NAME

       sd_bus_send, sd_bus_send_to, sd_bus_message_send - Queue a D-Bus message for transfer

SYNOPSIS

       #include <systemd/sd-bus.h>

       int sd_bus_send(sd_bus *bus, sd_bus_message *m, uint64_t *cookie);

       int sd_bus_send_to(sd_bus *bus, sd_bus_message *m, const char *destination, uint64_t *cookie);

       int sd_bus_message_send(sd_bus_message *m);

DESCRIPTION

       sd_bus_send() queues the bus message object m for transfer. If bus is NULL, the bus that m is attached to
       is used.  bus only needs to be set when the message is sent to a different bus than the one it's attached
       to, for example when forwarding messages. If the output parameter cookie is not NULL, it is set to the
       message identifier. This value can later be used to match incoming replies to their corresponding
       messages. If cookie is set to NULL and the message is not sealed, sd_bus_send() assumes the message m
       doesn't expect a reply and adds the necessary headers to indicate this.

       Note that in most scenarios, sd_bus_send() should not be called directly. Instead, use higher level
       functions such as sd_bus_call_method(3) and sd_bus_reply_method_return(3) which call sd_bus_send()
       internally.

       sd_bus_send_to() is a shorthand for sending a message to a specific destination. It's main use case is to
       simplify sending unicast signal messages (signals that only have a single receiver). It's behavior is
       similar to calling sd_bus_message_set_destination(3) followed by calling sd_bus_send().

       sd_bus_send()/sd_bus_send_to() will write the message directly to the underlying transport (e.g. kernel
       socket buffer) if possible. If the connection is not set up fully yet the message is queued locally. If
       the transport buffers are congested any unwritten message data is queued locally, too. If the connection
       has been closed or is currently being closed the call fails.  sd_bus_process(3) should be invoked to
       write out any queued message data to the transport.

       sd_bus_message_send() is the same as sd_bus_send() but without the first and last argument.
       sd_bus_message_send(m) is equivalent to sd_bus_send(sd_bus_message_get_bus(m), m, NULL).

RETURN VALUE

       On success, these functions return a non-negative integer. On failure, they return a negative errno-style
       error code.

   Errors
       Returned errors may indicate the following problems:

       -EINVAL
           The input parameter m is NULL.

           Added in version 246.

       -EOPNOTSUPP
           The bus connection does not support sending file descriptors.

           Added in version 246.

       -ECHILD
           The bus connection was allocated in a parent process and is being reused in a child process after
           fork().

           Added in version 246.

       -ENOBUFS
           The bus connection's write queue is full.

           Added in version 246.

       -ENOTCONN
           The input parameter bus is NULL or the bus is not connected.

           Added in version 246.

       -ECONNRESET
           The bus connection was closed while waiting for the response.

           Added in version 246.

       -ENOMEM
           Memory allocation failed.

           Added in version 246.

NOTES

       Functions described here are available as a shared library, which can be compiled against and linked to
       with the libsystemd pkg-config(1) file.

       The code described here uses getenv(3), which is declared to be not multi-thread-safe. This means that
       the code calling the functions described here must not call setenv(3) from a parallel thread. It is
       recommended to only do calls to setenv() from an early phase of the program when no other threads have
       been started.

HISTORY

       sd_bus_send() and sd_bus_send_to() were added in version 246.

SEE ALSO

       systemd(1), sd-bus(3), sd_bus_call_method(3), sd_bus_message_set_destination(3),
       sd_bus_reply_method_return(3), sd_bus_process(3)