NAME

       deb-version - Debian package version number format

SYNOPSIS

       [epoch:]upstream-version[-debian-revision]

DESCRIPTION

       Version numbers as used for Debian binary and source packages consist of three components.  These are:

       epoch
           This is a single (generally small) unsigned integer.  It may be omitted, in which case zero is
           assumed.  If it is omitted then the upstream-version may not contain any colons.

           It is provided to allow mistakes in the version numbers of older versions of a package, and also a
           package's previous version numbering schemes, to be left behind.

       upstream-version
           This is the main part of the version number.  It is usually the version number of the original
           (“upstream”) package from which the .deb file has been made, if this is applicable.  Usually this
           will be in the same format as that specified by the upstream author(s); however, it may need to be
           reformatted to fit into the package management system's format and comparison scheme.

           The comparison behavior of the package management system with respect to the upstream-version is
           described below.  The upstream-version portion of the version number is mandatory.

           The upstream-version may contain only alphanumerics (“A-Za-z0-9”) and the characters . + - : ~ (full
           stop, plus, hyphen, colon, tilde) and should start with a digit.  If there is no debian-revision then
           hyphens are not allowed; if there is no epoch then colons are not allowed.

       debian-revision
           This part of the version number specifies the version of the Debian package based on the upstream
           version.  It may contain only alphanumerics and the characters + . ~ (plus, full stop, tilde) and is
           compared in the same way as the upstream-version is.

           It is optional; if it isn't present then the upstream-version may not contain a hyphen.  This format
           represents the case where a piece of software was written specifically to be turned into a Debian
           package, and so there is only one “debianization” of it and therefore no revision indication is
           required.

           It is conventional to restart the debian-revision at ‘1’ each time the upstream-version is increased.

           Dpkg will break the version number apart at the last hyphen in the string (if there is one) to
           determine the upstream-version and debian-revision.  The absence of a debian-revision compares
           earlier than the presence of one (but note that the debian-revision is the least significant part of
           the version number).

   Sorting algorithm
       The upstream-version and debian-revision parts are compared by the package management system using the
       same algorithm:

       The strings are compared from left to right.

       First the initial part of each string consisting entirely of non-digit characters is determined.  These
       two parts (one of which may be empty) are compared lexically.  If a difference is found it is returned.
       The lexical comparison is a comparison of ASCII values modified so that all the letters sort earlier than
       all the non-letters and so that a tilde sorts before anything, even the end of a part.  For example, the
       following parts are in sorted order: ‘~~’, ‘~~a’, ‘~’, the empty part, ‘a’.

       Then the initial part of the remainder of each string which consists entirely of digit characters is
       determined.  The numerical values of these two parts are compared, and any difference found is returned
       as the result of the comparison.  For these purposes an empty string (which can only occur at the end of
       one or both version strings being compared) counts as zero.

       These two steps (comparing and removing initial non-digit strings and initial digit strings) are repeated
       until a difference is found or both strings are exhausted.

       Note that the purpose of epochs is to allow us to leave behind mistakes in version numbering, and to cope
       with situations where the version numbering scheme changes.  It is not intended to cope with version
       numbers containing strings of letters which the package management system cannot interpret (such as
       ‘ALPHA’ or ‘pre-’), or with silly orderings.

NOTES

       The tilde character and its special sorting properties were introduced in dpkg 1.10 and some parts of the
       dpkg build scripts only gained support for it later in the 1.10.x series.

SEE ALSO

       deb-control(5), deb(5), dpkg(1)