Provided by: freebsd-manpages_12.2-2_all bug

NAME

     mem, kmem — memory files

SYNOPSIS

     device mem

DESCRIPTION

     The special file /dev/mem is an interface to the physical memory of the computer.  Byte
     offsets in this file are interpreted as physical memory addresses.  Reading and writing this
     file is equivalent to reading and writing memory itself.  Only offsets within the bounds of
     /dev/mem are allowed.

     Kernel virtual memory is accessed through the interface /dev/kmem in the same manner as
     /dev/mem.  Only kernel virtual addresses that are currently mapped to memory are allowed.

     On ISA the I/O memory space begins at physical address 0x000a0000 and runs to 0x00100000.
     The per-process data size for the current process is UPAGES long, and ends at virtual
     address 0xf0000000.

IOCTL INTERFACE

     Several architectures allow attributes to be associated with ranges of physical memory.
     These attributes can be manipulated via ioctl() calls performed on /dev/mem.  Declarations
     and data types are to be found in <sys/memrange.h>.

     The specific attributes, and number of programmable ranges may vary between architectures.
     The full set of supported attributes is:

     MDF_UNCACHEABLE
             The region is not cached.

     MDF_WRITECOMBINE
             Writes to the region may be combined or performed out of order.

     MDF_WRITETHROUGH
             Writes to the region are committed synchronously.

     MDF_WRITEBACK
             Writes to the region are committed asynchronously.

     MDF_WRITEPROTECT
             The region cannot be written to.

     Memory ranges are described by struct mem_range_desc:

           uint64_t        mr_base;        /∗ physical base address ∗/
           uint64_t        mr_len;         /∗ physical length of region ∗/
           int             mr_flags;       /∗ attributes of region ∗/
           char            mr_owner[8];

     In addition to the region attributes listed above, the following flags may also be set in
     the mr_flags field:

     MDF_FIXBASE
             The region's base address cannot be changed.

     MDF_FIXLEN
             The region's length cannot be changed.

     MDF_FIRMWARE
             The region is believed to have been established by the system firmware.

     MDF_ACTIVE
             The region is currently active.

     MDF_BOGUS
             We believe the region to be invalid or otherwise erroneous.

     MDF_FIXACTIVE
             The region cannot be disabled.

     MDF_BUSY
             The region is currently owned by another process and may not be altered.

     Operations are performed using struct mem_range_op:

           struct mem_range_desc   *mo_desc;
           int                     mo_arg[2];

     The MEMRANGE_GET ioctl is used to retrieve current memory range attributes.  If mo_arg[0] is
     set to 0, it will be updated with the total number of memory range descriptors.  If greater
     than 0, the array at mo_desc will be filled with a corresponding number of descriptor
     structures, or the maximum, whichever is less.

     The MEMRANGE_SET ioctl is used to add, alter and remove memory range attributes.  A range
     with the MDF_FIXACTIVE flag may not be removed; a range with the MDF_BUSY flag may not be
     removed or updated.

     mo_arg[0] should be set to MEMRANGE_SET_UPDATE to update an existing or establish a new
     range, or to MEMRANGE_SET_REMOVE to remove a range.

RETURN VALUES

     [EOPNOTSUPP]       Memory range operations are not supported on this architecture.

     [ENXIO]            No memory range descriptors are available (e.g. firmware has not enabled
                        any).

     [EINVAL]           The memory range supplied as an argument is invalid or overlaps another
                        range in a fashion not supported by this architecture.

     [EBUSY]            An attempt to remove or update a range failed because the range is busy.

     [ENOSPC]           An attempt to create a new range failed due to a shortage of hardware
                        resources (e.g. descriptor slots).

     [ENOENT]           An attempt to remove a range failed because no range matches the
                        descriptor base/length supplied.

     [EPERM]            An attempt to remove a range failed because the range is permanently
                        enabled.

FILES

     /dev/mem
     /dev/kmem

SEE ALSO

     kvm(3), memcontrol(8)

HISTORY

     The mem and kmem files appeared in Version 6 AT&T UNIX.  The ioctl interface for memory
     range attributes was added in FreeBSD 3.2.

BUGS

     Busy range attributes are not yet managed correctly.

     This device is required for all users of kvm(3) to operate.