Provided by: atm-tools_2.5.1-5.1build1_amd64 bug

NAME

       atmsigd.conf - configuration file for the ATM signaling demon

SYNOPSIS

       /etc/atmsigd.conf

DESCRIPTION

       atmsigd.conf  contains  configuration  data for atmsigd.  atmsigd reads atmsigd.conf after
       parsing the command line options, before connecting to the ATM network.

       Configuration parameters are arranged in functional groups. In order to set  a  parameter,
       the  name  of  the group, the name of the parameter, and the parameter value(s) have to be
       specified, e.g.

            sig level debug

       decreases the logging threshold for messages related to signaling to the debug level.  The
       following options are recognized:

       debug dump path
              Specifies  the  directory  to  which  atmsigd will write status and trace dumps. If
              tracing is not yet enabled, the trace  size  is  automatically  set  to  a  (small)
              default value.

       debug level level
              Sets  the  default  debug  level  to  level. level can be any of debug, info, warn,
              error, and fatal. Only messages with the same or a higher priority than  the  debug
              level are printed.  Note that the command-line option -d generates even more output
              (e.g. hexdumps of all packets passing between atmsigd and the network)  than  debug
              level debug.

       debug log path
              Specifies the file to which atmsigd writes logging messages. When using the special
              file name syslog, messages are send to the system logger instead. Log messages  are
              written  to standard output if no log file is specified. Writing to standard output
              can also be explicitly requested by using the special file name stderr.

       debug trace [number]
              Enables tracing and optionally sets the number of entries that should  be  kept  in
              the trace buffer. A (small) default is used if the number is omitted.

       io level level
              Sets the debug level for IO-related messages to level.

       io max_rate rate
              Sets  the  rate  to signal if an application requests the "maximum". See qos(7) for
              the syntax to use for expressing the rate.  The  default  maximum  rate  is  353207
              cells/second  (OC3).  (Note that the value of max_rate does not constrain the rates
              an application can explicitly request.)

       io qos qos
              Configures the signaling VC to use the specified QOS (see qos(7) for  the  syntax).
              By default, UBR at link speed is used on the signaling VC.

       io vc [itf.]vpi.vci
              Uses the specified VC for signaling messages instead of the usual 0.0.5.

       saal level level
              Sets the debug level for messages related to SAAL (i.e. SSCF and SSCOP) to level.

       sig level level
              Sets the debug level for messages related to signaling (Q.2931 or ISP) to level.

       sig mode mode
              Set  the  mode  of  operation. The following modes are available: user for the user
              side, network for the network side, and switch  for  operation  in  a  switch.  The
              default behaviour is user.

       sig uni30
              Use  UNI  3.0 signaling. If specified together with sig uni31, this option sets UNI
              3.1 signaling with a few backwards-compatibility extensions.

       sig uni31
              Use UNI 3.1 signaling. This option can be combined with sig uni30 (see above).

       sig uni40
              Use UNI 4.0 signaling. This option can be combined with sig q.2963.1 (see below).

       sig q.2963.1
              Enable peak cell rate renegotiation. This option is only  available  with  UNI  4.0
              signaling.

       sig vpci vpci itf itf
              Sets  up  a very simplistic type of routing. All calls with VPCI values equal to or
              greater than vpci will be routed to itf, and their VPI values will be  set  to  the
              signaled  VPCI  minus  vpci.  Multiple  sig  vpci entries can be used to support an
              arbitrary number of interfaces.  Example: with sig vpci 4 itf 1,  a  call  signaled
              for  VPCI/VCI  0.x  is routed to 0.0.x, a call signaled for 6.y is routed to 1.2.y,
              etc.

       policy level level
              Sets the debug level for messages related to policy decisions to level.

       policy decision direction address
              Takes the specified decision for calls from or to address.  decision can be  either
              allow  or  reject. direction is either from or to. The address may be wildcarded by
              prepending a slash and the number of significant bits  (NSAP)  or  digits  (E.164).
              The  rules are searched in the order in which they appear in atmsigd.conf until the
              first match. If no rule matches, the call is allowed.

       entity [itf.]vpi.vci { options ... }
              Activates a signaling entity on that  specific  VC.  Multiple  entity  clauses  can
              appear  in  the  same  configuration.  When  using  entity, the option io vc is not
              available.  entity is optionally followed by the  following  options,  enclosed  in
              curly  braces:  vpci (corresponds to sig vpci), mode (corresponds to sig mode), qos
              (corresponds to vc qos), route, and default. The last  two  options  determine  how
              outbound calls are routed. The route option is followed by an address in the format
              used for addresses in policy. If no route entry matches the called party number  of
              an outbound call, the entry marked with default is selected.

       When  setting  multiple  parameters  in  the same group, the group name doesn't have to be
       repeated if it is followed by the parameters in curly braces.  Example:

           debug {
               level warn
               dump /var/tmp
               log syslog
               trace 100
           }

       Line breaks can  be  inserted  in  atmsigd.conf  wherever  spaces  or  tabs  are  allowed.
       Everything  between  a  `#'  and  the  end  of  the  line is considered a comment. The `#'
       character cannot be escaped.

       If an option is specified in atmsigd.conf and on the command line, the  command  line  has
       priority.

COMPATIBILITY

       Certain  options used by past versions of atmsigd but no longer documented on the man page
       are still recognized and supported, but they also yield a warning message. Future versions
       of atmsigd will not recognize those options.

AUTHOR

       Werner Almesberger, EPFL ICA <Werner.Almesberger@epfl.ch>

SEE ALSO

       atmsigd(8), qos(7), syslogd(8)