Ubuntu Manpage: DS2760, DS2761, DS2762 - High-Precision Li+ Battery Monitor

Provided by: owfs-doc_3.2p4+dfsg1-4.3build2_all

NAME

       DS2760, DS2761, DS2762 - High-Precision Li+ Battery Monitor

SYNOPSIS

   Temperature Voltage and Current.
       30   [.]XXXXXXXXXXXX[XX][/[   amphours   |   current   |   currentbias   |   lock.[0-1|ALL]  |  memory  |
       pages/page.[0-1|ALL] | PIO | sensed | temperature | vbias | vis | volt | volthours |
       cc | ce | coc | defaultpmod | defaultswen | dc | de | doc | mstr | ov | ps | pmod | swen | uv |
       address | crc8 | id | locator | r_address | r_id | r_locator | type ]]

   Thermocouple
       30 [.]XXXXXXXXXXXX[XX][/[ temperature | typeX/range_low | typeX/range_high | typeX/temperature ]]

   Weather Station
       30 [.]XXXXXXXXXXXX[XX][/[ WS603/temperature | WS603/wind_speed | WS603/direction | WS603/volt |
       WS603/LED/status | WS603/LED/control.ALL | WS603/LED/model |
       WS603/calibrationwind_speed | WS603/calibration/direction |
       WS603/light/intensity | WS603/light/threshold

FAMILY CODE

SPECIAL PROPERTIES

amphours
read-write, floating point
Accumulated amperage read by current sensor. Units are in Amp-hr (Assumes internal 25mOhm resistor).
Derived from volthours / Rinternal.
Formally amphours is the integral of current - currentbias over time.

current
read-only, floating point
Current reading. Units are in Amp (Assumes internal 25 mOhm resistor). Derived from vis / Rinternal.

currentbias
read-write, floating point
Fixed offset applied to each current measurement. Used in the amphours value. Assumes internal 25mOhm
resistor. Units are Amp and range from -.08A to .08A.
Derived from vbias / Rinternal.

lock.[0-1|ALL]
read-write, yes-no
Lock either of the two eprom pages to prevent further writes. Apparently setting lock is permanent.

memory
read-write, binary
Access to the full 256 byte memory range. Much of this space is reserved or special use. User space is
the page area.
See the DATASHEET for a full memory map.

pages/pages.[0-1|ALL]
read-write, binary Two 16 byte areas of memory for user application. The lock property can prevent
further alteration.
NOTE that the page property is different from the common OWFS implementation in that all of memory is not
accessible.

PIO
write-only, yes-no
Controls the PIO pin allowing external switching.
Writing "1" turns the PIO pin on (conducting). Writing "0" makes the pin non-conducting. The logical
state of the voltage can be read with the sensed property. This will reflect the current voltage at the
pin, not the value sent to PIO
Note also that PIO will also be altered by the power-status of the DS2670 See the datasheet for details.

sensed
read-only, yes-no
The logical voltage at the PIO pin. Useful only if the PIO property is set to "0" (non-conducting).
Value will be 0 or 1 depending on the voltage threshold.

temperature
read-only, floating point
Temperature read by the chip at high resolution (~13 bits). Units are selected from the invoking command
line. See owfs(1) or owhttpd(1) for choices. Default is Celsius.
Conversion is continuous.

vbias
read-write, floating point
Fixed offset applied to each vis measurement. Used for the volthours value. Units are in Volts.
Range -2.0mV to 2.0mV

vis
read-only, floating point
Current sensor reading (unknown external resistor). Measures the voltage gradient between the Vis pins.
Units are in Volts
The vis readings are integrated over time to provide the volthours property.
The current reading is derived from vis assuming the internal 25 mOhm resistor is employed. There is no
way to know this through software.

volt
read-only, floating point
Voltage read at the voltage sensor;. This is separate from the vis voltage that is used for current
measurement. Units are Volts
Range is between 0 and 4.75V

volthours
read-write, floating point
Integral of vis - vbias over time. Units are in volthours

THERMOCOUPLE

   typeX/
       directory
       Thermocouple  circuit  using  the DS2760 to read the Seebeck voltage and the reference temperature. Since
       the type interpretation of the values read depends on the type of  thermocouple,  the  correct  directory
       must be chosen. Supported thermocouple types include types B, E, J, K, N, R, S and T.

   typeX/range_low typeX/ranges_high
       read-only, flaoting point
       The  lower and upper temperature supported by this thermocouple (at least by the conversion routines). In
       the globally chosen temperature units.

   typeX/temperature
       read-only, floating point
       Thermocouple temperature. Requires a voltage and temperature  conversion.  Returned  in  globally  chosen
       temperature units.
       Note:  there are two types of temperature measurements possible. The temperature value in the main device
       directory is the reference  temperature  read  at  the  chip.  The  typeX/temperature  value  is  at  the
       thermocouple junction, probably remote from the chip.

WEATHER STATION

WS603
directory
Weather station from AAG electronica that includes temperature, wind speed, wind direction, light sensor
and LED lights.

WS603/temperature
read-only, floating-point
Uses the DS2760 temperature sensor. This is equivalent to the temperature value. Again in the specificed
temperature scale, default Celsius.

WS603/wind_speed
read_only, floating-point
Readings from the anometer, scaled using the WS603/calibration/wind_speed

WS603/direction
read_only, unsigned integer
Wind direction, using the following table

1 N

2 NNE

3 NE

4 NEE

5 E

6 EES

7 ES

8 ESS

9 S

10 SSW

11 SW

12 SWW

13 W

14 WWN

15 WN

16 WWN

Values are adjusted (internally) by the WS603/calibration/direction property

WS603/volt
read-only, unsigned integer
Voltage value from the WS603 device. Units and significance is unclear.

WS603/calibration/wind_speed
read-write, unsigned integer
Value between 1 and 200 for wind speed scaling. Values on of this range are ignored and the default value
of 100 used.

WS603/calibration/direction
read-write, unsigned integer
Adjustment of wind direction. See datasheet.

WS603/light/intensity
read-only, unsigned integer
Uncalibrated value from an internal light sensor. Used for control of LED display (daytime vs nighttime).

WS603/light/threshold
read-only, unsigned integer
Threshold for internal light sensor. Used for control of LED display (daytime vs nighttime).

Value is set as value 4 of the array passed to WS603/LED/control

WS603/LED/status
read-only, unsigned integer
Status of LED lights intensities. See datasheet.

Value is set as values 2 and 3 of the array passed to WS603/LED/control

WS603/LED/model
read-only, unsigned integer
What factors control LED display. See datasheet.

Value is set as value 1 of the array passed to WS603/LED/control.ALL

WS603/LED/model
write-only, unsigned integer array of 4 values
Four integers sent to control LED display. All four values must be sent, comma separated.

0 Light mode

1 Light status

2 Light level

3 Light threshold

OBSCURE PROPERTIES

   cc ce coc dc de doc mstr ov pmod swen uv
       varies, yes-no
       Bit flags corresponding to various battery management functions  of  the  chip.  See  the  DATASHEET  for
       details of the identically named entries.
       In general, writing "0" corresponds to a 0 bit value, and non-zero corresponds to a 1 bit value.

   defaultpmod defaultswen
       read-write, yes-no
       Default power-on state for the corresponding properties.

STANDARD PROPERTIES

address
r_address
read-only, ascii
The entire 64-bit unique ID. Given as upper case hexadecimal digits (0-9A-F).
address starts with the family code
r address is the address in reverse order, which is often used in other applications and labeling.

crc8
read-only, ascii
The 8-bit error correction portion. Uses cyclic redundancy check. Computed from the preceding 56 bits of
the unique ID number. Given as upper case hexadecimal digits (0-9A-F).

family
read-only, ascii
The 8-bit family code. Unique to each type of device. Given as upper case hexadecimal digits (0-9A-F).

id
r_id
read-only, ascii
The 48-bit middle portion of the unique ID number. Does not include the family code or CRC. Given as
upper case hexadecimal digits (0-9A-F).
r id is the id in reverse order, which is often used in other applications and labeling.

locator
r_locator
read-only, ascii
Uses an extension of the 1-wire design from iButtonLink company that associated 1-wire physical
connections with a unique 1-wire code. If the connection is behind a Link Locator the locator will show a
unique 8-byte number (16 character hexadecimal) starting with family code FE.
If no Link Locator is between the device and the master, the locator field will be all FF.
r locator is the locator in reverse order.

present (DEPRECATED)
read-only, yes-no
Is the device currently present on the 1-wire bus?

type
read-only, ascii
Part name assigned by Dallas Semi. E.g. DS2401 Alternative packaging (iButton vs chip) will not be
distiguished.

ALARMS

       None.

DESCRIPTION

1-Wire
1-wire is a wiring protocol and series of devices designed and manufactured by Dallas Semiconductor, Inc.
The bus is a low-power low-speed low-connector scheme where the data line can also provide power.

Each device is uniquely and unalterably numbered during manufacture. There are a wide variety of devices,
including memory, sensors (humidity, temperature, voltage, contact, current), switches, timers and data
loggers. More complex devices (like thermocouple sensors) can be built with these basic devices. There
are also 1-wire devices that have encryption included.

The 1-wire scheme uses a single bus master and multiple slaves on the same wire. The bus master initiates
all communication. The slaves can be individually discovered and addressed using their unique ID.

Bus masters come in a variety of configurations including serial, parallel, i2c, network or USB adapters.

OWFS design
OWFS is a suite of programs that designed to make the 1-wire bus and its devices easily accessible. The
underlying principle is to create a virtual filesystem, with the unique ID being the directory, and the
individual properties of the device are represented as simple files that can be read and written.

Details of the individual slave or master design are hidden behind a consistent interface. The goal is to
provide an easy set of tools for a software designer to create monitoring or control applications. There
are some performance enhancements in the implementation, including data caching, parallel access to bus
masters, and aggregation of device communication. Still the fundamental goal has been ease of use,
flexibility and correctness rather than speed.

DS2760 DS2761 DS2762
The DS2760 (3) is a class of battery charging controllers. There are minor hardware difference between
the DS2760, DS2761 and DS2762 battery chip, but they are indistinguishable to the software.

A number of interesting devices can be built with the DS276x including thermocouples. Support for
thermocouples in built into the software, using the embedded thermister as the cold junction temperature.

For an explanation of the differences between the DS276x variants, see Dallas Application Note 221.

ADDRESSING

       All 1-wire devices are factory assigned a unique 64-bit address. This address is of the form:

       Family Code
              8 bits

       Address
              48 bits

       CRC    8 bits

       Addressing under OWFS is in hexadecimal, of form:

              01.123456789ABC

       where 01 is an example 8-bit family code, and 12345678ABC is an example 48 bit address.

       The dot is optional, and the CRC code can included. If included, it must be correct.

DATASHEET

       http://pdfserv.maxim-ic.com/en/ds/DS2760.pdf
       http://pdfserv.maxim-ic.com/en/an/app221.pdf
       http://www.aag.com.mx/aagusa/contents/en-us/Description%20of%20WSV3%20Interface%20(1-wire).pdf

AVAILABILITY

       http://www.owfs.org

AUTHOR

       Paul Alfille (paul.alfille@gmail.com)