes to reach the
wider Internet. Those default routes can only defined once per IP family and routing
table. A typical example would look like the following:
network:
ethernets:
eth0:
[...]
routes:
- to: default # could be 0.0.0.0/0 optionally
via: 10.0.0.1
metric: 100
on-link: true
- to: default # could be ::/0 optionally
via: cf02:de:ad:be:ef::2
eth1:
[...]
routes:
- to: default
via: 172.134.67.1
metric: 100
on-link: true
# Not on the main routing table,
# does not conflict with the eth0 default route
table: 76
• routes (mapping)
The routes block defines standard static routes for an interface. At least to
must be specified. If type is local or nat a default scope of host is assumed.
If type is unicast and no gateway (via) is given or type is broadcast, multicast
or anycast a default scope of link is assumed. Otherwise, a global scope is the
default setting.
For from, to, and via, both IPv4 and IPv6 addresses are recognized, and must be
in the form addr/prefixlen or addr.
• from (scalar)
Set a source IP address for traffic going through the route. (NetworkManager:
as of v1.8.0)
• to (scalar)
Destination address for the route.
• via (scalar)
Address to the gateway to use for this route.
• on-link (bool)
When set to "true", specifies that the route is directly connected to the
interface. (NetworkManager: as of v1.12.0 for IPv4 and v1.18.0 for IPv6)
• metric (scalar)
The relative priority of the route. Must be a positive integer value.
• type (scalar)
The type of route. Valid options are "unicast" (default), "anycast",
"blackhole", "broadcast", "local", "multicast", "nat", "prohibit", "throw",
"unreachable" or "xresolve".
• scope (scalar)
The route scope, how wide-ranging it is to the network. Possible values are
"global", "link", or "host". Applies to IPv4 only.
• table (scalar)
The table number to use for the route. In some scenarios, it may be useful to
set routes in a separate routing table. It may also be used to refer to
routing policy rules which also accept a table parameter. Allowed values are
positive integers starting from 1. Some values are already in use to refer to
specific routing tables: see /etc/iproute2/rt_tables. (NetworkManager: as of
v1.10.0)
• mtu (scalar) – since 0.101
The MTU to be used for the route, in bytes. Must be a positive integer value.
• congestion-window (scalar) – since 0.102
The congestion window to be used for the route, represented by number of
segments. Must be a positive integer value.
• advertised-receive-window (scalar) – since 0.102
The receive window to be advertised for the route, represented by number of
segments. Must be a positive integer value.
• routing-policy (mapping)
The routing-policy block defines extra routing policy for a network, where
traffic may be handled specially based on the source IP, firewall marking, etc.
For from, to, both IPv4 and IPv6 addresses are recognized, and must be in the
form addr/prefixlen or addr.
• from (scalar)
Set a source IP address to match traffic for this policy rule.
• to (scalar)
Match on traffic going to the specified destination.
• table (scalar)
The table number to match for the route. In some scenarios, it may be useful
to set routes in a separate routing table. It may also be used to refer to
routes which also accept a table parameter. Allowed values are positive
integers starting from 1. Some values are already in use to refer to specific
routing tables: see /etc/iproute2/rt_tables.
• priority (scalar)
Specify a priority for the routing policy rule, to influence the order in which
routing rules are processed. A higher number means lower priority: rules are
processed in order by increasing priority number.
• mark (scalar)
Have this routing policy rule match on traffic that has been marked by the
iptables firewall with this value. Allowed values are positive integers
starting from 1.
• type-of-service (scalar)
Match this policy rule based on the type of service number applied to the
traffic.
Authentication
Netplan supports advanced authentication settings for ethernet and wifi interfaces, as
well as individual wifi networks, by means of the auth block.
• auth (mapping)
Specifies authentication settings for a device of type ethernets:, or an access-
points: entry on a wifis: device.
The auth block supports the following properties:
• key-management (scalar)
The supported key management modes are none (no key management); psk (WPA with
pre-shared key, common for home wifi); eap (WPA with EAP, common for enterprise
wifi); sae (used by WPA3); and 802.1x (used primarily for wired Ethernet
connections).
• password (scalar)
The password string for EAP, or the pre-shared key for WPA-PSK.
The following properties can be used if key-management is eap or 802.1x:
• method (scalar)
The EAP method to use. The supported EAP methods are tls (TLS), peap
(Protected EAP), leap (Lightweight EAP), pwd (EAP Password) and ttls (Tunneled
TLS).
• identity (scalar)
The identity to use for EAP.
• anonymous-identity (scalar)
The identity to pass over the unencrypted channel if the chosen EAP method
supports passing a different tunnelled identity.
• ca-certificate (scalar)
Path to a file with one or more trusted certificate authority (CA)
certificates.
• client-certificate (scalar)
Path to a file containing the certificate to be used by the client during
authentication.
• client-key (scalar)
Path to a file containing the private key corresponding to client-certificate.
• client-key-password (scalar)
Password to use to decrypt the private key specified in client-key if it is
encrypted.
• phase2-auth (scalar) – since 0.99
Phase 2 authentication mechanism.
Properties for device type ethernets:
Status: Optional.
Purpose: Use the ethernets key to configure Ethernet interfaces.
Structure: The key consists of a mapping of Ethernet interface IDs. Each ethernet has a
number of configuration options. You don't need to define each interface by their name
inside the ethernets mapping. You can use any ID that describes the interface and match
the actual network card using the match key. The general configuration structure for
Ethernets is shown below.
network:
ethernets:
device-id:
...
device-id is the interface identifier. If you use the interface name as the ID, Netplan
will match that interface.
Consider the example below. In this case, an interface called eth0 will be configured
with DHCP.
network:
ethernets:
eth0:
dhcp4: true
The device-id can be any descriptive name your find meaningful. Although, if it doesn't
match a real interface name, you must use the property match to identify the device you
want to configure.
The example below defines an Ethernet connection called isp-interface (supposedly an
external interface connected to the Internet Service Provider) and uses match to apply the
configuration to the physical device with MAC address aa:bb:cc:00:11:22.
network:
ethernets:
isp-interface:
match:
macaddress: aa:bb:cc:00:11:22
dhcp4: true
Ethernet device definitions, beyond common ones described above, also support some
additional properties that can be used for SR-IOV devices.
• link (scalar) – since 0.99
(SR-IOV devices only) The link property declares the device as a Virtual Function
of the selected Physical Function device, as identified by the given netplan id.
Example:
network:
ethernets:
enp1: {...}
enp1s16f1:
link: enp1
• virtual-function-count (scalar) – since 0.99
(SR-IOV devices only) In certain special cases VFs might need to be configured
outside of netplan. For such configurations virtual-function-count can be
optionally used to set an explicit number of Virtual Functions for the given
Physical Function. If unset, the default is to create only as many VFs as are
defined in the netplan configuration. This should be used for special cases
only.
Requires feature: sriov
• embedded-switch-mode (scalar) – since 0.104
(SR-IOV devices only) Change the operational mode of the embedded switch of a
supported SmartNIC PCI device (e.g. Mellanox ConnectX-5). Possible values are
switchdev or legacy, if unspecified the vendor's default configuration is used.
Requires feature: eswitch-mode
• delay-virtual-functions-rebind (bool) – since 0.104
(SR-IOV devices only) Delay rebinding of SR-IOV virtual functions to its driver
after changing the embedded-switch-mode setting to a later stage. Can be enabled
when bonding/VF LAG is in use. Defaults to false.
Requires feature: eswitch-mode
• infiniband-mode (scalar) – since 0.105
(InfiniBand devices only) Change the operational mode of a IPoIB device.
Possible values are datagram or connected. If unspecified the kernel's default
configuration is used.
Requires feature: infiniband
Properties for device type modems:
Status: Optional.
Purpose: Use the modems key to configure Modem interfaces. GSM/CDMA modem configuration
is only supported for the NetworkManager backend. systemd-networkd does not support
modems.
Structure: The key consists of a mapping of Modem IDs. Each modem has a number of
configuration options. The general configuration structure for Modems is shown below.
network:
version: 2
renderer: NetworkManager
modems:
cdc-wdm1:
mtu: 1600
apn: ISP.CINGULAR
username: ISP@CINGULARGPRS.COM
password: CINGULAR1
number: "*99#"
network-id: 24005
device-id: da812de91eec16620b06cd0ca5cbc7ea25245222
pin: 2345
sim-id: 89148000000060671234
sim-operator-id: 310260
Requires feature: modems
• apn (scalar) – since 0.99
Set the carrier APN (Access Point Name). This can be omitted if auto-config is
enabled.
• auto-config (bool) – since 0.99
Specify whether to try and auto-configure the modem by doing a lookup of the
carrier against the Mobile Broadband Provider database. This may not work for
all carriers.
• device-id (scalar) – since 0.99
Specify the device ID (as given by the WWAN management service) of the modem to
match. This can be found using mmcli.
• network-id (scalar) – since 0.99
Specify the Network ID (GSM LAI format). If this is specified, the device will
not roam networks.
• number (scalar) – since 0.99
The number to dial to establish the connection to the mobile broadband network.
(Deprecated for GSM)
• password (scalar) – since 0.99
Specify the password used to authenticate with the carrier network. This can be
omitted if auto-config is enabled.
• pin (scalar) – since 0.99
Specify the SIM PIN to allow it to operate if a PIN is set.
• sim-id (scalar) – since 0.99
Specify the SIM unique identifier (as given by the WWAN management service) which
this connection applies to. If given, the connection will apply to any device
also allowed by device-id which contains a SIM card matching the given
identifier.
• sim-operator-id (scalar) – since 0.99
Specify the MCC/MNC string (such as "310260" or "21601") which identifies the
carrier that this connection should apply to. If given, the connection will
apply to any device also allowed by device-id and sim-id which contains a SIM
card provisioned by the given operator.
• username (scalar) – since 0.99
Specify the username used to authenticate with the carrier network. This can be
omitted if auto-config is enabled.
Properties for device type wifis:
Status: Optional.
Purpose: Use the wifis key to configure WiFi access points.
Structure: The key consists of a mapping of WiFi IDs. Each wifi has a number of
configuration options. The general configuration structure for WiFis is shown below.
network:
version: 2
wifis:
wlp0s1:
access-points:
"network_ssid_name":
password: "**********"
Note that systemd-networkd does not natively support wifi, so you need wpasupplicant
installed if you let the networkd renderer handle wifi.
• access-points (mapping)
This provides pre-configured connections to NetworkManager. Note that users can
of course select other access points/SSIDs. The keys of the mapping are the
SSIDs, and the values are mappings with the following supported properties:
• password (scalar)
Enable WPA/WPA2 authentication and set the passphrase for it. If neither this
nor an auth block are given, the network is assumed to be open. The setting
password: "S3kr1t"
is equivalent to
auth:
key-management: psk
password: "S3kr1t"
• mode (scalar)
Possible access point modes are infrastructure (the default), ap (create an
access point to which other devices can connect), and adhoc (peer to peer
networks without a central access point). ap is only supported with
NetworkManager.
• bssid (scalar) – since 0.99
If specified, directs the device to only associate with the given access point.
• band (scalar) – since 0.99
Possible bands are 5GHz (for 5GHz 802.11a) and 2.4GHz (for 2.4GHz 802.11), do
not restrict the 802.11 frequency band of the network if unset (the default).
• channel (scalar) – since 0.99
Wireless channel to use for the Wi-Fi connection. Because channel numbers
overlap between bands, this property takes effect only if the band property is
also set.
• hidden (bool) – since 0.100
Set to true to change the SSID scan technique for connecting to hidden WiFi
networks. Note this may have slower performance compared to false (the
default) when connecting to publicly broadcast SSIDs.
• wakeonwlan (sequence of scalars) – since 0.99
This enables WakeOnWLan on supported devices. Not all drivers support all
options. May be any combination of any, disconnect, magic_pkt,
gtk_rekey_failure, eap_identity_req, four_way_handshake, rfkill_release or tcp
(NetworkManager only). Or the exclusive default flag (the default).
• regulatory-domain (scalar) – since 0.105
This can be used to define the radio's regulatory domain, to make use of
additional WiFi channels outside the "world domain". Takes an ISO / IEC 3166
country code (like GB) or 00 to reset to the "world domain". See wireless-regdb
(https://git.kernel.org/pub/scm/linux/kernel/git/sforshee/wireless-
regdb.git/tree/db.txt) for available values.
Requires dependency: iw, if it is to be used outside the networkd
(wpa_supplicant) backend.
Properties for device type bridges:
Status: Optional.
Purpose: Use the bridges key to create Bridge interfaces.
Structure: The key consists of a mapping of Bridge interface names. Each bridge has an
optional list of interfaces that will be bridged together. The interfaces listed in the
interfaces key (enp5s0 and enp5s1 below) must also be defined in your Netplan
configuration. The general configuration structure for Bridges is shown below.
network:
bridges:
br0:
interfaces:
- enp5s0
- enp5s1
dhcp4: true
...
When applied, a virtual interface of type bridge called br0 will be created in the system.
The specific settings for bridges are defined below.
• interfaces (sequence of scalars)
All devices matching this ID list will be added to the bridge. This may be an
empty list, in which case the bridge will be brought online with no member
interfaces.
Example:
network:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bridges:
br0:
interfaces: [switchports]
• parameters (mapping)
Customization parameters for special bridging options. Time intervals may need
to be expressed as a number of seconds or milliseconds: the default value type is
specified below. If necessary, time intervals can be qualified using a time
suffix (such as "s" for seconds, "ms" for milliseconds) to allow for more control
over its behavior.
• ageing-time, aging-time (scalar)
Set the period of time to keep a MAC address in the forwarding database after a
packet is received. This maps to the AgeingTimeSec= property when the networkd
renderer is used. If no time suffix is specified, the value will be
interpreted as seconds.
• priority (scalar)
Set the priority value for the bridge. This value should be a number between 0
and 65535. Lower values mean higher priority. The bridge with the higher
priority will be elected as the root bridge.
• port-priority (mapping)
Set the port priority per interface. The priority value is a number between 0
and 63. This metric is used in the designated port and root port selection
algorithms.
Example:
network:
ethernets:
eth0:
dhcp4: false
eth1:
dhcp4: false
bridges:
br0:
interfaces: [eth0, eth1]
parameters:
port-priority:
eth0: 10
eth1: 20
• forward-delay (scalar)
Specify the period of time the bridge will remain in Listening and Learning
states before getting to the Forwarding state. This field maps to the
ForwardDelaySec= property for the networkd renderer. If no time suffix is
specified, the value will be interpreted as seconds.
• hello-time (scalar)
Specify the interval between two hello packets being sent out from the root and
designated bridges. Hello packets communicate information about the network
topology. When the networkd renderer is used, this maps to the HelloTimeSec=
property. If no time suffix is specified, the value will be interpreted as
seconds.
• max-age (scalar)
Set the maximum age of a hello packet. If the last hello packet is older than
that value, the bridge will attempt to become the root bridge. This maps to
the MaxAgeSec= property when the networkd renderer is used. If no time suffix
is specified, the value will be interpreted as seconds.
• path-cost (mapping)
Set the per-interface cost of a path on the bridge. Faster interfaces should
have a lower cost. This allows a finer control on the network topology so that
the fastest paths are available whenever possible.
Example:
network:
ethernets:
eth0:
dhcp4: false
eth1:
dhcp4: false
bridges:
br0:
interfaces: [eth0, eth1]
parameters:
path-cost:
eth0: 100
eth1: 200
• stp (bool)
Define whether the bridge should use Spanning Tree Protocol. The default value
is "true", which means that Spanning Tree should be used.
Properties for device type dummy-devices:
Status: Optional.
Purpose: Use the dummy-devices key to create virtual interfaces.
Structure: The key consists of a mapping of interface names. Dummy devices are virtual
devices that can be used to route packets to without actually transmitting them.
network:
dummy-devices:
dm0:
addresses:
- 192.168.0.123/24
...
When applied, a virtual interface called dm0 will be created in the system.
See the "Properties for all device types" section for the list of properties that can be
used with this type of interface.
Properties for device type bonds:
Status: Optional.
Purpose: Use the bonds key to create Bond (Link Aggregation) interfaces.
Structure: The key consists of a mapping of Bond interface names. Each bond has an
optional list of interfaces that will be part of the aggregation. The interfaces listed
in the interfaces key must also be defined in your Netplan configuration. The general
configuration structure for Bonds is shown below.
network:
bonds:
bond0:
interfaces:
- enp5s0
- enp5s1
- enp5s2
mode: active-backup
...
When applied, a virtual interface of type bond called bond0 will be created in the system.
The specific settings for bonds are defined below.
• interfaces (sequence of scalars)
All devices matching this ID list will be added to the bond.
Example:
network:
ethernets:
switchports:
match: {name: "enp2*"}
[...]
bonds:
bond0:
interfaces: [switchports]
• parameters (mapping)
Customization parameters for special bonding options. Time intervals may need to
be expressed as a number of seconds or milliseconds: the default value type is
specified below. If necessary, time intervals can be qualified using a time
suffix (such as "s" for seconds, "ms" for milliseconds) to allow for more control
over its behavior.
• mode (scalar)
Set the bonding mode used for the interfaces. The default is balance-rr (round
robin). Possible values are balance-rr, active-backup, balance-xor, broadcast,
802.3ad, balance-tlb, and balance-alb. For Open vSwitch active-backup and the
additional modes balance-tcp and balance-slb are supported.
• lacp-rate (scalar)
Set the rate at which LACPDUs are transmitted. This is only useful in 802.3ad
mode. Possible values are slow (30 seconds, default), and fast (every second).
• mii-monitor-interval (scalar)
Specifies the interval for MII monitoring (verifying if an interface of the
bond has carrier). The default is 0; which disables MII monitoring. This is
equivalent to the MIIMonitorSec= field for the networkd backend. If no time
suffix is specified, the value will be interpreted as milliseconds.
• min-links (scalar)
The minimum number of links up in a bond to consider the bond interface to be
up.
• transmit-hash-policy (scalar)
Specifies the transmit hash policy for the selection of ports. This is only
useful in balance-xor, 802.3ad and balance-tlb modes. Possible values are
layer2, layer3+4, layer2+3, encap2+3, and encap3+4.
• ad-select (scalar)
Set the aggregation selection mode. Possible values are stable, bandwidth, and
count. This option is only used in 802.3ad mode.
• all-members-active (bool) – since 0.106
If the bond should drop duplicate frames received on inactive ports, set this
option to false. If they should be delivered, set this option to true. The
default value is false, and is the desirable behavior in most situations.
Alias: all-slaves-active
• arp-interval (scalar)
Set the interval value for how frequently ARP link monitoring should happen.
The default value is 0, which disables ARP monitoring. For the networkd
backend, this maps to the ARPIntervalSec= property. If no time suffix is
specified, the value will be interpreted as milliseconds.
• arp-ip-targets (sequence of scalars)
IPs of other hosts on the link which should be sent ARP requests in order to
validate that a port is up. This option is only used when arp-interval is set
to a value other than 0. At least one IP address must be given for ARP link
monitoring to function. Only IPv4 addresses are supported. You can specify up
to 16 IP addresses. The default value is an empty list.
• arp-validate (scalar)
Configure how ARP replies are to be validated when using ARP link monitoring.
Possible values are none, active, backup, and all.
• arp-all-targets (scalar)
Specify whether to use any ARP IP target being up as sufficient for a port to
be considered up; or if all the targets must be up. This is only used for
active-backup mode when arp-validate is enabled. Possible values are any and
all.
• up-delay (scalar)
Specify the delay before enabling a link once the link is physically up. The
default value is 0. This maps to the UpDelaySec= property for the networkd
renderer. This option is only valid for the miimon link monitor. If no time
suffix is specified, the value will be interpreted as milliseconds.
• down-delay (scalar)
Specify the delay before disabling a link once the link has been lost. The
default value is 0. This maps to the DownDelaySec= property for the networkd
renderer. This option is only valid for the miimon link monitor. If no time
suffix is specified, the value will be interpreted as milliseconds.
• fail-over-mac-policy (scalar)
Set whether to set all ports to the same MAC address when adding them to the
bond, or how else the system should handle MAC addresses. The possible values
are none, active, and follow.
• gratuitous-arp (scalar)
Specify how many ARP packets to send after failover. Once a link is up on a
new port, a notification is sent and possibly repeated if this value is set to
a number greater than 1. The default value is 1 and valid values are between 1
and 255. This only affects active-backup mode.
For historical reasons, the misspelling gratuitious-arp is also accepted and
has the same function.
• packets-per-member (scalar) – since 0.106
In balance-rr mode, specifies the number of packets to transmit on a port
before switching to the next. When this value is set to 0, ports are chosen at
random. Allowable values are between 0 and 65535. The default value is 1.
This setting is only used in balance-rr mode.
Alias: packets-per-slave
• primary-reselect-policy (scalar)
Set the reselection policy for the primary port. On failure of the active
port, the system will use this policy to decide how the new active port will be
chosen and how recovery will be handled. The possible values are always,
better, and failure.
• resend-igmp (scalar)
In modes balance-rr, active-backup, balance-tlb and balance-alb, a failover can
switch IGMP traffic from one port to another.
This parameter specifies how many IGMP membership reports are issued on a
failover event. Values range from 0 to 255. 0 disables sending membership
reports. Otherwise, the first membership report is sent on failover and
subsequent reports are sent at 200ms intervals.
• learn-packet-interval (scalar)
Specify the interval between sending learning packets to each port. The value
range is between 1 and 0x7fffffff. The default value is 1. This option only
affects balance-tlb and balance-alb modes. Using the networkd renderer, this
field maps to the LearnPacketIntervalSec= property. If no time suffix is
specified, the value will be interpreted as seconds.
• primary (scalar)
Specify a device to be used as a primary port, or preferred device to use as a
port for the bond (i.e. the preferred device to send data through), whenever
it is available. This only affects active-backup, balance-alb, and balance-tlb
modes.
Properties for device type tunnels:
Status: Optional.
Purpose: Use the tunnels key to create virtual tunnel interfaces.
Structure: The key consists of a mapping of tunnel interface names. Each tunnel requires
the identification of the tunnel mode (see the section mode below for the list of
supported modes). The general configuration structure for Tunnels is shown below.
network:
tunnels:
tunnel0:
mode: SCALAR
...
When applied, a virtual interface called tunnel0 will be created in the system. Its
operation mode is defined by the property mode.
Tunnels allow traffic to pass as if it was between systems on the same local network,
although systems may be far from each other but reachable via the Internet. They may be
used to support IPv6 traffic on a network where the ISP does not provide the service, or
to extend and "connect" separate local networks. Please see
<https://en.wikipedia.org/wiki/Tunneling_protocol> for more general information about
tunnels.
The specific settings for tunnels are defined below.
• mode (scalar)
Defines the tunnel mode. Valid options are sit, gre, ip6gre, ipip, ipip6,
ip6ip6, vti, vti6, wireguard, vxlan, gretap and ip6gretap modes. In addition,
the NetworkManager backend supports isatap tunnels.
• local (scalar)
Defines the address of the local endpoint of the tunnel. (For VXLAN) This should
match one of the parent's IP addresses or make use of the networkd special
values.
• remote (scalar)
Defines the address of the remote endpoint of the tunnel or multicast group IP
address for VXLAN.
• ttl (scalar) – since 0.103
Defines the Time To Live (TTL) of the tunnel. Takes a number in the range
1..255.
• key (scalar or mapping)
Define keys to use for the tunnel. The key can be a number or a dotted quad (an
IPv4 address). For wireguard it can be a base64-encoded private key or (as of
networkd v242+) an absolute path to a file, containing the private key (since
0.100). It is used for identification of IP transforms. This is only required
for vti and vti6 when using the networkd backend.
This field may be used as a scalar (meaning that a single key is specified and to
be used for input, output and private key), or as a mapping, where you can
further specify input/output/private.
• input (scalar)
The input key for the tunnel
• output (scalar)
The output key for the tunnel
• private (scalar) – since 0.100
A base64-encoded private key required for WireGuard tunnels. When the systemd-
networkd backend (v242+) is used, this can also be an absolute path to a file
containing the private key.
• private-key-flags (sequence of scalars) – since 0.107
Private key flags used by Network Manager. Possible values are: agent-owned,
not-saved and not-required.
agent-owned: a user-session secret agent is responsible for providing and
storing this secret.
not-saved: this secret should not be saved but should be requested from the
user each time it is required.
not-required: this flag hints that the secret is not required and should not be
requested from the user.
Example:
network:
renderer: NetworkManager
tunnels:
wg0:
mode: wireguard
port: 5182
key:
private-key-flags:
- agent-owned
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
keepalive: 23
endpoint: 1.2.3.4:5
• keys (scalar or mapping)
Alternate name for the key field. See above.
Examples:
network:
tunnels:
tun0:
mode: gre
local: ...
remote: ...
keys:
input: 1234
output: 5678
network:
tunnels:
tun0:
mode: vti6
local: ...
remote: ...
key: 59568549
network:
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
shared: /path/to/shared.key
...
key: mNb7OIIXTdgW4khM7OFlzJ+UPs7lmcWHV7xjPgakMkQ=
network:
tunnels:
wg0:
mode: wireguard
addresses: [...]
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
...
keys:
private: /path/to/priv.key
WireGuard specific keys:
• mark (scalar) – since 0.100
Firewall mark for outgoing WireGuard packets from this interface, optional.
• port (scalar) – since 0.100
UDP port to listen at or auto. Optional, defaults to auto.
• peers (sequence of mappings) – since 0.100
A list of peers, each having keys documented below.
Example:
network:
tunnels:
wg0:
mode: wireguard
key: /path/to/private.key
mark: 42
port: 5182
peers:
- keys:
public: rlbInAj0qV69CysWPQY7KEBnKxpYCpaWqOs/dLevdWc=
allowed-ips: [0.0.0.0/0, "2001:fe:ad:de:ad:be:ef:1/24"]
keepalive: 23
endpoint: 1.2.3.4:5
- keys:
public: M9nt4YujIOmNrRmpIRTmYSfMdrpvE7u6WkG8FY8WjG4=
shared: /some/shared.key
allowed-ips: [10.10.10.20/24]
keepalive: 22
endpoint: 5.4.3.2:1
• endpoint (scalar) – since 0.100
Remote endpoint IPv4/IPv6 address or a hostname, followed by a colon and a port
number.
• allowed-ips (sequence of scalars) – since 0.100
A list of IP (v4 or v6) addresses with CIDR masks from which this peer is
allowed to send incoming traffic and to which outgoing traffic for this peer is
directed. The catch-all 0.0.0.0/0 may be specified for matching all IPv4
addresses, and ::/0 may be specified for matching all IPv6 addresses.
• keepalive (scalar) – since 0.100
An interval in seconds, between 1 and 65535 inclusive, of how often to send an
authenticated empty packet to the peer for the purpose of keeping a stateful
firewall or NAT mapping valid persistently. Optional.
• keys (mapping) – since 0.100
Define keys to use for the WireGuard peers.
This field can be used as a mapping, where you can further specify the public
and shared keys.
• public (scalar) – since 0.100
A base64-encoded public key, required for WireGuard peers.
• shared (scalar) – since 0.100
A base64-encoded preshared key. Optional for WireGuard peers. When the
systemd-networkd backend (v242+) is used, this can also be an absolute path
to a file containing the preshared key.
VXLAN specific keys:
• id (scalar) – since 0.105
The VXLAN Network Identifier (VNI or VXLAN Segment ID). Takes a number in the
range 1..16777215.
• link (scalar) – since 0.105
netplan ID of the parent device definition to which this VXLAN gets connected.
• type-of-service (scalar) – since 0.105
The Type Of Service byte value for a vxlan interface.
• mac-learning (scalar) – since 0.105
Takes a boolean. When true, enables dynamic MAC learning to discover remote MAC
addresses.
• ageing, aging (scalar) – since 0.105
The lifetime of Forwarding Database entry learned by the kernel, in seconds.
• limit (scalar) – since 0.105
Configures maximum number of FDB entries.
• arp-proxy (scalar) – since 0.105
Takes a boolean. When true, bridge-connected VXLAN tunnel endpoint answers ARP
requests from the local bridge on behalf of remote Distributed Overlay Virtual
Ethernet (DOVE) clients. Defaults to false.
• notifications (sequence of scalars) – since 0.105
Takes the flags l2-miss and l3-miss to enable netlink LLADDR and/or netlink IP
address miss notifications.
• short-circuit (scalar) – since 0.105
Takes a boolean. When true, route short circuiting is turned on.
• checksums (sequence of scalars) – since 0.105
Takes the flags udp, zero-udp6-tx, zero-udp6-rx, remote-tx and remote-rx to
enable transmitting UDP checksums in VXLAN/IPv4, send/receive zero checksums in
VXLAN/IPv6 and enable sending/receiving checksum offloading in VXLAN.
• extensions (sequence of scalars) – since 0.105
Takes the flags group-policy and generic-protocol to enable the "Group Policy"
and/or "Generic Protocol" VXLAN extensions.
• port (scalar) – since 0.105
Configures the default destination UDP port. If the destination port is not
specified then Linux kernel default will be used. Set to 4789 to get the IANA
assigned value.
• port-range (sequence of scalars) – since 0.105
Configures the source port range for the VXLAN. The kernel assigns the source
UDP port based on the flow to help the receiver to do load balancing. When this
option is not set, the normal range of local UDP ports is used. Uses the form
[LOWER, UPPER].
• flow-label (scalar) – since 0.105
Specifies the flow label to use in outgoing packets. The valid range is
0-1048575.
• do-not-fragment (scalar) – since 0.105
Allows setting the IPv4 Do not Fragment (DF) bit in outgoing packets. Takes a
boolean value. When unset, the kernel's default will be used.
Properties for device type virtual-ethernets:
Status: Optional.
Purpose: Use the virtual-ethernets key to create virtual Ethernet interfaces.
Structure: The key consists of a mapping of virtual-ethernet interface names. Each
virtual-ethernet requires a peer. In order to have a fully working virtual-ethernet pair,
both devices must be defined, i.e., only setting the peer key with the peer name is not
enough, the peer interface must also be defined and set the first one as its peer. The
general configuration structure for Virtual Ethernets is shown below.
network:
virtual-ethernets:
veth0:
peer: veth1
veth1:
peer: veth0
When applied, two virtual interfaces called veth0 and veth1 will be created in the system.
Virtual Ethernets acts as tunnels forwarding traffic from one interface to the other.
They can be used to connect two separate virtual networks such as network namespaces and
bridges. It's not possible to move virtual-ethernets to different namespaces through
Netplan at the present moment.
The specific settings for virtual-ethernets are defined below.
• peer (scalar)
Defines the virtual-ethernet peer. The peer interface must also be a virtual-
ethernet device.
Below is a complete example that uses a pair of virtual Ethernet devices to create a link
between two bridges:
network:
version: 2
renderer: networkd
virtual-ethernets:
veth0-peer1:
peer: veth0-peer2
veth0-peer2:
peer: veth0-peer1
bridges:
br0:
interfaces:
- veth0-peer1
br1:
interfaces:
- veth0-peer2
Properties for device type vlans:
Status: Optional.
Purpose: Use the vlans key to create VLAN interfaces.
Structure: The key consists of a mapping of VLAN interface names. The interface used in
the link option (enp5s0 in the example below) must also be defined in the Netplan
configuration. The general configuration structure for Vlans is shown below.
network:
vlans:
vlan123:
id: 123
link: enp5s0
dhcp4: yes
The specific settings for VLANs are defined below.
• id (scalar)
VLAN ID, a number between 0 and 4094.
• link (scalar)
netplan ID of the underlying device definition on which this VLAN gets created.
Example:
network:
ethernets:
eno1: {...}
vlans:
en-intra:
id: 1
link: eno1
dhcp4: yes
en-vpn:
id: 2
link: eno1
addresses: [...]
Properties for device type vrfs:
Status: Optional.
Purpose: Use the vrfs key to create Virtual Routing and Forwarding (VRF) interfaces.
Structure: The key consists of a mapping of VRF interface names. The interface used in
the link option (enp5s0 in the example below) must also be defined in the Netplan
configuration. The general configuration structure for VRFs is shown below.
network:
renderer: networkd
vrfs:
vrf1:
table: 1
interfaces:
- enp5s0
routes:
- to: default
via: 10.10.10.4
routing-policy:
- from: 10.10.10.42
• table (scalar) – since 0.105
The numeric routing table identifier. This setting is compulsory.
• interfaces (sequence of scalars) – since 0.105
All devices matching this ID list will be added to the VRF. This may be an empty
list, in which case the VRF will be brought online with no member interfaces.
• routes (sequence of mappings) – since 0.105
Configure static routing for the device; see the Routing section. The table
value is implicitly set to the VRF's table.
• routing-policy (sequence of mappings) – since 0.105
Configure policy routing for the device; see the Routing section. The table
value is implicitly set to the VRF's table.
Example:
network:
vrfs:
vrf20:
table: 20
interfaces: [ br0 ]
routes:
- to: default
via: 10.10.10.3
routing-policy:
- from: 10.10.10.42
[...]
bridges:
br0:
interfaces: []
Properties for device type nm-devices:
Status: Optional. Its use is not recommended.
Purpose: Use the nm-devices key to configure device types that are not supported by
Netplan. This is NetworkManager specific configuration.
Structure: The key consists of a mapping of NetworkManager connections. The nm-devices
device type is for internal use only and should not be used in normal configuration files.
It enables a fallback mode for unsupported settings, using the passthrough mapping. The
general configuration structure for NM connections is shown below.
network:
version: 2
nm-devices:
NM-db5f0f67-1f4c-4d59-8ab8-3d278389cf87:
renderer: NetworkManager
networkmanager:
uuid: "db5f0f67-1f4c-4d59-8ab8-3d278389cf87"
name: "myvpnconnection"
passthrough:
connection.type: "vpn"
vpn.ca: "path to ca.crt"
vpn.cert: "path to client.crt"
vpn.cipher: "AES-256-GCM"
vpn.connection-type: "tls"
vpn.dev: "tun"
vpn.key: "path to client.key"
vpn.remote: "1.2.3.4:1194"
vpn.service-type: "org.freedesktop.NetworkManager.openvpn"
Backend-specific configuration parameters
In addition to the other fields available to configure interfaces, some backends may
require to record some of their own parameters in netplan, especially if the netplan
definitions are generated automatically by the consumer of that backend. Currently, this
is only used with NetworkManager.
• networkmanager (mapping) – since 0.99
Keeps the NetworkManager-specific configuration parameters used by the daemon to
recognize connections.
• name (scalar) – since 0.99
Set the display name for the connection.
• uuid (scalar) – since 0.99
Defines the UUID (unique identifier) for this connection, as generated by
NetworkManager itself.
• stable-id (scalar) – since 0.99
Defines the stable ID (a different form of a connection name) used by
NetworkManager in case the name of the connection might otherwise change, such
as when sharing connections between users.
• device (scalar) – since 0.99
Defines the interface name for which this connection applies.
• passthrough (mapping) – since 0.102
Can be used as a fallback mechanism to missing keyfile settings.
SEE ALSO
netplan-generate(8), netplan-apply(8), netplan-try(8), netplan-get(8), netplan-set(8),
netplan-info(8), netplan-ip(8), netplan-rebind(8), netplan-status(8), netplan-dbus(8),
systemd-networkd(8), NetworkManager(8)
AUTHORS
Mathieu Trudel-Lapierre (<cyphermox@ubuntu.com>); Martin Pitt (<martin.pitt@ubuntu.com>);
Lukas Märdian (<slyon@ubuntu.com>).
YAML configuration(5)