Ubuntu Manpage: wimoptimize - Optimize a WIM archive

Provided by: wimtools_1.14.4-1.1build2_amd64

NAME

       wimoptimize - Optimize a WIM archive

SYNOPSIS

       wimoptimize WIMFILE [OPTION...]

DESCRIPTION

       wimoptimize,  or  equivalently wimlib-imagex optimize, rebuilds the standalone WIM archive
       WIMFILE.  The new WIM is written to a temporary file, and it is renamed  to  the  original
       file  when  it's  ready.   This  will remove any holes that have been left in the WIM as a
       result of appending or deleting files or images, so the new WIM may be  smaller  than  the
       old WIM.

       By  default,  wimoptimize  will reuse (not recompress) compressed data and will not change
       the solid or pipable status of the WIM.  However, it can also perform recompression and/or
       convert  between  solid,  non-solid,  pipable,  and  non-pipable WIMs; see the options and
       examples below.

OPTIONS

--check
Before optimizing the WIM, verify its integrity if it contains extra integrity
information. Also include extra integrity information in the optimized WIM, even if
it was not present before.

--nocheck
Do not include extra integrity information in the optimized WIM, even if it was
present before.

--include-integrity
Include extra integrity information in the optimized WIM, i.e. like --check but
don't also verify the WIM beforehand.

--recompress
Recompress all data in the WIM while optimizing it. This will significantly
increase the time needed to optimize the WIM, but it may result in a better
compression ratio if wimlib can do a better job than the program that created the
WIM --- which is likely the case if the WIM was Microsoft-created, as wimlib's
compressors are slightly stronger.

--compress=TYPE[:LEVEL]
Recompress the WIM using the specified compression type, and optionally the
specified compression level for that compression type. This implies --recompress.
See the documentation for this option to wimcapture(1) for more details.

--chunk-size=SIZE
Set the WIM compression chunk size to SIZE. See the documentation for this option
to wimcapture(1) for more details.

--solid
Create a "solid" archive that compresses multiple files together. This usually
results in a significantly better compression ratio but has disadvantages such as
reduced compatibility. See the documentation for this option to wimcapture(1) for
more details.

--solid-compress=TYPE[:LEVEL]
Like --compress, but set the compression type used in solid resources. See the
documentation for this option to wimcapture(1) for more details.

--solid-chunk-size=SIZE
Like --chunk-size, but set the chunk size used in solid resources. See the
documentation for this option to wimcapture(1) for more details.

--threads=NUM_THREADS
Number of threads to use for compressing data. Default: autodetect (number of
processors).

--pipable
Rebuild the WIM so that it can be applied fully sequentially, including from a pipe.
See wimcapture(1) for more details about creating pipable WIMs. By default, when
neither --pipable or --not-pipable is specified, the optimized WIM will be pipable
if and only if it was pipable before.

--not-pipable
Rebuild the WIM in the non-pipable format.

--unsafe-compact
Compact the WIM in-place, without using a temporary file. Existing resources are
shifted down to fill holes and new resources are appended as needed. The WIM is
truncated to its final size, which may shrink the on-disk file. This is more
efficient than a full rebuild, but it is only supported when no recompression is
being done. More importantly, AN UNSAFE COMPACTION OPERATION CANNOT BE SAFELY
INTERRUPTED! If the operation is interrupted, then the WIM will be corrupted, and
it may be impossible (or at least very difficult) to recover any data from it.
Users of this option are expected to know what they are doing and assume
responsibility for any data corruption that may result.

NOTES

       wimoptimize does not support split WIMs or delta WIMs.  For  such  files,  consider  using
       wimexport(1) instead.  Note that wimoptimize is roughly equivalent to:

              wimexport WIMFILE all tmp.wim && mv tmp.wim WIMFILE

EXAMPLES