Ubuntu Manpage: random, urandom - kernel random number source devices

NAME

       random, urandom - kernel random number source devices

SYNOPSIS

       #include <linux/random.h>

       int ioctl(fd, RNDrequest, param);

DESCRIPTION

The character special files /dev/random and /dev/urandom (present since Linux 1.3.30)
provide an interface to the kernel's random number generator. The file /dev/random has
major device number 1 and minor device number 8. The file /dev/urandom has major device
number 1 and minor device number 9.

The random number generator gathers environmental noise from device drivers and other
sources into an entropy pool. The generator also keeps an estimate of the number of bits
of noise in the entropy pool. From this entropy pool, random numbers are created.

Linux 3.17 and later provides the simpler and safer getrandom(2) interface which requires
no special files; see the getrandom(2) manual page for details.

When read, the /dev/urandom device returns random bytes using a pseudorandom number
generator seeded from the entropy pool. Reads from this device do not block (i.e., the
CPU is not yielded), but can incur an appreciable delay when requesting large amounts of
data.

When read during early boot time, /dev/urandom may return data prior to the entropy pool
being initialized. If this is of concern in your application, use getrandom(2) or
/dev/random instead.

The /dev/random device is a legacy interface which dates back to a time where the
cryptographic primitives used in the implementation of /dev/urandom were not widely
trusted. It will return random bytes only within the estimated number of bits of fresh
noise in the entropy pool, blocking if necessary. /dev/random is suitable for
applications that need high quality randomness, and can afford indeterminate delays.

When the entropy pool is empty, reads from /dev/random will block until additional
environmental noise is gathered. Since Linux 5.6, the O_NONBLOCK flag is ignored as
/dev/random will no longer block except during early boot process. In earlier versions,
if open(2) is called for /dev/random with the O_NONBLOCK flag, a subsequent read(2) will
not block if the requested number of bytes is not available. Instead, the available bytes
are returned. If no byte is available, read(2) will return -1 and errno will be set to
EAGAIN.

The O_NONBLOCK flag has no effect when opening /dev/urandom. When calling read(2) for the
device /dev/urandom, reads of up to 256 bytes will return as many bytes as are requested
and will not be interrupted by a signal handler. Reads with a buffer over this limit may
return less than the requested number of bytes or fail with the error EINTR, if
interrupted by a signal handler.

Since Linux 3.16, a read(2) from /dev/urandom will return at most 32 MB. A read(2) from
/dev/random will return at most 512 bytes (340 bytes before Linux 2.6.12).

Writing to /dev/random or /dev/urandom will update the entropy pool with the data written,
but this will not result in a higher entropy count. This means that it will impact the
contents read from both files, but it will not make reads from /dev/random faster.

Usage
The /dev/random interface is considered a legacy interface, and /dev/urandom is preferred
and sufficient in all use cases, with the exception of applications which require
randomness during early boot time; for these applications, getrandom(2) must be used
instead, because it will block until the entropy pool is initialized.

If a seed file is saved across reboots as recommended below, the output is
cryptographically secure against attackers without local root access as soon as it is
reloaded in the boot sequence, and perfectly adequate for network encryption session keys.
(All major Linux distributions have saved the seed file across reboots since 2000 at
least.) Since reads from /dev/random may block, users will usually want to open it in
nonblocking mode (or perform a read with timeout), and provide some sort of user
notification if the desired entropy is not immediately available.

Configuration
If your system does not have /dev/random and /dev/urandom created already, they can be
created with the following commands:

mknod -m 666 /dev/random c 1 8
mknod -m 666 /dev/urandom c 1 9
chown root:root /dev/random /dev/urandom

When a Linux system starts up without much operator interaction, the entropy pool may be
in a fairly predictable state. This reduces the actual amount of noise in the entropy
pool below the estimate. In order to counteract this effect, it helps to carry entropy
pool information across shut-downs and start-ups. To do this, add the lines to an
appropriate script which is run during the Linux system start-up sequence:

echo "Initializing random number generator..."
random_seed=/var/run/random-seed
# Carry a random seed from start-up to start-up
# Load and then save the whole entropy pool
if [ -f $random_seed ]; then
cat $random_seed >/dev/urandom
else
touch $random_seed
fi
chmod 600 $random_seed
poolfile=/proc/sys/kernel/random/poolsize
[ -r $poolfile ] && bits=$(cat $poolfile) || bits=4096
bytes=$(expr $bits / 8)
dd if=/dev/urandom of=$random_seed count=1 bs=$bytes

Also, add the following lines in an appropriate script which is run during the Linux
system shutdown:

# Carry a random seed from shut-down to start-up
# Save the whole entropy pool
echo "Saving random seed..."
random_seed=/var/run/random-seed
touch $random_seed
chmod 600 $random_seed
poolfile=/proc/sys/kernel/random/poolsize
[ -r $poolfile ] && bits=$(cat $poolfile) || bits=4096
bytes=$(expr $bits / 8)
dd if=/dev/urandom of=$random_seed count=1 bs=$bytes

In the above examples, we assume Linux 2.6.0 or later, where
/proc/sys/kernel/random/poolsize returns the size of the entropy pool in bits (see below).

/proc interfaces
The files in the directory /proc/sys/kernel/random (present since Linux 2.3.16) provide
additional information about the /dev/random device:

entropy_avail
This read-only file gives the available entropy, in bits. This will be a number in
the range 0 to 4096.

poolsize
This file gives the size of the entropy pool. The semantics of this file vary
across kernel versions:

Linux 2.4:
This file gives the size of the entropy pool in bytes. Normally, this file
will have the value 512, but it is writable, and can be changed to any value
for which an algorithm is available. The choices are 32, 64, 128, 256, 512,
1024, or 2048.

Linux 2.6 and later:
This file is read-only, and gives the size of the entropy pool in bits. It
contains the value 4096.

read_wakeup_threshold
This file contains the number of bits of entropy required for waking up processes
that sleep waiting for entropy from /dev/random. The default is 64.

write_wakeup_threshold
This file contains the number of bits of entropy below which we wake up processes
that do a select(2) or poll(2) for write access to /dev/random. These values can
be changed by writing to the files.

uuid and boot_id
These read-only files contain random strings like
6fd5a44b-35f4-4ad4-a9b9-6b9be13e1fe9. The former is generated afresh for each
read, the latter was generated once.

ioctl(2) interface
The following ioctl(2) requests are defined on file descriptors connected to either
/dev/random or /dev/urandom. All requests performed will interact with the input entropy
pool impacting both /dev/random and /dev/urandom. The CAP_SYS_ADMIN capability is
required for all requests except RNDGETENTCNT.

RNDGETENTCNT
Retrieve the entropy count of the input pool, the contents will be the same as the
entropy_avail file under proc. The result will be stored in the int pointed to by
the argument.

RNDADDTOENTCNT
Increment or decrement the entropy count of the input pool by the value pointed to
by the argument.

RNDGETPOOL
Removed in Linux 2.6.9.

RNDADDENTROPY
Add some additional entropy to the input pool, incrementing the entropy count.
This differs from writing to /dev/random or /dev/urandom, which only adds some data
but does not increment the entropy count. The following structure is used:

struct rand_pool_info {
int entropy_count;
int buf_size;
__u32 buf[0];
};

Here entropy_count is the value added to (or subtracted from) the entropy count,
and buf is the buffer of size buf_size which gets added to the entropy pool.

RNDZAPENTCNT
RNDCLEARPOOL
Zero the entropy count of all pools and add some system data (such as wall clock)
to the pools.

FILES

       /dev/random
       /dev/urandom

NOTES

       For  an  overview  and  comparison  of  the  various interfaces that can be used to obtain
       randomness, see random(7).

BUGS