Provided by: radvd_2.19-1ubuntu1_amd64 
NAME
radvd.conf - configuration file of the router advertisement daemon radvd
DESCRIPTION
This file describes the information which is included in the router advertisement (RA) of a specific
interface.
The file contains one or more interface definitions of the form:
interface name {
list of interface specific options
list of prefix definitions
list of clients (IPv6 addresses) to advertise to
list of route definitions
list of RDNSS definitions
list of DNSSL definitions
list of ABRO definitions
list of acceptable RA source addresses
};
All the possible interface specific options are detailed below. Each option has to be terminated by a
semicolon.
Prefix definitions are of the form:
prefix prefix/length {
list of prefix specific options
};
Prefix can be network prefix or the address of the interface. The address of interface should be used
when using Mobile IPv6 extensions.
Special prefix "::/64" is also supported on systems that implement getifaddrs() (on other systems,
configuration activation fails and radvd exits). When configured, radvd picks all non-link-local prefix
assigned to the interface and starts advertising it. This may be applicable in non-6to4 scenarios where
the upstream prefix might change. This option is incompatible with Base6to4Interface option.
AdvRouterAddr option is always enabled when this configuration is used.
All the possible prefix specific options are described below. Each option has to be terminated by a
semicolon.
Decimal values are allowed only for MinDelayBetweenRAs, MaxRtrAdvInterval and MinRtrAdvInterval. Decimal
values should be used only when using Mobile IPv6 extensions.
Route definitions are of the form:
route prefix/length {
list of route specific options
};
The prefix of a route definition should be network prefix; it can be used to advertise more specific
routes to the hosts.
RDNSS (Recursive DNS server) definitions are of the form:
RDNSS ip [ip] [ip] {
list of rdnss specific options
};
DNSSL (DNS Search List) definitions are of the form:
DNSSL suffix [suffix] [suffix] [...] {
list of dnssl specific options
};
By default radvd will send multicast route advertisements so that every node on the link can use them.
The list of clients (IPv6 address) to advertise to, and accept route solicitations from can be
configured. If done, radvd does not send send messages to the multicast addresses but to the configured
unicast addresses only. Solicitations from other addresses are refused. This is similar to UnicastOnly
but includes periodic messages and incoming client access configuration. See examples section for a use
case of this.
The definitions are of the form:
clients {
list of IPv6 addresses
};
By default radvd will use the first link-local address for the interface as the source address for route
advertisements. This can be overwritten by manually setting the list of acceptable source addresses. If
done, radvd will use the first address from the interface that is present in the configured source
addresses only. This functionality will NOT spoof the source address, but may be useful in combination
with VRRP or other functionality that
AdvRASrcAddress {
list of IPv6 addresses
};
ABRO (Authoritative Border Router Option) definitions are of the form:
abro IPv6-address {
list of abro specific options
};
INTERFACE SPECIFIC OPTIONS
IgnoreIfMissing on|off
A flag indicating whether or not the interface is ignored if it does not exist at start-up.
This is useful for dynamic interfaces which are not active when radvd starts or which are
dynamically disabled and re-enabled during the time radvd runs.
Current versions of radvd automatically try to re-enable interfaces.
Enabling IgnoreIfMissing also quenches certain warnings in log messages relating to missing
interfaces.
Default: on
AdvSendAdvert on|off
A flag indicating whether or not the router sends periodic router advertisements and responds to
router solicitations.
This option no longer has to be specified first, but it needs to be on to enable advertisement on
this interface.
Default: off
UnicastOnly on|off
Indicates that the interface link type only supports unicast. This will prevent unsolicited
advertisements from being sent, and will cause solicited advertisements to be unicast to the
soliciting node. This option is necessary for non-broadcast, multiple-access links, such as
ISATAP.
Default: off
AdvRASolicitedUnicast on|off
Indicates that router solicitations will be responded to with unicast router advertisements, as
recommended by RFC7772. Large networks with a high concentration of mobile devices might
experience like battery depletion, when solicited Router Advertisement messages are multicast.
This corresponds to the Cisco IOS option ipv6 nd ra solicited unicast
Default: on
MaxRtrAdvInterval seconds
The maximum time allowed between sending unsolicited multicast router advertisements from the
interface, in seconds.
Must be no less than 4 seconds and no greater than 1800 seconds.
Minimum when using Mobile IPv6 extensions: 0.07.
For values less than 0.2 seconds, 0.02 seconds is added to account for scheduling granularities as
specified in RFC3775.
Default: 600 seconds
MinRtrAdvInterval seconds
The minimum time allowed between sending unsolicited multicast router advertisements from the
interface, in seconds.
Must be no less than 3 seconds and no greater than 0.75 * MaxRtrAdvInterval.
Minimum when using Mobile IPv6 extensions: 0.03.
Default: 0.33 * MaxRtrAdvInterval
MinDelayBetweenRAs seconds
The minimum time allowed between sending multicast router advertisements from the interface, in
seconds.
This applies to solicited multicast RAs. This is defined as the protocol constant
MIN_DELAY_BETWEEN_RAS in RFC4861. MIPv6 redefines this parameter to have a minimum of 0.03
seconds.
Minimum when using Mobile IPv6 extensions: 0.03.
Default: 3
AdvManagedFlag on|off
When set, hosts use the administered (stateful) protocol for address autoconfiguration in addition
to any addresses autoconfigured using stateless address autoconfiguration. The use of this flag
is described in RFC 4862.
Default: off
AdvOtherConfigFlag on|off
When set, hosts use the administered (stateful) protocol for autoconfiguration of other (non-
address) information. The use of this flag is described in RFC 4862.
Default: off
AdvLinkMTU integer
The MTU option is used in router advertisement messages to insure that all nodes on a link use
the same MTU value in those cases where the link MTU is not well known.
If specified, i.e. not 0, must not be smaller than 1280 and not greater than the maximum MTU
allowed for this link (e.g. ethernet has a maximum MTU of 1500. See RFC 4864).
Default: 0
AdvReachableTime milliseconds
The time, in milliseconds, that a node assumes a neighbor is reachable after having received a
reachability confirmation. Used by the Neighbor Unreachability Detection algorithm (see Section
7.3 of RFC 4861). A value of zero means unspecified (by this router).
Must be no greater than 3,600,000 milliseconds (1 hour).
Default: 0
AdvRetransTimer milliseconds
The time, in milliseconds, between retransmitted Neighbor Solicitation messages. Used by address
resolution and the Neighbor Unreachability Detection algorithm (see Sections 7.2 and 7.3 of RFC
4861). A value of zero means unspecified (by this router).
Default: 0
AdvCurHopLimit integer
The default value that should be placed in the Hop Count field of the IP header for outgoing
(unicast) IP packets. The value should be set to the current diameter of the Internet. The value
zero means unspecified (by this router).
Default: 64
AdvDefaultLifetime seconds
The lifetime associated with the default router in units of seconds. The maximum value
corresponds to 18.2 hours. A lifetime of 0 indicates that the router is not a default router and
should not appear on the default router list. The router lifetime applies only to the router's
usefulness as a default router; it does not apply to information contained in other message fields
or options. Options that need time limits for their information include their own lifetime
fields.
Must be either zero or between MaxRtrAdvInterval and 9000 seconds.
Default: 3 * MaxRtrAdvInterval (Minimum 1 second).
AdvDefaultPreference low|medium|high
The preference associated with the default router, as either "low", "medium", or "high".
Default: medium
AdvSourceLLAddress on|off
When set, the link-layer address of the outgoing interface is included in the RA.
Default: on
AdvHomeAgentFlag on|off
When set, indicates that sending router is able to serve as Mobile IPv6 Home Agent. When set,
minimum limits specified by Mobile IPv6 are used for MinRtrAdvInterval and MaxRtrAdvInterval.
Default: off
AdvHomeAgentInfo on|off
When set, Home Agent Information Option (specified by Mobile IPv6) is included in Router
Advertisements. AdvHomeAgentFlag must also be set when using this option.
Default: off
HomeAgentLifetime seconds
The length of time in seconds (relative to the time the packet is sent) that the router is
offering Mobile IPv6 Home Agent services. A value 0 must not be used. The maximum lifetime is
65520 seconds (18.2 hours). This option is ignored, if AdvHomeAgentInfo is not set.
If both HomeAgentLifetime and HomeAgentPreference are set to their default values, Home Agent
Information Option will not be sent.
Default: AdvDefaultLifetime
HomeAgentPreference integer
The preference for the Home Agent sending this Router Advertisement. Values greater than 0
indicate more preferable Home Agent, values less than 0 indicate less preferable Home Agent. This
option is ignored, if AdvHomeAgentInfo is not set.
If both HomeAgentLifetime and HomeAgentPreference are set to their default values, Home Agent
Information Option will not be sent.
Default: 0
AdvMobRtrSupportFlag on|off
When set, the Home Agent signals it supports Mobile Router registrations (specified by NEMO
Basic). AdvHomeAgentInfo must also be set when using this option.
Default: off
AdvIntervalOpt on|off
When set, Advertisement Interval Option (specified by Mobile IPv6) is included in Router
Advertisements. When set, minimum limits specified by Mobile IPv6 are used for MinRtrAdvInterval
and MaxRtrAdvInterval.
The advertisement interval is based on the configured MaxRtrAdvInterval parameter except where
this is less than 200ms. In this case, the advertised interval is ( MaxRtrAdvInterval + 20ms ).
Default: off
PREFIX SPECIFIC OPTIONS
AdvOnLink on|off
When set, indicates that this prefix can be used for on-link determination. When not set the
advertisement makes no statement about on-link or off-link properties of the prefix. For
instance, the prefix might be used for address configuration with some of the addresses belonging
to the prefix being on-link and others being off-link.
Default: on
AdvAutonomous on|off
When set, indicates that this prefix can be used for autonomous address configuration as specified
in RFC 4862.
Default: on
AdvRouterAddr on|off
When set, indicates that the address of interface is sent instead of network prefix, as is
required by Mobile IPv6. When set, minimum limits specified by Mobile IPv6 are used for
MinRtrAdvInterval and MaxRtrAdvInterval.
Default: off
AdvValidLifetime seconds|infinity
The length of time in seconds (relative to the time the packet is sent) that the prefix is valid
for the purpose of on-link determination. The symbolic value infinity represents infinity (i.e. a
value of all one bits (0xffffffff)). The valid lifetime is also used by RFC 4862.
Note that clients will ignore AdvValidLifetime of an existing prefix if the lifetime is below two
hours, as required in RFC 4862 Section 5.5.3 point e).
Note: RFC4861's suggested default value is significantly longer: 30 days.
Default: 86400 seconds (1 day)
AdvPreferredLifetime seconds|infinity
The length of time in seconds (relative to the time the packet is sent) that addresses generated
from the prefix via stateless address autoconfiguration remain preferred. The symbolic value
infinity represents infinity (i.e. a value of all one bits (0xffffffff)). See RFC 4862.
Note: RFC4861's suggested default value is significantly longer: 7 days.
Default: 14400 seconds (4 hours)
DeprecatePrefix on|off
Upon shutdown, this option will cause radvd to deprecate the prefix by announcing it in the radvd
shutdown RA with a zero preferred lifetime and a valid lifetime slightly greater than 2 hours.
This will encourage end-nodes using this prefix to deprecate any associated addresses immediately.
Note that this option should only be used when only one router is announcing the prefix onto the
link, otherwise end-nodes will deprecate associated addresses despite the prefix still being valid
for preferred use.
See RFC4862, section 5.5.3., "Router Advertisement Processing", part (e).
Default: off
DecrementLifetimes on|off
This option causes radvd to decrement the values of the preferred and valid lifetimes for the
prefix over time. The lifetimes are decremented by the number of seconds since the last RA. If
radvd receives a SIGUSR1 signal, it will reset the values of the preferred and valid lifetimes
back to the initial values used by radvd when it started. If radvd never receives a SIGUSR1
signal, it will continue to decrement the lifetimes until the preferred lifetime reaches zero.
After a final RA with a zero value preferred lifetime, radvd will cease to announce the prefix. If
a SIGUSR1 signal then causes the lifetimes to be reset, the prefix will then re-appear in the RAs.
This option is intended to be used in conjunction with a DHCPv6 client that is using the Identity
Association for Prefix Delegation (IA_PD) option to acquire a prefix from a Delegating Router for
use by a Requesting Router. In this scenario, the prefix(es) from within the delegated prefix that
are announced by radvd would age in parallel with and at the same rate as the delegated prefix,
and expire at approximately the same time, if the delegated prefix's life isn't extended.
See RFC3633, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6".
Default: off
Base6Interface name
If this options is specified, this prefix will be combined with the IPv6 address of the interface
specified by name. The resulting prefix length will be 64.
Base6to4Interface name
If this option is specified, this prefix will be combined with the IPv4 address of interface name
to produce a valid 6to4 prefix. The first 16 bits of this prefix will be replaced by 2002 and the
next 32 bits of this prefix will be replaced by the IPv4 address assigned to interface name at
configuration time. The remaining 80 bits of the prefix (including the SLA ID) will be advertised
as specified in the configuration file. See the next section for an example.
If interface name is not available at configuration time, a warning will be written to the log and
this prefix will be disabled until radvd is reconfigured.
This option enables systems with dynamic IPv4 addresses to update their advertised 6to4 prefixes
simply by restarting radvd or sending a SIGHUP signal to cause radvd to reconfigure itself.
Note that 6to4 prefixes derived from dynamically-assigned IPv4 addresses should be advertised with
a significantly shorter lifetime (see the AdvValidLifetime and AdvPreferredLifetime options).
For more information on 6to4, see RFC 3056.
Default: 6to4 is not used
ROUTE SPECIFIC OPTIONS
AdvRouteLifetime seconds|infinity
The lifetime associated with the route in units of seconds. The symbolic value infinity
represents infinity (i.e. a value of all one bits (0xffffffff)).
Default: 3 * MaxRtrAdvInterval
AdvRoutePreference low|medium|high
The preference associated with the default router, as either "low", "medium", or "high".
Default: medium
RemoveRoute on|off
Upon shutdown, announce this route with a zero second lifetime. This should cause the route to be
immediately removed from the receiving end-nodes' route table.
Default: on
RDNSS SPECIFIC OPTIONS
AdvRDNSSLifetime seconds|infinity
The maximum duration how long the RDNSS entries are used for name resolution. A value of 0 means
the nameserver must no longer be used. The value, if not 0, must be at least MaxRtrAdvInterval.
To ensure stale RDNSS info gets removed in a timely fashion, this should not be greater than
2*MaxRtrAdvInterval.
Default: 2*MaxRtrAdvInterval
FlushRDNSS on|off
Upon shutdown, announce the RDNSS entries with a zero second lifetime. This should cause the RDNSS
addresses to be immediately removed from the end-nodes' list of Recursive DNS Servers.
Default: on
DNSSL SPECIFIC OPTIONS
AdvDNSSLLifetime seconds|infinity;
The maximum duration how long the DNSSL entries are used for name resolution. A value of 0 means
the suffix should no longer be used. The value, if not 0, must be at least MaxRtrAdvInterval. To
ensure stale DNSSL info gets removed in a timely fashion, this should not be greater than
2*MaxRtrAdvInterval.
Default: 2*MaxRtrAdvInterval
FlushDNSSL on|off
Upon shutdown, announce the DNSSL entries with a zero second lifetime. This should cause the DNSSL
entries to be immediately removed from the end-nodes' DNS search list.
Default: on
ABRO SPECIFIC OPTIONS
AdvValidLifeTime seconds
The time in units of that the set of border router information is valid. A value of all zero bits
assumes a default value of 10,000(~one week).
AdvVersionLow, AdvVersionHigh unsignedinteger
Both forms 32-bit unsigned version number corresponding to the set of information contained in RA
message.
EXAMPLES
interface eth0
{
AdvSendAdvert on;
prefix 2001:db8:0:1::/64
{
AdvOnLink on;
AdvAutonomous on;
};
};
It says that router advertisement daemon should advertise (AdvSendAdvert on;) the prefix 2001:db8:0:1::
which has a length of 64 on the interface eth0. Also the prefix should be marked as autonomous
(AdvAutonomous on;) and as on-link (AdvOnLink on;). All the other options are left on their default
values.
To support movement detection of Mobile IPv6 Mobile Nodes, the address of interface should be used
instead of network prefix:
interface eth0
{
AdvSendAdvert on;
prefix 2001:db8:0:1::4/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr on;
};
};
For 6to4 support, include the Base6to4Interface option in each prefix section. When using a dynamic IPv4
address, set small prefix lifetimes to prevent hosts from retaining unreachable prefixes after a new IPv4
address has been assigned. When advertising to on a dynamic interface (e.g., Bluetooth), skip the
interface if it is not active yet.
interface bnep0
{
IgnoreIfMissing on;
AdvSendAdvert on;
# Advertise at least every 30 seconds
MaxRtrAdvInterval 30;
prefix 0:0:0:5678::/64
{
AdvOnLink on;
AdvAutonomous on;
Base6to4Interface ppp0;
# Very short lifetimes for dynamic addresses
AdvValidLifetime 300;
AdvPreferredLifetime 120;
};
};
Since 6to4 is enabled, the prefix will be advertised as 2002:WWXX:YYZZ:5678::/64, where WW.XX.YY.ZZ is
the IPv4 address of ppp0 at configuration time. (IPv6 addresses are written in hexadecimal whereas IPv4
addresses are written in decimal, so the IPv4 address WW.XX.YY.ZZ in the 6to4 prefix will be represented
in hex.)
In this specific case, the configuration scripts may send HUP signal to radvd when taking bnep0 up or
down to notify about the status; in the current radvd releases, sending HUP is no longer mandatory when
the link comes back up.
interface eth0
{
AdvSendAdvert on;
prefix 2001:db8:0:1::/64
{
AdvOnLink on;
AdvAutonomous on;
};
clients
{
fe80::21f:16ff:fe06:3aab;
fe80::21d:72ff:fe96:aaff;
};
};
This configuration would only announce the prefix to fe80::21f:16ff:fe06:3aab and
fe80::21d:72ff:fe96:aaff. Furthermore, all RA requests of other clients are denied.
This may come in handy if you want to roll out IPv6 only partially because some clients are broken or
untested.
For ABRO support
interface lowpan0
{
AdvSendAdvert on;
UnicastOnly on;
AdvCurHopLimit 255;
prefix 2001:0db8:0100:f101::/64 {
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr on;
};
abro fe80::a200:0:0:1/64 {
AdvVersionLow 10;
AdvVersionHigh 2;
AdvValidLifeTime 2;
};
};
FILES
/usr/sbin/radvd
/etc/radvd.conf
/run/radvd.pid
/var/log/radvd.log
CREDIT
The description of the different flags and variables is in large parts taken from RFC 4861.
RFCS
Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP Version 6 (IPv6)", RFC
4861, September 2007.
Thomson, S., Narten, T., T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, September 2007.
Deering, S., and R. Hinden, "IP Version 6 Addressing Architecture", RFC 4291, February 2006.
Conta, A., Deering, S., and M. Gupta "Internet Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6)", RFC 4443, March 2006.
Crawford, M., "Transmission of IPv6 Packets over Ethernet Networks", RFC 2464, December 1998.
Carpenter B., K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. (6to4
specification)
Draves, R., D. Thaler, "Default Router Preferences and More-Specific Routes", RFC 4191, November 2005.
Johnson, D., Perkins, C., and J. Arkko, "Mobility Support in IPv6", RFC 3775, June 2004.
Devarapalli, V., Wakikawa, R., Petrescu, A., and P. Thubert "Network Mobility (NEMO) Basic Support
Protocol", RFC 3963, January 2005.
J. Jeong, S. Park, L. Beloeil, and S. Madanapalli, "IPv6 Router Advertisement Options for DNS
Configuration", RFC 6106, November 2010.
Z. Shelby, S. Chakrabarti, E. Nordmark and C. Bormann " Neighbor Discovery Optimization for IPv6 over
Low-Power Wireless Personal Area Networks (6LoWPANs)", RFC 6775, November 2012.
Gont, F. "Security Implications of IPv6 Fragmentation with IPv6 Neighbor Discovery", RFC 6980, August
2013.
Yourtchenko, A. and Colitti, L. "Reducing Energy Consumption of Router Advertisements", RFC 7772,
February 2016.
SEE ALSO
radvd(8), radvdump(8)
radvd 2.19 4 Jan 2011 RADVD.CONF(5)