NAME

       gpsmon - real-time GPS packet monitor and control utility

SYNOPSIS

       gpsmon [OPTIONS} [server[:port[:device]]]

       gpsmon -h

       gpsmon -V

DESCRIPTION

       gpsmon is a monitor that watches packets coming from a GPS and displays them along with
       diagnostic information. It supports commands that can be used to tweak GPS settings in
       various ways; some are device-independent, some vary with the GPS chipset type. It will
       behave sanely, just dumping packets, when connected to a GPS type it knows nothing about.

       gpsmon differs from a navigation client in that it mostly dumps raw data from the GPS,
       with only enough data-massaging to allow checks against expected output. It does not use
       gpsd to decode packets. There are many raw data types that gpsd knows about that gpsmon
       does not. In particular, this tool does not do any interpolation or modeling to derive
       climb/sink or error estimates. Nor does it discard altitude reports when the fix quality
       is too low.

       The casual gpsd user will be better served by the cgps clients which display navigation
       data the same way for all GNSS receivers that gpsd supports. Such as cgps and xgps.

       Unlike gpsd, gpsmon never writes control or probe strings to the device unless you
       explicitly tell it to. Thus, while it will auto-sync to binary packet types, it won’t
       automatically recognize a device shipping an extended NMEA protocol as anything other than
       a plain NMEA device. Use the -t option or the t to work around this.

       gpsmon is a designed to run in a terminal emulator with a minimum 25x80 size; the non-GUI
       interface is a design choice made to accommodate users operating in constrained
       environments and over telnet or ssh connections. If run in a larger window, the size of
       the packet-log window will be increased to fit.

       After startup (without -a or --nocurses), the top part of the screen reports the contents
       of several especially interesting packet types. The "PPS" field, if nonempty, is the delta
       between the last 1PPS top of second and the system clock at that time.

       The bottom half of the screen is a scrolling hex dump of all packets the GPS is issuing.
       If the packet type is textual, any trailing CR/LF is omitted. Dump lines beginning ">>>"
       represent control packets sent to the GPS. Lines consisting of "PPS" surrounded by dashes,
       if present, indicate 1PPS and the start of the reporting cycle.

       Unlike gpsd, gpsmon when run in direct mode does not do its own device probing. Thus, in
       particular, if you point it at a GPS with a native binary mode that happens to be emitting
       NMEA, it won’t identify the actual type unless the device emits a recognizable NMEA
       trigger sentence. The -t, --type option may help you.

       gpsmon does not require root privileges, except maybe to access the serial port in direct
       mode. It will run fine as root.

OPTIONS

       -?, -h, --help
           Print a usage message and exit.

       -a, --nocurses
           Enables a special debugging mode that does not use screen painting. Packets are dumped
           normally, any character typed suspends packet dumping and brings up a command prompt.
           This feature will mainly be of interest to GPSD developers.

       -d LVL, --debug LVL
           Enable packet-getter debugging output and is probably only useful to developers of the
           GPSD code. Consult the packet-getter source code for relevant values.

       -l FILE, --logfile FILE
           Set up logging to a specified file (FILE) to start immediately on device open. This
           may be useful is, for example, you want to capture the startup message from a device
           that displays firmware version information there.

       -L, --list
           Lists a table showing which GPS device types this gpsmon has built-in support for, and
           which generic commands can be applied to which GPS types, and then exits. Note that
           this does not list type-specific commands associated with individual GPS types.

       -n, --nmea
           Force gpsmon to request NMEA0183 packets instead of the raw data stream from gpsd.

       -t TYPE, --type TYPE
           Set a fallback type (TYPE). Give it a string that is a distinguishing prefix of
           exactly one driver type name; this will be used for mode, speed, and rate switching if
           the driver selected by the packet type lacks those capabilities. Most useful when the
           packet type is NMEA but the device is known to have a binary mode, such as SiRF
           binary.

ARGUMENTS

       This program may be run in either of two modes, as a client for the gpsd daemon (and its
       associated control socket) or directly connected to a specified serial device.

       By default, clients collect data from the local gpsd daemon running on localhost, using
       the default GPSD port 2947. The optional argument to any client may override this
       behavior: [server[:port[:device]]]

       For further explanation, and examples, see the ARGUMENTS section in the gps(1) man page

       If instead the argument contains slashes but no colons will it be treated as a serial
       device for direct connection. In direct-connect mode gpsmon will hunt for a correct baud
       rate and lock on to it automatically.

COMMANDS

       The following device-independent commands are available while gpsmon is running:

       i
           (Direct mode only.) Enable/disable subtype probing and reinitialize the driver. In
           normal operation, gpsmon does not send configuration strings to the device (except for
           wakeup strings needed to get it to send data, if any). The command 'i1' causes it to
           send the same sequence of subtype probes that gpsd would. The command 'i0' turns off
           probing; 'i' alone toggles the bit. In either case, the current driver is re-selected;
           if the probe bit is enabled, probes will begin to be issued immediately.

       Note that enabling probing might flip the device into another mode; in particular, it will
       flip a SiRF chip into binary mode as if you had used the "n" command. This is due to a
       limitation in the SiRF firmware that we can’t fix.

       This command will generally do nothing after the first time you use it, because the device
       type will already have been discovered.

       c
           (Direct mode only.) Change cycle time. Follow it with a number interpreted as a cycle
           time in seconds. Most devices have a fixed cycle time of 1 second, so this command may
           fail with a message.

       l
           Toggle packet logging. If packet logging is on, it will be turned off and the log
           closed. If it is off, logging to the filename following the l will be enabled. Differs
           from simply capturing the data from the GPS device in that only whole packets are
           logged. The logfile is opened for append, so you can log more than one portion of the
           packet stream and they will be stitched together correctly.

       n
           (Direct mode only.) With an argument of 0, switch device to NMEA mode at current
           speed; with an argument of 1, change to binary (native) mode. With no argument, toggle
           the setting. Will show an error if the device doesn’t have such modes.

       After you switch a dual-protocol GPS to NMEA mode with this command, it retains the
       information about the original type and its control capabilities. That is why the device
       type listed before the prompt doesn’t change.

       q
           Quit gpsmon. Control-C, or whatever your current interrupt character is, works as
           well.

       s
           (Direct mode only.) Change baud rate. Follow it with a number interpreted as bits per
           second, for example "s9600". The speed number may optionally be followed by a colon
           and a wordlength-parity-stopbits specification in the traditional style, e.g 8N1 (the
           default), 7E1, etc. Some devices don’t support serial modes other than their default,
           so this command may fail with a message.

           Note
           Use this command with caution. On USB and Bluetooth GPSs it is also possible for
           serial mode setting to fail either because the serial adaptor chip does not support
           non-8N1 modes or because the device firmware does not properly synchronize the serial
           adaptor chip with the UART on the GPS chipset when the speed changes. These failures
           can hang your device, possibly requiring a GPS power cycle or (in extreme cases)
           physically disconnecting the NVRAM backup battery.

       t
           (Direct mode only.) Force a switch of monitoring type. Follow it with a string that is
           unique to the name of a gpsd driver with gpsmon support; gpsmon will switch to using
           that driver and display code. Will show an error message if there is no matching gpsd
           driver, or multiple matches, or the unique match has no display support in gpsmon.

       x
           (Direct mode only.) Send hex payload to device. Following the command letter you may
           type hex digit pairs; end with a newline. These will become the payload of a control
           packet shipped to the device. The packet will be wrapped with headers, trailers, and
           checksum appropriate for the current driver type. The first one or two bytes of the
           payload may be specially interpreted, see the description of the -x of gpsctl 1 .

       X
           (Direct mode only.) Send raw hex bytes to device. Following the command letter you may
           type hex digit pairs; end with a newline. These will be shipped to the device.

       Ctrl-S
           Freeze display, suspend scrolling in debug window.

       Ctrl-Q
           Unfreeze display, resume normal operation.

   NMEA support
       (These remarks apply to not just generic NMEA devices but all extended NMEA devices for
       which gpsmon presently has support.)

       All fields are raw data from the GPS except (a) the "Cooked PVT" window near top of
       screen, provided as a check and (b) the "PPS offset" field.

       There are no device-specific commands. Which generic commands are available may vary by
       type: examine the output of gpsmon -l to learn more.

   SiRF support
       Most information is raw from the GPS. Underlined fields are derived by translation from
       ECEF coordinates or application of leap-second and local time-zone offsets. 1PPS is the
       clock lag as usual.

       The following commands are supported for SiRF GPSes only:

       A
           (Direct mode only.) Toggle reporting of 50BPS subframe data.

       M
           (Direct mode only.) Set (M1) or clear (M0) static navigation. The SiRF documentation
           says "Static navigation is a position filter designed to be used with motor vehicles.
           When the vehicle’s velocity falls below a threshold, the position and heading are
           frozen, and velocity is set to zero. This condition will continue until the computed
           velocity rises above 1.2 times the threshold or until the computed position is at
           least a set distance from the frozen place. The threshold velocity and set distance
           may vary with software versions."

       Non-static mode is designed for use with road navigation software, which often snaps the
       reported position to the nearest road within some uncertainty radius. You probably want to
       turn static navigation off for pedestrian use, as it is likely to report speed zero and
       position changing in large jumps.

       P
           (Direct mode only.) Toggle navigation-parameter display mode. Toggles between normal
           display and one that shows selected navigation parameters from MID 19, including the
           Static Navigation bit toggled by the 'M' command.

       To interpret what you see, you will need a copy of the SiRF Binary Protocol Reference
       Manual.

   u-blox support
       Most information is raw from the GPS. Underlined fields are derived by translation from
       ECEF coordinates. 1PPS is the clock lag as usual. There are no per-type special commands.

BUGS AND LIMITATIONS

       The PPS Offset field will never be updated when running in client mode, even if you can
       see PPS events in the packet window. This limitation may be fixed in a future release.

RETURN VALUES

       0
           on success.

       1
           on failure

SEE ALSO

       gpsd(8), cgps, (1)gpsctl(1), gps(1), *xgps(1)

RESOURCES

       Project web site: https://gpsd.io/

COPYING

       This file is Copyright 2013 by the GPSD project
       SPDX-License-Identifier: BSD-2-clause

AUTHOR

       Eric S. Raymond