Provided by: sdparm_1.12-2_amd64 
NAME
sdparm - access SCSI modes pages; read VPD pages; send simple SCSI commands.
SYNOPSIS
sdparm [--all] [--dbd] [--examine] [--flexible] [--get=STR] [--hex] [--long] [--num-desc] [--out-mask=OM]
[--page=PG[,SPG]] [--quiet] [--readonly] [--six] [--transport=TN] [--vendor=VN] [--verbose] DEVICE
[DEVICE...]
sdparm [--clear=STR] [--defaults] [--dummy] [--flexible] [--page=PG[,SPG]] [--quiet] [--readonly]
[--save] [--set=STR] [--six] [--transport=TN] [--vendor=VN] [--verbose] DEVICE [DEVICE...]
sdparm --command=CMD [--hex] [--long] [--readonly] [--verbose] DEVICE [DEVICE...]
sdparm --inquiry [--all] [--examine] [--flexible] [--hex] [--num-desc] [--page=PG[,SPG]] [--quiet]
[--readonly] [--transport=TN] [--verbose] DEVICE [DEVICE...]
sdparm --enumerate [--all] [--inquiry] [--long] [--page=PG[,SPG]] [--transport=TN] [--vendor=VN]
sdparm --inhex=FN [--all] [--flexible] [--hex] [--inquiry] [--long] [--pdt=DT] [--raw] [--six]
[--transport=TN] [--vendor=VN] [--verbose]
sdparm --wscan [--verbose]
sdparm [--help] [--version]
DESCRIPTION
This utility fetches and potentially changes SCSI device (e.g. disk) mode pages. Inquiry data including
Vital Product Data (VPD) pages can also be displayed. Commands associated with starting and stopping the
medium; loading and unloading the medium; and other housekeeping functions may also be issued by this
utility.
The first invocation shown in the synopsis is for accessing (i.e. reading) mode page fields held on the
DEVICE. The second form is for changing mode page fields held on the DEVICE. The third form is for
executing some simple SCSI commands. The fourth form (i.e. the '--inquiry ... DEVICE' form) is for
fetching and decoding VPD pages from the given DEVICE. The --enumerate form is for listing out mode or
VPD field data held by this utility (and if a DEVICE is given then it is ignored). The --inhex=FN form
decodes mode or VPD response data provided in the named file (or from stdin if FN=- is given); that data
may either be in hexadecimal or binary. The second last form is for Windows only and lists the available
storage device names; see the OPTIONS entry for --wscan. The final form is to provide command line help
or the version number (and date) of this utility.
If no options (other than DEVICE) are given then a selection of common mode page fields for that device
are listed. If the --long option is also given then a description of the fields is placed on the right of
each line. If the --all option is given then all known mode page fields for that device are listed.
Individual fields can be displayed with the --get=STR option (e.g. '--get=WCE' to fetch the state of the
Writeback Cache Enable field).
This utility completes with an exit status of 0 when successful. For other values see the EXIT STATUS
section below.
One or more DEVICE arguments can be given. The utility will essentially apply the given options to each
DEVICE in the list. If a error is detected, it is noted and the utility continues. Error value 5 (file
open or close problem) is treated as lower priority when other errors are detected. The exit status is
the most recently detected error value (excluding error value 5 if other errors have been detected). If
all actions succeed the exit status is zero.
By default this utility shows mode pages that are common to all transport protocols. These are termed as
"generic" mode pages. If there is no match on a generic mode page name or field then those pages specific
to the SAS transport are checked. Transport protocol specific mode pages are selected with the
--transport=TN option. See the TRANSPORT section below. Vendor specific mode pages are selected with the
--vendor=VN option. See the VENDORS section below.
Although originally for SCSI disks (or storage devices that appear to the OS as SCSI disks) many of the
mode pages are for other SCSI device types. These include CD/DVD players that use the ATAPI (or any
other) transport, SCSI tapes drives and SCSI enclosures.
When the --inquiry option is given without a page number then the Device Identification VPD page (page
number 0x83) is requested and if found it is decoded and output. If no page number is given and the --all
option is given then a list of VPD page names (but not their contents) supported by the DEVICE is output.
When both the --inquiry and --page=PG options are given then the VPD page can be specified as an
abbreviation (e.g. "sp" for the SCSI ports VPD page) or numerically (e.g. "0x88"). If a VPD page is
returned by the DEVICE but sdparm cannot decode it or the --hex option is given then it is output in hex.
OPTIONS
Mandatory arguments to long options are mandatory for short options as well. If an option takes a
numeric argument then that argument is assumed to be decimal unless otherwise indicated (e.g. with a
leading "0x" or a trailing "h"). The options are in alphabetical order, based on the long option name.
-a, --all
output all recognized fields for the device type (e.g. disk) of the DEVICE. Without this option
(or the --page=PG[,SPG] option) the default action is to output a relatively small number of
commonly used fields from different pages. When a specific (mode) page number is given with the
--page=PG[,SPG] option then all the fields of that page are output (irrespective of the setting of
this option). For this option's action when used with the --enumerate option see the ENUMERATE
section below.
When used together with the --inquiry option and a DEVICE, the Supported VPD Pages VPD page [0x0]
is output. When this option is used twice (short form: '-iaa') then all VPD pages (listed in the
Supported VPD Pages VPD page) are output.
By default --inhex=FN will only decode the first mode page found in FN. With this option, more
mode pages will be decoded if present. When --transport=TN or --vendor=VN is also given then if a
given mode page is not defined for that transport or vendor, then it is decoded as a generic mode
page.
-c, --clear=STR
In its simplest form STR contains a field acronym_name or a field numerical descriptor. In the
absence of an explicit value argument (e.g. '--clear=WCE=1'), the field has its value cleared to
zero. See the PARAMETERS section below.
-C, --command=CMD
Perform given CMD. See section below on COMMANDS. To enumerate supported commands use '-e -C x'
(using any CMD name, valid or otherwise).
-B, --dbd
disable block descriptors. This is a bit in MODE SENSE cdbs that rarely needs to be set. One known
case is a MODE SENSE 6 issued to a Reduced Block Commands (RBC) device where the RBC standard says
it shall be set.
-D, --defaults
sets the given mode page to its default values. Requires the --page=PG[,SPG] option to be given to
specify the mode page. To make the default mode page values also the saved mode page values, use
the --save option as well.
when this option is used twice, the current values in all modes pages are reverted to their
defaults. If the --save option is given as well, then the current and saved values in all modes
pages are reverted to their defaults. This feature uses the RTD bit in the MODE SELECT command
which was added in draft SPC-5 revision 11.
-d, --dummy
when set inhibits changes being placed in the DEVICE's mode page. Instead the mode data that
would have been sent to a MODE SELECT command, is output in ASCII hex to the console. This option
is mainly for testing.
-e, --enumerate
lists out descriptive information about the pages and fields known to this utility. Ignores the
DEVICE argument and other options apart from the --all, --inquiry, --long, --page=PG[,SPG],
--transport=TN and --vendor=VN. If --enumerate is given without other options then the known
(generic) mode pages are listed. See the ENUMERATE section below.
-E, --examine
for mode pages only those with known field names are probed when the --all option is given. For
VPD pages only those pages listed in "Supported VPD pages page" are decoded. In both cases some
pages may be missed. With this option (i.e. --examine) all mode and VPD pages can be probed.
For mode pages, this option will probe all mode pages from page number 0x0 to 0x3e. To probe mode
subpages give a mode page number with --page=PG and then all subpages (from 0x0 to 0xfe) are
probed.
For VPD pages, use this option with --inquiry. This will cause all VPD pages from 0x0 to 0xbf to
be probed by default. A sequence of VPD pages can be probed with --page=PG[,SPG] in which case VPD
pages from PG (lower number) to SPG (high number) inclusive are probed. Vendor specific VPD pages
run from 0xc0 to 0xff and can be probed by setting SPG from 0xc0 to 0xff.
-f, --flexible
Some devices, bridges and/or drivers attempt crude transformations between mode sense 6 and 10
byte commands without correctly rebuilding the response. This will cause the response to be
mis-interpreted (usually with an error saying the response is malformed). With this option, the
length of the response is checked, and if it looks wrong, various corrections are attempted. This
option will also allow mode pages that don't belong to the current device's peripheral type to be
listed.
-g, --get=STR
In its simplest form STR contains a field acronym_name or a field numerical descriptor. The field
is fetched from mode page. See the PARAMETERS section below. The --long and --hex options effect
the output format. Also if a value of "1" is given (e.g. '--get=WCE=1') only the current value is
output (i.e. not the change mask, the default value and the saved value).
-h, --help
output the usage message then exit.
-H, --hex
rather than trying to decode mode (or VPD) pages, print them out in hex. When used with the
--get=STR option the corresponding current, changeable, default and saved values are output in
hex, prefixed by "0x" and space separated. If a value of "1" is given with the --get=STR option
(e.g. '--get=WCE=1') then only the current value is output in hex, prefixed by "0x". If a value of
"2" is given with the --get=STR option then only the current value is output as a (signed)
integer. This option can be used multiple times (e.g. '-HH'). Useful with the ATA Information VPD
page which usually outputs its IDENTIFY (PACKET) DEVICE response in 16 bit hex words; with '-HH'
outputs that response in hex bytes; with '-HHH' outputs the same response in a format suitable for
'hdparm --Istdin' to decode.
Mode page output with the '-HHH' option is suitable for a later invocation of sdparm with the
--inhex=FN option.
-i, --inquiry
output a VPD page which is in the response of a SCSI INQUIRY command sent to DEVICE. In the
absence of this option the default action is to output mode pages. If the --inquiry option is
given without the --page=PG[,SPG] option then the device identification VPD page (0x83) is decoded
and output. If this option and the --all option are given then the supported VPD pages page (0x0)
is decoded and output.
-I, --inhex=FN
FN is expected to be a file name (or '-' for stdin) which contains ASCII hexadecimal (or binary)
representing the response to MODE SENSE(10). If --six is also given then the response from MODE
SENSE(6) is assumed. A MODE SENSE response contains a mode parameter header, then 0 or more block
descriptors followed by one or more mode pages. This utility will only decode the first mode page
unless the --all option is given. In order to decode a mode page the peripheral device type is
often needed and can be supplied with the --pdt=DT option. If the --pdt=DT is not given then a
mode page found in two device type standards (e.g. SBC and SSC) may be decoded twice.
If --inquiry is given then FN is interpreted as the response data of a single VPD page.
The hexadecimal in FN should be arranged as 1 or 2 digits representing a byte each of which is
whitespace or comma separated. Anything from and including a hash mark to the end of line is
ignored. If the --raw option is given then FN is treated as binary.
-l, --long
output extra information. In the case of mode page fields a description (with units if applicable)
is output to the right. If used twice, then for some fields more information about its values is
given on one or more following lines, each prefixed by a tab character. For usage with --enumerate
see the ENUMERATE section below.
When this option is used along with --command=capacity then the READ CAPACITY(16) is sent to the
DEVICE and if successful its extended response is output.
-n, --num-desc
for a mode page that can have descriptors, the number of descriptors for the given page on the
DEVICE is output. Otherwise 0 is output.
-o, --out-mask=OM
OM is a bit mask for mode page selections that will be printed/output. The 0x1 value is for the
'current' values, 0x2 is for the 'changeable' values, 0x4 is for the 'default' values and 0x8 is
for the 'saveable' values. The default value is 0xf (i.e. the OR of all four values set). The
option is useful for limiting the amount of output with the '-HHH'.
-p, --page=PG[,SPG]
supply the page number (PG) and optionally the sub page number (SPG) of the mode (or VPD) page to
fetch. These numbers are interpreted as decimal unless prefixed with "0x" or a trailing. Sub page
numbers are only valid for mode pages (not VPD pages). Alternatively an abbreviation for a page
can be given (see next entry).
-p, --page=STR
a two or three letter abbreviation for a page can be given. Known mode page abbreviations are
checked first followed by known VPD page abbreviations. For example '--page=ca' matches the
caching mode page. If no match is found then an error is issued and a list of possibilities in the
current context is given (so '-p x' can be quite useful). If the STR matches a known VPD page
abbreviation then the --inquiry option is assumed. For usage with --enumerate see the ENUMERATE
section below.
-P, --pdt=DT
This option is only active when the --inhex=FN option is given. DT is the peripheral Device Type,
a value between 0 and 31 and can be found in the response to the INQUIRY command. The default
value is -1 (which may also be given for DT) and it is interpreted as SPC (i.e. common mode pages)
or as a wild card. If available this option should be supplied with the --inhex=FN option.
-q, --quiet
suppress output of device name followed by the vendor, product and revision strings fetched from
an INQUIRY response. Without this option such a line is typically the first line output by sdparm.
Reduces output from the device identification VPD page, typically to one line (or none) for each
of di_lu, di_port, di_target and di_asis.
If this option is used twice then additionally mode page output suppresses the changeable, default
and saved values that are usually shown in braces, if available.
-r, --readonly
override other logic to open DEVICE in read-only mode. The default setting of the open
read-only/read-write mode depends on the operation requested (e.g. a --set=STR operation by
default will try a read-write mode open on DEVICE). This option may be useful if a command is
being sent to an ATA disk via a SCSI command set. For example in Linux '-C stop' may require this
option to stop an ATA disk being restarted immediately.
-R, --raw
this option is only active when used with the --inhex=FN option. When this option is given then
the file FN is interpreted as binary; the default action (i.e. when this option is not given) is
to interpret FN as ASCII hexadecimal.
-S, --save
when a mode page is being modified (by using the --clear=STR and/or --set=STR options) then the
default action is to modify only the current values mode page. When this option is given then the
corresponding value(s) in the saved values mode page is also changed. The next time the device is
power cycled (or reset) the saved values mode page becomes (i.e. is copied to) the current values
mode page. This option sets the SP field in the MODE SELECT command. See NOTES section below.
-s, --set=STR
in its simplest form STR contains a field acronym_name or a field numerical descriptor. In the
absence of an explicit value, each acronym_name has its value set to (all) ones. This means a 16
bit field will be set to 0xffff which is 65535 in decimal. Alternatively each acronym_name or
numerical descriptor may be followed by "=<n>" where <n> is the value to set that field to. See
the PARAMETERS section below.
-6, --six
The default action of this utility is to issue MODE SENSE and MODE SELECT SCSI commands with 10
byte cdbs. When this option is given the 6 byte cdb variants are used. RBC and old SCSI devices
may need this option. This utility outputs a suggestion to use this option if the SCSI status
indicates that the 10 byte cdb variant is not supported.
The SPC-4 standard (and SPC-5 drafts) include a note stating that implementers migrate away from
the SCSI MODE SELECT(6) and MODE SENSE(6) commands in favour of the 10 byte variants (e.g. MODE
SEMSE(10)).
-t, --transport=TN
Specifies the transport protocol where TN is either a number in the range 0 to 15 (inclusive) or
an abbreviation (e.g. "fcp" for the Fibre Channel Protocol). Some transports accept multiple
abbreviations, for example srp (SCSI RDMA Protocol) and ib (short for InfiniBand) both are
accepted for transport protocol 0x4 . Also both upper and lower case are accepted so iscsi and
iSCSI are accepted for transport protocol 0x5 . One way to list available transport protocols
numbers and their associated abbreviations is to give an invalid transport protocol name such as
'-t x'; another way is '-e -l'. N.B. The --all option may still be needed to show all available
fields.
-M, --vendor=VN
Specifies the vendor (i.e. manufacturer) where VN is either a number (0 or more) or an
abbreviation (e.g. "sea" for Seagate disk vendor specific). For tape drives "lto5" and "lto6" are
treated as vendors. One way to list the available vendor numbers and their associated
abbreviations is to give an invalid vendor number such as '-M x'; another way is '-e -l'.
This option only effects mode page decodes, not VPD pages. For vendor specific VPD pages see the
sg_vpd utility.
-v, --verbose
increase the level of verbosity, (i.e. debug output). In some cases more decoding is done (e.g.
fields within a standard INQUIRY response).
-V, --version
print the version string and then exit.
-w, --wscan
this option is available in Windows only. It lists storage device names and the corresponding
volumes, if any. When used twice it adds the "bus type" of the closest transport (e.g. a SATA disk
in a USB connected enclosure has bus type Usb). When used three times a SCSI adapter scan is
added. When used four times only a SCSI adapter scan is shown. See examples below and the "Win32
port" section in the README file.
NOTES
The reference document used for interpreting mode and VPD pages (and the INQUIRY standard response) is
T10/BSR INCITS 502 Revision 17 (SPC-5, 19 September 2017) found at http://www.t10.org . Obsolete and
reserved items in the standard INQUIRY response output are displayed in brackets. Recent drafts of other
T10 documents are also used: SBC-4 (disks), SSC-5 (tapes), SPL-5 (SAS transport) and SAT-4 (SCSI to ATA
Translation).
A mode page for which no abbreviation is known (e.g. a vendor specific mode page) can be listed in
hexadecimal by using the option combination '--page=PG --hex'.
Numbers input to sdparm (e.g. in the command line arguments) are assumed to be in decimal unless there is
a hexadecimal indicator. A hexadecimal indicator is either a leading '0x' or '0X' (i.e. the C language
convention) or a trailing 'h' or 'H' (i.e. the convention used at www.t10.org ). In the case of --page=
either a string or number is expected, so hex numbers like 'ch' (12) should be prefixed by a zero (e.g.
'0ch').
The SPC-4 draft (rev 2) says that devices that implement no distinction between current and saved pages
can return an error (ILLEGAL REQUEST, invalid field in cdb) if the SP bit (which corresponds to the
--save option) is _not_ set. In such cases the --save option needs to be given.
If the --save option is given but the existing mode page indicates (via its PS bit) that the page is not
saveable, then this utility generates an error message. That message suggests to try again without the
--save option.
Since the device identification VPD page (acronym_name "di") potentially contains a lot of diverse
designators, several associated acronyms are available. They are "di_lu" for designators associated with
the addressed logical unit, "di_port" for designators associated with the target port (which the command
arrived via) and "di_target" for designators associated with the target device. When "di" is used
designators are grouped by lu, then port and then target device. To see all designators decoded in the
order that they appear in the VPD page use "di_asis".
Only those VPD pages defined by t10.org are decoded by this utility. SPC-4 sets aside VPD pages codes
from 0xc0 to 0xff (inclusive) for vendor specific pages some of which are decoded in the sg_vpd utility.
To see all VPD pages supported by a DEVICE use 'sg_vpd --all'.
In the linux kernel 2.6 and 3 series any device node that understands a SCSI command set (e.g. SCSI disks
and CD/DVD drives) may be specified. More precisely the driver that "owns" the device node must support
the SG_IO ioctl. In the lk 2.4 series only SCSI generic (sg) device nodes support the SG_IO ioctl.
However in the lk 2.4 series other SCSI device nodes are mapped within this utility to their
corresponding sg device nodes. So if there is a SCSI disk at /dev/sda then 'sdparm /dev/sda' will work in
both the lk 2.4 series and later. However if there is an ATAPI cd/dvd drive at /dev/hdc then 'sdparm
/dev/hdc' will only work in the lk 2.6 series and later.
In the Linux 2.6 and 3 series, especially with ATA disks, using sdparm to stop (spin down) a disk may not
be sufficient and other mechanisms will start the disk again some time later. The user might additionally
mark the disk as "offline" with 'echo offline > /sys/block/sda/device/state' where sda is the block name
of the disk. To restart the disk "offline" can be replaced with "running".
PARAMETERS
In their simplest form the --clear=, --get= and --set= options (or their short forms) take an
acronym_name such as "WCE". In the case of '--get=WCE' the value of "Writeback Cache Enable" in the
caching mode page will be fetched. In the case of '--set=WCE' that bit will be set (to one). In the case
of '--clear=WCE' that bit will be cleared (to zero). When an acronym_name is given then the mode page is
imputed from that acronym_name (e.g. WCE is in the caching mode page).
Instead of an acronym_name a field within a mode page can be described numerically with a
<start_byte>:<start_bit>:<num_bits> tuple. These are the <start_byte> (origin 0) within the mode page, a
<start_bit> (0 to 7 inclusive) and <num_bits> (1 to 64 inclusive). For example, the low level
representation of the RCD bit (the "Read Cache Disable bit in the caching mode page) is "2:0:1". The
<start_byte> can optionally be given in hex (e.g. '--set=0x2:0:1' or '--set=2h:0:1'). With this form the
--page= option is required to establish which mode page is to be used.
Either form can optionally be followed by "=<val>". By default <val> is decimal but can be given in hex
in the normal fashion. Here are some examples: '--set=2h:0:1=1h' and '-s MRIE=0x3'. When the acronym_name
or numeric form following --clear= is not given an explicit '=<val>' then the value defaults to zero.
When the acronym_name or numeric form following --set= is not given an explicit '=<val>' then the value
defaults to "all ones" (i.e. as many as <num_bits> permits). For example '--clear=WCE' and
'--clear=WCE=0' have the same meaning: clear Writeback Cache Enable or, put more simply: turn off the
writeback cache.
Multiple fields within the same mode page can be changed by giving a comma separated list of
acronym_names and/or the numerical form. For example: '--set=TEST,MRIE=6'.
Some mode page have multiple descriptors. They typically have a fixed header section at the start of the
mode page that includes a field containing the number of descriptors that follow. Following the header is
a variable number of descriptors. An example is the SAS Phy Control and Discover mode page. An
acronym_name may include a trailing '.<num>' where "<num>" is a descriptor number (origin 0). For example
'-t sas -g PHID.0' and '-t sas -g PHID' will yield the phy identifier of the first descriptor of the
above mode page; '-t sas -g PHID.1' will yield the phy identifier of the second descriptor.
ENUMERATE
The --enumerate option essentially dumps out static information held by this utility. A list of
--enumerate variants and their actions follows. For brevity subsequent examples of options are shown in
their shorter form.
--enumerate list generic mode page information
-e --all list generic mode page contents
(i.e. parameters)
-e --page=rw list contents of read write error
recovery mode page
-e --inquiry list VPD pages this utility can decode
-e --long list generic mode pages, transport
protocols, mode pages for each
supported transport protocol and
supported commands
-e -l --all additionally list the contents of
each mode page
-e --transport=fcp list mode pages for the fcp
transport protocol
-e -t fcp --all additionally list the contents of
each mode page
-e --vendor=sea list vendor specific mode pages for
"sea" (Seagate)
-e -M sea --all additionally list the contents of vendor
specific mode pages for "sea" (Seagate)
-e -p pcd -l list contents of SAS phy control and
discovery mode page plus (due to "-l")
some descfriptor format information
When known mode pages are listed (via the --enumerate option) each line starts with a two or three
letter abbreviation. This is followed by the page number (in hex prefixed by "0x") optionally followed by
a comma and the subpage number. Finally the descriptive name of the mode page (e.g. as found in SPC-4) is
output.
When known parameters (fields) of a mode page are listed, each line starts with an acronym (indented a
few spaces). This will match (or be an acronym for) the description for that field found in the (draft)
standards. Next are three numbers, separated by colons, surrounded by brackets. These are the start byte
(in hex, prefixed by "0x") of the beginning of the field within the mode page; the starting bit (0
through 7 inclusive) and then the number of bits. The descriptive name of the parameter (field) is then
given. If appropriate the descriptive name includes units (e.g. "(ms)" means the units are milliseconds).
Adding the '-ll' option will list information about possible field values for selected mode page
parameters.
Mode parameters for which the num_bits is greater than 1 can be viewed as unsigned integers. Often 16 and
32 bit fields are set to 0xffff and 0xffffffff respectively (all ones) which usually has a special
meaning (see drafts). This utility outputs such values as "-1" to save space (rather than their unsigned
integer equivalents). "-1" can also be given as the value to a mode page field acronym (e.g.
'--set=INTT=-1' sets the interval timer field in the Informational Exceptions control mode page to
0xffffffff).
TRANSPORTS
SCSI transport protocols are a relatively specialized area that can be safely ignored by the majority of
users.
Some transport protocols have protocol specific mode pages. These are usually the disconnect-reconnect
(0x2), the protocol specific logical unit (0x18) and the protocol specific port (0x19) mode pages. In
some cases the latter mode page has several subpages. The most common transport protocol abbreviations
likely to be used are "fcp", "spi" and "sas".
Many of the field names are re-used in the same position so the acronym_name namespaces have been divided
between generic mode pages (i.e. when the --transport= option is _not_ given) and a namespace for each
transport protocol. A LUPID field from the protocol specific logical unit (0x18) mode page and the PPID
field from protocol specific port (0x19) mode page are included in the generic modes pages; this is so
the respective (transport) protocol identifiers can be seen. In most cases the user will know what the
"port" transport is (i.e. the same transport as the HBA in the computer) but the logical unit's transport
could be different.
VENDORS
SCSI leaves a lot of space for vendor specific information. Often this is described in product manuals.
The --vendor=VN (or -M=VN) option allows known vendor specific mode pages to be examined and/or modified
by acronym.
In this utility the syntax and semantics of vendor specific mode pages is very similar to those of
transport protocol specific mode pages. Both cannot be specified together. Vendor specific modes pages
can still be accessed numerically (as shown at the end of the EXAMPLES section).
COMMANDS
The command option sends a SCSI command to the DEVICE. If the command fails then this is reflected in the
non-zero exit status. To obtain more information about the error use the -v option.
capacity
sends a READ CAPACITY(10) command (valid for disks and cd/dvd media) by default. If successful
yields "blocks: " [the number of blocks], "block_length: " [typically either 512 or 2048] and
"capacity_mib: " [capacity in MibiBytes (1048576 byte units)].
If the number of blocks is too large to fit in the 4 byte field provided by READ CAPACITY(10) or, the
--long option is given, then the READ CAPACITY(16) command is sent. If the --long option is given, then
the extra fields found in the READ CAPACITY(16) response are output.
eject stops the medium and ejects it from the device. Note that ejection (by command or button) may be
prevented in which case the 'unlock' command may be useful in extreme cases. Typically only
appropriate for cd/dvd drives and disk drives with removable media. Objects if sent to another
peripheral device type (but objection can be overridden with '-f' option).
load loads the medium and starts it (i.e. spins it up). See 'eject' command for supported device types.
profile
lists the various formats that a CD/DVD/HD-DVD/BD drive supports. These are called "profiles" in
the MMC standard. The profiles are listed one per line. If media is in the drive then the profile
that matches the media (if any) has an "*" to the right of the line.
ready sends the "Test Unit Ready" SCSI command to the DEVICE. No error is reported if the device will
respond to data requests (e.g. READ) in a reasonable timescale. For example, if a disk is stopped
then it will report "not ready". All devices should respond to this command.
sense sends a REQUEST SENSE command. It reports a hardware threshold exceeded, warning or low power
condition if flagged. If a progress indication is present (e.g. during a format) then it will be
output as a percentage. Yields a process status of 0 if the command succeeds and the sense key is
0; else yields 1. The --quiet option can be used to lessen output, and --hex to output sense data
in hex.
speed=SPEED
permits the speed of a CD, DVD, HD_DVD or BD disc in a drive to be set (or at least influenced).
It has this format: --command=speed=SPEED where SPEED is in kilobytes per second. In this case a
kilobyte is 1000 bytes. The "times one" speed for a CD is 176.4 kB/s, for a DVD is 1350 kB/s and
for both HD-DVD and BD it is 4500 kB/s. If SPEED is zero then the drive is set to the speed that
it considers gives optimal performance. This command sends a SET STREAMING multi-media command
(MMC) to the drive. The EXACT bit is clear so the drive will round the given SPEED as necessary.
The command is designed to control read speed; setting write speed should be left to "burning"
programs.
start starts the medium (i.e. spins it up). Harmless if medium has already been started. See 'eject'
command for supported device types. If the DEVICE is an ATA disk in Linux the '--readonly' option
may be required.
stop stops the medium (i.e. spins it down). Harmless if medium has already been stopped. See 'eject'
command for supported device types. If the DEVICE is an ATA disk in Linux the '--readonly' option
may be required. See the NOTES section above.
sync sends a SYNCHRONIZE CACHE command. The device should flush any data held in its (volatile) buffers
to the media.
unlock tells a device to allow medium removal. It uses the SCSI "prevent allow medium removal" command.
This is desperation stuff, possibly overriding a prevention applied by the OS on a mounted file
system. The "eject" utility (from the "eject" package) is more graceful and should be tried first.
This command is only appropriate for devices with removable media.
For loading and ejecting tapes the mt utility should be used (i.e. not these commands). The 'ready'
command is valid for tape devices.
EXAMPLES
To list the common (generic) mode parameters of a disk:
sdparm /dev/sda
To list the designators within the device identification VPD page of a disk:
sdparm --inquiry /dev/sda
To see all parameters for the caching mode page:
sdparm --page=ca /dev/sda
To see all parameters for the caching mode page with parameter descriptions to the right:
sdparm --page=ca --long /dev/sda
To get the WCE values (current changeable default and saved) in hex:
sdparm -g WCE -H /dev/sda
0x01 0x00 0x01 0x01
To get the WCE current value in hex:
sdparm -g WCE=1 -H /dev/sda
0x01
To set the "Writeback Cache Enable" bit in the current values page:
sdparm --set=WCE /dev/sda
To set the "Writeback Cache Enable" bit in the current and saved values page:
sdparm --set=WCE --save /dev/sda
To set the "Writeback Cache Enable" and clear "Read Cache Disable":
sdparm --set=WCE --clear=RCD --save /dev/sda
The previous example can also by written as:
sdparm -s WCE=1,RCD=0 -S /dev/sda
To re-establish the manufacturer's defaults in the current and saved values of the caching mode page:
sdparm --page=ca --defaults --save /dev/sda
If an ATAPI cd/dvd drive is at /dev/hdc then its common (mode) parameters could be listed in the lk 2.6
and 3 series with:
sdparm /dev/hdc
If there is a DVD in the drive at /dev/hdc then it could be ejected in the lk 2.6 and 3 series with:
sdparm --command=eject /dev/hdc
If the ejection is being prevented by software then that can be overridden with:
sdparm --command=unlock /dev/hdc
One disk vendor has a "Performance Mode" bit (PM) in the vendor specific unit attention mode page
[0x0,0x0]. PM=0 is server mode (the default) while PM=1 is desktop mode. Desktop mode can be set (both
current and saved values) with:
sdparm --page=0 --set=2:7:1=1 --save /dev/sda
The resultant change can be viewed in hex with the --hex option as there are no acronyms for vendor
extensions yet. The PM bit is now covered by vendor specific mode pages and the above can also be
accomplished with:
sdparm --vendor=sea --set=PM --save /dev/sda
What follows are some examples from Windows using the '--wscan' option. The idea is to list the storage
device names on the system that might be invoked by other uses of sdparm.
# sdparm --wscan
PD0 [C] FUJITSU MHY2160BH 0000
PD1 [DF] WD 2500BEV External 1.05 WD-WXE90
CDROM0 [E] MATSHITA DVD/CDRW UJDA775 CB03
So 'sdparm -a CDROM0' and 'sdparm -a E' will show all the (known) mode page fields for the Matshita
DVD/CD drive. By using the '--wscan' option twice, the bus type (as seen by the OS) is added to the
output:
# sdparm -ww
PD0 [C] <Ata > FUJITSU MHY2160BH 0000
PD1 [DF] <Usb > WD 2500BEV External 1.05 WD-WXE90
CDROM0 [E] <Atapi> MATSHITA DVD/CDRW UJDA775 CB03
And the pattern continues to add a SCSI adapter scan. This may be useful if there are specialized storage
related devices (e.g. a SES device in an enclosure) but does add much extra information in this case.
# sdparm -www
PD0 [C] <Ata > FUJITSU MHY2160BH 0000
PD1 [DF] <Usb > WD 2500BEV External 1.05 WD-WXE90
CDROM0 [E] <Atapi> MATSHITA DVD/CDRW UJDA775 CB03
SCSI0:0,0,0 claimed=1 pdt=0h FUJITSU MHY2160BH 0000
SCSI1:0,0,0 claimed=1 pdt=5h MATSHITA DVD/CDRW UJDA775 CB03
EXIT STATUS
To aid scripts that call sdparm, the exit status is set to indicate success (0) or failure (1 or more).
Note that some of the lower values correspond to the SCSI sense key values. The exit status values are:
0 success
1 syntax error. Either illegal command line options, options with bad arguments or a combination of
options that is not permitted.
2 the DEVICE reports that it is not ready for the operation requested. The device may be in the
process of becoming ready (e.g. spinning up but not at speed) so the utility may work after a
wait.
3 the DEVICE reports a medium or hardware error (or a blank check). For example an attempt to read a
corrupted block on a disk will yield this value.
5 the DEVICE reports an "illegal request" with an additional sense code other than "invalid
operation code". This is often a supported command with a field set requesting an unsupported
capability. For commands that require a "service action" field this value can indicate that the
command is not supported.
6 the DEVICE reports a "unit attention" condition. This usually indicates that something unrelated
to the requested command has occurred (e.g. a device reset) potentially before the current SCSI
command was sent. The requested command has not been executed by the device. Note that unit
attention conditions are usually only reported once by a device.
7 the DEVICE reports a "data protect" sense key. This implies some mechanism has blocked writes (or
possibly all access to the media).
9 the DEVICE reports an illegal request with an additional sense code of "invalid operation code"
which means that it doesn't support the requested command.
10 the DEVICE reports a "copy aborted". This implies another command or device problem has stopped a
copy operation. The EXTENDED COPY family of commands (including WRITE USING TOKEN) may return this
sense key.
11 the DEVICE reports an aborted command. In some cases aborted commands can be retried immediately
(e.g. if the transport aborted the command due to congestion).
14 the DEVICE reports a miscompare sense key. VERIFY and COMPARE AND WRITE commands may report this.
15 the utility is unable to open, close or use the given DEVICE. The given file name could be
incorrect or there may be permission problems. Adding the -v option may give more information.
20 the DEVICE reports it has a check condition but "no sense". Some polling commands (e.g. REQUEST
SENSE) can react this way. It is unlikely that this value will occur as an exit status.
21 the DEVICE reports a "recovered error". The requested command was successful. Most likely a
utility will report a recovered error to stderr and continue, probably leaving the utility with an
exit status of 0 .
22 the DEVICE reports that the current command or its parameters imply a logical block address (LBA)
that is out of range.
24 the DEVICE reports a SCSI status of "reservation conflict". This means access to the DEVICE with
the current command has been blocked because another machine (HBA or SCSI "initiator") holds a
reservation on this DEVICE. On modern SCSI systems this is related to the use of the PERSISTENT
RESERVATION family of commands.
25 the DEVICE reports a SCSI status of "condition met". Currently only the PRE-FETCH command (see
SBC-4) yields this status.
26 the DEVICE reports a SCSI status of "busy". SAM-5 defines this status as the logical unit is
temporarily unable to process a command. It is recommended to re-issue the command.
27 the DEVICE reports a SCSI status of "task set full".
28 the DEVICE reports a SCSI status of "ACA active". ACA is "auto contingent allegiance" and is
seldom used.
29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "This status shall be returned if
a command is aborted by a command or task management function on another I_T nexus and the Control
mode page TAS bit is set to one".
33 the command sent to DEVICE has timed out. This occurs in Linux only; in other ports a command
timeout will appear as a transport (or OS) error.
40 the command sent to DEVICE has received an "aborted command" sense key with an additional sense
code of 0x10. This value is related to problems with protection information (PI or DIF). For
example this error may occur when reading a block on a drive that has never been written (or is
unmapped) if that drive was formatted with type 1, 2 or 3 protection.
48 this is an internal message indicating a NVMe status field (SF) is other than zero after a command
has been executed (i.e. something went wrong). Work in this area is currently experimental.
49 low level driver reports a response's residual count (i.e. number of bytes actually received by
HBA is 'requested_bytes - residual_count') that is too high. So no useful processing can be done
with that response.
50 + <os_error_number>
OS system calls that fail often return a small integer number to help indicate what the error is.
For example in Unix the inability of a system call to allocate memory returns (in 'errno') ENOMEM
which often is associated with the integer 12. So 62 (i.e. '50 + 12') may be returned by a utility
in this case.
97 the response to a SCSI command failed sanity checks.
98 the DEVICE reports it has a check condition but the error doesn't fit into any of the above
categories.
99 any errors that can't be categorized into values 1 to 98 may yield this value. This includes
transport and operating system errors after the command has been sent to the device.
126 the utility was found but could not be executed. That might occur if the executable does not have
execute permissions.
127 This is the exit status for utility not found. That might occur when a script calls a utility in
this package but the PATH environment variable has not been properly set up, so the script cannot
find the executable.
128 + <signum>
If a signal kills a utility then the exit status is 128 plus the signal number. For example if a
segmentation fault occurs then a utility is typically killed by SIGSEGV which according to 'man 7
signal' has an associated signal number of 11; so the exit status will be 139 .
255 the utility tried to yield an exit status of 255 or larger. That should not happen; given here for
completeness.
Most of the error conditions reported above will be repeatable (an example of one that is not is "unit
attention") so the utility can be run again with the -v option (or several) to obtain more information.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2005-2021 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE.
WEB SITE
There is a web page discussing this package at https://sg.danny.cz/sg/sdparm.html .
SEE ALSO
hdparm(hdparm), sg_modes, sg_wr_mode, sginfo, sg_inq, sg_vpd(all in sg3_utils),
smartmontools(smartmontools.sourceforge.net), mt, eject(eject),