Provided by: freeipmi-tools_1.6.13-3_amd64 
NAME
ipmi-sensors - display IPMI sensor information
SYNOPSIS
ipmi-sensors [OPTION...]
DESCRIPTION
Ipmi-sensors displays current readings of sensors and sensor data repository (SDR)
information. The default display outputs each sensor's record id, sensor name, sensor type
name, sensor reading (if appropriate), and the current sensor event. More verbose
information can be found using the verbose options specified below. Ipmi-sensors does not
inform the user if a problem exists with a particular sensor because sensor readings and
events are not analyzed by default. Users may wish to use the --output-sensor-state option
to output the analyzed sensor state. Some sensors may have a sensor reading or sensor
event of "N/A" if the information is unavailable. This is typical of a sensor that is not
enabled or not owned by a BMC. Please see --bridge-sensors option below to deal with
sensors not owned by a BMC. Sensors may output a sensor event of "Unknown" if the sensor
reading cannot be read. This is typical of a sensor that is busy or a reading that cannot
be calculated. If sensors report "Unrecognized State", it is indicative of an unknown
sensor type, typically an OEM sensor. If the sensor OEM interpretation is available, the
--interpret-oem-data may be able to report the appropriate sensor state. Sensors need not
always report a sensor event. When a sensor event is not present, "OK" is typically
reported.
Listed below are general IPMI options, tool specific options, trouble shooting
information, workaround information, examples, and known issues. For a general
introduction to FreeIPMI please see freeipmi(7). To perform IPMI sensor configuration,
please see ipmi-config(8). To perform some advanced SDR management, please see bmc-
device(8).
GENERAL OPTIONS
The following options are general options for configuring IPMI communication and executing
general tool commands.
-D IPMIDRIVER, --driver-type=IPMIDRIVER
Specify the driver type to use instead of doing an auto selection. The currently
available outofband drivers are LAN and LAN_2_0, which perform IPMI 1.5 and IPMI
2.0 respectively. The currently available inband drivers are KCS, SSIF, OPENIPMI,
SUNBMC, and INTELDCMI.
--disable-auto-probe
Do not probe in-band IPMI devices for default settings.
--driver-address=DRIVER-ADDRESS
Specify the in-band driver address to be used instead of the probed value. DRIVER-
ADDRESS should be prefixed with "0x" for a hex value and '0' for an octal value.
--driver-device=DEVICE
Specify the in-band driver device path to be used instead of the probed path.
--register-spacing=REGISTER-SPACING
Specify the in-band driver register spacing instead of the probed value. Argument
is in bytes (i.e. 32bit register spacing = 4)
--target-channel-number=CHANNEL-NUMBER
Specify the in-band driver target channel number to send IPMI requests to.
--target-slave-address=SLAVE-ADDRESS
Specify the in-band driver target slave number to send IPMI requests to.
-h IPMIHOST1,IPMIHOST2,..., --hostname=IPMIHOST1[:PORT],IPMIHOST2[:PORT],...
Specify the remote host(s) to communicate with. Multiple hostnames may be separated
by comma or may be specified in a range format; see HOSTRANGED SUPPORT below. An
optional port can be specified with each host, which may be useful in port
forwarding or similar situations. If specifying an IPv6 address and port, use the
format [ADDRESS]:PORT.
-u USERNAME, --username=USERNAME
Specify the username to use when authenticating with the remote host. If not
specified, a null (i.e. anonymous) username is assumed. The user must have atleast
OPERATOR privileges in order for this tool to operate fully.
-p PASSWORD, --password=PASSWORD
Specify the password to use when authenticationg with the remote host. If not
specified, a null password is assumed. Maximum password length is 16 for IPMI 1.5
and 20 for IPMI 2.0.
-P, --password-prompt
Prompt for password to avoid possibility of listing it in process lists.
-k K_G, --k-g=K_G
Specify the K_g BMC key to use when authenticating with the remote host for IPMI
2.0. If not specified, a null key is assumed. To input the key in hexadecimal form,
prefix the string with '0x'. E.g., the key 'abc' can be entered with the either the
string 'abc' or the string '0x616263'
-K, --k-g-prompt
Prompt for k-g to avoid possibility of listing it in process lists.
--session-timeout=MILLISECONDS
Specify the session timeout in milliseconds. Defaults to 20000 milliseconds (20
seconds) if not specified.
--retransmission-timeout=MILLISECONDS
Specify the packet retransmission timeout in milliseconds. Defaults to 1000
milliseconds (1 second) if not specified. The retransmission timeout cannot be
larger than the session timeout.
-a AUTHENTICATION-TYPE, --authentication-type=AUTHENTICATION-TYPE
Specify the IPMI 1.5 authentication type to use. The currently available
authentication types are NONE, STRAIGHT_PASSWORD_KEY, MD2, and MD5. Defaults to MD5
if not specified.
-I CIPHER-SUITE-ID, --cipher-suite-id=CIPHER-SUITE-ID
Specify the IPMI 2.0 cipher suite ID to use. The Cipher Suite ID identifies a set
of authentication, integrity, and confidentiality algorithms to use for IPMI 2.0
communication. The authentication algorithm identifies the algorithm to use for
session setup, the integrity algorithm identifies the algorithm to use for session
packet signatures, and the confidentiality algorithm identifies the algorithm to
use for payload encryption. Defaults to cipher suite ID 3 if not specified. The
following cipher suite ids are currently supported:
0 - Authentication Algorithm = None; Integrity Algorithm = None; Confidentiality
Algorithm = None
1 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = None;
Confidentiality Algorithm = None
2 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96;
Confidentiality Algorithm = None
3 - Authentication Algorithm = HMAC-SHA1; Integrity Algorithm = HMAC-SHA1-96;
Confidentiality Algorithm = AES-CBC-128
6 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = None;
Confidentiality Algorithm = None
7 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128;
Confidentiality Algorithm = None
8 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = HMAC-MD5-128;
Confidentiality Algorithm = AES-CBC-128
11 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = MD5-128;
Confidentiality Algorithm = None
12 - Authentication Algorithm = HMAC-MD5; Integrity Algorithm = MD5-128;
Confidentiality Algorithm = AES-CBC-128
15 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm = None;
Confidentiality Algorithm = None
16 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm = HMAC_SHA256_128;
Confidentiality Algorithm = None
17 - Authentication Algorithm = HMAC-SHA256; Integrity Algorithm = HMAC_SHA256_128;
Confidentiality Algorithm = AES-CBC-128
-l PRIVILEGE-LEVEL, --privilege-level=PRIVILEGE-LEVEL
Specify the privilege level to be used. The currently available privilege levels
are USER, OPERATOR, and ADMIN. Defaults to OPERATOR if not specified.
--config-file=FILE
Specify an alternate configuration file.
-W WORKAROUNDS, --workaround-flags=WORKAROUNDS
Specify workarounds to vendor compliance issues. Multiple workarounds can be
specified separated by commas. A special command line flag of "none", will indicate
no workarounds (may be useful for overriding configured defaults). See WORKAROUNDS
below for a list of available workarounds.
--debug
Turn on debugging.
-?, --help
Output a help list and exit.
--usage
Output a usage message and exit.
-V, --version
Output the program version and exit.
IPMI-SENSORS OPTIONS
The following options are specific to ipmi-sensors.
-v, --verbose
Output verbose sensor output. This option will output additional information about
sensors such as thresholds, ranges, numbers, and event/reading type codes.
-vv Output very verbose sensor output. This option will output more additional
information than the verbose option such as information about events, other sensor
types, and oem sensors.
-i, --sdr-info
Show sensor data repository (SDR) information
-q, --quiet-readings
Do not output sensor reading values by default. This option is particularly useful
if you want to use hostranged output across a cluster and want to consolidate the
output.
-r RECORD-IDS-LIST, --record-ids=RECORD-IDS-LIST
Specify sensors to show by record id. Multiple record ids can be separated by
commas or spaces. If both --record-ids and --sensor-types are specified,
--record-ids takes precedence. A special command line record id of "all", will
indicate all record ids should be shown (may be useful for overriding configured
defaults).
-R RECORD-IDS-LIST, --exclude-record-ids=RECORD-IDS-LIST
Specify sensors to not show by record id. Multiple record ids can be separated by
commas or spaces. A special command line record id of "none", will indicate no
record ids should be excluded (may be useful for overriding configured defaults).
-t SENSOR-TYPE-LIST, --sensor-types=SENSOR-TYPE-LIST
Specify sensor types to show outputs for. Multiple types can be separated by commas
or spaces. If both --record-ids and --sensor-types are specified, --record-ids
takes precedence. A special command line type of "all", will indicate all types
should be shown (may be useful for overriding configured defaults). Users may
specify sensor types by string (see --list-sensor-types below) or by number
(decimal or hex).
-T SENSOR-TYPE-LIST, --exclude-sensor-types=SENSOR-TYPE-LIST
Specify sensor types to not show outputs for. Multiple types can be eparated by
commas or spaces. A special command line type of "none", will indicate no types
should be excluded (may be useful for overriding configured defaults). Users may
specify sensor types by string (see --list-sensor-types below) or by number
(decimal or hex).
-L, --list-sensor-types
List sensor types.
-b, --bridge-sensors
By default, sensors readings are not attempted for sensors on non-BMC owners. By
setting this option, sensor requests can be bridged to non-BMC owners to obtain
sensor readings. Bridging may not work on some interfaces/driver types.
--shared-sensors
Some sensors share the same sensor data record (SDR). This is typically utilized
for system event log (SEL) entries and not for sensor readings. However, there may
be some motherboards in which this format is utilized for multiple active sensors,
or the user simply has interest in seeing the permutation of entries shared by a
SDR entry. By setting this option, each sensor number shared by a record will be
iterated over and output.
--interpret-oem-data
Attempt to interpret OEM data, such as event data, sensor readings, or general
extra info, etc. If an OEM interpretation is not available, the default output will
be generated. Correctness of OEM interpretations cannot be guaranteed due to
potential changes OEM vendors may make in products, firmware, etc. See OEM
INTERPRETATION below for confirmed supported motherboard interpretations.
--ignore-not-available-sensors
Ignore not-available (i.e. N/A) sensors in output.
--ignore-unrecognized-events
Ignore unrecognized sensor events. This will suppress output of unrecognized
events, typically shown as 'Unrecognized Event = XXXXh' in output. In addition,
unrecognized events will be ignored when calculating sensor state with
--output-sensor-state below.
--output-event-bitmask
Output event bitmask value instead of the string representation.
--output-sensor-state
Output sensor state in output. This will add an additional output reporting if a
sensor is in a NOMINAL, WARNING, or CRITICAL state. The sensor state is an
interpreted value based on the current sensor event. The sensor state
interpretations are determined by the configuration file
/etc/freeipmi//freeipmi_interpret_sensor.conf. See
freeipmi_interpret_sensor.conf(5) for more information. This option gives
identical output to the sensor state previously output by ipmimonitoring(8).
--sensor-state-config-file=FILE
Specify an alternate sensor state configuration file. Option ignored if
--output-sensor-state not specified.
--entity-sensor-names
Output sensor names prefixed with their entity id and instance number when
appropriate. This may be necessary on some motherboards to help identify what
sensors are referencing. For example, a motherboard may have multiple sensors named
'TEMP'. The entity id and instance number may help clarify which sensor refers to
"Processor 1" vs. "Processor 2".
--output-sensor-thresholds
Output sensor thresholds in output. This will add columns to the default output for
lower non-recoverable, lower critical, lower non-critical, upper non-critical,
upper critical, and upper non-recoverable thresholds.
--no-sensor-type-output
Do not show sensor type output for each entry. On many systems, the sensor type is
redundant to the name of the sensor. This can especially be true if
--entity-sensor-names is specified. If the sensor name is sufficient, or if the
sensor type is of no interest to the user, this option can be specified to condense
output.
--comma-separated-output
Output fields in comma separated format.
--no-header-output
Do not output column headers. May be useful in scripting.
--non-abbreviated-units
Output non-abbreviated units (e.g. 'Amps' instead of 'A'). May aid in
disambiguation of units (e.g. 'C' for Celsius or Coulombs).
--legacy-output
Output in legacy format. Newer options may not be applicable to legacy output.
--ipmimonitoring-legacy-output
Output legacy format of legacy ipmimonitoring tool. Newer options may not be
applicable to legacy output.
SDR CACHE OPTIONS
This tool requires access to the sensor data repository (SDR) cache for general operation.
By default, SDR data will be downloaded and cached on the local machine. The following
options apply to the SDR cache.
--flush-cache
Flush a cached version of the sensor data repository (SDR) cache. The SDR is
typically cached for faster subsequent access. However, it may need to be flushed
and re-generated if the SDR has been updated on a system.
--quiet-cache
Do not output information about cache creation/deletion. May be useful in
scripting.
--sdr-cache-recreate
If the SDR cache is out of date or invalid, automatically recreate the sensor data
repository (SDR) cache. This option may be useful for scripting purposes.
--sdr-cache-file=FILE
Specify a specific sensor data repository (SDR) cache file to be stored or read
from. If this option is used when multiple hosts are specified, the same SDR cache
file will be used for all hosts.
--sdr-cache-directory=DIRECTORY
Specify an alternate directory for sensor data repository (SDR) caches to be stored
or read from. Defaults to the home directory if not specified.
TIME OPTIONS
By IPMI definition, all IPMI times and timestamps are stored in localtime. However, in
many situations, the timestamps will not be stored in localtime. Whether or not a system
truly stored the timestamps in localtime varies on many factors, such as the vendor, BIOS,
and operating system. The following options will allow the user to adjust the
interpretation of the stored timestamps and how they should be output.
--utc-to-localtime
Assume all times are reported in UTC time and convert the time to localtime before
being output.
--localtime-to-utc
Convert all localtime timestamps to UTC before being output.
--utc-offset=SECONDS
Specify a specific UTC offset in seconds to be added to timestamps. Value can
range from -86400 to 86400 seconds. Defaults to 0.
HOSTRANGED OPTIONS
The following options manipulate hostranged output. See HOSTRANGED SUPPORT below for
additional information on hostranges.
-B, --buffer-output
Buffer hostranged output. For each node, buffer standard output until the node has
completed its IPMI operation. When specifying this option, data may appear to
output slower to the user since the the entire IPMI operation must complete before
any data can be output. See HOSTRANGED SUPPORT below for additional information.
-C, --consolidate-output
Consolidate hostranged output. The complete standard output from every node
specified will be consolidated so that nodes with identical output are not output
twice. A header will list those nodes with the consolidated output. When this
option is specified, no output can be seen until the IPMI operations to all nodes
has completed. If the user breaks out of the program early, all currently
consolidated output will be dumped. See HOSTRANGED SUPPORT below for additional
information.
-F NUM, --fanout=NUM
Specify multiple host fanout. A "sliding window" (or fanout) algorithm is used for
parallel IPMI communication so that slower nodes or timed out nodes will not impede
parallel communication. The maximum number of threads available at the same time is
limited by the fanout. The default is 64.
-E, --eliminate
Eliminate hosts determined as undetected by ipmidetect. This attempts to remove
the common issue of hostranged execution timing out due to several nodes being
removed from service in a large cluster. The ipmidetectd daemon must be running on
the node executing the command.
--always-prefix
Always prefix output, even if only one host is specified or communicating in-band.
This option is primarily useful for scripting purposes. Option will be ignored if
specified with the -C option.
HOSTRANGED SUPPORT
Multiple hosts can be input either as an explicit comma separated lists of hosts or a
range of hostnames in the general form: prefix[n-m,l-k,...], where n < m and l < k, etc.
The later form should not be confused with regular expression character classes (also
denoted by []). For example, foo[19] does not represent foo1 or foo9, but rather
represents a degenerate range: foo19.
This range syntax is meant only as a convenience on clusters with a prefixNN naming
convention and specification of ranges should not be considered necessary -- the list
foo1,foo9 could be specified as such, or by the range foo[1,9].
Some examples of range usage follow:
foo[01-05] instead of foo01,foo02,foo03,foo04,foo05
foo[7,9-10] instead of foo7,foo9,foo10
foo[0-3] instead of foo0,foo1,foo2,foo3
As a reminder to the reader, some shells will interpret brackets ([ and ]) for pattern
matching. Depending on your shell, it may be necessary to enclose ranged lists within
quotes.
When multiple hosts are specified by the user, a thread will be executed for each host in
parallel up to the configured fanout (which can be adjusted via the -F option). This will
allow communication to large numbers of nodes far more quickly than if done in serial.
By default, standard output from each node specified will be output with the hostname
prepended to each line. Although this output is readable in many situations, it may be
difficult to read in other situations. For example, output from multiple nodes may be
mixed together. The -B and -C options can be used to change this default.
In-band IPMI Communication will be used when the host "localhost" is specified. This
allows the user to add the localhost into the hostranged output.
GENERAL TROUBLESHOOTING
Most often, IPMI problems are due to configuration problems.
IPMI over LAN problems involve a misconfiguration of the remote machine's BMC. Double
check to make sure the following are configured properly in the remote machine's BMC: IP
address, MAC address, subnet mask, username, user enablement, user privilege, password,
LAN privilege, LAN enablement, and allowed authentication type(s). For IPMI 2.0
connections, double check to make sure the cipher suite privilege(s) and K_g key are
configured properly. The ipmi-config(8) tool can be used to check and/or change these
configuration settings.
Inband IPMI problems are typically caused by improperly configured drivers or non-standard
BMCs.
In addition to the troubleshooting tips below, please see WORKAROUNDS below to also if
there are any vendor specific bugs that have been discovered and worked around.
Listed below are many of the common issues for error messages. For additional support,
please e-mail the <freeipmi-users@gnu.org> mailing list.
"username invalid" - The username entered (or a NULL username if none was entered) is not
available on the remote machine. It may also be possible the remote BMC's username
configuration is incorrect.
"password invalid" - The password entered (or a NULL password if none was entered) is not
correct. It may also be possible the password for the user is not correctly configured on
the remote BMC.
"password verification timeout" - Password verification has timed out. A "password
invalid" error (described above) or a generic "session timeout" (described below)
occurred. During this point in the protocol it cannot be differentiated which occurred.
"k_g invalid" - The K_g key entered (or a NULL K_g key if none was entered) is not
correct. It may also be possible the K_g key is not correctly configured on the remote
BMC.
"privilege level insufficient" - An IPMI command requires a higher user privilege than the
one authenticated with. Please try to authenticate with a higher privilege. This may
require authenticating to a different user which has a higher maximum privilege.
"privilege level cannot be obtained for this user" - The privilege level you are
attempting to authenticate with is higher than the maximum allowed for this user. Please
try again with a lower privilege. It may also be possible the maximum privilege level
allowed for a user is not configured properly on the remote BMC.
"authentication type unavailable for attempted privilege level" - The authentication type
you wish to authenticate with is not available for this privilege level. Please try again
with an alternate authentication type or alternate privilege level. It may also be
possible the available authentication types you can authenticate with are not correctly
configured on the remote BMC.
"cipher suite id unavailable" - The cipher suite id you wish to authenticate with is not
available on the remote BMC. Please try again with an alternate cipher suite id. It may
also be possible the available cipher suite ids are not correctly configured on the remote
BMC.
"ipmi 2.0 unavailable" - IPMI 2.0 was not discovered on the remote machine. Please try to
use IPMI 1.5 instead.
"connection timeout" - Initial IPMI communication failed. A number of potential errors are
possible, including an invalid hostname specified, an IPMI IP address cannot be resolved,
IPMI is not enabled on the remote server, the network connection is bad, etc. Please
verify configuration and connectivity.
"session timeout" - The IPMI session has timed out. Please reconnect. If this error
occurs often, you may wish to increase the retransmission timeout. Some remote BMCs are
considerably slower than others.
"device not found" - The specified device could not be found. Please check configuration
or inputs and try again.
"driver timeout" - Communication with the driver or device has timed out. Please try
again.
"message timeout" - Communication with the driver or device has timed out. Please try
again.
"BMC busy" - The BMC is currently busy. It may be processing information or have too many
simultaneous sessions to manage. Please wait and try again.
"could not find inband device" - An inband device could not be found. Please check
configuration or specify specific device or driver on the command line.
"driver timeout" - The inband driver has timed out communicating to the local BMC or
service processor. The BMC or service processor may be busy or (worst case) possibly non-
functioning.
"internal IPMI error" - An IPMI error has occurred that FreeIPMI does not know how to
handle. Please e-mail <freeipmi-users@gnu.org> to report the issue.
"sensor config file parse error" - A parse error was found in the sensor interpretation
configuration file. Please see freeipmi_interpret_sensor.conf(5).
WORKAROUNDS
With so many different vendors implementing their own IPMI solutions, different vendors
may implement their IPMI protocols incorrectly. The following describes a number of
workarounds currently available to handle discovered compliance issues. When possible,
workarounds have been implemented so they will be transparent to the user. However, some
will require the user to specify a workaround be used via the -W option.
The hardware listed below may only indicate the hardware that a problem was discovered on.
Newer versions of hardware may fix the problems indicated below. Similar machines from
vendors may or may not exhibit the same problems. Different vendors may license their
firmware from the same IPMI firmware developer, so it may be worthwhile to try workarounds
listed below even if your motherboard is not listed.
If you believe your hardware has an additional compliance issue that needs a workaround to
be implemented, please contact the FreeIPMI maintainers on <freeipmi-users@gnu.org> or
<freeipmi-devel@gnu.org>.
assumeio - This workaround flag will assume inband interfaces communicate with system I/O
rather than being memory-mapped. This will work around systems that report invalid base
addresses. Those hitting this issue may see "device not supported" or "could not find
inband device" errors. Issue observed on HP ProLiant DL145 G1.
spinpoll - This workaround flag will inform some inband drivers (most notably the KCS
driver) to spin while polling rather than putting the process to sleep. This may
significantly improve the wall clock running time of tools because an operating system
scheduler's granularity may be much larger than the time it takes to perform a single IPMI
message transaction. However, by spinning, your system may be performing less useful work
by not contexting out the tool for a more useful task.
authcap - This workaround flag will skip early checks for username capabilities,
authentication capabilities, and K_g support and allow IPMI authentication to succeed. It
works around multiple issues in which the remote system does not properly report username
capabilities, authentication capabilities, or K_g status. Those hitting this issue may see
"username invalid", "authentication type unavailable for attempted privilege level", or
"k_g invalid" errors. Issue observed on Asus P5M2/P5MT-R/RS162-E4/RX4, Intel
SR1520ML/X38ML, and Sun Fire 2200/4150/4450 with ELOM.
nochecksumcheck - This workaround flag will tell FreeIPMI to not check the checksums
returned from IPMI command responses. It works around systems that return invalid
checksums due to implementation errors, but the packet is otherwise valid. Users are
cautioned on the use of this option, as it removes validation of packet integrity in a
number of circumstances. However, it is unlikely to be an issue in most situations. Those
hitting this issue may see "connection timeout", "session timeout", or "password
verification timeout" errors. On IPMI 1.5 connections, the "noauthcodecheck" workaround
may also needed too. Issue observed on Supermicro X9SCM-iiF, Supermicro X9DRi-F, and
Supermicro X9DRFR.
idzero - This workaround flag will allow empty session IDs to be accepted by the client.
It works around IPMI sessions that report empty session IDs to the client. Those hitting
this issue may see "session timeout" errors. Issue observed on Tyan S2882 with M3289 BMC.
unexpectedauth - This workaround flag will allow unexpected non-null authcodes to be
checked as though they were expected. It works around an issue when packets contain non-
null authentication data when they should be null due to disabled per-message
authentication. Those hitting this issue may see "session timeout" errors. Issue observed
on Dell PowerEdge 2850,SC1425. Confirmed fixed on newer firmware.
forcepermsg - This workaround flag will force per-message authentication to be used no
matter what is advertised by the remote system. It works around an issue when per-message
authentication is advertised as disabled on the remote system, but it is actually required
for the protocol. Those hitting this issue may see "session timeout" errors. Issue
observed on IBM eServer 325.
endianseq - This workaround flag will flip the endian of the session sequence numbers to
allow the session to continue properly. It works around IPMI 1.5 session sequence numbers
that are the wrong endian. Those hitting this issue may see "session timeout" errors.
Issue observed on some Sun ILOM 1.0/2.0 (depends on service processor endian).
noauthcodecheck - This workaround flag will tell FreeIPMI to not check the authentication
codes returned from IPMI 1.5 command responses. It works around systems that return
invalid authentication codes due to hashing or implementation errors. Users are cautioned
on the use of this option, as it removes an authentication check verifying the validity of
a packet. However, in most organizations, this is unlikely to be a security issue. Those
hitting this issue may see "connection timeout", "session timeout", or "password
verification timeout" errors. Issue observed on Xyratex FB-H8-SRAY, Intel Windmill,
Quanta Winterfell, and Wiwynn Windmill.
intel20 - This workaround flag will work around several Intel IPMI 2.0 authentication
issues. The issues covered include padding of usernames, and password truncation if the
authentication algorithm is HMAC-MD5-128. Those hitting this issue may see "username
invalid", "password invalid", or "k_g invalid" errors. Issue observed on Intel SE7520AF2
with Intel Server Management Module (Professional Edition).
supermicro20 - This workaround flag will work around several Supermicro IPMI 2.0
authentication issues on motherboards w/ Peppercon IPMI firmware. The issues covered
include handling invalid length authentication codes. Those hitting this issue may see
"password invalid" errors. Issue observed on Supermicro H8QME with SIMSO daughter card.
Confirmed fixed on newerver firmware.
sun20 - This workaround flag will work work around several Sun IPMI 2.0 authentication
issues. The issues covered include invalid lengthed hash keys, improperly hashed keys, and
invalid cipher suite records. Those hitting this issue may see "password invalid" or "bmc
error" errors. Issue observed on Sun Fire 4100/4200/4500 with ILOM. This workaround
automatically includes the "opensesspriv" workaround.
opensesspriv - This workaround flag will slightly alter FreeIPMI's IPMI 2.0 connection
protocol to workaround an invalid hashing algorithm used by the remote system. The
privilege level sent during the Open Session stage of an IPMI 2.0 connection is used for
hashing keys instead of the privilege level sent during the RAKP1 connection stage. Those
hitting this issue may see "password invalid", "k_g invalid", or "bad rmcpplus status
code" errors. Issue observed on Sun Fire 4100/4200/4500 with ILOM, Inventec 5441/Dell
Xanadu II, Supermicro X8DTH, Supermicro X8DTG, Intel S5500WBV/Penguin Relion 700, Intel
S2600JF/Appro 512X, Quanta QSSC-S4R/Appro GB812X-CN, and Dell C5220. This workaround is
automatically triggered with the "sun20" workaround.
integritycheckvalue - This workaround flag will work around an invalid integrity check
value during an IPMI 2.0 session establishment when using Cipher Suite ID 0. The integrity
check value should be 0 length, however the remote motherboard responds with a non-empty
field. Those hitting this issue may see "k_g invalid" errors. Issue observed on Supermicro
X8DTG, Supermicro X8DTU, and Intel S5500WBV/Penguin Relion 700, and Intel S2600JF/Appro
512X.
assumemaxsdrrecordcount - This workaround will inform SDR reading to stop reading after a
known maximum number of SDR records have been read. This will work around systems that
have miss-implemented SDR reading functions. Those hitting this issue may see "SDR record
count invalid" errors. Issue observed on unspecified Inspur motherboard.
discretereading - This workaround option will allow analog sensor readings (i.e. rpm,
degrees, etc.) to be read even if the event/reading type code for the sensor is for a
discrete sensor (i.e. assert vs. deassert). This option works around poorly defined (and
arguably illegal) SDR records that expect analog sensor readings to be read alongside
discrete sensors. This option is confirmed to work around issues on HP Proliant DL380 G7
and HP ProLiant ML310 G5 motherboards.
ignorescanningdisabled - This workaround option will allow sensor readings to be read even
if the sensor scanning bit indicates a sensor is disabled. This option works around
motherboards that incorrectly indicate sensors as disabled. This may problem may exist on
your motherboard if sensors are listed as "N/A" even if they should be available. This
option is confirmed to work around issues on Dell Poweredge 2900, Dell Poweredge 2950,
Dell Poweredge R410, Dell Poweredge R610, and HP Integrity rx3600 motherboards.
assumebmcowner - This workaround option will allow sensor readings to be read if the
sensor owner is the BMC, but the reported sensor owner is not the BMC. Typically, sensors
owned by a non-BMC sensor owner must be bridged (e.g. with the --bridge-sensors option),
however if the non-BMC sensor owner is invalid, bridging fails. This option works around
motherboards that incorrectly report an non-BMC sensor owner by always assuming the sensor
owner is the BMC. This problem may exist on your motherboard if sensors are listed as
"N/A" even if they should be available. This option is confirmed to work around issues on
Fujitsu RX300 and Fujitsu RX300S2 motherboards.
ignoreauthcode - This workaround option will allow sensor readings to be read if the
remote machine is invalidly calculating authentication codes (i.e. authentication hashes)
when communicating over LAN. This problem may exist on your system if the error "session
timeout" errors or there is an appearance of a hang. Users are cautioned on the use of
this option, as it removes an authentication check verifying the validity of a packet.
However, in most organizations, this is unlikely to be a security issue. The ignoring of
authentication packets is only limited to the period in which sensor readings are done,
and not for any portion of the session authentication or session teardown. This option is
confirmed to work on Inventec 5441/Dell Xanadu II and Inventec 5442/Dell Xanadu III.
(Note: On the above systems, this issue has only been observed when the --bridge-sensors
is used.)
No IPMI 1.5 Support - Some motherboards that support IPMI 2.0 have been found to not
support IPMI 1.5. Those hitting this issue may see "ipmi 2.0 unavailable" or "connection
timeout" errors. This issue can be worked around by using IPMI 2.0 instead of IPMI 1.5 by
specifying --driver-type=LAN_2_0. Issue observed on a number of HP and Supermicro
motherboards.
OEM INTERPRETATION
The following motherboards are confirmed to have atleast some support by the --interpret-
oem-data option. While highly probable the OEM data interpretations would work across
other motherboards by the same manufacturer, there are no guarantees. Some of the
motherboards below may be rebranded by vendors/distributors.
Dell Poweredge R210, Dell Poweredge R610, Dell Poweredge R710, Dell Poweredge R720,
Fujitsu iRMC S1 and iRMC S2 systems, HP Proliant DL160 G8, Intel S5500WB/Penguin Computing
Relion 700, Intel S2600JF/Appro 512X, Intel S2600GZ, Intel S2600WP, Intel S5000PAL, Intel
Windmill, Quanta Winterfell, Supermicro X7DBR-3, Supermicro X7DB8, Supermicro X8DTN,
Supermicro X7SBI-LN4, Supermicro X8DTH, Supermicro X8DTG, Supermicro X8DTU, Supermicro
X8DT3-LN4F, Supermicro X8DTU-6+, Supermicro X8DTL, Supermicro X8DTL-3F, Supermicro X8SIL-
F, Supermicro X9SCL, Supermicro X9SCM, Supermicro X8DTN+-F, Supermicro X8SIE, Supermicro
X9SCA-F-O, Supermicro H8DGU-F, Supermicro X9DRi-F, Supermicro X9DRI-LN4F+, Supermicro
X9SPU-F-O, Supermicro X9SCM-iiF, Wiwynn Windmill, Wistron/Dell Poweredge C6220.
EXAMPLES
# ipmi-sensors
Show all sensors and readings on the local machine.
# ipmi-sensors --verbose
Show verbose sensors and readings on the local machine.
# ipmi-sensors --record-ids="7,11,102"
Show sensor record ids 7, 11, and 102 on the local machine.
# ipmi-sensors --sensor-types=fan
Show all sensors of type fan on the local machine.
# ipmi-sensors -h ahost -u myusername -p mypassword
Show all sensors on a remote machine using IPMI over LAN.
# ipmi-sensors -h mycluster[0-127] -u myusername -p mypassword
Show all sensors across a cluster using IPMI over LAN.
DIAGNOSTICS
Upon successful execution, exit status is 0. On error, exit status is 1.
If multiple hosts are specified for communication, the exit status is 0 if and only if all
targets successfully execute. Otherwise the exit status is 1.
KNOWN ISSUES
On older operating systems, if you input your username, password, and other potentially
security relevant information on the command line, this information may be discovered by
other users when using tools like the ps(1) command or looking in the /proc file system.
It is generally more secure to input password information with options like the -P or -K
options. Configuring security relevant information in the FreeIPMI configuration file
would also be an appropriate way to hide this information.
In order to prevent brute force attacks, some BMCs will temporarily "lock up" after a
number of remote authentication errors. You may need to wait awhile in order to this
temporary "lock up" to pass before you may authenticate again.
Some sensors may be output as not available (i.e. N/A) because the owner of the sensor is
not the BMC. To attempt to bridge sensors and access sensors not on the BMC, users may
wish to try the -b or --bridge-sensors options.
REPORTING BUGS
Report bugs to <freeipmi-users@gnu.org> or <freeipmi-devel@gnu.org>.
COPYRIGHT
Copyright © 2003-2015 FreeIPMI Core Team.
This program is free software; you can redistribute it and/or modify it under the terms of
the GNU General Public License as published by the Free Software Foundation; either
version 3 of the License, or (at your option) any later version.
SEE ALSO
freeipmi(7), bmc-device(8), ipmi-config(8), freeipmi_interpret_sensor.conf(5)
http://www.gnu.org/software/freeipmi/