Provided by: busybox-static_1.36.1-3ubuntu1_amd64 bug

NAME

       BusyBox - The Swiss Army Knife of Embedded Linux

SYNTAX

        busybox <applet> [arguments...]  # or

        <applet> [arguments...]          # if symlinked

DESCRIPTION

       BusyBox combines tiny versions of many common UNIX utilities into a single small
       executable. It provides minimalist replacements for most of the utilities you usually find
       in GNU coreutils, util-linux, etc. The utilities in BusyBox generally have fewer options
       than their full-featured GNU cousins; however, the options that are included provide the
       expected functionality and behave very much like their GNU counterparts.

       BusyBox has been written with size-optimization and limited resources in mind.  It is also
       extremely modular so you can easily include or exclude commands (or features) at compile
       time. This makes it easy to customize your embedded systems. To create a working system,
       just add /dev, /etc, and a Linux kernel.  BusyBox provides a fairly complete POSIX
       environment for any small or embedded system.

       BusyBox is extremely configurable.  This allows you to include only the components you
       need, thereby reducing binary size. Run 'make config' or 'make menuconfig' to select the
       functionality that you wish to enable.  Then run 'make' to compile BusyBox using your
       configuration.

       After the compile has finished, you should use 'make install' to install BusyBox. This
       will install the 'bin/busybox' binary, in the target directory specified by CONFIG_PREFIX.
       CONFIG_PREFIX can be set when configuring BusyBox, or you can specify an alternative
       location at install time (i.e., with a command line like 'make CONFIG_PREFIX=/tmp/foo
       install'). If you enabled any applet installation scheme (either as symlinks or
       hardlinks), these will also be installed in the location pointed to by CONFIG_PREFIX.

USAGE

       BusyBox is a multi-call binary.  A multi-call binary is an executable program that
       performs the same job as more than one utility program.  That means there is just a single
       BusyBox binary, but that single binary acts like a large number of utilities.  This allows
       BusyBox to be smaller since all the built-in utility programs (we call them applets) can
       share code for many common operations.

       You can also invoke BusyBox by issuing a command as an argument on the command line.  For
       example, entering

               /bin/busybox ls

       will also cause BusyBox to behave as 'ls'.

       Of course, adding '/bin/busybox' into every command would be painful.  So most people will
       invoke BusyBox using links to the BusyBox binary.

       For example, entering

               ln -s /bin/busybox ls
               ./ls

       will cause BusyBox to behave as 'ls' (if the 'ls' command has been compiled into BusyBox).
       Generally speaking, you should never need to make all these links yourself, as the BusyBox
       build system will do this for you when you run the 'make install' command.

       If you invoke BusyBox with no arguments, it will provide you with a list of the applets
       that have been compiled into your BusyBox binary.

COMMON OPTIONS

       Most BusyBox applets support the --help argument to provide a terse runtime description of
       their behavior.  If the CONFIG_FEATURE_VERBOSE_USAGE option has been enabled, more
       detailed usage information will also be available.

COMMANDS

       Currently available applets include:

               [, [[, acpid, adjtimex, ar, arch, arp, arping, ascii, ash, awk,
               base64, basename, bc, blkdiscard, blockdev, brctl, bunzip2, busybox,
               bzcat, bzip2, cal, cat, chgrp, chmod, chown, chpasswd, chroot, chvt,
               clear, cmp, cp, cpio, crc32, crond, crontab, cttyhack, cut, date,
               dc, dd, deallocvt, depmod, devmem, df, diff, dirname, dmesg,
               dnsdomainname, dos2unix, dpkg, dpkg-deb, du, dumpkmap, dumpleases,
               echo, ed, egrep, env, expand, expr, factor, fallocate, false,
               fatattr, fdisk, fgrep, find, findfs, fold, free, freeramdisk,
               fsfreeze, fstrim, ftpget, ftpput, getopt, getty, grep, groups,
               gunzip, gzip, halt, head, hexdump, hostid, hostname, httpd, hwclock,
               i2cdetect, i2cdump, i2cget, i2cset, i2ctransfer, id, ifconfig,
               ifdown, ifup, init, insmod, ionice, ip, ipcalc, ipneigh, kill,
               killall, klogd, last, less, link, linux32, linux64, linuxrc, ln,
               loadfont, loadkmap, logger, login, logname, logread, losetup, ls,
               lsmod, lsscsi, lzcat, lzma, lzop, md5sum, mdev, microcom, mim,
               mkdir, mkdosfs, mke2fs, mkfifo, mknod, mkpasswd, mkswap, mktemp,
               modinfo, modprobe, more, mount, mt, mv, nameif, nbd-client, nc,
               netstat, nl, nologin, nproc, nsenter, nslookup, nuke, od, openvt,
               partprobe, passwd, paste, patch, pidof, ping, ping6, pivot_root,
               poweroff, printf, ps, pwd, rdate, readlink, realpath, reboot,
               renice, reset, resume, rev, rm, rmdir, rmmod, route, rpm, rpm2cpio,
               run-init, run-parts, sed, seq, setkeycodes, setpriv, setsid, sh,
               sha1sum, sha256sum, sha3sum, sha512sum, shred, shuf, sleep, sort,
               ssl_client, start-stop-daemon, stat, static-sh, strings, stty, su,
               sulogin, svc, svok, swapoff, swapon, switch_root, sync, sysctl,
               syslogd, tac, tail, tar, taskset, tc, tee, telnet, telnetd, test,
               tftp, time, timeout, top, touch, tr, traceroute, traceroute6, true,
               truncate, ts, tty, tunctl, ubirename, udhcpc, udhcpd, uevent,
               umount, uname, uncompress, unexpand, uniq, unix2dos, unlink, unlzma,
               unshare, unxz, unzip, uptime, usleep, uudecode, uuencode, vconfig,
               vi, w, watch, watchdog, wc, wget, which, who, whoami, xargs, xxd,
               xz, xzcat, yes, zcat

COMMAND DESCRIPTIONS

       acpid
           acpid [-df] [-c CONFDIR] [-l LOGFILE] [-a ACTIONFILE] [-M MAPFILE] [-e
           PROC_EVENT_FILE] [-p PIDFILE]

           Listen to ACPI events and spawn specific helpers on event arrival

                   -d      Log to stderr, not log file (implies -f)
                   -f      Run in foreground
                   -c DIR  Config directory [/etc/acpi]
                   -e FILE /proc event file [/proc/acpi/event]
                   -l FILE Log file [/var/log/acpid.log]
                   -p FILE Pid file [/var/run/acpid.pid]
                   -a FILE Action file [/etc/acpid.conf]
                   -M FILE Map file [/etc/acpi.map]

           Accept and ignore compatibility options -g -m -s -S -v

       adjtimex
           adjtimex [-q] [-o OFS] [-f FREQ] [-p TCONST] [-t TICK]

           Read or set kernel time variables. See adjtimex(2)

                   -q      Quiet
                   -o OFF  Time offset, microseconds
                   -f FREQ Frequency adjust, integer kernel units (65536 is 1ppm)
                   -t TICK Microseconds per tick, usually 10000
                           (positive -t or -f values make clock run faster)
                   -p TCONST

       ar  ar x|p|t [-ov] ARCHIVE [FILE]...

           Extract or list FILEs from an ar archive

                   x       Extract
                   p       Extract to stdout
                   t       List
                   -o      Restore mtime
                   -v      Verbose

       arch
           arch

           Print system architecture

       arp arp [-vn]     [-H HWTYPE] [-i IF] -a [HOSTNAME] [-v]          [-i IF] -d HOSTNAME
           [pub] [-v] [-H HWTYPE] [-i IF] -s HOSTNAME HWADDR [temp] [-v] [-H HWTYPE] [-i IF] -s
           HOSTNAME HWADDR [netmask MASK] pub [-v] [-H HWTYPE] [-i IF] -Ds HOSTNAME IFACE
           [netmask MASK] pub

           Manipulate ARP cache

                   -a              Display (all) hosts
                   -d              Delete ARP entry
                   -s              Set new entry
                   -v              Verbose
                   -n              Don't resolve names
                   -i IF           Network interface
                   -D              Read HWADDR from IFACE
                   -A,-p AF        Protocol family
                   -H HWTYPE       Hardware address type

       arping
           arping [-fqbDUA] [-c CNT] [-w TIMEOUT] [-I IFACE] [-s SRC_IP] DST_IP

           Send ARP requests/replies

                   -f              Quit on first ARP reply
                   -q              Quiet
                   -b              Keep broadcasting, don't go unicast
                   -D              Exit with 1 if DST_IP replies
                   -U              Unsolicited ARP mode, update your neighbors
                   -A              ARP answer mode, update your neighbors
                   -c N            Stop after sending N ARP requests
                   -w TIMEOUT      Seconds to wait for ARP reply
                   -I IFACE        Interface to use (default eth0)
                   -s SRC_IP       Sender IP address
                   DST_IP          Target IP address

       ash ash [-il] [-|+Cabefmnuvx] [-|+o OPT]... [-c 'SCRIPT' [ARG0 ARGS] | FILE ARGS | -s
           ARGS]

           Unix shell interpreter

       awk awk [OPTIONS] [AWK_PROGRAM] [FILE]...

                   -v VAR=VAL      Set variable
                   -F SEP          Use SEP as field separator
                   -f FILE         Read program from FILE
                   -e AWK_PROGRAM

       base64
           base64 [-d] [-w COL] [FILE]

           Base64 encode or decode FILE to standard output

                   -d      Decode data
                   -w COL  Wrap lines at COL (default 76, 0 disables)

       basename
           basename FILE [SUFFIX] | -a FILE... | -s SUFFIX FILE...

           Strip directory path and SUFFIX from FILE

                   -a              All arguments are FILEs
                   -s SUFFIX       Remove SUFFIX (implies -a)

       bc  bc [-sqlw] [FILE]...

           Arbitrary precision calculator

                   -q      Quiet
                   -l      Load standard library
                   -s      Be POSIX compatible
                   -w      Warn if extensions are used

           $BC_LINE_LENGTH changes output width

       blkdiscard
           blkdiscard [-o OFS] [-l LEN] [-s] DEVICE

           Discard sectors on DEVICE

                   -o OFS  Byte offset into device
                   -l LEN  Number of bytes to discard
                   -s      Perform a secure discard

       blockdev
           blockdev OPTION BLOCKDEV

                   --setro         Set ro
                   --setrw         Set rw
                   --getro         Get ro
                   --getss         Get sector size
                   --getbsz        Get block size
                   --setbsz BYTES  Set block size
                   --getsz         Get device size in 512-byte sectors
                   --getsize64     Get device size in bytes
                   --getra         Get readahead in 512-byte sectors
                   --setra SECTORS Set readahead
                   --flushbufs     Flush buffers
                   --rereadpt      Reread partition table

       brctl
           brctl COMMAND [BRIDGE [ARGS]]

           Manage ethernet bridges Commands:

                   addbr BRIDGE            Create BRIDGE
                   delbr BRIDGE            Delete BRIDGE
                   addif BRIDGE IFACE      Add IFACE to BRIDGE
                   delif BRIDGE IFACE      Delete IFACE from BRIDGE

       bunzip2
           bunzip2 [-cfk] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       bzcat
           bzcat [FILE]...

           Decompress to stdout

       bzip2
           bzip2 [-cfkdt123456789] [FILE]...

           Compress FILEs (or stdin) with bzip2 algorithm

                   -1..9   Compression level
                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       cal cal [-jmy] [[MONTH] YEAR]

           Display a calendar

                   -j      Use julian dates
                   -m      Week starts on Monday
                   -y      Display the entire year

       cat cat [-nbvteA] [FILE]...

           Print FILEs to stdout

                   -n      Number output lines
                   -b      Number nonempty lines
                   -v      Show nonprinting characters as ^x or M-x
                   -t      ...and tabs as ^I
                   -e      ...and end lines with $
                   -A      Same as -vte

       chgrp
           chgrp [-RhLHPcvf]... GROUP FILE...

           Change the group membership of FILEs to GROUP

                   -h      Affect symlinks instead of symlink targets
                   -L      Traverse all symlinks to directories
                   -H      Traverse symlinks on command line only
                   -P      Don't traverse symlinks (default)
                   -R      Recurse
                   -c      List changed files
                   -v      Verbose
                   -f      Hide errors

       chmod
           chmod [-Rcvf] MODE[,MODE]... FILE...

           MODE is octal number (bit pattern sstrwxrwxrwx) or [ugoa]{+|-|=}[rwxXst]

                   -R      Recurse
                   -c      List changed files
                   -v      Verbose
                   -f      Hide errors

       chown
           chown [-RhLHPcvf]... USER[:[GRP]] FILE...

           Change the owner and/or group of FILEs to USER and/or GRP

                   -h      Affect symlinks instead of symlink targets
                   -L      Traverse all symlinks to directories
                   -H      Traverse symlinks on command line only
                   -P      Don't traverse symlinks (default)
                   -R      Recurse
                   -c      List changed files
                   -v      Verbose
                   -f      Hide errors

       chpasswd
           chpasswd [-me] [-c ALG] [-R DIR]

           Read user:password from stdin and update /etc/passwd

                   -e      Supplied passwords are in encrypted form
                   -m      Encrypt using md5, not des
                   -c ALG  des,md5,sha256/512 (default sha256)
                   -R DIR  Directory to chroot into

       chroot
           chroot NEWROOT [PROG ARGS]

           Run PROG with root directory set to NEWROOT

       chvt
           chvt N

           Change the foreground virtual terminal to /dev/ttyN

       clear
           clear

           Clear screen

       cmp cmp [-ls] [-n NUM] FILE1 [FILE2 [SKIP1 [SKIP2]]]

           Compare FILE1 with FILE2 (or stdin)

                   -l      Write the byte numbers (decimal) and values (octal)
                           for all differing bytes
                   -s      Quiet
                   -n NUM  Compare at most NUM bytes

       cp  cp [-arPLHpfinlsTu] SOURCE DEST or: cp [-arPLHpfinlsu] SOURCE... { -t DIRECTORY |
           DIRECTORY }

           Copy SOURCEs to DEST

                   -a      Same as -dpR
                   -R,-r   Recurse
                   -d,-P   Preserve symlinks (default if -R)
                   -L      Follow all symlinks
                   -H      Follow symlinks on command line
                   -p      Preserve file attributes if possible
                   -f      Overwrite
                   -i      Prompt before overwrite
                   -n      Don't overwrite
                   -l,-s   Create (sym)links
                   -T      Refuse to copy if DEST is a directory
                   -t DIR  Copy all SOURCEs into DIR
                   -u      Copy only newer files

       cpio
           cpio [-dmvu] [-F FILE] [-R USER[:GRP]] [-H newc] [-tio] [EXTR_FILE]...

           Extract (-i) or list (-t) files from a cpio archive, or take file list from stdin and
           create an archive (-o)

           Main operation mode:

                   -t      List
                   -i      Extract EXTR_FILEs (or all)
                   -o      Create (requires -H newc)
           Options:

                   -H newc Archive format
                   -d      Make leading directories
                   -m      Restore mtime
                   -v      Verbose
                   -u      Overwrite
                   -F FILE Input (-t,-i,-p) or output (-o) file
                   -R USER[:GRP]   Set owner of created files
                   -L      Dereference symlinks
                   -0      NUL terminated input
                   --ignore-devno
                   --renumber-inodes

       crc32
           crc32 FILE...

           Calculate CRC32 checksum of FILEs

       crond
           crond [-fbS] [-l N] [-L LOGFILE] [-c DIR]

                   -f      Foreground
                   -b      Background (default)
                   -S      Log to syslog (default)
                   -l N    Set log level. Most verbose 0, default 8
                   -L FILE Log to FILE
                   -c DIR  Cron dir. Default:/var/spool/cron/crontabs

       crontab
           crontab [-c DIR] [-u USER] [-ler]|[FILE]

                   -c      Crontab directory
                   -u      User
                   -l      List crontab
                   -e      Edit crontab
                   -r      Delete crontab
                   FILE    Replace crontab by FILE ('-': stdin)

       cttyhack
           cttyhack [PROG ARGS]

           Give PROG a controlling tty if possible.  Example for /etc/inittab (for busybox init):
                ::respawn:/bin/cttyhack /bin/sh Giving controlling tty to shell running with PID
           1:      $ exec cttyhack sh Starting interactive shell from boot shell script:

                   setsid cttyhack sh

       cut cut [OPTIONS] [FILE]...

           Print selected fields from FILEs to stdout

                   -b LIST Output only bytes from LIST
                   -c LIST Output only characters from LIST
                   -d SEP  Field delimiter for input (default -f TAB, -F run of whitespace)
                   -O SEP  Field delimiter for output (default = -d for -f, one space for -F)
                   -D      Don't sort/collate sections or match -fF lines without delimiter
                   -f LIST Print only these fields (-d is single char)
                   -F LIST Print only these fields (-d is regex)
                   -s      Output only lines containing delimiter
                   -n      Ignored

       date
           date [OPTIONS] [+FMT] [[-s] TIME]

           Display time (using +FMT), or set time

                   -u              Work in UTC (don't convert to local time)
                   [-s] TIME       Set time to TIME
                   -d TIME         Display TIME, not 'now'
                   -D FMT          FMT (strptime format) for -s/-d TIME conversion
                   -r FILE         Display last modification time of FILE
                   -R              Output RFC-2822 date
                   -I[SPEC]        Output ISO-8601 date
                                   SPEC=date (default), hours, minutes, seconds or ns

           Recognized TIME formats:

                   @seconds_since_1970
                   hh:mm[:ss]
                   [YYYY.]MM.DD-hh:mm[:ss]
                   YYYY-MM-DD hh:mm[:ss]
                   [[[[[YY]YY]MM]DD]hh]mm[.ss]
                   'date TIME' form accepts MMDDhhmm[[YY]YY][.ss] instead

       dc  dc [-x] [-eSCRIPT]... [-fFILE]... [FILE]...

           Tiny RPN calculator. Operations: Arithmetic: + - * / % ^ ~ - divide with remainder | -
           modular exponentiation v - square root p - print top of the stack without popping f -
           print entire stack k - pop the value and set precision i - pop the value and set input
           radix o - pop the value and set output radix Examples: dc -e'2 2 + p' -> 4, dc -e'8 8
           * 2 2 + / p' -> 16

       dd  dd [if=FILE] [of=FILE] [ibs=N obs=N/bs=N] [count=N] [skip=N] [seek=N]
                [conv=notrunc|noerror|sync|fsync]
                [iflag=skip_bytes|count_bytes|fullblock|direct] [oflag=seek_bytes|append|direct]

           Copy a file with converting and formatting

                   if=FILE         Read from FILE instead of stdin
                   of=FILE         Write to FILE instead of stdout
                   bs=N            Read and write N bytes at a time
                   ibs=N           Read N bytes at a time
                   obs=N           Write N bytes at a time
                   count=N         Copy only N input blocks
                   skip=N          Skip N input blocks
                   seek=N          Skip N output blocks
                   conv=notrunc    Don't truncate output file
                   conv=noerror    Continue after read errors
                   conv=sync       Pad blocks with zeros
                   conv=fsync      Physically write data out before finishing
                   conv=swab       Swap every pair of bytes
                   iflag=skip_bytes        skip=N is in bytes
                   iflag=count_bytes       count=N is in bytes
                   oflag=seek_bytes        seek=N is in bytes
                   iflag=direct    O_DIRECT input
                   oflag=direct    O_DIRECT output
                   iflag=fullblock Read full blocks
                   oflag=append    Open output in append mode
                   status=noxfer   Suppress rate output
                   status=none     Suppress all output

           N may be suffixed by c (1), w (2), b (512), kB (1000), k (1024), MB, M, GB, G

       deallocvt
           deallocvt [N]

           Deallocate unused virtual terminal /dev/ttyN

       depmod
           depmod [-n] [-b BASE] [VERSION] [MODFILES]...

           Generate modules.dep, alias, and symbols files

                   -b BASE Use BASE/lib/modules/VERSION
                   -n      Dry run: print files to stdout

       devmem
           devmem ADDRESS [WIDTH [VALUE]]

           Read/write from physical address

                   ADDRESS Address to act upon
                   WIDTH   Width (8/16/...)
                   VALUE   Data to be written

       df  df [-PkmhTai] [-B SIZE] [-t TYPE] [FILESYSTEM]...

           Print filesystem usage statistics

                   -P      POSIX output format
                   -k      1024-byte blocks (default)
                   -m      1M-byte blocks
                   -h      Human readable (e.g. 1K 243M 2G)
                   -T      Print filesystem type
                   -t TYPE Print only mounts of this type
                   -a      Show all filesystems
                   -i      Inodes
                   -B SIZE Blocksize

       diff
           diff [-abBdiNqrTstw] [-L LABEL] [-S FILE] [-U LINES] FILE1 FILE2

           Compare files line by line and output the differences between them.  This
           implementation supports unified diffs only.

                   -a      Treat all files as text
                   -b      Ignore changes in the amount of whitespace
                   -B      Ignore changes whose lines are all blank
                   -d      Try hard to find a smaller set of changes
                   -i      Ignore case differences
                   -L      Use LABEL instead of the filename in the unified header
                   -N      Treat absent files as empty
                   -q      Output only whether files differ
                   -r      Recurse
                   -S      Start with FILE when comparing directories
                   -T      Make tabs line up by prefixing a tab when necessary
                   -s      Report when two files are the same
                   -t      Expand tabs to spaces in output
                   -U      Output LINES lines of context
                   -w      Ignore all whitespace

       dirname
           dirname FILENAME

           Strip non-directory suffix from FILENAME

       dmesg
           dmesg [-cr] [-n LEVEL] [-s SIZE]

           Print or control the kernel ring buffer

                   -c              Clear ring buffer after printing
                   -n LEVEL        Set console logging level
                   -s SIZE         Buffer size
                   -r              Print raw message buffer

       dos2unix
           dos2unix [-ud] [FILE]

           Convert FILE in-place from DOS to Unix format.  When no file is given, use
           stdin/stdout.

                   -u      dos2unix
                   -d      unix2dos

       dpkg
           dpkg [-ilCPru] [-F OPT] PACKAGE

           Install, remove and manage Debian packages

                   -i,--install    Install the package
                   -l,--list       List of installed packages
                   --configure     Configure an unpackaged package
                   -P,--purge      Purge all files of a package
                   -r,--remove     Remove all but the configuration files for a package
                   --unpack        Unpack a package, but don't configure it
                   --force-depends Ignore dependency problems
                   --force-confnew Overwrite existing config files when installing
                   --force-confold Keep old config files when installing

       dpkg-deb
           dpkg-deb [-cefxX] FILE [DIR]

           Perform actions on Debian packages (.deb)

                   -c      List files
                   -f      Print control fields
                   -e      Extract control files to DIR (default: ./DEBIAN)
                   -x      Extract files to DIR (no default)
                   -X      Verbose extract

       du  du [-aHLdclsxhmk] [FILE]...

           Summarize disk space used for FILEs (or directories)

                   -a      Show file sizes too
                   -b      Apparent size (including holes)
                   -L      Follow all symlinks
                   -H      Follow symlinks on command line
                   -d N    Limit output to directories (and files with -a) of depth < N
                   -c      Show grand total
                   -l      Count sizes many times if hard linked
                   -s      Display only a total for each argument
                   -x      Skip directories on different filesystems
                   -h      Sizes in human readable format (e.g., 1K 243M 2G)
                   -m      Sizes in megabytes
                   -k      Sizes in kilobytes (default)

       dumpkmap
           dumpkmap > keymap

           Print a binary keyboard translation table to stdout

       dumpleases
           dumpleases [-r|-a] [-d] [-f LEASEFILE]

           Display DHCP leases granted by udhcpd

                   -f FILE Lease file
                   -r      Show remaining time
                   -a      Show expiration time
                   -d      Show time in seconds

       echo
           echo [-neE] [ARG]...

           Print ARGs to stdout

                   -n      No trailing newline
                   -e      Interpret backslash escapes (\t=tab etc)
                   -E      Don't interpret backslash escapes (default)

       ed  ed [-p PROMPT] [-s] [FILE]

       env env [-i0] [-u NAME]... [-] [NAME=VALUE]... [PROG ARGS]

           Print current environment or run PROG after setting up environment

                   -, -i   Start with empty environment
                   -0      NUL terminated output
                   -u NAME Remove variable from environment

       expand
           expand [-i] [-t N] [FILE]...

           Convert tabs to spaces, writing to stdout

                   -i      Don't convert tabs after non blanks
                   -t      Tabstops every N chars

       expr
           expr EXPRESSION

           Print the value of EXPRESSION

           EXPRESSION may be:

                   ARG1 | ARG2     ARG1 if it is neither null nor 0, otherwise ARG2
                   ARG1 & ARG2     ARG1 if neither argument is null or 0, otherwise 0
                   ARG1 < ARG2     1 if ARG1 is less than ARG2, else 0. Similarly:
                   ARG1 <= ARG2
                   ARG1 = ARG2
                   ARG1 != ARG2
                   ARG1 >= ARG2
                   ARG1 > ARG2
                   ARG1 + ARG2     Sum of ARG1 and ARG2. Similarly:
                   ARG1 - ARG2
                   ARG1 * ARG2
                   ARG1 / ARG2
                   ARG1 % ARG2
                   STRING : REGEXP         Anchored pattern match of REGEXP in STRING
                   match STRING REGEXP     Same as STRING : REGEXP
                   substr STRING POS LEN   Substring of STRING, POS counts from 1
                   index STRING CHARS      Index in STRING where any CHARS is found, or 0
                   length STRING           Length of STRING
                   quote TOKEN             Interpret TOKEN as a string, even if
                                           it is a keyword like 'match' or an
                                           operator like '/'
                   (EXPRESSION)            Value of EXPRESSION

           Beware that many operators need to be escaped or quoted for shells.  Comparisons are
           arithmetic if both ARGs are numbers, else lexicographical. Pattern matches return the
           string matched between \( and \) or null; if \( and \) are not used, they return the
           number of characters matched or 0.

       factor
           factor [NUMBER]...

           Print prime factors

       fallocate
           fallocate [-o OFS] -l LEN FILE

           Preallocate space for FILE

                   -o OFS  Offset of range
                   -l LEN  Length of range

       fatattr
           fatattr [-+rhsvda] FILE...

           Change file attributes on FAT filesystem

                   -       Clear attributes
                   +       Set attributes
                   r       Read only
                   h       Hidden
                   s       System
                   v       Volume label
                   d       Directory
                   a       Archive

       fdisk
           fdisk [-ul] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK

           Change partition table

                   -u              Start and End are in sectors (instead of cylinders)
                   -l              Show partition table for each DISK, then exit
                   -b 2048         (for certain MO disks) use 2048-byte sectors
                   -C CYLINDERS    Set number of cylinders/heads/sectors
                   -H HEADS        Typically 255
                   -S SECTORS      Typically 63

       find
           find [-HL] [PATH]... [OPTIONS] [ACTIONS]

           Search for files and perform actions on them.  First failed action stops processing of
           current file.  Defaults: PATH is current directory, action is '-print'

                   -L,-follow      Follow symlinks
                   -H              ...on command line only
                   -xdev           Don't descend directories on other filesystems
                   -maxdepth N     Descend at most N levels. -maxdepth 0 applies
                                   actions to command line arguments only
                   -mindepth N     Don't act on first N levels
                   -depth          Act on directory *after* traversing it

           Actions:

                   ( ACTIONS )     Group actions for -o / -a
                   ! ACT           Invert ACT's success/failure
                   ACT1 [-a] ACT2  If ACT1 fails, stop, else do ACT2
                   ACT1 -o ACT2    If ACT1 succeeds, stop, else do ACT2
                                   Note: -a has higher priority than -o
                   -name PATTERN   Match file name (w/o directory name) to PATTERN
                   -iname PATTERN  Case insensitive -name
                   -path PATTERN   Match path to PATTERN
                   -ipath PATTERN  Case insensitive -path
                   -regex PATTERN  Match path to regex PATTERN
                   -type X         File type is X (one of: f,d,l,b,c,s,p)
                   -executable     File is executable
                   -perm MASK      At least one mask bit (+MASK), all bits (-MASK),
                                   or exactly MASK bits are set in file's mode
                   -mtime DAYS     mtime is greater than (+N), less than (-N),
                                   or exactly N days in the past
                   -atime DAYS     atime +N/-N/N days in the past
                   -ctime DAYS     ctime +N/-N/N days in the past
                   -mmin MINS      mtime is greater than (+N), less than (-N),
                                   or exactly N minutes in the past
                   -amin MINS      atime +N/-N/N minutes in the past
                   -cmin MINS      ctime +N/-N/N minutes in the past
                   -newer FILE     mtime is more recent than FILE's
                   -inum N         File has inode number N
                   -samefile FILE  File is same as FILE
                   -user NAME/ID   File is owned by given user
                   -group NAME/ID  File is owned by given group
                   -size N[bck]    File size is N (c:bytes,k:kbytes,b:512 bytes(def.))
                                   +/-N: file size is bigger/smaller than N
                   -links N        Number of links is greater than (+N), less than (-N),
                                   or exactly N
                   -empty          Match empty file/directory
                   -prune          If current file is directory, don't descend into it
           If none of the following actions is specified, -print is assumed
                   -print          Print file name
                   -print0         Print file name, NUL terminated
                   -exec CMD ARG ; Run CMD with all instances of {} replaced by
                                   file name. Fails if CMD exits with nonzero
                   -exec CMD ARG + Run CMD with {} replaced by list of file names
                   -quit           Exit

       findfs
           findfs LABEL=label or UUID=uuid

           Find a filesystem device based on a label or UUID

       fold
           fold [-bs] [-w WIDTH] [FILE]...

           Wrap input lines in FILEs (or stdin), writing to stdout

                   -b      Count bytes rather than columns
                   -s      Break at spaces
                   -w      Use WIDTH columns instead of 80

       free
           free [-bkmgh]

           Display free and used memory

       freeramdisk
           freeramdisk DEVICE

           Free all memory used by the specified ramdisk

       fsfreeze
           fsfreeze --[un]freeze MOUNTPOINT

           Flush and halt writes to MOUNTPOINT

       fstrim
           fstrim [OPTIONS] MOUNTPOINT

                   -o OFFSET       Offset in bytes to discard from
                   -l LEN          Bytes to discard
                   -m MIN          Minimum extent length
                   -v              Print number of discarded bytes

       ftpget
           ftpget [OPTIONS] HOST [LOCAL_FILE] REMOTE_FILE

           Download a file via FTP

                   -c      Continue previous transfer
                   -v      Verbose
                   -u USER Username
                   -p PASS Password
                   -P PORT

       ftpput
           ftpput [OPTIONS] HOST [REMOTE_FILE] LOCAL_FILE

           Upload a file to a FTP server

                   -v      Verbose
                   -u USER Username
                   -p PASS Password
                   -P PORT

       getopt
           getopt [OPTIONS] [--] OPTSTRING PARAMS

                   -a              Allow long options starting with single -
                   -l LOPT[,...]   Long options to recognize
                   -n PROGNAME     The name under which errors are reported
                   -o OPTSTRING    Short options to recognize
                   -q              No error messages on unrecognized options
                   -Q              No normal output
                   -s SHELL        Set shell quoting conventions
                   -T              Version test (exits with 4)
                   -u              Don't quote output

           Example:

           O=`getopt -l bb: -- ab:c:: "$@"` || exit 1 eval set -- "$O" while true; do      case
           "$1" in      -a)  echo A; shift;;      -b|--bb) echo "B:'$2'"; shift 2;;
                -c)  case "$2" in           "")  echo C; shift 2;;           *)   echo "C:'$2'";
           shift 2;;           esac;;      --)  shift; break;;      *)   echo Error; exit 1;;
                esac done

       getty
           getty [OPTIONS] BAUD_RATE[,BAUD_RATE]... TTY [TERMTYPE]

           Open TTY, prompt for login name, then invoke /bin/login

                   -h              Enable hardware RTS/CTS flow control
                   -L              Set CLOCAL (ignore Carrier Detect state)
                   -m              Get baud rate from modem's CONNECT status message
                   -n              Don't prompt for login name
                   -w              Wait for CR or LF before sending /etc/issue
                   -i              Don't display /etc/issue
                   -f ISSUE_FILE   Display ISSUE_FILE instead of /etc/issue
                   -l LOGIN        Invoke LOGIN instead of /bin/login
                   -t SEC          Terminate after SEC if no login name is read
                   -I INITSTR      Send INITSTR before anything else
                   -H HOST         Log HOST into the utmp file as the hostname

           BAUD_RATE of 0 leaves it unchanged

       grep
           grep [-HhnlLoqvsrRiwFEz] [-m N] [-A|B|C N] { PATTERN | -e PATTERN... | -f FILE... }
           [FILE]...

           Search for PATTERN in FILEs (or stdin)

                   -H      Add 'filename:' prefix
                   -h      Do not add 'filename:' prefix
                   -n      Add 'line_no:' prefix
                   -l      Show only names of files that match
                   -L      Show only names of files that don't match
                   -c      Show only count of matching lines
                   -o      Show only the matching part of line
                   -q      Quiet. Return 0 if PATTERN is found, 1 otherwise
                   -v      Select non-matching lines
                   -s      Suppress open and read errors
                   -r      Recurse
                   -R      Recurse and dereference symlinks
                   -i      Ignore case
                   -w      Match whole words only
                   -x      Match whole lines only
                   -F      PATTERN is a literal (not regexp)
                   -E      PATTERN is an extended regexp
                   -z      NUL terminated input
                   -m N    Match up to N times per file
                   -A N    Print N lines of trailing context
                   -B N    Print N lines of leading context
                   -C N    Same as '-A N -B N'
                   -e PTRN Pattern to match
                   -f FILE Read pattern from file

       groups
           groups [USER]

           Print the groups USER is in

       gunzip
           gunzip [-cfkt] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       gzip
           gzip [-cfkdt] [FILE]...

           Compress FILEs (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       halt
           halt [-d DELAY] [-nfw]

           Halt the system

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)
                   -w      Only write a wtmp record

       head
           head [OPTIONS] [FILE]...

           Print first 10 lines of FILEs (or stdin).  With more than one FILE, precede each with
           a filename header.

                   -n N[bkm]       Print first N lines
                   -n -N[bkm]      Print all except N last lines
                   -c [-]N[bkm]    Print first N bytes
                                   (b:*512 k:*1024 m:*1024^2)
                   -q              Never print headers
                   -v              Always print headers

       hexdump
           hexdump [-bcdoxCv] [-e FMT] [-f FMT_FILE] [-n LEN] [-s OFS] [FILE]...

           Display FILEs (or stdin) in a user specified format

                   -b              1-byte octal display
                   -c              1-byte character display
                   -d              2-byte decimal display
                   -o              2-byte octal display
                   -x              2-byte hex display
                   -C              hex+ASCII 16 bytes per line
                   -v              Show all (no dup folding)
                   -e FORMAT_STR   Example: '16/1 "%02x|""\n"'
                   -f FORMAT_FILE
                   -n LENGTH       Show only first LENGTH bytes
                   -s OFFSET       Skip OFFSET bytes

       hostid
           hostid

           Print out a unique 32-bit identifier for the machine

       hostname
           hostname [-sidf] [HOSTNAME | -F FILE]

           Show or set hostname or DNS domain name

                   -s      Short
                   -i      Addresses for the hostname
                   -d      DNS domain name
                   -f      Fully qualified domain name
                   -F FILE Use FILE's content as hostname

       httpd
           httpd [-ifv[v]] [-c CONFFILE] [-p [IP:]PORT] [-u USER[:GRP]] [-r REALM] [-h HOME] or
           httpd -d/-e/-m STRING

           Listen for incoming HTTP requests

                   -i              Inetd mode
                   -f              Run in foreground
                   -v[v]           Verbose
                   -p [IP:]PORT    Bind to IP:PORT (default *:80)
                   -u USER[:GRP]   Set uid/gid after binding to port
                   -r REALM        Authentication Realm for Basic Authentication
                   -h HOME         Home directory (default .)
                   -c FILE         Configuration file (default {/etc,HOME}/httpd.conf)
                   -m STRING       MD5 crypt STRING
                   -e STRING       HTML encode STRING
                   -d STRING       URL decode STRING

       hwclock
           hwclock [-swul] [--systz] [-f DEV]

           Show or set hardware clock (RTC)

                   -s      Set system time from RTC
                   -w      Set RTC from system time
                   --systz Set in-kernel timezone, correct system time
                           if RTC is kept in local time
                   -f DEV  Use specified device (e.g. /dev/rtc2)
                   -u      Assume RTC is kept in UTC
                   -l      Assume RTC is kept in local time
                           (if neither is given, read from /etc/adjtime)

       i2cdetect
           i2cdetect -l | -F I2CBUS | [-ya] [-q|-r] I2CBUS [FIRST LAST]

           Detect I2C chips

                   -l      List installed buses
                   -F BUS# List functionalities on this bus
                   -y      Disable interactive mode
                   -a      Force scanning of non-regular addresses
                   -q      Use smbus quick write commands for probing (default)
                   -r      Use smbus read byte commands for probing
                   FIRST and LAST limit probing range

       i2cdump
           i2cdump [-fy] [-r FIRST-LAST] BUS ADDR [MODE]

           Examine I2C registers

                   I2CBUS  I2C bus number
                   ADDRESS 0x03-0x77
           MODE is:

                   b       Byte (default)
                   w       Word
                   W       Word on even register addresses
                   i       I2C block
                   s       SMBus block
                   c       Consecutive byte
                   Append p for SMBus PEC

                   -f      Force access
                   -y      Disable interactive mode
                   -r      Limit the number of registers being accessed

       i2cget
           i2cget [-fy] BUS CHIP-ADDRESS [DATA-ADDRESS [MODE]]

           Read from I2C/SMBus chip registers

                   I2CBUS  I2C bus number
                   ADDRESS 0x03-0x77
           MODE is:

                   b       Read byte data (default)
                   w       Read word data
                   c       Write byte/read byte
                   Append p for SMBus PEC

                   -f      Force access
                   -y      Disable interactive mode

       i2cset
           i2cset [-fy] [-m MASK] BUS CHIP-ADDRESS DATA-ADDRESS [VALUE] ... [MODE]

           Set I2C registers

                   I2CBUS  I2C bus number
                   ADDRESS 0x03-0x77
           MODE is:

                   c       Byte, no value
                   b       Byte data (default)
                   w       Word data
                   i       I2C block data
                   s       SMBus block data
                   Append p for SMBus PEC

                   -f      Force access
                   -y      Disable interactive mode
                   -r      Read back and compare the result
                   -m MASK Mask specifying which bits to write

       i2ctransfer
           i2ctransfer [-fay] I2CBUS { rLENGTH[@ADDR] | wLENGTH[@ADDR] DATA...}...

           Read/write I2C data in one transfer

                   -f      Force access to busy addresses
                   -a      Force access to non-regular addresses
                   -y      Disable interactive mode

       id  id [-ugGnr] [USER]

           Print information about USER or the current user

                   -u      User ID
                   -g      Group ID
                   -G      Supplementary group IDs
                   -n      Print names instead of numbers
                   -r      Print real ID instead of effective ID

       ifconfig
           ifconfig [-a] [IFACE] [ADDRESS]

           Configure a network interface

                   [add ADDRESS[/PREFIXLEN]]
                   [del ADDRESS[/PREFIXLEN]]
                   [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]]
                   [netmask ADDRESS] [dstaddr ADDRESS]
                   [outfill NN] [keepalive NN]
                   [hw ether|infiniband ADDRESS] [metric NN] [mtu NN]
                   [[-]trailers] [[-]arp] [[-]allmulti]
                   [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic]
                   [mem_start NN] [io_addr NN] [irq NN]
                   [up|down] ...

       ifdown
           ifdown [-nmvf] [-i FILE] -a | IFACE...

                   -a      Deconfigure all interfaces
                   -i FILE Use FILE instead of /etc/network/interfaces
                   -n      Dry run
                           (note: doesn't disable mappings)
                   -m      Don't run any mappings
                   -v      Print out what would happen before doing it
                   -f      Force

       ifup
           ifup [-nmvf] [-i FILE] -a | IFACE...

                   -a      Configure all interfaces
                   -i FILE Use FILE instead of /etc/network/interfaces
                   -n      Dry run
                           (note: doesn't disable mappings)
                   -m      Don't run any mappings
                   -v      Print out what would happen before doing it
                   -f      Force

       init
           init

           Init is the first process started during boot. It never exits.  It (re)spawns children
           according to /etc/inittab.  Signals:

           HUP: reload /etc/inittab TSTP: stop respawning until CONT QUIT: re-exec another init
           USR1/TERM/USR2/INT: run halt/reboot/poweroff/Ctrl-Alt-Del script

       insmod
           insmod FILE [SYMBOL=VALUE]...

           Load kernel module

       ionice
           ionice [-c 1-3] [-n 0-7] [-t] { -p PID | PROG ARGS }

           Change I/O priority and class

                   -c N    Class. 1:realtime 2:best-effort 3:idle
                   -n N    Priority
                   -t      Ignore errors

       ip  ip [OPTIONS] address|route|link|tunnel|neigh|rule [ARGS]

           OPTIONS := -f[amily] inet|inet6|link | -o[neline]

           ip addr add|del IFADDR dev IFACE | show|flush [dev IFACE] [to PREFIX] ip route
           list|flush|add|del|change|append|replace|test ROUTE ip link set IFACE [up|down] [arp
           on|off] [multicast on|off]      [promisc on|off] [mtu NUM] [name NAME] [qlen NUM]
           [address MAC]      [master IFACE | nomaster] [netns PID] ip tunnel add|change|del|show
           [NAME]      [mode ipip|gre|sit] [remote ADDR] [local ADDR] [ttl TTL] ip neigh
           show|flush [to PREFIX] [dev DEV] [nud STATE] ip rule [list] | add|del SELECTOR ACTION

       ipcalc
           ipcalc [-bnmphs] ADDRESS[/PREFIX] [NETMASK]

           Calculate and display network settings from IP address

                   -b      Broadcast address
                   -n      Network address
                   -m      Default netmask for IP
                   -p      Prefix for IP/NETMASK
                   -h      Resolved host name
                   -s      No error messages

       ipneigh
           ipneigh show|flush [to PREFIX] [dev DEV] [nud STATE]

       kill
           kill [-l] [-SIG] PID...

           Send a signal (default: TERM) to given PIDs

                   -l      List all signal names and numbers

       killall
           killall [-lq] [-SIG] PROCESS_NAME...

           Send a signal (default: TERM) to given processes

                   -l      List all signal names and numbers
                   -q      Don't complain if no processes were killed

       klogd
           klogd [-c N] [-n]

           Log kernel messages to syslog

                   -c N    Print to console messages more urgent than prio N (1-8)
                   -n      Run in foreground

       last
           last

           Show listing of the last users that logged into the system

       less
           less [-EFIMmNSRh~] [FILE]...

           View FILE (or stdin) one screenful at a time

                   -E      Quit once the end of a file is reached
                   -F      Quit if entire file fits on first screen
                   -I      Ignore case in all searches
                   -M,-m   Display status line with line numbers
                           and percentage through the file
                   -N      Prefix line number to each line
                   -S      Truncate long lines
                   -R      Remove color escape codes in input
                   -~      Suppress ~s displayed past EOF

       link
           link FILE LINK

           Create hard LINK to FILE

       ln  ln [-sfnbtv] [-S SUF] TARGET... LINK|DIR

           Create a link LINK or DIR/TARGET to the specified TARGET(s)

                   -s      Make symlinks instead of hardlinks
                   -f      Remove existing destinations
                   -n      Don't dereference symlinks - treat like normal file
                   -b      Make a backup of the target (if exists) before link operation
                   -S SUF  Use suffix instead of ~ when making backup files
                   -T      Treat LINK as a file, not DIR
                   -v      Verbose

       loadfont
           loadfont < font

           Load a console font from stdin

       loadkmap
           loadkmap < keymap

           Load a binary keyboard translation table from stdin

       logger
           logger [-s] [-t TAG] [-p PRIO] [MESSAGE]

           Write MESSAGE (or stdin) to syslog

                   -s      Log to stderr as well as the system log
                   -t TAG  Log using the specified tag (defaults to user name)
                   -p PRIO Priority (number or FACILITY.LEVEL pair)

       login
           login [-p] [-h HOST] [[-f] USER]

           Begin a new session on the system

                   -f      Don't authenticate (user already authenticated)
                   -h HOST Host user came from (for network logins)
                   -p      Preserve environment

           $LOGIN_TIMEOUT      Seconds (default 60, 0 - disable)

       logname
           logname

           Print the name of the current user

       logread
           logread [-fF]

           Show messages in syslogd's circular buffer

                   -f      Output data as log grows
                   -F      Same as -f, but dump buffer first

       losetup
           losetup [-rP] [-o OFS] {-f|LOOPDEV} FILE: associate loop devices      losetup -c
           LOOPDEV: reread file size      losetup -d LOOPDEV: disassociate      losetup -a: show
           status      losetup -f: show next free loop device

                   -o OFS  Start OFS bytes into FILE
                   -P      Scan for partitions
                   -r      Read-only
                   -f      Show/use next free loop device

       ls  ls [-1AaCxdLHRFplinshrSXvctu] [-w WIDTH] [FILE]...

           List directory contents

                   -1      One column output
                   -a      Include names starting with .
                   -A      Like -a, but exclude . and ..
                   -x      List by lines
                   -d      List directory names, not contents
                   -L      Follow symlinks
                   -H      Follow symlinks on command line
                   -R      Recurse
                   -p      Append / to directory names
                   -F      Append indicator (one of */=@|) to names
                   -l      Long format
                   -i      List inode numbers
                   -n      List numeric UIDs and GIDs instead of names
                   -s      List allocated blocks
                   -lc     List ctime
                   -lu     List atime
                   --full-time     List full date/time
                   -h      Human readable sizes (1K 243M 2G)
                   --group-directories-first
                   -S      Sort by size
                   -X      Sort by extension
                   -v      Sort by version
                   -t      Sort by mtime
                   -tc     Sort by ctime
                   -tu     Sort by atime
                   -r      Reverse sort order
                   -w N    Format N columns wide
                   --color[={always,never,auto}]

       lsmod
           lsmod

           List loaded kernel modules

       lzcat
           lzcat [FILE]...

           Decompress to stdout

       lzma
           lzma -d [-cfk] [FILE]...

           Decompress FILEs (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       lzop
           lzop [-cfUvd123456789CF] [FILE]...

                   -1..9   Compression level
                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -U      Delete input files
                   -v      Verbose
                   -F      Don't store or verify checksum
                   -C      Also write checksum of compressed block

       md5sum
           md5sum [-c[sw]] [FILE]...

           Print or check MD5 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

       mdev
           mdev [-vS] { [-s] | [-df] }

                   -v      Verbose
                   -S      Log to syslog too
                   -s      Scan /sys and populate /dev
                   -d      Daemon, listen on netlink
                   -f      Run in foreground

           Bare mdev is a kernel hotplug helper. To activate it:      echo /sbin/mdev
           >/proc/sys/kernel/hotplug

           It uses /etc/mdev.conf with lines      [-][ENV=regex;]...DEVNAME UID:GID PERM
           [>|=PATH]|[!] [@|$|*PROG] where DEVNAME is device name regex, @major,minor[-minor2],
           or environment variable regex. A common use of the latter is to load modules for
           hotplugged devices:

                   $MODALIAS=.* 0:0 660 @modprobe "$MODALIAS"

           If /dev/mdev.seq file exists, mdev will wait for its value to match $SEQNUM variable.
           This prevents plug/unplug races.  To activate this feature, create empty /dev/mdev.seq
           at boot.

           If /dev/mdev.log file exists, debug log will be appended to it.

       microcom
           microcom [-d DELAY_MS] [-t TIMEOUT_MS ] [-s SPEED] [-X] TTY

           Copy bytes from stdin to TTY and from TTY to stdout

                   -d DELAY        Wait up to DELAY ms for TTY output before sending
                                   every next byte to it
                   -t TIMEOUT      Exit if both stdin and TTY are silent for TIMEOUT ms
                   -s SPEED        Set serial line to SPEED
                   -X              Disable special meaning of NUL and Ctrl-X from stdin

       mim mim [-f FILE] [SHELL_OPTIONS] [TARGET] ...

           Run a script from a Makefile-like specification file

                   -f FILE         Spec file (default Mimfile)

       mkdir
           mkdir [-m MODE] [-p] DIRECTORY...

           Create DIRECTORY

                   -m MODE Mode
                   -p      No error if exists; make parent directories as needed

       mkdosfs
           mkdosfs [-v] [-n LABEL] BLOCKDEV [KBYTES]

           Make a FAT32 filesystem

                   -v      Verbose
                   -n LBL  Volume label

       mke2fs
           mke2fs [-Fn] [-b BLK_SIZE] [-i INODE_RATIO] [-I INODE_SIZE] [-m RESERVED_PERCENT] [-L
           LABEL] BLOCKDEV [KBYTES]

                   -b BLK_SIZE     Block size, bytes
                   -F              Force
                   -i RATIO        Max number of files is filesystem_size / RATIO
                   -I BYTES        Inode size (min 128)
                   -L LBL          Volume label
                   -m PERCENT      Percent of blocks to reserve for admin
                   -n              Dry run

       mkfifo
           mkfifo [-m MODE] NAME

           Create named pipe

                   -m MODE Mode (default a=rw)

       mknod
           mknod [-m MODE] NAME TYPE [MAJOR MINOR]

           Create a special file (block, character, or pipe)

                   -m MODE Creation mode (default a=rw)
           TYPE:
                   b       Block device
                   c or u  Character device
                   p       Named pipe (MAJOR MINOR must be omitted)

       mkpasswd
           mkpasswd [-P FD] [-m TYPE] [-S SALT] [PASSWORD] [SALT]

           Print crypt(3) hashed PASSWORD

                   -P N    Read password from fd N
                   -m TYPE des,md5,sha256/512 (default sha256)
                   -S SALT

       mkswap
           mkswap [-L LBL] BLOCKDEV [KBYTES]

           Prepare BLOCKDEV to be used as swap partition

                   -L LBL  Label

       mktemp
           mktemp [-dt] [-p DIR] [TEMPLATE]

           Create a temporary file with name based on TEMPLATE and print its name.  TEMPLATE must
           end with XXXXXX (e.g. [/dir/]nameXXXXXX).  Without TEMPLATE, -t tmp.XXXXXX is assumed.

                   -d      Make directory, not file
                   -q      Fail silently on errors
                   -t      Prepend base directory name to TEMPLATE
                   -p DIR  Use DIR as a base directory (implies -t)
                   -u      Do not create anything; print a name

           Base directory is: -p DIR, else $TMPDIR, else /tmp

       modinfo
           modinfo [-adlpn0] [-F keyword] MODULE

                   -a              Shortcut for '-F author'
                   -d              Shortcut for '-F description'
                   -l              Shortcut for '-F license'
                   -p              Shortcut for '-F parm'
                   -F keyword      Keyword to look for
                   -0              NUL terminated output

       modprobe
           modprobe [-alrqvsDb] MODULE [SYMBOL=VALUE]...

                   -a      Load multiple MODULEs
                   -l      List (MODULE is a pattern)
                   -r      Remove MODULE (stacks) or do autoclean
                   -q      Quiet
                   -v      Verbose
                   -s      Log to syslog
                   -D      Show dependencies
                   -b      Apply blacklist to module names too

       more
           more [FILE]...

           View FILE (or stdin) one screenful at a time

       mount
           mount [OPTIONS] [-o OPT] DEVICE NODE

           Mount a filesystem. Filesystem autodetection requires /proc.

                   -a              Mount all filesystems in fstab
                   -f              Dry run
                   -i              Don't run mount helper
                   -r              Read-only mount
                   -t FSTYPE[,...] Filesystem type(s)
                   -T FILE         Read FILE instead of /etc/fstab
                   -O OPT          Mount only filesystems with option OPT (-a only)
           -o OPT:
                   loop            Ignored (loop devices are autodetected)
                   [a]sync         Writes are [a]synchronous
                   [no]atime       Disable/enable updates to inode access times
                   [no]diratime    Disable/enable atime updates to directories
                   [no]relatime    Disable/enable atime updates relative to modification time
                   [no]dev         (Dis)allow use of special device files
                   [no]exec        (Dis)allow use of executable files
                   [no]suid        (Dis)allow set-user-id-root programs
                   [r]shared       Convert [recursively] to a shared subtree
                   [r]slave        Convert [recursively] to a slave subtree
                   [r]private      Convert [recursively] to a private subtree
                   [un]bindable    Make mount point [un]able to be bind mounted
                   [r]bind         Bind a file or directory [recursively] to another location
                   move            Relocate an existing mount point
                   remount         Remount a mounted filesystem, changing flags
                   ro              Same as -r

           There are filesystem-specific -o flags.

       mt  mt [-f DEVICE] OPCODE VALUE

           Control magnetic tape drive operation

           Opcodes:

           bsf bsfm bsr bss datacompression drvbuffer eof eom erase fsf fsfm fsr fss load lock
           mkpart nop offline ras1 ras2 ras3 reset retension rewind rewoffline seek setblk
           setdensity setpart tell unload unlock weof wset

       mv  mv [-finT] SOURCE DEST or: mv [-fin] SOURCE... { -t DIRECTORY | DIRECTORY }

           Rename SOURCE to DEST, or move SOURCEs to DIRECTORY

                   -f      Don't prompt before overwriting
                   -i      Interactive, prompt before overwrite
                   -n      Don't overwrite an existing file
                   -T      Refuse to move if DEST is a directory
                   -t DIR  Move all SOURCEs into DIR

       nameif
           nameif [-s] [-c FILE] [IFNAME HWADDR]...

           Rename network interface while it in the down state.  The device with address HWADDR
           is renamed to IFNAME.

                   -c FILE Configuration file (default: /etc/mactab)
                   -s      Log to syslog

       nbd-client
           nbd-client { [-b BLKSIZE] [-N NAME] [-t SEC] [-p] HOST [PORT] | -d } BLOCKDEV

           Connect to HOST and provide network block device on BLOCKDEV

       nc  nc [-iN] [-wN] [-l] [-p PORT] [-f FILE|IPADDR PORT] [-e PROG]

           Open a pipe to IP:PORT or FILE

                   -l      Listen mode, for inbound connects
                           (use -ll with -e for persistent server)
                   -p PORT Local port
                   -w SEC  Connect timeout
                   -i SEC  Delay interval for lines sent
                   -f FILE Use file (ala /dev/ttyS0) instead of network
                   -e PROG Run PROG after connect

       netstat
           netstat [-ral] [-tuwx] [-en]

           Display networking information

                   -r      Routing table
                   -a      All sockets
                   -l      Listening sockets
                           Else: connected sockets
                   -t      TCP sockets
                   -u      UDP sockets
                   -w      Raw sockets
                   -x      Unix sockets
                           Else: all socket types
                   -e      Other/more information
                   -n      Don't resolve names

       nl  nl [OPTIONS] [FILE]...

           Write FILEs to standard output with line numbers added

                   -b STYLE        Which lines to number - a: all, t: nonempty, n: none
                   -i N            Line number increment
                   -s STRING       Use STRING as line number separator
                   -v N            Start from N
                   -w N            Width of line numbers

       nologin
           nologin

           Politely refuse a login

       nproc
           nproc [--all] [--ignore=N]

           Print number of available CPUs

                   --all           Number of installed CPUs
                   --ignore=N      Exclude N CPUs

       nsenter
           nsenter [OPTIONS] [PROG ARGS]

                   -t PID          Target process to get namespaces from
                   -m[FILE]        Enter mount namespace
                   -u[FILE]        Enter UTS namespace (hostname etc)
                   -i[FILE]        Enter System V IPC namespace
                   -n[FILE]        Enter network namespace
                   -p[FILE]        Enter pid namespace
                   -U[FILE]        Enter user namespace
                   -S UID          Set uid in entered namespace
                   -G GID          Set gid in entered namespace
                   --preserve-credentials  Don't touch uids or gids
                   -r[DIR]         Set root directory
                   -w[DIR]         Set working directory
                   -F              Don't fork before exec'ing PROG

       nslookup
           nslookup [-type=QUERY_TYPE] [-debug] HOST [DNS_SERVER]

           Query DNS about HOST

           QUERY_TYPE: soa,ns,a,aaaa,cname,mx,txt,ptr,srv,any

       nuke
           nuke DIR...

           Remove DIRs

       od  od [-abcdfhilovxs] [-t TYPE] [-A RADIX] [-N SIZE] [-j SKIP] [-S MINSTR] [-w WIDTH]
           [FILE]...

           Print FILEs (or stdin) unambiguously, as octal bytes by default

       openvt
           openvt [-c N] [-sw] [PROG ARGS]

           Start PROG on a new virtual terminal

                   -c N    Use specified VT
                   -s      Switch to the VT
                   -w      Wait for PROG to exit

       partprobe
           partprobe DEVICE...

           Ask kernel to rescan partition table

       passwd
           passwd [-a ALG] [-dlu] [USER]

           Change USER's password (default: current user)

                   -a ALG  des,md5,sha256/512 (default sha256)
                   -d      Set password to ''
                   -l      Lock (disable) account
                   -u      Unlock (enable) account

       paste
           paste [-d LIST] [-s] [FILE]...

           Paste lines from each input file, separated with tab

                   -d LIST Use delimiters from LIST, not tab
                   -s      Serial: one file at a time

       patch
           patch [-RNE] [-p N] [-i DIFF] [ORIGFILE [PATCHFILE]]

                   -p N    Strip N leading components from file names
                   -i DIFF Read DIFF instead of stdin
                   -R      Reverse patch
                   -N      Ignore already applied patches
                   -E      Remove output files if they become empty
                   --dry-run       Don't actually change files

       pidof
           pidof [NAME]...

           List PIDs of all processes with names that match NAMEs

       ping
           ping [OPTIONS] HOST

           Send ICMP ECHO_REQUESTs to HOST

                   -4,-6           Force IP or IPv6 name resolution
                   -c CNT          Send only CNT pings
                   -s SIZE         Send SIZE data bytes in packets (default 56)
                   -i SECS         Interval
                   -A              Ping as soon as reply is received
                   -t TTL          Set TTL
                   -I IFACE/IP     Source interface or IP address
                   -W SEC          Seconds to wait for the first response (default 10)
                                   (after all -c CNT packets are sent)
                   -w SEC          Seconds until ping exits (default:infinite)
                                   (can exit earlier with -c CNT)
                   -q              Quiet, only display output at start/finish
                   -p HEXBYTE      Payload pattern

       ping6
           ping6 [OPTIONS] HOST

           Send ICMP ECHO_REQUESTs to HOST

                   -c CNT          Send only CNT pings
                   -s SIZE         Send SIZE data bytes in packets (default 56)
                   -i SECS         Interval
                   -A              Ping as soon as reply is received
                   -I IFACE/IP     Source interface or IP address
                   -W SEC          Seconds to wait for the first response (default 10)
                                   (after all -c CNT packets are sent)
                   -w SEC          Seconds until ping exits (default:infinite)
                                   (can exit earlier with -c CNT)
                   -q              Quiet, only display output at start/finish
                   -p HEXBYTE      Payload pattern

       pivot_root
           pivot_root NEW_ROOT PUT_OLD

           Move the current root file system to PUT_OLD and make NEW_ROOT the new root file
           system

       poweroff
           poweroff [-d DELAY] [-nf]

           Halt and shut off power

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)

       printf
           printf FORMAT [ARG]...

           Format and print ARG(s) according to FORMAT (a-la C printf)

       ps  ps [-o COL1,COL2=HEADER] [-T]

           Show list of processes

                   -o COL1,COL2=HEADER     Select columns for display
                   -T                      Show threads

       pwd pwd

           Print the full filename of the current working directory

       rdate
           rdate [-s/-p] HOST

           Set and print time from HOST using RFC 868

                   -s      Only set system time
                   -p      Only print time

       readlink
           readlink [-fnv] FILE

           Display the value of a symlink

                   -f      Canonicalize by following all symlinks
                   -n      Don't add newline
                   -v      Verbose

       realpath
           realpath FILE...

           Print absolute pathnames of FILEs

       reboot
           reboot [-d DELAY] [-nf]

           Reboot the system

                   -d SEC  Delay interval
                   -n      Do not sync
                   -f      Force (don't go through init)

       renice
           renice [-n] PRIORITY [[-p|g|u] ID...]...

           Change scheduling priority of a running process

                   -n      Add PRIORITY to current nice value
                           Without -n, nice value is set to PRIORITY
                   -p      Process ids (default)
                   -g      Process group ids
                   -u      Process user names

       reset
           reset

           Reset terminal (ESC codes) and termios (signals, buffering, echo)

       resume
           resume BLOCKDEV [OFFSET]

           Restore system state from 'suspend-to-disk' data in BLOCKDEV

       rev rev [FILE]...

           Reverse lines of FILE

       rm  rm [-irf] FILE...

           Remove (unlink) FILEs

                   -i      Always prompt before removing
                   -f      Never prompt
                   -R,-r   Recurse

       rmdir
           rmdir [-p] DIRECTORY...

           Remove DIRECTORY if it is empty

                   -p      Include parents
                   --ignore-fail-on-non-empty

       rmmod
           rmmod [-wfa] [MODULE]...

           Unload kernel modules

                   -w      Wait until the module is no longer used
                   -f      Force unload
                   -a      Remove all unused modules (recursively)

       route
           route [-ne] [-A inet[6]] [{add|del} [-net|-host] TARGET [netmask MASK]      [gw
           GATEWAY] [metric N] [mss BYTES] [window BYTES] [reject] [IFACE]]

           Show or edit kernel routing tables

                   -n      Don't resolve names
                   -e      Display other/more information
                   -A inet[6]      Select address family

       rpm rpm -i PACKAGE.rpm; rpm -qp[ildc] PACKAGE.rpm

           Manipulate RPM packages

           Commands:

                   -i      Install package
                   -qp     Query package
                   -qpi    Show information
                   -qpl    List contents
                   -qpd    List documents
                   -qpc    List config files

       rpm2cpio
           rpm2cpio PACKAGE.rpm

           Output a cpio archive of the rpm file

       run-init
           run-init [-d CAP,CAP...] [-n] [-c CONSOLE_DEV] NEW_ROOT NEW_INIT [ARGS]

           Free initramfs and switch to another root fs:

           chroot to NEW_ROOT, delete all in /, move NEW_ROOT to /, execute NEW_INIT. PID must be
           1. NEW_ROOT must be a mountpoint.

                   -c DEV  Reopen stdio to DEV after switch
                   -d CAPS Drop capabilities
                   -n      Dry run

       run-parts
           run-parts [-a ARG]... [-u UMASK] [--reverse] [--test] [--exit-on-error] DIRECTORY

           Run a bunch of scripts in DIRECTORY

                   -a ARG          Pass ARG as argument to scripts
                   -u UMASK        Set UMASK before running scripts
                   --reverse       Reverse execution order
                   --test          Dry run
                   --exit-on-error Exit if a script exits with non-zero

       sed sed [-i[SFX]] [-nrE] [-f FILE]... [-e CMD]... [FILE]...  or: sed [-i[SFX]] [-nrE] CMD
           [FILE]...

                   -e CMD  Add CMD to sed commands to be executed
                   -f FILE Add FILE contents to sed commands to be executed
                   -i[SFX] Edit files in-place (otherwise write to stdout)
                           Optionally back files up, appending SFX
                   -n      Suppress automatic printing of pattern space
                   -r,-E   Use extended regex syntax

           If no -e or -f, the first non-option argument is the sed command string.  Remaining
           arguments are input files (stdin if none).

       seq seq [-w] [-s SEP] [FIRST [INC]] LAST

           Print numbers from FIRST to LAST, in steps of INC.  FIRST, INC default to 1.

                   -w      Pad to last with leading zeros
                   -s SEP  String separator

       setkeycodes
           setkeycodes { SCANCODE KEYCODE }...

           Modify kernel's scancode-to-keycode map, allowing unusual keyboards to generate usable
           keycodes.

           SCANCODE is either xx or e0xx (hexadecimal), KEYCODE is decimal.

       setpriv
           setpriv [OPTIONS] PROG ARGS

           Run PROG with different privilege settings

           -d,--dump      Show current capabilities --nnp,--no-new-privs     Ignore setuid/setgid
           bits and file capabilities --inh-caps CAP,CAP  Set inheritable capabilities
           --ambient-caps CAP,CAP    Set ambient capabilities

       setsid
           setsid [-c] PROG ARGS

           Run PROG in a new session. PROG will have no controlling terminal and will not be
           affected by keyboard signals (^C etc).

                   -c      Set controlling terminal to stdin

       sh  sh [-il] [-|+Cabefmnuvx] [-|+o OPT]... [-c 'SCRIPT' [ARG0 ARGS] | FILE ARGS | -s ARGS]

           Unix shell interpreter

       sha1sum
           sha1sum [-c[sw]] [FILE]...

           Print or check SHA1 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

       sha256sum
           sha256sum [-c[sw]] [FILE]...

           Print or check SHA256 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

       sha3sum
           sha3sum [-c[sw]] [-a BITS] [FILE]...

           Print or check SHA3 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines
                   -a BITS 224 (default), 256, 384, 512

       sha512sum
           sha512sum [-c[sw]] [FILE]...

           Print or check SHA512 checksums

                   -c      Check sums against list in FILEs
                   -s      Don't output anything, status code shows success
                   -w      Warn about improperly formatted checksum lines

       shred
           shred [-fuz] [-n N] [-s SIZE] FILE...

           Overwrite/delete FILEs

                   -f      Chmod to ensure writability
                   -s SIZE Size to write
                   -n N    Overwrite N times (default 3)
                   -z      Final overwrite with zeros
                   -u      Remove file

       shuf
           shuf [-n NUM] [-o FILE] [-z] [FILE | -e [ARG...] | -i L-H]

           Randomly permute lines

                   -n NUM  Output at most NUM lines
                   -o FILE Write to FILE, not standard output
                   -z      NUL terminated output
                   -e      Treat ARGs as lines
                   -i L-H  Treat numbers L-H as lines

       sleep
           sleep [N]...

           Pause for a time equal to the total of the args given, where each arg can have an
           optional suffix of (s)econds, (m)inutes, (h)ours, or (d)ays

       sort
           sort [-nrughMcszbdfiokt] [-o FILE] [-k START[.OFS][OPTS][,END[.OFS][OPTS]] [-t CHAR]
           [FILE]...

           Sort lines of text

                   -o FILE Output to FILE
                   -c      Check whether input is sorted
                   -b      Ignore leading blanks
                   -f      Ignore case
                   -i      Ignore unprintable characters
                   -d      Dictionary order (blank or alphanumeric only)
                   -n      Sort numbers
                   -g      General numerical sort
                   -h      Sort human readable numbers (2K 1G)
                   -M      Sort month
                   -V      Sort version
                   -t CHAR Field separator
                   -k N[,M] Sort by Nth field
                   -r      Reverse sort order
                   -s      Stable (don't sort ties alphabetically)
                   -u      Suppress duplicate lines
                   -z      NUL terminated input and output

       ssl_client
           ssl_client [-e] -s FD [-r FD] [-n SNI]

       start-stop-daemon
           start-stop-daemon [OPTIONS] [-S|-K] ... [-- ARGS...]

           Search for matching processes, and then -K: stop all matching processes -S: start a
           process unless a matching process is found

           Process matching:

                   -u USERNAME|UID Match only this user's processes
                   -n NAME         Match processes with NAME
                                   in comm field in /proc/PID/stat
                   -x EXECUTABLE   Match processes with this command
                                   in /proc/PID/cmdline
                   -p FILE         Match a process with PID from FILE
                   All specified conditions must match
           -S only:
                   -x EXECUTABLE   Program to run
                   -a NAME         Zeroth argument
                   -b              Background
                   -N N            Change nice level
                   -c USER[:[GRP]] Change user/group
                   -m              Write PID to pidfile specified by -p
           -K only:
                   -s SIG          Signal to send
                   -t              Match only, exit with 0 if found
           Other:

                   -o              Exit with status 0 if nothing is done
                   -v              Verbose
                   -q              Quiet

       stat
           stat [-ltf] [-c FMT] FILE...

           Display file (default) or filesystem status

                   -c FMT  Use the specified format
                   -f      Display filesystem status
                   -L      Follow links
                   -t      Terse display

           FMT sequences for files:

            %a     Access rights in octal
            %A     Access rights in human readable form
            %b     Number of blocks allocated (see %B)
            %B     Size in bytes of each block reported by %b
            %d     Device number in decimal
            %D     Device number in hex
            %f     Raw mode in hex
            %F     File type
            %g     Group ID
            %G     Group name
            %h     Number of hard links
            %i     Inode number
            %n     File name
            %N     File name, with -> TARGET if symlink
            %o     I/O block size
            %s     Total size in bytes
            %t     Major device type in hex
            %T     Minor device type in hex
            %u     User ID
            %U     User name
            %x     Time of last access
            %X     Time of last access as seconds since Epoch
            %y     Time of last modification
            %Y     Time of last modification as seconds since Epoch
            %z     Time of last change
            %Z     Time of last change as seconds since Epoch

           FMT sequences for file systems:

            %a     Free blocks available to non-superuser
            %b     Total data blocks
            %c     Total file nodes
            %d     Free file nodes
            %f     Free blocks
            %i     File System ID in hex
            %l     Maximum length of filenames
            %n     File name
            %s     Block size (for faster transfer)
            %S     Fundamental block size (for block counts)
            %t     Type in hex
            %T     Type in human readable form

       strings
           strings [-fo] [-t o|d|x] [-n LEN] [FILE]...

           Display printable strings in a binary file

                   -f              Precede strings with filenames
                   -o              Precede strings with octal offsets
                   -t o|d|x        Precede strings with offsets in base 8/10/16
                   -n LEN          At least LEN characters form a string (default 4)

       stty
           stty [-a|g] [-F DEVICE] [SETTING]...

           Without arguments, prints baud rate, line discipline, and deviations from stty sane

                   -F DEVICE       Open device instead of stdin
                   -a              Print all current settings in human-readable form
                   -g              Print in stty-readable form
                   [SETTING]       See manpage

       su  su [-lmp] [-s SH] [-] [USER [FILE ARGS | -c 'CMD' [ARG0 ARGS]]]

           Run shell under USER (by default, root)

                   -,-l    Clear environment, go to home dir, run shell as login shell
                   -p,-m   Do not set new $HOME, $SHELL, $USER, $LOGNAME
                   -c CMD  Command to pass to 'sh -c'
                   -s SH   Shell to use instead of user's default

       sulogin
           sulogin [-t N] [TTY]

           Single user login

                   -p      Start a login shell
                   -t SEC  Timeout

       svc svc [-udopchaitkx] SERVICE_DIR...

           Control services monitored by runsv supervisor

                   -u      If service is not running, start it; restart if it stops
                   -d      If service is running, send TERM+CONT signals; do not restart it
                   -o      Once: if service is not running, start it; do not restart it
                   -pchaitk Send STOP, CONT, HUP, ALRM, INT, TERM, KILL signal to service
                   -x      Exit: runsv will exit as soon as the service is down

       svok
           svok SERVICE_DIR

           Check whether runsv supervisor is running.  Exit code is 0 if it does, 100 if it does
           not, 111 (with error message) if SERVICE_DIR does not exist.

       swapoff
           swapoff [-a] [DEVICE]

           Stop swapping on DEVICE

                   -a      Stop swapping on all swap devices

       swapon
           swapon [-a] [-e] [-d[POL]] [DEVICE]

           Start swapping on DEVICE

                   -a      Start swapping on all swap devices
                   -d[POL] Discard blocks at swapon (POL=once),
                           as freed (POL=pages), or both (POL omitted)
                   -e      Silently skip devices that do not exist

       switch_root
           switch_root [-c CONSOLE_DEV] NEW_ROOT NEW_INIT [ARGS]

           Free initramfs and switch to another root fs:

           chroot to NEW_ROOT, delete all in /, move NEW_ROOT to /, execute NEW_INIT. PID must be
           1. NEW_ROOT must be a mountpoint.

                   -c DEV  Reopen stdio to DEV after switch

       sync
           sync [-df] [FILE]...

           Write all buffered blocks (in FILEs) to disk      -d   Avoid syncing metadata
                -f   Sync filesystems underlying FILEs

       sysctl
           sysctl [-enq] { -a | -p [FILE]... | [-w] [KEY[=VALUE]]... }

           Show/set kernel parameters

                   -e      Don't warn about unknown keys
                   -n      Don't show key names
                   -q      Quiet
                   -a      Show all values
                   -p      Set values from FILEs (default /etc/sysctl.conf)
                   -w      Set values

       syslogd
           syslogd [OPTIONS]

           System logging utility

                   -n              Run in foreground
                   -R HOST[:PORT]  Log to HOST:PORT (default PORT:514)
                   -L              Log locally and via network (default is network only if -R)
                   -C[size_kb]     Log to shared mem buffer (use logread to read it)
                   -O FILE         Log to FILE (default: /var/log/messages, stdout if -)
                   -s SIZE         Max size (KB) before rotation (default 200KB, 0=off)
                   -b N            N rotated logs to keep (default 1, max 99, 0=purge)
                   -l N            Log only messages more urgent than prio N (1-8)
                   -S              Smaller output
                   -t              Strip client-generated timestamps
                   -D              Drop duplicates
                   -f FILE         Use FILE as config (default:/etc/syslog.conf)

       tac tac [FILE]...

           Concatenate FILEs and print them in reverse

       tail
           tail [OPTIONS] [FILE]...

           Print last 10 lines of FILEs (or stdin) to.  With more than one FILE, precede each
           with a filename header.

                   -c [+]N[bkm]    Print last N bytes
                   -n N[bkm]       Print last N lines
                   -n +N[bkm]      Start on Nth line and print the rest
                                   (b:*512 k:*1024 m:*1024^2)
                   -q              Never print headers
                   -v              Always print headers
                   -f              Print data as file grows
                   -F              Same as -f, but keep retrying
                   -s SECONDS      Wait SECONDS between reads with -f

       tar tar c|x|t [-ZzJjahmvokO] [-f TARFILE] [-C DIR] [FILE]...

           Create, extract, or list files from a tar file

                   c       Create
                   x       Extract
                   t       List
                   -f FILE Name of TARFILE ('-' for stdin/out)
                   -C DIR  Change to DIR before operation
                   -v      Verbose
                   -O      Extract to stdout
                   -m      Don't restore mtime
                   -o      Don't restore user:group
                   -k      Don't replace existing files
                   -Z      (De)compress using compress
                   -z      (De)compress using gzip
                   -J      (De)compress using xz
                   -j      (De)compress using bzip2
                   --lzma  (De)compress using lzma
                   -a      (De)compress based on extension
                   -h      Follow symlinks
                   --overwrite             Replace existing files
                   --strip-components NUM  NUM of leading components to strip
                   --no-recursion          Don't descend in directories
                   --numeric-owner         Use numeric user:group
                   --no-same-permissions   Don't restore access permissions
                   --to-command COMMAND    Pipe files to COMMAND

       taskset
           taskset [-ap] [HEXMASK | -c LIST] { PID | PROG ARGS }

           Set or get CPU affinity

                   -p      Operate on PID
                   -a      Operate on all threads
                   -c      Affinity is a list, not mask

       tc  tc OBJECT CMD [dev STRING]

           OBJECT: qdisc|class|filter CMD: add|del|change|replace|show

           qdisc [handle QHANDLE] [root|ingress|parent CLASSID]      [[QDISC_KIND]
           [help|OPTIONS]]      QDISC_KIND := [p|b]fifo|tbf|prio|cbq|red|etc.  qdisc show [dev
           STRING] [ingress] class [classid CLASSID] [root|parent CLASSID]      [[QDISC_KIND]
           [help|OPTIONS] ] class show [ dev STRING ] [root|parent CLASSID] filter [pref PRIO]
           [protocol PROTO]      [root|classid CLASSID] [handle FILTERID]      [[FILTER_TYPE]
           [help|OPTIONS]] filter show [dev STRING] [root|parent CLASSID]

       tee tee [-ai] [FILE]...

           Copy stdin to each FILE, and also to stdout

                   -a      Append to the given FILEs, don't overwrite
                   -i      Ignore interrupt signals (SIGINT)

       telnet
           telnet [-a] [-l USER] HOST [PORT]

           Connect to telnet server

                   -a      Automatic login with $USER variable
                   -l USER Automatic login as USER

       telnetd
           telnetd [OPTIONS]

           Handle incoming telnet connections

                   -l LOGIN        Exec LOGIN on connect
                   -f ISSUE_FILE   Display ISSUE_FILE instead of /etc/issue
                   -K              Close connection as soon as login exits
                                   (normally wait until all programs close slave pty)
                   -p PORT         Port to listen on. Default 23
                   -b ADDR[:PORT]  Address to bind to
                   -F              Run in foreground
                   -i              Inetd mode

       tftp
           tftp [OPTIONS] HOST [PORT]

           Transfer a file from/to tftp server

                   -l FILE Local FILE
                   -r FILE Remote FILE
                   -g      Get file
                   -p      Put file
                   -b SIZE Transfer blocks in bytes

       time
           time [-vpa] [-o FILE] PROG ARGS

           Run PROG, display resource usage when it exits

                   -v      Verbose
                   -p      POSIX output format
                   -f FMT  Custom format
                   -o FILE Write result to FILE
                   -a      Append (else overwrite)

       timeout
           timeout [-s SIG] [-k KILL_SECS] SECS PROG ARGS

           Run PROG. Send SIG to it if it is not gone in SECS seconds.  Default SIG: TERM.If it
           still exists in KILL_SECS seconds, send KILL.

       top top [-bH] [-n COUNT] [-d SECONDS]

           Show a view of process activity in real time.  Read the status of all processes from
           /proc each SECONDS and show a screenful of them.  Keys:

                   N/M/P/T: sort by pid/mem/cpu/time
                   R: reverse sort
                   H: toggle threads
                   Q,^C: exit
           Options:

                   -b      Batch mode
                   -n N    Exit after N iterations
                   -d SEC  Delay between updates
                   -H      Show threads

       touch
           touch [-cham] [-d DATE] [-t DATE] [-r FILE] FILE...

           Update mtime of FILEs

                   -c      Don't create files
                   -h      Don't follow links
                   -a      Change only atime
                   -m      Change only mtime
                   -d DT   Date/time to use
                   -t DT   Date/time to use
                   -r FILE Use FILE's date/time

       tr  tr [-cds] STRING1 [STRING2]

           Translate, squeeze, or delete characters from stdin, writing to stdout

                   -c      Take complement of STRING1
                   -d      Delete input characters coded STRING1
                   -s      Squeeze multiple output characters of STRING2 into one character

       traceroute
           traceroute [-46Flnrv] [-f 1ST_TTL] [-m MAXTTL] [-q PROBES] [-p PORT]      [-t TOS] [-w
           WAIT_SEC] [-s SRC_IP] [-i IFACE]      [-z PAUSE_MSEC] HOST [BYTES]

           Trace the route to HOST

                   -4,-6   Force IP or IPv6 name resolution
                   -F      Set don't fragment bit
                   -l      Display TTL value of the returned packet
                   -n      Print numeric addresses
                   -r      Bypass routing tables, send directly to HOST
                   -v      Verbose
                   -f N    First number of hops (default 1)
                   -m N    Max number of hops
                   -q N    Number of probes per hop (default 3)
                   -p N    Base UDP port number used in probes
                           (default 33434)
                   -s IP   Source address
                   -i IFACE Source interface
                   -t N    Type-of-service in probe packets (default 0)
                   -w SEC  Wait for a response (default 3)
                   -z MSEC Wait before each send

       traceroute6
           traceroute6 [-nrv] [-f 1ST_TTL] [-m MAXTTL] [-q PROBES] [-p PORT]      [-t TOS] [-w
           WAIT_SEC] [-s SRC_IP] [-i IFACE]      [-z PAUSE_MSEC] HOST [BYTES]

           Trace the route to HOST

                   -n      Print numeric addresses
                   -r      Bypass routing tables, send directly to HOST
                   -v      Verbose
                   -f N    First number of hops (default 1)
                   -m N    Max number of hops
                   -q N    Number of probes per hop (default 3)
                   -p N    Base UDP port number used in probes
                           (default 33434)
                   -s IP   Source address
                   -i IFACE Source interface
                   -t N    Type-of-service in probe packets (default 0)
                   -w SEC  Wait for a response (default 3)
                   -z MSEC Wait before each send

       truncate
           truncate [-c] -s SIZE FILE...

           Truncate FILEs to SIZE

                   -c      Do not create files
                   -s SIZE

       ts  ts [-is] [STRFTIME]

           Pipe stdin to stdout, add timestamp to each line

                   -s      Time since start
                   -i      Time since previous line

       tty tty [-s]

           Print file name of stdin's terminal

                   -s      Print nothing, only return exit status

       tunctl
           tunctl [-f DEVICE] [-t NAME | -d NAME]

           Create or delete TUN/TAP interfaces

                   -f DEV  TUN device (default /dev/net/tun)
                   -t NAME Create iface (default: tapN)
                   -d NAME Delete iface

       ubirename
           ubirename UBI_DEVICE OLD_VOLNAME NEW_VOLNAME [OLD2 NEW2]...

           Rename UBI volumes on UBI_DEVICE

       udhcpc
           udhcpc [-fbqRB] [-a[MSEC]] [-t N] [-T SEC] [-A SEC|-n]      [-i IFACE] [-s PROG] [-p
           PIDFILE]      [-oC] [-r IP] [-V VENDOR] [-F NAME] [-x OPT:VAL]... [-O OPT]...

                   -i IFACE        Interface to use (default eth0)
                   -s PROG         Run PROG at DHCP events (default /etc/udhcpc/default.script)
                   -p FILE         Create pidfile
                   -B              Request broadcast replies
                   -t N            Send up to N discover packets (default 3)
                   -T SEC          Pause between packets (default 3)
                   -A SEC          Wait if lease is not obtained (default 20)
                   -b              Background if lease is not obtained
                   -n              Exit if lease is not obtained
                   -q              Exit after obtaining lease
                   -R              Release IP on exit
                   -f              Run in foreground
                   -S              Log to syslog too
                   -a[MSEC]        Validate offered address with ARP ping
                   -r IP           Request this IP address
                   -o              Don't request any options (unless -O is given)
                   -O OPT          Request option OPT from server (cumulative)
                   -x OPT:VAL      Include option OPT in sent packets (cumulative)
                                   Examples of string, numeric, and hex byte opts:
                                   -x hostname:bbox - option 12
                                   -x lease:3600 - option 51 (lease time)
                                   -x 0x3d:0100BEEFC0FFEE - option 61 (client id)
                                   -x 14:'"dumpfile"' - option 14 (shell-quoted)
                   -F NAME         Ask server to update DNS mapping for NAME
                   -V VENDOR       Vendor identifier (default 'udhcp VERSION')
                   -C              Don't send MAC as client identifier
           Signals:

                   USR1    Renew lease
                   USR2    Release lease

       udhcpd
           udhcpd [-fS] [-I ADDR] [-a MSEC] [CONFFILE]

           DHCP server

                   -f      Run in foreground
                   -S      Log to syslog too
                   -I ADDR Local address
                   -a MSEC Timeout for ARP ping (default 2000)
           Signals:

                   USR1    Update lease file

       uevent
           uevent [PROG ARGS]

           uevent runs PROG for every netlink notification.  PROG's environment contains data
           passed from the kernel.  Typical usage (daemon for dynamic device node creation):
                # uevent mdev & mdev -s

       umount
           umount [-rlfda] [-t FSTYPE] FILESYSTEM|DIRECTORY

           Unmount filesystems

                   -a      Unmount all filesystems
                   -r      Remount devices read-only if mount is busy
                   -l      Lazy umount (detach filesystem)
                   -f      Force umount (i.e., unreachable NFS server)
                   -d      Free loop device if it has been used
                   -t FSTYPE[,...] Unmount only these filesystem type(s)

       uname
           uname [-amnrspvio]

           Print system information

                   -a      Print all
                   -m      Machine (hardware) type
                   -n      Hostname
                   -r      Kernel release
                   -s      Kernel name (default)
                   -p      Processor type
                   -v      Kernel version
                   -i      Hardware platform
                   -o      OS name

       uncompress
           uncompress [-cf] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Overwrite

       unexpand
           unexpand [-fa][-t N] [FILE]...

           Convert spaces to tabs, writing to stdout

                   -a      Convert all blanks
                   -f      Convert only leading blanks
                   -t N    Tabstops every N chars

       uniq
           uniq [-cduiz] [-f,s,w N] [FILE [OUTFILE]]

           Discard duplicate lines

                   -c      Prefix lines by the number of occurrences
                   -d      Only print duplicate lines
                   -u      Only print unique lines
                   -i      Ignore case
                   -z      NUL terminated output
                   -f N    Skip first N fields
                   -s N    Skip first N chars (after any skipped fields)
                   -w N    Compare N characters in line

       unix2dos
           unix2dos [-ud] [FILE]

           Convert FILE in-place from Unix to DOS format.  When no file is given, use
           stdin/stdout.

                   -u      dos2unix
                   -d      unix2dos

       unlink
           unlink FILE

           Delete FILE by calling unlink()

       unlzma
           unlzma [-cfk] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       unshare
           unshare [OPTIONS] [PROG ARGS]

                   -m,--mount[=FILE]       Unshare mount namespace
                   -u,--uts[=FILE]         Unshare UTS namespace (hostname etc.)
                   -i,--ipc[=FILE]         Unshare System V IPC namespace
                   -n,--net[=FILE]         Unshare network namespace
                   -p,--pid[=FILE]         Unshare PID namespace
                   -U,--user[=FILE]        Unshare user namespace
                   -f                      Fork before execing PROG
                   -r                      Map current user to root (implies -U)
                   --mount-proc[=DIR]      Mount /proc filesystem first (implies -m)
                   --propagation slave|shared|private|unchanged
                                           Modify mount propagation in mount namespace
                   --setgroups allow|deny  Control the setgroups syscall in user namespaces

       unxz
           unxz [-cfk] [FILE]...

           Decompress FILEs (or stdin)

                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       unzip
           unzip [-lnojpqK] FILE[.zip] [FILE]... [-x FILE]... [-d DIR]

           Extract FILEs from ZIP archive

                   -l      List contents (with -q for short form)
                   -n      Never overwrite files (default: ask)
                   -o      Overwrite
                   -j      Do not restore paths
                   -p      Write to stdout
                   -t      Test
                   -q      Quiet
                   -K      Do not clear SUID bit
                   -x FILE Exclude FILEs
                   -d DIR  Extract into DIR

       uptime
           uptime

           Display the time since the last boot

       usleep
           usleep N

           Pause for N microseconds

       uudecode
           uudecode [-o OUTFILE] [INFILE]

           Uudecode a file Finds OUTFILE in uuencoded source unless -o is given

       uuencode
           uuencode [-m] [FILE] STORED_FILENAME

           Uuencode FILE (or stdin) to stdout

                   -m      Use base64 encoding per RFC1521

       vconfig
           vconfig COMMAND [OPTIONS]

           Create and remove virtual ethernet devices

                   add IFACE VLAN_ID
                   rem VLAN_NAME
                   set_flag IFACE 0|1 VLAN_QOS
                   set_egress_map VLAN_NAME SKB_PRIO VLAN_QOS
                   set_ingress_map VLAN_NAME SKB_PRIO VLAN_QOS
                   set_name_type NAME_TYPE

       vi  vi [-c CMD] [-R] [-H] [FILE]...

           Edit FILE

                   -c CMD  Initial command to run ($EXINIT and ~/.exrc also available)
                   -R      Read-only
                   -H      List available features

       w   w

           Show who is logged on

       watch
           watch [-n SEC] [-t] PROG ARGS

           Run PROG periodically

                   -n SEC  Period (default 2)
                   -t      Don't print header

       watchdog
           watchdog [-t N[ms]] [-T N[ms]] [-F] DEV

           Periodically write to watchdog device DEV

                   -T N    Reboot after N seconds if not reset (default 60)
                   -t N    Reset every N seconds (default 30)
                   -F      Run in foreground

           Use 500ms to specify period in milliseconds

       wc  wc [-cmlwL] [FILE]...

           Count lines, words, and bytes for FILEs (or stdin)

                   -c      Count bytes
                   -m      Count characters
                   -l      Count newlines
                   -w      Count words
                   -L      Print longest line length

       wget
           wget [-cqS] [--spider] [-O FILE] [-o LOGFILE] [--header STR]      [--post-data STR |
           --post-file FILE] [-Y on/off]      [--no-check-certificate] [-P DIR] [-U AGENT] URL...

           Retrieve files via HTTP or FTP

                   --spider        Only check URL existence: $? is 0 if exists
                   --header STR    Add STR (of form 'header: value') to headers
                   --post-data STR Send STR using POST method
                   --post-file FILE        Send FILE using POST method
                   --no-check-certificate  Don't validate the server's certificate
                   -c              Continue retrieval of aborted transfer
                   -q              Quiet
                   -P DIR          Save to DIR (default .)
                   -S              Show server response
                   -O FILE         Save to FILE ('-' for stdout)
                   -o LOGFILE      Log messages to FILE
                   -U STR          Use STR for User-Agent header
                   -Y on/off       Use proxy

       which
           which [-a] COMMAND...

           Locate COMMAND

                   -a      Show all matches

       who who [-aH]

           Show who is logged on

                   -a      Show all
                   -H      Print column headers

       whoami
           whoami

           Print the user name associated with the current effective user id

       xargs
           xargs [OPTIONS] [PROG ARGS]

           Run PROG on every item given by stdin

                   -0      NUL terminated input
                   -a FILE Read from FILE instead of stdin
                   -o      Reopen stdin as /dev/tty
                   -r      Don't run command if input is empty
                   -t      Print the command on stderr before execution
                   -p      Ask user whether to run each command
                   -E STR,-e[STR]  STR stops input processing
                   -I STR  Replace STR within PROG ARGS with input line
                   -n N    Pass no more than N args to PROG
                   -s N    Pass command line of no more than N bytes
                   -P N    Run up to N PROGs in parallel
                   -x      Exit if size is exceeded

       xxd xxd [-pri] [-g N] [-c N] [-l LEN] [-s OFS] [-o OFS] [FILE]

           Hex dump FILE (or stdin)

                   -g N            Bytes per group
                   -c N            Bytes per line
                   -p              Show only hex bytes, assumes -c30
                   -i              C include file style
                   -l LENGTH       Show only first LENGTH bytes
                   -s OFFSET       Skip OFFSET bytes
                   -o OFFSET       Add OFFSET to displayed offset
                   -r              Reverse (with -p, assumes no offsets in input)

       xz  xz -d [-cfk] [FILE]...

           Decompress FILEs (or stdin)

                   -d      Decompress
                   -c      Write to stdout
                   -f      Force
                   -k      Keep input files
                   -t      Test integrity

       xzcat
           xzcat [FILE]...

           Decompress to stdout

       yes yes [STRING]

           Repeatedly print a line with STRING, or 'y'

       zcat
           zcat [FILE]...

           Decompress to stdout

LIBC NSS

       GNU Libc (glibc) uses the Name Service Switch (NSS) to configure the behavior of the C
       library for the local environment, and to configure how it reads system data, such as
       passwords and group information.  This is implemented using an /etc/nsswitch.conf
       configuration file, and using one or more of the /lib/libnss_* libraries.  BusyBox tries
       to avoid using any libc calls that make use of NSS.  Some applets however, such as login
       and su, will use libc functions that require NSS.

       If you enable CONFIG_USE_BB_PWD_GRP, BusyBox will use internal functions to directly
       access the /etc/passwd, /etc/group, and /etc/shadow files without using NSS.  This may
       allow you to run your system without the need for installing any of the NSS configuration
       files and libraries.

       When used with glibc, the BusyBox 'networking' applets will similarly require that you
       install at least some of the glibc NSS stuff (in particular, /etc/nsswitch.conf,
       /lib/libnss_dns*, /lib/libnss_files*, and /lib/libresolv*).

       Shameless Plug: As an alternative, one could use a C library such as uClibc.  In addition
       to making your system significantly smaller, uClibc does not require the use of any NSS
       support files or libraries.

MAINTAINER

       Denis Vlasenko <vda.linux@googlemail.com>

AUTHORS

       The following people have contributed code to BusyBox whether they know it or not.  If you
       have written code included in BusyBox, you should probably be listed here so you can
       obtain your bit of eternal glory.  If you should be listed here, or the description of
       what you have done needs more detail, or is incorrect, please send in an update.

       Emanuele Aina <emanuele.aina@tiscali.it>

           run-parts

       Erik Andersen <andersen@codepoet.org>

           Tons of new stuff, major rewrite of most of the
           core apps, tons of new apps as noted in header files.
           Lots of tedious effort writing these boring docs that
           nobody is going to actually read.

       Laurence Anderson <l.d.anderson@warwick.ac.uk>

           rpm2cpio, unzip, get_header_cpio, read_gz interface, rpm

       Jeff Angielski <jeff@theptrgroup.com>

           ftpput, ftpget

       Edward Betts <edward@debian.org>

           expr, hostid, logname, whoami

       John Beppu <beppu@codepoet.org>

           du, nslookup, sort

       Brian Candler <B.Candler@pobox.com>

           tiny-ls(ls)

       Randolph Chung <tausq@debian.org>

           fbset, ping, hostname

       Dave Cinege <dcinege@psychosis.com>

           more(v2), makedevs, dutmp, modularization, auto links file,
           various fixes, Linux Router Project maintenance

       Jordan Crouse <jordan@cosmicpenguin.net>

           ipcalc

       Magnus Damm <damm@opensource.se>

           tftp client insmod powerpc support

       Larry Doolittle <ldoolitt@recycle.lbl.gov>

           pristine source directory compilation, lots of patches and fixes.

       Glenn Engel <glenne@engel.org>

           httpd

       Gennady Feldman <gfeldman@gena01.com>

           Sysklogd (single threaded syslogd, IPC Circular buffer support,
           logread), various fixes.

       Karl M. Hegbloom <karlheg@debian.org>

           cp_mv.c, the test suite, various fixes to utility.c, &c.

       Daniel Jacobowitz <dan@debian.org>

           mktemp.c

       Matt Kraai <kraai@alumni.cmu.edu>

           documentation, bugfixes, test suite

       Stephan Linz <linz@li-pro.net>

           ipcalc, Red Hat equivalence

       John Lombardo <john@deltanet.com>

           tr

       Glenn McGrath <bug1@iinet.net.au>

           Common unarchiving code and unarchiving applets, ifupdown, ftpgetput,
           nameif, sed, patch, fold, install, uudecode.
           Various bugfixes, review and apply numerous patches.

       Manuel Novoa III <mjn3@codepoet.org>

           cat, head, mkfifo, mknod, rmdir, sleep, tee, tty, uniq, usleep, wc, yes,
           mesg, vconfig, make_directory, parse_mode, dirname, mode_string,
           get_last_path_component, simplify_path, and a number trivial libbb routines

           also bug fixes, partial rewrites, and size optimizations in
           ash, basename, cal, cmp, cp, df, du, echo, env, ln, logname, md5sum, mkdir,
           mv, realpath, rm, sort, tail, touch, uname, watch, arith, human_readable,
           interface, dutmp, ifconfig, route

       Vladimir Oleynik <dzo@simtreas.ru>

           cmdedit; xargs(current), httpd(current);
           ports: ash, crond, fdisk, inetd, stty, traceroute, top;
           locale, various fixes
           and irreconcilable critic of everything not perfect.

       Bruce Perens <bruce@pixar.com>

           Original author of BusyBox in 1995, 1996. Some of his code can
           still be found hiding here and there...

       Tim Riker <Tim@Rikers.org>

           bug fixes, member of fan club

       Kent Robotti <robotti@metconnect.com>

           reset, tons and tons of bug reports and patches.

       Chip Rosenthal <chip@unicom.com>, <crosenth@covad.com>

           wget - Contributed by permission of Covad Communications

       Pavel Roskin <proski@gnu.org>

           Lots of bugs fixes and patches.

       Gyepi Sam <gyepi@praxis-sw.com>

           Remote logging feature for syslogd

       Linus Torvalds <torvalds@transmeta.com>

           mkswap, fsck.minix, mkfs.minix

       Mark Whitley <markw@codepoet.org>

           grep, sed, cut, xargs(previous),
           style-guide, new-applet-HOWTO, bug fixes, etc.

       Charles P. Wright <cpwright@villagenet.com>

           gzip, mini-netcat(nc)

       Enrique Zanardi <ezanardi@ull.es>

           tarcat (since removed), loadkmap, various fixes, Debian maintenance

       Tito Ragusa <farmatito@tiscali.it>

           devfsd and size optimizations in strings, openvt and deallocvt.

       Paul Fox <pgf@foxharp.boston.ma.us>

           vi editing mode for ash, various other patches/fixes

       Roberto A. Foglietta <me@roberto.foglietta.name>

           port: dnsd

       Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>

           misc

       Mike Frysinger <vapier@gentoo.org>

           initial e2fsprogs, printenv, setarch, sum, misc

       Jie Zhang <jie.zhang@analog.com>

           fixed two bugs in msh and hush (exitcode of killed processes)