Provided by: freebsd-manpages_12.2-2_all bug

NAME

     isp — Qlogic based SPI and FibreChannel SCSI Host Adapters

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device scbus
           device isp
           device ispfw

     Alternatively, to load the driver as a module at boot time, place the following lines in
     loader.conf(5):

           isp_load="YES"
           ispfw_load="YES"

DESCRIPTION

     This driver provides access to SPI or FibreChannel SCSI devices.

     SPI supports initiator mode for Ultra SCSI and wide mode transactions for SCSI, Ultra2 LVD
     (1080, 1280), and Ultra3 LVD (10160, 12160).

     Fibre Channel supports initiator and target modes of FCP SCSI profile, utilizing Class 3 and
     Class 2 (2200 and later) connections.  Support is available for Public and Private loops,
     Point-to-Point and Fabric connections.

     FC-Tape is supported on 4Gb (2400) and newer controllers.  FC-Tape is highly recommended for
     connections to tape drives that support it.  It encompasses four elements from the T-10
     FCP-4 specification:

              Precise Delivery of Commands

              Confirmed Completion of FCP I/O Operations

              Retransmission of Unsuccessfully Transmitted IUs

              Task Retry Identification

     Together these features allow for link level error recovery with tape devices.  Without it,
     an initiator cannot, for instance, tell whether a tape write command that has timed out
     resulted in all, part or none of the data going to the tape drive.  FC-Tape is automatically
     enabled when connecting controller that supports it to a target that supports it.  It may be
     disabled using configuration and hint options described below.

FIRMWARE

     Firmware loading is supported if the ispfw(4) module is loaded.  It is strongly recommended
     that you use the firmware available from ispfw(4) as it is the most likely to have been
     tested with this driver.

HARDWARE

     Cards supported by the isp driver include:

           Qlogic 1000
                   Fast Wide, Ultra Fast Wide cards, Single Ended or Differential SBus cards.

           Qlogic 1020
                   Fast Wide and Differential Fast Wide SCSI PCI cards.

           Qlogic 1040
                   Ultra Wide and Differential Ultra Wide SCSI PCI cards.  Also known as the DEC
                   KZPBA-CA (single ended) and KZPBA-CB (HVD differential).

           Qlogic 1080
                   LVD Ultra2 Wide SCSI PCI cards.

           Qlogic 10160
                   LVD Ultra3 Wide SCSI PCI cards.

           Qlogic 1240
                   Dual Bus Ultra Wide and Differential Ultra Wide SCSI PCI cards.

           Qlogic 1280
                   Dual Bus LVD Ultra2 Wide SCSI PCI cards.

           Qlogic 12160
                   Dual Bus LVD Ultra3 Wide SCSI PCI cards.

           Qlogic 210X
                   Copper and Optical Fibre Channel Arbitrated Loop PCI cards (single, dual).

           Qlogic 220X
                   Copper and Optical Fibre Channel Arbitrated Loop PCI cards (single, dual,
                   quad).

           Qlogic 2300
                   Optical 2Gb Fibre Channel PCI cards.

           Qlogic 2312
                   Optical 2Gb Fibre Channel PCI cards.

           Qlogic 234X
                   Optical 2Gb Fibre Channel PCI cards (2312 chipset, single and dual attach).

           Qlogic 2322
                   Optical 2Gb Fibre Channel PCIe cards.

           Qlogic 200
                   Dell branded version of the QLogic 2312.

           Qlogic 2422
                   Optical 4Gb Fibre Channel PCI cards.

           Qlogic 246x (aka 2432)
                   Optical 4Gb Fibre Channel PCIe cards.

           Qlogic 256x (aka 2532)
                   Optical 8Gb Fibre Channel PCIe cards.

           Qlogic 267x/836x (aka 2031/8031)
                   Optical 16Gb FC/FCoE PCIe cards.

           Qlogic 2690/2692/2694 (aka 2684/2692)
                   Optical 16Gb Fibre Channel PCIe cards.

           Qlogic 2740/2742/2764 (aka 2722/2714)
                   Optical 32Gb Fibre Channel PCIe cards.

CONFIGURATION OPTIONS

     Target mode support for Fibre Channel adapters may be enabled with the

     options ISP_TARGET_MODE

     option.

     To disable FC-Tape, use the following configuration option:

     options ISP_FCTAPE_OFF

     Note that even if the ISP_FCTAPE_OFF option is used, it may be overridden by the fctape hint
     described below.

BOOT OPTIONS

     The following options are switchable by setting values in /boot/device.hints.

     They are:

     hint.isp.N.msi
             Limit on number of Message Signaled Interrupts (MSI) to be used.

     hint.isp.N.msix
             Limit on number of Extended Message Signaled Interrupts (MSI-X) to be used.

     hint.isp.N.fwload_disable
             A hint value to disable loading of firmware ispfw(4).

     hint.isp.N.ignore_nvram
             A hint value to ignore board NVRAM settings for.  Otherwise use NVRAM settings.

     hint.isp.N.fullduplex
             A hint value to set full duplex mode.

     hint.isp.N.topology
             A hint value to select topology of connection.  Supported values are:

             lport       Prefer loopback and fallback to point to point.
             nport       Prefer point to point and fallback to loopback.
             lport-only  Loopback only.
             nport-only  Point to point only.

     hint.isp.N.portwwn
             This should be the full 64 bit World Wide Port Name you would like to use,
             overriding the value in NVRAM for the card.

     hint.isp.N.nodewwn
             This should be the full 64 bit World Wide Node Name you would like to use,
             overriding the value in NVRAM for the card.

     hint.isp.N.iid
             A hint to override or set the Initiator ID or Loop ID.  For Fibre Channel cards in
             Local Loop topologies it is strongly recommended that you set this value to non-
             zero.

     hint.isp.N.role
             A hint to define default role for isp instance (0 -- none, 1 -- target, 2 --
             initiator, 3 -- both).

     hint.isp.N.debug
             A hint value for a driver debug level (see the file /usr/src/sys/dev/isp/ispvar.h
             for the values.

     hint.isp.N.vports
             A hint to create specified number of additional virtual ports.

     hint.isp.N.nofctape
             Set this to 1 to disable FC-Tape operation on the given isp instance.

     hint.isp.N.fctape
             Set this to 1 to enable FC-Tape operation on the given isp instance for targets that
             support it.

SYSCTL OPTIONS

     dev.isp.N.loop_down_limit
             This value says how long to wait in seconds after loop has gone down before giving
             up and expiring all of the devices that were visible.  The default is 300 seconds (5
             minutes).  A separate (nonadjustable) timeout is used when booting to not stop
             booting on lack of FC connectivity.

     dev.isp.N.gone_device_time
             This value says how long to wait for devices to reappear if they (temporarily)
             disappear due to loop or fabric events.  While this timeout is running, I/O to those
             devices will simply be held.

     dev.isp.N.use_gff_id

     dev.isp.N.use_gft_id
             Setting those options to 0 allows to disable use of GFF_ID and GFT_ID SNS requests
             during FC fabric scan.  It may be useful if switch does not implement them
             correctly, preventing some devices from being found.  Disabling them may cause
             unneeded logins to ports not supporting target role or even FCP at all.  The default
             is 1 (enabled).

     dev.isp.N.wwnn
             This is the readonly World Wide Node Name value for this port.

     dev.isp.N.wwpn
             This is the readonly World Wide Port Name value for this port.

SEE ALSO

     da(4), intro(4), ispfw(4), sa(4), scsi(4), gmultipath(8)

AUTHORS

     The isp driver was written by Matthew Jacob originally for NetBSD at NASA/Ames Research
     Center.  Later improvement was done by
     Alexander Motin <mav@FreeBSD.org>.

BUGS

     The driver currently ignores some NVRAM settings.

     Fabric support for 2100 cards has been so problematic, and these cards are so old now that
     it is just not worth your time to try it.