Ubuntu Manpage: Error_handling - A set of routines for error handling in NCAR Graphics.

Provided by: libncarg-dev_6.6.2.dfsg.1-4_amd64

NAME

       Error_handling - A set of routines for error handling in NCAR Graphics.

SYNOPSIS

       ENTSR - Enters recovery mode.
       EPRIN - Prints the current error message.
       ERROF - Turns off the internal error flag.
       FDUM - A dump routine - the default version just RETURNS.
       ICFELL - Checks for an outstanding error condition.
       ICLOEM - Computes the real length of its character-string argument (ignoring blanks on the
       end)
       NERRO - Gets the current value of the internal error flag.
       RETSR - Restores a previous value of the internal error flag.
       SEMESS - Gets a specified portion of the current error message.
       SETER - Called by NCAR Graphics routines to report error conditions.

C-BINDING SYNOPSIS

       #include <ncarg/ncargC.h>

       c_entsr
       c_eprin
       c_errof
       c_icfell
       c_icloem
       c_nerro
       c_retsr
       c_semess
       c_seter

USING SETER IN NCAR GRAPHICS

There are specific conventions for the use of SETER within NCAR Graphics, as follows:

- All detectable errors shall be recoverable, in the sense described above. (That is,
in every call to SETER, the final argument shall be a 1, rather than a 2.) This is by
request of the folks doing NCAR Interactive, who rightly consider STOPs in the
utilities undesirable. The idea is to let the user decide what is to be done about the
various error conditions.

- Whenever an NCAR Graphics routine calls a lower-level routine that might detect an
error and call SETER, it should subsequently use ICFELL to check the error state; if a
recoverable error has occurred, it should first do required clean-up chores, if
possible, and then pass control back to the routine that called it. In all such uses
of ICFELL, the first argument should be the name of the routine referencing ICFELL and
the second argument should be a new number for the error, reflecting the position of
the reference to the lower-level routine in the upper-level routine.

- Any NCAR Graphics routine that can be called by a user and that can potentially yield
a call to SETER must immediately check the error state and, if that error state is
non-zero, return control without doing anything else. This is most conveniently done
using a reference to ICFELL; see the second example in the "Usage" section of the
description of ICFELL. All such references should have a first argument of the form
'XXXXXX - UNCLEARED PRIOR ERROR', where "XXXXXX" is the name of the routine in which
the reference occurs, and a second argument equal to "1".

- It is recommended that, within a given utility routine, the error numbers in
references to SETER and ICFELL should start at 1 and increment by 1. These numbers
generally have no intrinsic meaning in and of themselves: they are merely intended to
allow a consultant to find the reference that generated a given error.

- NCAR Graphics routines are not required to turn recovery mode on before calling a
lower-level routine that might call SETER (which was the convention in the PORT
library, as described in the PORT document). Instead, the assumption is that it is
the responsibility of the user of NCAR Graphics to set recovery mode if he/she desires
to do recovery. Since, by default, recovery mode is turned off, all NCAR Graphics
calls to SETER will be treated as fatal: the error message will be printed and
execution will be terminated. Once the user turns recovery mode on, however, no NCAR
Graphics error will be treated in this way except for one that the user fails to
recover from.

Note: These conventions are being adopted as of December 2, 1993, and represent a goal for
the future. The current situation is somewhat muddled: In some utilities, all SETER calls
are fatal ones. In other utilities, some SETER calls are fatal and some are not. In other
utilities, no SETER calls are fatal. In general, errors at a lower level are not detected
and passed back up the call chain. Users have complained (and rightly so) that error
recovery is, in general, not possible; observance of these conventions should help to fix
the situation.

Further note: As of March 30, 1994, the situation has improved markedly. CONPACK and all
utilities referenced by it have been updated to follow the guidelines given above and work
is proceeding on other utilities.

There is one sticky area in which questions remains to be answered: Sometimes, when an
error condition occurs during execution of a utility routine that has changed the internal
state of GKS or SPPS, it has not been possible to restore the state of those packages to
exactly what it was before that routine was entered. In some cases, better bookkeeping
would allow restoration to be done; in other cases, though, restoration would involve
calling a routine that could generate a call to SETER, which would cause a STOP. In the
latter cases, I have not yet worked out a good solution. For the moment, therefore, the
situation is this: if you call an NCAR Graphics utility with recovery mode turned on and,
when you get control back, you find that an error has occurred, you must be prepared to
deal with the possibility that at least the following things might been changed: 1) the
current SET call; 2) the current polyline color index; 3) the current polymarker color
index; 4) the current text color index; 5) the current fill area color index; 6) the
current dash pattern.

ACCESS

       To use the Error_handling C or Fortran routines, load the NCAR Graphics libraries ncarg,
       ncarg_gks, and ncarg_c, preferably in that order.

COPYRIGHT