Provided by: ser2net_4.6.0-1build2_amd64 
NAME
ser2net - Serial to network proxy
SYNOPSIS
ser2net [-c configfile] [-C configline] [-p controlport] [-n] [-d] [-b] [-v] [-P pidfile]
DESCRIPTION
The ser2net daemon allows telnet and tcp sessions to be established with a unit's serial ports or with an
IPMI Serial Over LAN (SOL) interface.
The program comes up normally as a daemon, opens the network ports specified in the configuration file,
and waits for connections. Once a connection occurs, the program attempts to set up the connection and
open the serial port. If another user is already using the connection or serial port, the connection is
refused with an error message.
OPTIONS
-c config-file
Set the configuration file to one other than the default of sysconfdir/ser2net/ser2net.yaml. If
the config-file is - then standard input is read as the config file. See -C for info on
sysconfdir
-C sysconfdir
Set the directory where the configuration file and ssl keys are stored. This is generally
/etc/ser2net on Unix-type systems, on Windows it is ../etc/ser2net from the executable's location
by default.
-a authdir
Set the default directory where authentication information is stored. This is generally
/usr/share/ser2net on Unix-type systems, on Windows it is ../share/ser2net from the executable's
location by default. This can be overridden in the config file. See the ser2net.yaml.5 for info
on what this does.
-A admin-authdir
Set the default directory where the administrator's authentication information is stores. This is
sysconfdir/auth by default. This can be overridden in the config file. See the ser2net.yaml.5
for info on what this does.
-Y yaml-config-string
Add a yaml config string to the end of strings to be processed. This may be specified multiple
times for multiple strings. These are appended onto the end of a yaml config file; though if this
is specified, the default config file is disabled and you have to enable it with the -c option.
To make things easier to handle, any # in the config string that is not inside quotes (what would
normally start a comment in yaml) is converted to a new line. Plus a new line is added after each
separate config string. So, for instance:
-Y 'connection: &con01# accepter: tcp,2013'
-Y ' connector: serialdev,/dev/ttyEcho0,9600n81,local'
-Y ' options:# banner: "### A Banner ###\r\n"'
can be put on the ser2net command line.
-n Stops the daemon from forking and detaching from the controlling terminal. This is useful
for running from init.
-d Like -n, but also sends the system logs to standard output. This is most useful for debugging
purposes.
-P pidfile
If specified, put the process id (pid) of ser2net in the pidfile, replacing whatever was in that
file previously. A pidfile is not created by default, you must specify this to create one. Note
also that this filename must be specific with the full path, as ser2net will change directory to
"/" when it becomes a daemon.
-u If UUCP locking is enabled, this will disable the use of UUCP locks.
-b Cisco IOS uses a different mechanism for specifying the baud rates than the mechanism described in
RFC2217. This option sets the IOS version of setting the baud rates. The default is RFC2217's.
Note that this capability is now handled automatically and this option is ignored.
-v Prints the version of the program and exits.
-t <num threads>
Spawn the given number of threads for ser2net to use. The default is 1. Only valid if pthreads
is enabled at build time.
-p <admin-accepter>
Enables the admin interface on the given accepter specification. See "ADMIN CONNECTION" in
ser2net.yaml(5) for more details on how to configure this, and "ADMIN INTERFACE" below for details
on how to use it.
-s signature
Specifies the default RFC2217 signature.
ADMIN INTERFACE
The admin interface provides a simple interface for controlling the ports and viewing their status. To
accomplish this, it has the following commands:
showport [<network port>]
Show information about a port. If no port is given, all ports are displayed.
showshortport [<network port>]
Show information about a port, each port on one line. If no port is given, all ports are
displayed. This can produce very wide output.
help Display a short list and summary of commands.
exit Disconnect from the control port.
yaml Go into yaml output mode. See YAML MODES below.
version
Display the version of this program.
monitor <type> <network port>
Display all the input for a given port on the calling control port. Only one direction may be
monitored at a time. The type field may be tcp or term and specifies whether to monitor data from
the network port or from the serial port Note that data monitoring is best effort, if the
controller port cannot keep up the data will be silently dropped. A controller may only monitor
one thing and a port may only be monitored by one controller.
monitor stop
Stop the current monitor.
disconnect <network port>
Disconnect the tcp connection on the port.
setporttimeout <network port> <timeout>
Set the amount of time in seconds before the port connection will be shut down if no activity has
been seen on the port.
setportconfig <network port> <config>
Set the port configuration as in the device configuration in the /etc/ser2net/ser2net.yaml file.
If conflicting options are specified, the last option will be the one used. Note that these will
not change until the port is disconnected and connected again. Options 300, 1200, 2400, 4800,
9600, 19200, 38400, 57600, 115200 set the various baud rates. The following speed may be
available if your system has the values defined and your hardware supports it: 230400, 460800,
500000, 576000, 921600, 1000000, 1152000, 1500000, 2000000, 2500000, 3000000, 3500000, 4000000.
Parity, databits, and stopbits may be specified in the classical manner after the speed, as in
9600N81. This has the following format: <speed>[N|E|O|M|S[5|6|7|8[1|2]]]. Setting serial options
this way does not work on SOL, SOL has fixed N81 serial options. EVEN, ODD, NONE (MARK and SPACE
if supported) set the parity. 1STOPBIT, 2STOPBITS set the number of stop bits. 7DATABITS,
8DATABITS set the number of data bits. [-]XONXOFF turns on (- off) XON/XOFF support. [-]RTSCTS
turns on (- off) hardware flow control. [-]LOCAL ignores (- checks) the modem control lines (DCD,
DTR, etc.)
setportcontrol <network port> <controls>
Modify dynamic port controls. These do not stay between connections. Controls are: DTRHI, DTRLO
Turns on and off the DTR line. RTSHI, RTSLO Turns on and off the RTS line.
setportenable <network port> <enable state>
Sets the port operation state. Valid states are: off to shut the network port down, raw to enable
the network port transfer all I/O as-is, rawlp to enable the network port input and device output
without termios setting, and telnet to enable the network port is up run the telnet negotiation
protocol on the port.
reload Causes ser2net to reload its configuration. Any error output will come out in the output, along
with going to syslog.
YAML MODES
If the "yaml" command is issued, echo is turned off and all output is YAML compliant. The form is
basically the same as the non-YAML output, with some minor adjustments to make it YAML compliant. In
addition, all responses are in the form:
%YAML 1.1
---
response:
<response info here>
...
If there is an error, it is returned in the response with the "error" key. If the command succeeded, no
"error" key will be present in the response mapping. The "..." will be at the end of all responses.
The following commands are available in yaml output mode: exit, version, showport, disconnect,
setporttimeout, setportenable, setportcontrol, reload,
If "%YAML" is seen in the input, YAML input and output modes are activated, echo is disabled, and all
input is expected to be in the form:
---
command:
name: <command name>
id: <optional id>
parms: [ parm1 [, parm2 [...]]]
...
The id is optional and will just be returned in the response. The parms are optional, too, unless the
command requires them. Extra parms are ignored, along with unknown keys in the main mapping.
Note that you have to deal with the "->" that is issued when the connection is made, before going into
YAML mode, YAML doesn't handle that well.
In YAML output mode, you will get asynchronous reports of connections and disconnections in the form:
%YAML 1.1
---
new connection:
name: !!str 'con1'
remaddr: !!str 'ipv6,::1,59072'
...
%YAML 1.1
---
disconnect:
name: !!str 'con1'
remaddr: !!str 'ipv6,::1,59072'
...
CONFIGURATION
Configuration is accomplished through the file /etc/ser2net/ser2net.yaml. A file with another name or
path may be specified using the -c option.
The yaml configuration file is described in ser2net.yaml(5)
SIGNALS
SIGHUP
If ser2net receives a SIGHUP, it will reread it configuration file and make the appropriate changes.
If an in use connection is changed or deleted, the actual change will not occur until the port is
disconnected, except that if you disable a connection it will kick the users off.
ser2net uses the name (the connection alias) of the connection to tell if it is new, changed or
deleted. If the new configuration file has a connection with the same name, it is treated as a
change.
This has some unusual interactions with connections that allow more than one simultaneous
connection. It works just like the other port, but the accepter is disabled and new connections
will not be accepted until all the existing connections are closed.
ERRORS
All error output after startup goes to syslog, not standard output, unless you use the -d option.
FILES
/etc/ser2net/ser2net.yaml, /etc/ser2net/ser2net.key, /etc/ser2net/ser2net.crt, /usr/share/ser2net
SEE ALSO
telnet(1), ser2net.yaml(5), hosts_access(5)
KNOWN PROBLEMS
None.
AUTHOR
Corey Minyard <minyard@acm.org>