Provided by: nut-modbus_2.8.1-3.1ubuntu2_amd64 bug

NAME

       apc_modbus - Driver for APC Smart-UPS Modbus protocol

SUPPORTED HARDWARE

       Generally this driver should work for all the APC Modbus UPS devices. Some devices might
       expose more than is currently supported, like multiple phases. A general rule of thumb is
       that APC devices (or firmware versions) released after 2010 are more likely to support
       Modbus than the USB HID standard.

       Tested with the following hardware:

       •   SMT1500 (Smart-UPS 1500, Firmware 9.6)

       •   SMX750 (Smart-UPS X 750, Firmware 10.1)

       •   SMX1500 (Smart-UPS X 1500, Firmware 15.0)

       Note that you will have to enable Modbus communication. In the front panel of the UPS, go
       to Advanced Menu mode, under Configuration and enable Modbus.

           Note
           This driver was tested with Serial, TCP and USB interfaces for Modbus. Notably, the
           Serial ports are not available on all devices nowadays; the TCP support may require a
           purchase of an additional network management card; and the USB support currently
           requires a non-standard build of libmodbus (pull request against the upstream library
           is pending, as of at the time of this publication) as a pre-requisite to building NUT
           with this part of the support. For more details (including how to build the custom
           library and NUT with it) please see NUT PR #2063

           Note
           As currently published, this driver supports reading information from the UPS.
           Implementation of support to write (set modifiable variables or send commands) is
           expected with a later release. This can impact the host shutdown routines in
           particular (no ability to actively tell the UPS to power off or cycle in the end). As
           a workaround, you can try integrating apctest (from the "apcupsd" project) with a
           "Test to kill power" into your late-shutdown procedure, if needed.

EXTRA ARGUMENTS

       This driver also supports the following optional settings:

       port = string
           Some value must be set, typically auto.

               Note
               This could be a device filesystem path like /dev/usb/hiddev0 but current use of
               libusb API precludes knowing and matching by such identifiers. They may also be
               inherently unreliable (dependent on re-plugging and enumeration order). At this
               time the actual value is ignored, but syntactically some port configuration must
               still be there.

       It is possible to control multiple UPS units simultaneously by running several instances
       of this driver, provided they can be uniquely distinguished by setting some combination of
       the vendor, product, vendorid, productid, serial, bus and/or device options detailed
       below. For devices or operating systems that do not provide sufficient information, the
       allow_duplicates option can be of use (limited and risky!)

       vendorid = regex, productid = regex, vendor = regex, product = regex, serial = regex
           Select a specific UPS, in case there is more than one connected via USB. Each option
           specifies an extended regular expression (see regex(7) for more information on regular
           expressions), which must match the UPS’s entire respective vendor/product/serial
           string (minus any surrounding whitespace), or the whole 4-digit hexadecimal code for
           vendorid and productid.

           Try lsusb(8) or running this NUT driver with -DD command-line argument for finding out
           the strings to match.

           Examples:

           •   -x vendor="Foo.Corporation.*"

           •   -x vendorid="051d*" (APC)

           •   -x product=".*(Smart|Back)-?UPS.*"

       bus = regex
           Select a UPS on a specific USB bus or group of buses. The argument is a regular
           expression that must match the bus name where the UPS is connected (e.g.  bus="002" or
           bus="00[2-3]") as seen on Linux in /sys/bus/usb/devices or lsusb(8); including leading
           zeroes.

       device = regex
           Select a UPS on a specific USB device or group of devices. The argument is a regular
           expression that must match the device name where the UPS is connected (e.g.
           device="001" or device="00[1-2]") as seen on Linux in /sys/bus/usb/devices or
           lsusb(8); including leading zeroes.

               Note
               device numbers are not guaranteed by the OS to be stable across re-boots or device
               re-plugging.

       busport = regex
           If supported by the hardware, OS and libusb on the particular deployment, this option
           should allow to specify physical port numbers on an USB hub, rather than logical
           device enumeration values, and in turn — this should be less volatile across reboots
           or re-plugging. The value may be seen in the USB topology output of lsusb -tv on
           systems with that tool, for example.

               Note
               this option is not practically supported by some NUT builds (it should be ignored
               with a warning then), and not by all systems that NUT can run on.

       allow_duplicates
           If you have several UPS devices which may not be uniquely identified by the options
           above (e.g. only VID:PID can be discovered there), this flag allows each driver
           instance where it is set to take the first match if available, or proceed to try
           another.

           Normally the driver initialization would abort at this point claiming "Resource busy"
           or similar error, assuming that the otherwise properly matched device is unique — and
           some other process already handles it.

               Warning
               This feature is inherently non-deterministic! The association of driver instance
               name to actual device may vary between runs!

               If you only care to know that at least one of your no-name UPSes is online, this
               option can help.

               If you must really know which one, it will not!

       usb_set_altinterface = bAlternateSetting
           Force redundant call to usb_set_altinterface(), especially if needed for devices
           serving multiple USB roles where the UPS is not represented by the interface number 0
           (default).

       porttype=value
           Set the type of the port used. Available values are serial for RS232/485 based
           connections, tcp for TCP/IP connections and usb for USB connections.

       port=value
           Depending on the port type you can select a port here. For usb only auto is supported,
           for serial you can pass a device path like /dev/ttyS0 and for tcp you can pass a
           hostname with optional port like example.com:502.

       baudrate=num
           Set the speed of the serial connection. The default baudrate is 9600.

       parity=value
           Set the parity of the serial connection. Available values are N for none, E for even
           and O for odd. The default parity is N (none).

       databits=num
           Set the data bits of the serial connection. The default databits is 8.

       stopbits=num
           Set the stop bits of the serial connection. The default stopbits is 1.

       slaveid=num
           Set the Modbus slave id. The default slave id is 1.

       response_timeout_ms=num
           Set the Modbus response timeout. The default timeout is set by libmodbus. It can be
           good to set a higher timeout on TCP connections with high latency.

AUTHORS

       •   Axel Gembe <axel@gembe.net>

SEE ALSO

   The core driver
       nutupsdrv(8), ups.conf(5)

   Internet resources
       The NUT (Network UPS Tools) home page: https://www.networkupstools.org/