Provided by: freebsd-manpages_12.2-2_all bug

NAME

     mps — LSI Fusion-MPT 2 IT/IR 6Gb/s Serial Attached SCSI/SATA driver

SYNOPSIS

     To compile this driver into the kernel, place these lines in the kernel configuration file:

           device pci
           device scbus
           device mps

     The driver can be loaded as a module at boot time by placing this line in loader.conf(5):

           mps_load="YES"

DESCRIPTION

     The mps driver provides support for Broadcom Ltd./Avago Tech (LSI) Fusion-MPT 2 IT/IR SAS
     controllers and WarpDrive solid state storage cards.

HARDWARE

     These controllers are supported by the mps driver:

        Broadcom Ltd./Avago Tech (LSI) SAS 2004 (4 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SAS 2008 (8 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SAS 2108 (8 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SAS 2116 (16 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SAS 2208 (8 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SAS 2308 (8 Port SAS)
        Broadcom Ltd./Avago Tech (LSI) SSS6200 Solid State Storage
        Intel Integrated RAID Module RMS25JB040
        Intel Integrated RAID Module RMS25JB080
        Intel Integrated RAID Module RMS25KB040
        Intel Integrated RAID Module RMS25KB080

CONFIGURATION

     In all tunable descriptions below, X represents the adapter number.

     To disable MSI interrupts for all mps driver instances, set this tunable value in
     loader.conf(5):

           hw.mps.disable_msi=1

     To disable MSI interrupts for a specific mps driver instance, set this tunable value in
     loader.conf(5):

           dev.mps.X.disable_msi=1

     To disable MSI-X interrupts for all mps driver instances, set this tunable value in
     loader.conf(5):

           hw.mps.disable_msix=1

     To disable MSI-X interrupts for a specific mps driver instance, set this tunable value in
     loader.conf(5):

           dev.mps.X.disable_msix=1

     To set the maximum number of DMA chains allocated for all adapters, set this tunable in
     loader.conf(5):

           hw.mps.max_chains=NNNN

     To set the maximum number of DMA chains allocated for a specific adapter, set this tunable
     in loader.conf(5):

           dev.mps.X.max_chains=NNNN

     The default max_chains value is 16384.

     The current number of free chain frames is stored in the dev.mps.X.chain_free sysctl(8)
     variable.

     The lowest number of free chain frames seen since boot is stored in the
     dev.mps.X.chain_free_lowwater sysctl(8) variable.

     The number of times that chain frame allocations have failed since boot is stored in the
     dev.mps.X.chain_alloc_fail sysctl(8) variable.  This can be used to determine whether the
     max_chains tunable should be increased to help performance.

     The current number of active I/O commands is shown in the dev.mps.X.io_cmds_active sysctl(8)
     variable.

     To set the maximum number of pages that will be used per I/O for all adapters, set this
     tunable in loader.conf(5):

           hw.mps.max_io_pages=NNNN

     To set the maximum number of pages that will be used per I/O for a specific adapter, set
     this tunable in loader.conf(5):

           dev.mps.X.max_io_pages=NNNN

     The default max_io_pages value is -1, meaning that the maximum I/O size that will be used
     per I/O will be calculated using the IOCFacts values stored in the controller.  The lowest
     value that the driver will use for max_io_pages is 1, otherwise IOCFacts will be used to
     calculate the maximum I/O size.  The smaller I/O size calculated from either max_io_pages or
     IOCFacts will be the maximum I/O size used by the driver.

     The highest number of active I/O commands seen since boot is stored in the
     dev.mps.X.io_cmds_highwater sysctl(8) variable.

     Devices can be excluded from mps control for all adapters by setting this tunable in
     loader.conf(5):

           hw.mps.exclude_ids=Y

     Y represents the target ID of the device.  If more than one device is to be excluded, target
     IDs are separated by commas.

     Devices can be excluded from mps control for a specific adapter by setting this tunable in
     loader.conf(5):

           dev.mps.X.exclude_ids=Y

     Y represents the target ID of the device.  If more than one device is to be excluded, target
     IDs are separated by commas.

     The adapter can issue the StartStopUnit SCSI command to SATA direct-access devices during
     shutdown.  This allows the device to quiesce powering down.  To control this feature for all
     adapters, set the

           hw.mps.enable_ssu

     tunable in loader.conf(5) to one of these values:

           0       Do not send SSU to either HDDs or SSDs.

           1       Send SSU to SSDs, but not to HDDs.  This is the default value.

           2       Send SSU to HDDs, but not to SSDs.

           3       Send SSU to both HDDs and SSDs.

     To control this feature for a specific adapter, set this tunable value in loader.conf(5):

           dev.mps.X.enable_ssu

     The same set of values are valid as when setting this tunable for all adapters.

     SATA disks that take several seconds to spin up and fail the SATA Identify command might not
     be discovered by the driver.  This problem can sometimes be overcome by increasing the value
     of the spinup wait time in loader.conf(5) with the

           hw.mps.spinup_wait_time=NNNN

     tunable.  NNNN represents the number of seconds to wait for SATA devices to spin up when the
     device fails the initial SATA Identify command.

     Spinup wait times can be set for specific adapters in loader.conf(5): with the

           dev.mps.X.spinup_wait_time=NNNN

     tunable.  NNNN is the number of seconds to wait for SATA devices to spin up when they fail
     the initial SATA Identify command.

     The driver can map devices discovered by the adapter so that target IDs corresponding to a
     specific device persist across resets and reboots.  In some cases it is possible for devices
     to lose their mapped IDs due to unexpected behavior from certain hardware, such as some
     types of enclosures.  To overcome this problem, a tunable is provided that will force the
     driver to map devices using the Phy number associated with the device.  This feature is not
     recommended if the topology includes multiple enclosures/expanders.  If multiple
     enclosures/expanders are present in the topology, Phy numbers are repeated, causing all
     devices at these Phy numbers except the first device to fail enumeration.  To control this
     feature for all adapters, set the

           hw.mps.use_phy_num

     tunable in loader.conf(5) to one of these values:

           -1      Only use Phy numbers to map devices and bypass the driver's mapping logic.

           0       Never use Phy numbers to map devices.

           1       Use Phy numbers to map devices, but only if the driver's mapping logic fails
                   to map the device that is being enumerated.  This is the default value.

     To control this feature for a specific adapter, set this tunable value in loader.conf(5):

           dev.mps.X.use_phy_num

     The same set of values are valid as when setting this tunable for all adapters.

DEBUGGING

     Driver diagnostic printing is controlled in loader.conf(5) by using the global
     hw.mps.debug_level and per-device dev.mps.X.debug_level tunables.  One can alter the debug
     level for any adapter at run-time using the sysctl(8) variable dev.mps.X.debug_level.

     All debug_level variables can be named by either an integer value or a text string.
     Multiple values can be specified together by either ORing the integer values or by providing
     a comma-separated list of names.  A text string prefixed by "+" adds the specified debug
     levels to the existing set, while the prefix "-" removes them from the existing set.  The
     current debug_level status is reported in both formats for convenience.  The following
     levels are available:

           Flag      Name        Description
           0x0001    info        Basic information (enabled by default)
           0x0002    fault       Driver faults (enabled by default)
           0x0004    event       Controller events
           0x0008    log         Logging data from controller
           0x0010    recovery    Tracing of recovery operations
           0x0020    error       Parameter errors and programming bugs
           0x0040    init        System initialization operations
           0x0080    xinfo       More detailed information
           0x0100    user        Tracing of user-generated commands (IOCTL)
           0x0200    mapping     Tracing of device mapping
           0x0400    trace       Tracing through driver functions

SEE ALSO

     cam(4), cd(4), ch(4), da(4), mpr(4), mpt(4), pci(4), sa(4), scsi(4), targ(4),
     loader.conf(5), sysctl(8)

HISTORY

     The mps driver first appeared in FreeBSD 9.0.

AUTHORS

     The mps driver was originally written by Scott Long <scottl@FreeBSD.org>.  It has been
     improved and tested by LSI Corporation, Avago Technologies (formally LSI), and Broadcom Ltd.
     (formally Avago).

     This man page was written by Ken Merry <ken@FreeBSD.org> with additional input from Stephen
     McConnell <slm@FreeBSD.org>.