Provided by: freebsd-manpages_12.2-2_all bug

NAME

     wb — Winbond W89C840F Fast Ethernet device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device miibus
           device wb

     Alternatively, to load the driver as a module at boot time, place the following line in
     loader.conf(5):

           if_wb_load="YES"

DEPRECATION NOTICE

     The wb driver is not present in FreeBSD 13.0 and later.  See
     https://github.com/freebsd/fcp/blob/master/fcp-0101.md for more information.

DESCRIPTION

     The wb driver provides support for PCI Ethernet adapters and embedded controllers based on
     the Winbond W89C840F Fast Ethernet controller chip.  The 840F should not be confused with
     the 940F, which is an NE2000 clone and only supports 10Mbps speeds.

     The Winbond controller uses bus master DMA and is designed to be a DEC 'tulip' workalike.
     It differs from the standard DEC design in several ways: the control and status registers
     are spaced 4 bytes apart instead of 8, and the receive filter is programmed through
     registers rather than by downloading a special setup frame via the transmit DMA engine.
     Using an external PHY, the Winbond chip supports both 10 and 100Mbps speeds in either full
     or half duplex.

     The wb driver supports the following media types:

     autoselect            Enable autoselection of the media type and options.  This is only
                           supported if the PHY chip attached to the Winbond controller supports
                           NWAY autonegotiation.  The user can manually override the autoselected
                           mode by adding media options to the /etc/rc.conf file.

     10baseT/UTP           Set 10Mbps operation.  The mediaopt option can also be used to select
                           either full-duplex or half-duplex modes.

     100baseTX             Set 100Mbps (Fast Ethernet) operation.  The mediaopt option can also
                           be used to select either full-duplex or half-duplex modes.

     The wb driver supports the following media options:

     full-duplex           Force full duplex operation.

     half-duplex           Force half duplex operation.

     Note that the 100baseTX media type is only available if supported by the adapter.  For more
     information on configuring this device, see ifconfig(8).

HARDWARE

     The wb driver supports Winbond W89C840F based Fast Ethernet adapters and embedded
     controllers including:

        Trendware TE100-PCIE

DIAGNOSTICS

     wb%d: couldn't map memory  A fatal initialization error has occurred.

     wb%d: couldn't map interrupt  A fatal initialization error has occurred.

     wb%d: watchdog timeout  The device has stopped responding to the network, or there is a
     problem with the network connection (cable).

     wb%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

     wb%d: no memory for tx list  The driver failed to allocate an mbuf for the transmitter ring
     when allocating a pad buffer or collapsing an mbuf chain into a cluster.

     wb%d: chip is in D3 power state -- setting to D0  This message applies only to adapters
     which support power management.  Some operating systems place the controller in low power
     mode when shutting down, and some PCI BIOSes fail to bring the chip out of this state before
     configuring it.  The controller loses all of its PCI configuration in the D3 state, so if
     the BIOS does not set it back to full power mode in time, it will not be able to configure
     it correctly.  The driver tries to detect this condition and bring the adapter back to the
     D0 (full power) state, but this may not be enough to return the driver to a fully
     operational condition.  If you see this message at boot time and the driver fails to attach
     the device as a network interface, you will have to perform second warm boot to have the
     device properly configured.

     Note that this condition only occurs when warm booting from another operating system.  If
     you power down your system prior to booting FreeBSD, the card should be configured
     correctly.

SEE ALSO

     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The wb device driver first appeared in FreeBSD 3.0.

AUTHORS

     The wb driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

BUGS

     The Winbond chip seems to behave strangely in some cases when the link partner switches
     modes.  If for example both sides are set to 10Mbps half-duplex, and the other end is
     changed to 100Mbps full-duplex, the Winbond's receiver suddenly starts writing trash all
     over the RX descriptors.  The wb driver handles this by forcing a reset of both the
     controller chip and attached PHY.  This is drastic, but it appears to be the only way to
     recover properly from this condition.