NAME

       ocf_heartbeat_ethmonitor - Monitors network interfaces

SYNOPSIS

       ethmonitor [start | stop | status | monitor | meta-data | validate-all]

DESCRIPTION

       Monitor the vitality of a local network interface.

       You may set up this RA as a clone resource to monitor the network interfaces on different
       nodes, with the same interface name. This is not related to the IP address or the network
       on which a interface is configured. You may use this RA to move resources away from a
       node, which has a faulty interface or prevent moving resources to such a node. This gives
       you independent control of the resources, without involving cluster intercommunication.
       But it requires your nodes to have more than one network interface.

       The resource configuration requires a monitor operation, because the monitor does the main
       part of the work. In addition to the resource configuration, you need to configure some
       location constraints, based on a CIB attribute value. The name of the attribute value is
       configured in the 'name' option of this RA.

       Example constraint configuration using crmsh location loc_connected_node my_resource_grp
       rule ="rule_loc_connected_node" -INF: ethmonitor eq 0

       Example constraint configuration using pcs. Only allow 'my_resource' to run on nodes where
       eth0 ethernet device is available. pcs constraint location my_resource rule
       score=-INFINITY ethmonitor-eth0 ne 1

       The ethmonitor works in 3 different modes to test the interface vitality. 1. call ip to
       see if the link status is up (if link is down -> error) 2. call ip and watch the RX
       counter (if packages come around in a certain time -> success) 3. call arping to check
       whether any of the IPs found in the local ARP cache answers an ARP REQUEST (one answer ->
       success) 4. return error

SUPPORTED PARAMETERS

       interface
           The name of the network interface which should be monitored (e.g. eth0).

           (unique, required, string, no default)

       name
           The name of the CIB attribute to set. This is the name to be used in the constraints.
           Defaults to "ethmonitor-'interface_name'".

           (unique, optional, string, no default)

       multiplier
           Multiplier for the value of the CIB attriobute specified in parameter name.

           (optional, integer, default 1)

       repeat_count
           Specify how often the interface will be monitored, before the status is set to failed.
           You need to set the timeout of the monitoring operation to at least repeat_count *
           repeat_interval

           (optional, integer, default 5)

       repeat_interval
           Specify how long to wait in seconds between the repeat_counts.

           (optional, integer, default 10)

       pktcnt_timeout
           Timeout for the RX packet counter. Stop listening for packet counter changes after the
           given number of seconds.

           (optional, integer, default 5)

       arping_count
           Number of ARP REQUEST packets to send for every IP. Usually one ARP REQUEST (arping)
           is send

           (optional, integer, default 1)

       arping_timeout
           Time in seconds to wait for ARP REQUESTs (all packets of arping_count). This is to
           limit the time for arp requests, to be able to send requests to more than one node,
           without running in the monitor operation timeout.

           (optional, integer, default 1)

       arping_cache_entries
           Maximum number of IPs from ARP cache list to check for ARP REQUEST (arping) answers.
           Newest entries are tried first.

           (optional, integer, default 5)

       infiniband_device
           For interfaces that are infiniband devices.

           (optional, string, no default)

       infiniband_port
           For infiniband devices, this is the port to monitor.

           (optional, integer, no default)

       link_status_only
           Only report success based on link status. Do not perform RX counter or arping related
           connectivity tests.

           (optional, boolean, default false)

SUPPORTED ACTIONS

       This resource agent supports the following actions (operations):

       start
           Starts the resource. Suggested minimum timeout: 60s.

       stop
           Stops the resource. Suggested minimum timeout: 20s.

       status
           Performs a status check. Suggested minimum timeout: 60s. Suggested interval: 10s.

       monitor
           Performs a detailed status check. Suggested minimum timeout: 60s. Suggested interval:
           10s.

       meta-data
           Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5s.

       validate-all
           Performs a validation of the resource configuration. Suggested minimum timeout: 20s.

EXAMPLE CRM SHELL

       The following is an example configuration for a ethmonitor resource using the crm(8)
       shell:

           primitive p_ethmonitor ocf:heartbeat:ethmonitor \
             params \
               interface=string \
             op monitor depth="0" timeout="60s" interval="10s"

EXAMPLE PCS

       The following is an example configuration for a ethmonitor resource using pcs(8)

           pcs resource create p_ethmonitor ocf:heartbeat:ethmonitor \
             interface=string \
             op monitor OCF_CHECK_LEVEL="0" timeout="60s" interval="10s"

SEE ALSO

       http://clusterlabs.org/

AUTHOR

       ClusterLabs contributors (see the resource agent source for information about individual
       authors)