Provided by: iproute2_6.1.0-1ubuntu6_amd64 
NAME
TAPRIO - Time Aware Priority Shaper
SYNOPSIS
tc qdisc ... dev dev parent classid [ handle major: ] taprio num_tc tcs
map P0 P1 P2 ... queues count1@offset1 count2@offset2 ...
base-time base-time clockid clockid
sched-entry <command 1> <gate mask 1> <interval 1>
sched-entry <command 2> <gate mask 2> <interval 2>
sched-entry <command 3> <gate mask 3> <interval 3>
sched-entry <command N> <gate mask N> <interval N>
DESCRIPTION
The TAPRIO qdisc implements a simplified version of the scheduling state machine defined by IEEE
802.1Q-2018 Section 8.6.9, which allows configuration of a sequence of gate states, where each gate state
allows outgoing traffic for a subset (potentially empty) of traffic classes.
How traffic is mapped to different hardware queues is similar to mqprio(8) and so the map and queues
parameters have the same meaning.
The other parameters specify the schedule, and at what point in time it should start (it can behave as
the schedule started in the past).
PARAMETERS
num_tc Number of traffic classes to use. Up to 16 classes supported.
map
The priority to traffic class map. Maps priorities 0..15 to a specified traffic class. See
mqprio(8) for more details.
queues
Provide count and offset of queue range for each traffic class. In the format, count@offset.
Queue ranges for each traffic classes cannot overlap and must be a contiguous range of queues.
base-time
Specifies the instant in nanoseconds, using the reference of clockid, defining the time when the
schedule starts. If 'base-time' is a time in the past, the schedule will start at
base-time + (N * cycle-time)
where N is the smallest integer so the resulting time is greater than "now", and "cycle-time" is
the sum of all the intervals of the entries in the schedule;
clockid
Specifies the clock to be used by qdisc's internal timer for measuring time and scheduling events.
This argument must be omitted when using the full-offload feature (flags 0x2), since in that case,
the clockid is implicitly /dev/ptpN (where N is given by ethtool -T eth0 | grep 'PTP Hardware
Clock' ), and therefore not necessarily synchronized with the system's CLOCK_TAI.
sched-entry
There may multiple sched-entry parameters in a single schedule. Each one has the
sched-entry <command> <gatemask> <interval>
format. The only supported <command> is "S", which means "SetGateStates", following the IEEE
802.1Q-2018 definition (Table 8-7). <gate mask> is a bitmask where each bit is a associated with a
traffic class, so bit 0 (the least significant bit) being "on" means that traffic class 0 is
"active" for that schedule entry. <interval> is a time duration, in nanoseconds, that specifies
for how long that state defined by <command> and <gate mask> should be held before moving to the
next entry.
flags
This is a bit mask which specifies different modes for taprio.
0x1 Enables the txtime-assist feature. In this mode, taprio will set the transmit timestamp
depending on the interval in which the packet needs to be transmitted. It will then
utililize the etf(8) qdisc to sort and transmit the packets at the right time. The second
example can be used as a reference to configure this mode.
0x2 Enables the full-offload feature. In this mode, taprio will pass the gate control list to
the NIC which will execute it cyclically in hardware. When using full-offload, there is no
need to specify the clockid argument.
The txtime-assist and full-offload features are mutually exclusive, i.e. setting flags to
0x3 is invalid.
txtime-delay
This parameter is specific to the txtime offload mode. It specifies the maximum time a packet
might take to reach the network card from the taprio qdisc. The value should always be greater
than the delta specified in the etf(8) qdisc.
EXAMPLES
The following example shows how an traffic schedule with three traffic classes ("num_tc 3"), which are
separated different traffic classes, we are going to call these TC 0, TC 1 and TC 2. We could read the
"map" parameter below as: traffic with priority 3 is classified as TC 0, priority 2 is classified as TC 1
and the rest is classified as TC 2.
The schedule will start at instant 1528743495910289987 using the reference CLOCK_TAI. The schedule is
composed of three entries each of 300us duration.
# tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
base-time 1528743495910289987 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 300000 \
clockid CLOCK_TAI
Following is an example to enable the txtime offload mode in taprio. See etf(8) for more information
about configuring the ETF qdisc.
# tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@0 1@0 \
base-time 1528743495910289987 \
sched-entry S 01 300000 \
sched-entry S 02 300000 \
sched-entry S 04 400000 \
flags 0x1 \
txtime-delay 200000 \
clockid CLOCK_TAI
# tc qdisc replace dev $IFACE parent 100:1 etf skip_skb_check \
offload delta 200000 clockid CLOCK_TAI
The following is a schedule in full offload mode. The base-time is 200 ns and the cycle-time is
implicitly calculated as the sum of all sched-entry durations (i.e. 20 us + 20 us + 60 us = 100 us).
Although the base-time is in the past, the hardware will start executing the schedule at a PTP time equal
to the smallest integer multiple of 100 us, plus 200 ns, that is larger than the NIC's current PTP time.
# tc qdisc add dev eth0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 200 \
sched-entry S 80 20000 \
sched-entry S a0 20000 \
sched-entry S df 60000 \
flags 0x2
AUTHORS
Vinicius Costa Gomes <vinicius.gomes@intel.com>