NAME

       ip-mptcp - MPTCP path manager configuration

SYNOPSIS

       ip [ OPTIONS ] mptcp { endpoint  | limits  | help  }

       ip mptcp endpoint add IFADDR [ port PORT ] [ dev IFNAME ] [ id ID ] [ FLAG-LIST ]

       ip mptcp endpoint delete id ID [ IFADDR ]

       ip mptcp endpoint change [ id ID ] [ IFADDR ] [ port PORT ] CHANGE-OPT

       ip mptcp endpoint show [ id ID ]

       ip mptcp endpoint flush

       FLAG-LIST := [ FLAG-LIST ] FLAG

       FLAG := [ signal | subflow | backup | fullmesh ]

       CHANGE-OPT := [ backup | nobackup | fullmesh | nofullmesh ]

       ip mptcp limits set [ subflow SUBFLOW_NR ] [ add_addr_accepted ADD_ADDR_ACCEPTED_NR ]

       ip mptcp limits show

       ip mptcp monitor

DESCRIPTION

       MPTCP is a transport protocol built on top of TCP that allows TCP connections to use multiple paths to
       maximize resource usage and increase redundancy. The ip-mptcp sub-commands allow configuring several
       aspects of the MPTCP path manager, which is in charge of subflows creation:

       The endpoint object specifies the IP addresses that will be used and/or announced for additional
       subflows:

       ip mptcp endpoint add      add new MPTCP endpoint
       ip mptcp endpoint delete   delete existing MPTCP endpoint
       ip mptcp endpoint show     get existing MPTCP endpoint
       ip mptcp endpoint flush    flush all existing MPTCP endpoints

       IFADDR An  IPv4  or IPv6 address. When used with the delete id operation, an IFADDR is only included when
              the ID is 0.

       PORT   When a port number is specified, incoming MPTCP subflows for  already  established  MPTCP  sockets
              will  be accepted on the specified port, regardless the original listener port accepting the first
              MPTCP subflow and/or this peer being actually on the client side.

       ID     is a unique numeric identifier for the given endpoint

       signal The endpoint will be announced/signaled to each  peer  via  an  MPTCP  ADD_ADDR  sub-option.  Upon
              reception  of  an  ADD_ADDR  sub-option,  the  peer  can  try  to  create additional subflows, see
              ADD_ADDR_ACCEPTED_NR.

       subflow
              If additional subflow creation is allowed by the MPTCP limits, the MPTCP path manager will try  to
              create  an additional subflow using this endpoint as the source address after the MPTCP connection
              is established.

       backup If this is a subflow endpoint, the subflows created using this endpoint will have the backup  flag
              set  during  the  connection  process.  This  flag instructs the peer to only send data on a given
              subflow when all non-backup subflows are unavailable. This does not affect  outgoing  data,  where
              subflow priority is determined by the backup/non-backup flag received from the peer

       fullmesh
              If  this is a subflow endpoint and additional subflow creation is allowed by the MPTCP limits, the
              MPTCP path manager will try to create an additional subflow for each  known  peer  address,  using
              this endpoint as the source address. This will occur after the MPTCP connection is established. If
              the  peer did not announce any additional addresses using the MPTCP ADD_ADDR sub-option, this will
              behave the same as a plain subflow endpoint. When the peer does announce addresses, each  received
              ADD_ADDR  sub-option  will  trigger  creation  of  an  additional  subflow to generate a full mesh
              topology.

       The limits object specifies the constraints for subflow creations:

       ip mptcp limits show   get current MPTCP subflow creation limits
       ip mptcp limits set    change the MPTCP subflow creation limits

       SUBFLOW_NR
              specifies the maximum number of additional subflows allowed for each MPTCP connection.  Additional
              subflows  can  be  created due to: incoming accepted ADD_ADDR sub-option, local subflow endpoints,
              additional subflows started by the peer.

       ADD_ADDR_ACCEPTED_NR
              specifies the maximum number of incoming ADD_ADDR sub-options accepted for each MPTCP  connection.
              After  receiving  the  specified  number  of  ADD_ADDR sub-options, any other incoming one will be
              ignored for the MPTCP connection lifetime. When an ADD_ADDR sub-option is accepted and  there  are
              no  local  fullmesh  endpoints,  the MPTCP path manager will try to create a new subflow using the
              address in the ADD_ADDR sub-option as the destination address  and  a  source  address  determined
              using  local routing resolution When fullmesh endpoints are available, the MPTCP path manager will
              try to create new subflows using each fullmesh  endpoint  as  a  source  address  and  the  peer's
              ADD_ADDR address as the destination.  In both cases the SUBFLOW_NR limit is enforced.

       monitor  displays  creation  and  deletion  of MPTCP connections as well as addition or removal of remote
       addresses and subflows.

AUTHOR

       Original Manpage by Paolo Abeni <pabeni@redhat.com>

iproute2                                           4 Apr 2020                                        IP-MPTCP(8)