Provided by: sg3-utils_1.46-3ubuntu4_amd64 
NAME
sg_logs - access log pages with SCSI LOG SENSE command
SYNOPSIS
sg_logs [--All] [--all] [--brief] [--filter=FL] [--hex] [--list] [--maxlen=LEN] [--name] [--no_inq]
[--page=PG] [--paramp=PP] [--pcb] [--ppc] [--pdt=DT] [--raw] [--readonly] [--sp] [--temperature]
[--transport] [--vendor=VP] [--verbose] DEVICE
sg_logs [--brief] [--filter=FL] [--hex] --in=FN [--name] [--pdt=DT] [--raw] [--vendor=VP]
sg_logs [--control=PC] [--in=FN] [--page=PG] [--raw] [--reset] --select [--sp] [--verbose] DEVICE
sg_logs [--enumerate] [--filter=FL] [--help] [--vendor=VP] [--version]
sg_logs [-a] [-A] [-b] [-D=DT] [-c=PC] [-e] [-f=FL] [-h] [-H] [-i=FN] [-l] [-L] [-m=LEN] [-M=VP] [-n]
[-p=PG] [-paramp=PP] [-pcb] [-ppc] [-r] [-R] [-select] [-sp] [-t] [-T] [-v] [-V] [-?] [-x] DEVICE
DESCRIPTION
This utility sends a SCSI LOG SENSE command to the DEVICE and then outputs the response. The LOG SENSE
command is used to fetch log pages which, if known, are decoded by default. When the --reset and/or
--select option is given then a SCSI LOG SELECT command is issued to the DEVICE. Alternatively one or
more log page responses can be in a file read using the --in=FN option; in this case those responses are
decoded and the DEVICE argument, if given, is ignored.
In SPC-4 revision 5 a subpage code was introduced to both the LOG SENSE and LOG SELECT command. At the
same time a page code field was introduced to the to the LOG SELECT command. The log subpage code can
range from 0 to 255 (0xff) inclusive. The subpage code value 255 can be thought of as a wildcard.
The SYNOPSIS section above is divided into five forms. The first form shows the options that can be used
to send a LOG SENSE command to the DEVICE and decode its response. The second form fetches data from a
file (named FN) and decodes it as if it were a response from a LOG SENSE command. The third form shows
the options that can be used to send a LOG SELECT command. The fourth form groups various management
options. The last form shows the older, deprecated command line interface which is maintained for
backward compatibility.
OPTIONS
Arguments to long options are mandatory for short options as well. The options are arranged in
alphabetical order based on the long option name.
-A, --All
fetch and decode all the log pages and subpages supported by the DEVICE. This requires a two
stage process: first the "supported log pages and subpages" log page is fetched, then for each
entry in its response, the corresponding log page (or subpage) is fetched and displayed. Note that
there are many SCSI devices that do not support LOG SENSE subpages and respond to this option with
an illegal request sense key (or ignored the subpage field).
-a, --all
outputs all the log pages supported by the DEVICE. This requires a two stage process: first the
"supported log pages" log page is fetched, then for each entry in its response, the corresponding
log page is fetched and displayed. When used twice (e.g. '-aa') all log pages and subpages are
fetched.
-b, --brief
shorten the amount of output for some log pages. For example the Tape Alert log page only outputs
parameters whose flags are set when --brief is given.
-c, --control=PC
accepts 0, 1, 2 or 3 for the PC argument:
0 : current threshold values
1 : current cumulative values
2 : default threshold values
3 : default cumulative values
The default value is 1 (i.e. current cumulative values).
-e, --enumerate
this option is used to output information held in this utility's internal tables about known log
pages including their name, acronym and fields. If given, the DEVICE argument is ignored. When
given once (e.g. '-e') all known pages are listed, sorted in ascending alphabetical acronym order.
When given twice, vendor pages are excluded. When given three times, all known pages are listed,
sorted in ascending numeric order listed; when given four times, vendor pages are excluded from
the numeric order.
The --filter=FL and --verbose options reduce the output of the enumeration.
-f, --filter=FL
FL is either a parameter code when DEVICE is given, or a peripheral device type (pdt) (or other)
if --enumerate is given.
In the parameter code case FL is a value between 0 and 65535 (0xffff) and only the parameter
section matching that code is output. If the --hex option is given the log parameter is output in
hexadecimal rather than decoding it. If the --hex option is used twice then the leading address on
each line of hex is removed. If the --raw option is given then the log parameter is output in
binary. Most log pages contain one or more log parameters. Examples of those that don't follow
that convention are those pages that list supported log pages (and subpages).
In the --enumerate case, when FL >= zero it is taken as a pdt value and only log pages associated
with that pdt plus generic pages listed in SPC are enumerated. If FL is -1 then the filter does
nothing which is the same as not giving this option; when FL is -2 then only generic pages listed
in SPC are enumerated. If FL is -10 then only generic direct access like (e.g. disk) pages are
enumerated. If FL is -11 then only generic tape like pages (e.g. includes ADC) are enumerated.
-h, --help
print out the usage message then exit.
-H, --hex
The default action is to decode known log page numbers (and subpage numbers) into text. When this
option is used once, the response is output in hexadecimal. When used twice, each line of hex has
the ASCII equivalent shown to the right. When used three times, the hex has no leading address nor
trailing ASCII making it suitable to be placed in a file (or piped). That file might later be used
by another invocation using the --in=FN option.
-i, --in=FN
This option may be used in two different contexts. One is with the --select to send a LOG SELECT
command to the given DEVICE; see the LOG SELECT section below.
The other context is with no DEVICE argument given in which case the contents of FN are decoded as
if it were the response of a LOG SENSE command (i.e. a log page). For decoding the page and
subpage numbers are taken from FN while the peripheral device type is either generic (i.e. from
SPC) or the value given by --pdt=DT.
FN is treated as a file name (or '-' for stdin) which contains ASCII hexadecimal or binary
representing a log page. The hexadecimal should be arranged as 1 or 2 digits representing a byte
each of which is whitespace or comma separated. Anything from and including a hash mark to the end
of line is ignored. If the --raw option is also given then FN is treated as binary.
-l, --list
lists the names of all logs sense pages supported by this device. This is done by reading the
"supported log pages" log page. When used twice (e.g. '-ll') lists the names of all logs sense
pages and subpages supported by this device, excluding pages whose subpage number is 0xff (apart
from page 0x0,0xff). When used three times then all supported pages and subpages reported by the
device are list. So the page/subpage names and not thrie content is shown with this option. There
is a list of common log page codes below.
-m, --maxlen=LEN
sets the "allocation length" field in the LOG SENSE cdb. The is the maximum length in bytes that
the response will be. Without this option (or LEN equal to 0) this utility first fetches the 4
byte response then does a second access with the length indicated in the first (4 byte) response.
Negative values and 1 for LEN are not accepted. LEN cannot exceed 65535 (0xffff). Responses can
be quite large (e.g. the background scan results log page) and this option can be used to limit
the amount of information returned.
-n, --name
decode some log pages into 'name=value' entries, one per line. The name contains no space and may
be abbreviated and the value is decimal unless prefixed by '0x'. Nesting is indicated by leading
spaces. This form is meant to be relatively easy to parse.
-x, --no_inq
suppresses the output of information obtained from an initial call to the INQUIRY command for the
standard response. The default (assuming some other options that suppress this output are also not
given) is to output several device identification strings.
If this option is given twice (or more) then no INQUIRY command is sent hence there will be no
device identification string output either. Also the peripheral device type (PDT) field will not
be obtained so this utility will not be able to differentiate between some log pages that are
device dependent. It will assume a PDT of 0 (i.e. a disk).
-O, --old
Switch to older style options. Please use as first option.
-p, --page=PG
log page name/number to access. PG is either an acronym, a page number, or a page, subpage number
pair. Available acronyms can be listed with the --enumerate option. Page (0 to 63) and subpage (0
to 255) numbers are comma separated. They are decimal unless a hexadecimal indication is given. A
hexadecimal number can be specified by a leading "0x" or a trailing "h".
A few acronyms specify a range of subpage values in which case the acronym may be followed by a
comma then a subpage number. This method can also be used to fetch the Supported subpages log page
(e.g. --page=temp,0xff).
-P, --paramp=PP
PP is the parameter pointer value to place in a field of that name in the LOG SENSE cdb. A decimal
number in the range 0 to 65535 (0xffff) is expected. When a value greater than 0 is given the
--ppc option should be selected. The default value is 0.
-q, --pcb
show Parameter Control Byte settings (only relevant when log parameters being output in ASCII).
-Q, --ppc
sets the Parameter Pointer Control (PPC) bit in the LOG SENSE cdb. Default is 0 (i.e. cleared).
This bit was made obsolete in SPC-4 revision 18.
-D, --pdt=DT
DT is the peripheral device type that is used when it is not available from the DEVICE. There are
two main cases of this: with the --pdt=DT without a DEVICE and when --no_inq is used with a
DEVICE.
-r, --raw
output the response in binary to stdout. Error messages and warnings are output to stderr.
This option may also be given together with --in=FN in which case the contents of FN are
interpreted as binary data (and the response is decoded as normal, not dumped as binary).
-R, --readonly
open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag). The default action is to try and
open DEVICE read-write then if that fails try to open again with read-only. However when a
read-write open succeeds there may still be unwanted actions on the close (e.g. some OSes try to
do a SYNCHRONIZE CACHE command). So this option forces a read-only open on DEVICE and if it fails,
this utility will exit. Note that options like --select most likely need a read-write open.
-R, --reset
use SCSI LOG SELECT command (with the PCR bit set) to reset the all log pages (or the given page).
Exactly what is reset depends on the accompanying SP bit (i.e. --sp option which defaults to 0)
and the PC ("page control") value (which defaults to 1). Supplying this option implies the
--select option as well. This option seems to clear error counter log pages but leaves pages like
self-test results, start-stop cycle counter and temperature log pages unaffected. This option may
be required to clear log pages if a counter reaches its maximum value since the log page in which
the counter is found will remain "stuck" at its maximum value until some user interaction (e.g.
calling sg_logs with this option).
-S, --select
use a LOG SELECT command. The default action (i.e. when neither this option nor --reset is given)
is to do a LOG SENSE command. See the LOG SELECT section.
-s, --sp
sets the Saving Parameters (SP) bit. Default is 0 (i.e. cleared). When set this instructs the
device to store the current log page parameters (as indicated by the DS and TSD parameter codes)
in some non-volatile location. Hence the log parameters will be preserved across power cycles.
This option is typically not needed, especially if the GLTSD flag is clear in the control mode
page as this instructs the device to periodically save all saveable log parameters to non-volatile
locations.
-t, --temperature
outputs the temperature. First looks in the temperature log page and if that is not available
tries the Informational Exceptions log page which may also have the current temperature
(especially on older disks).
-T, --transport
outputs the transport ('Protocol specific port') log page. Equivalent to setting '--page=18h'.
-M, --vendor=VP
where VP is a vendor/manufacturer (e.g. "sea" for Seagate) or product (group) acronym (e.g. "lto5"
for the 5th generation LTO (tape) consortium). Either the whole log page is vendor specific (e.g.
page numbers 0x30 to 0x3f) or part of a T10 defined log page is vendor specific. For example
SPC-5 defines parameter code 0x0 of page 0x2f (the Informational Exceptions log page) and states
that the remaining parameter codes (i.e. 0x1 to 0xffff) are vendor specific. Using a VP of "xxx"
will list the available acronyms.
If this option is used with --page=PG and PG is an acronym then this option is ignored. If PG is a
number (e.g. 0xc0) then VP is used to choose the which vendor specific page (e.g. sharing page
number 0xc0) to decode.
-v, --verbose
increase level of verbosity. When used with --enumerate, in the list of known log page names,
those that have no associated decode logic are followed by "[hex only]".
-V, --version
print out version string then exit.
LOG SELECT
The SCSI LOG SELECT command can be used to reset certain parameters to vendor specific defaults, save
them to non-volatile storage (i.e. the media), or supply new page contents. This command has changed
between SPC-3 and SPC-4 with the addition of the Page and Subpage Code fields which can only be non zero
when the Parameter list length is zero.
The --select (or --reset) option is required to issue a LOG SELECT command. If the --in=FN option is not
given (or FN is effectively empty) then the Parameter list length field is set to zero. If the --in=FN
option is is given then its decoded data is placed in the data-out buffer and its length in bytes is
placed in the Parameter list length field.
Other options that are active with the LOG SELECT command are --control=PC, --reset (which sets the PCR
bit) and --sp.
APPLICATION CLIENT
This is the name of a log page that acts as a container for data provided by the user. An application
client is a SCSI term for the program that issues commands to a SCSI initiator (often known as a Host Bus
Adapter (HBA)). So, for example, this utility is a SCSI application client.
The Application Client log page has 64 log parameters with parameters codes 0 to 63. Each can hold 252
bytes of user binary data. That 252 bytes (or less) of user data, with a 4 byte prefix (for a total of
256 bytes) can be provided with the --in=FN option. A typical prefix would be '0,n,83,fc'. The "n" is the
parameter code in hex so the last log parameter would be '0,3f,83,fc'. That log parameter could be read
back at some later time with '--page=0xf --filter=0x<n>'.
NOTES
This utility will usually do a double fetch of log pages with the SCSI LOG SENSE command. The first fetch
requests a 4 byte response (i.e. place 4 in the "allocation length" field in the cdb). From that response
it can calculate the actual length of the response which is what it asks for on the second fetch. This is
typical practice in SCSI and guaranteed to work in the standards. However some older devices don't
comply. For those devices using the --maxlen=LEN option will do a single fetch. A value of 252 should be
a safe starting point.
Various log pages hold information error rates, device temperature, start stop cycles since the device
was produced and the results of the last 20 self tests. Self tests can be initiated by the sg_senddiag(8)
utility. The smartmontools package provides much of the information found with sg_logs in a form
suitable for monitoring the health of SCSI disks and tape drives.
The simplest way to find which log pages can be decoded by this utility is to use the --enumerate option.
Some page names are known but there is no decode logic; such cases have "[hex only]" after the log page
name when the --verbose option is given with --enumerate.
EXIT STATUS
The exit status of sg_logs is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
OLDER COMMAND LINE OPTIONS
The options in this section were the only ones available prior to sg3_utils version 1.23 . Since then
this utility defaults to the newer command line options which can be overridden by using --old (or -O) as
the first option. See the ENVIRONMENT VARIABLES section for another way to force the use of these older
command line options.
Options with arguments or with two or more letters can have an extra '-' prepended. For example: both
'-pcb' and '--pcb' are acceptable.
-a outputs all the log pages supported by the device. Equivalent to --all in the main description.
-A outputs all the log pages and subpages supported by the device. Equivalent to '--all --all' in
the main description.
-c=PC Equivalent to --control=PC in the main description.
-e enumerate internal tables to show information about known log pages. Equivalent to --enumerate in
the main description.
-h suppresses decoding of known log sense pages and prints out the response in hex instead.
-i=FN FN is treated as a file name (or '-' for stdin) which contains ASCII hexadecimal representing a
log page that will be sent as parameter data of a LOG SELECT command. See the LOG SELECT section.
-H same action as '-h' in this section and equivalent to --hex in the main description.
-l lists the names of all logs sense pages supported by this device. Equivalent to --list in the
main description.
-L lists the names of all logs sense pages and subpages supported by this device. Equivalent to
'--list --list' in the main description.
-m=LEN request only LEN bytes of response data. Default is 0 which is interpreted as all that is
available. LEN is decimal unless it has a leading '0x' or trailing 'h'. Equivalent to
--maxlen=LEN in the main description.
-M=VP Equivalent to --vendor=VP in the main description.
-n Equivalent to --name in the main description.
-N, --new
Switch to the newer style options.
-p=PG log page code to access. PG is either an acronym, a page number, or a page, subpage pair.
Available acronyms can be listed with the --enumerate option. Page (0 to 3f) and subpage (0 to ff)
numbers are comma separated. The numbers are assumed to be hexadecimal.
-paramp=PP
PP is the parameter pointer value (in hex) to place in command. Should be a number between 0 and
ffff inclusive.
-pcb show Parameter Control Byte settings (only relevant when log parameters being output in ASCII).
-ppc sets the Parameter Pointer Control (PPC) bit. Default is 0 (i.e. cleared).
-r use SCSI LOG SELECT command (PCR bit set) to reset the all log pages (or the given page).
Equivalent to --reset in the main description.
-R Equivalent to --readonly in the main description.
-select
use a LOG SELECT command. Equivalent to --select in the main description.
-sp sets the Saving Parameters (SP) bit. Default is 0 (i.e. cleared). Equivalent to --sp in the main
description.
-t outputs the temperature. Equivalent to --temperature in the main description.
-T outputs the transport ('Protocol specific port') log page. Equivalent to --transport in the main
description.
-v increase level of verbosity.
-V print out version string then exit.
-x suppress the INQUIRY command. Equivalent to --no_inq in the main description.
-? output usage message then exit.
ENVIRONMENT VARIABLES
Since sg3_utils version 1.23 the environment variable SG3_UTILS_OLD_OPTS can be given. When it is present
this utility will expect the older command line options. So the presence of this environment variable is
equivalent to using --old (or -O) as the first command line option.
AUTHOR
Written by Douglas Gilbert
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2002-2020 Douglas Gilbert
This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
smartctl(smartmontools), sg_senddiag(8)
sg3_utils-1.45 January 2020 SG_LOGS(8)