Provided by: ppp_2.5.1-1+1_amd64 
NAME
chat - Automated conversational script with a modem
SYNOPSIS
chat [ options ] script
DESCRIPTION
The chat program defines a conversational exchange between the computer and the modem. Its
primary purpose is to establish the connection between the Point-to-Point Protocol Daemon
(pppd) and the remote's pppd process.
OPTIONS
-f <chat file>
Read the chat script from the chat file. The use of this option is mutually
exclusive with the chat script parameters. The user must have read access to the
file. Multiple lines are permitted in the file. Space or horizontal tab characters
should be used to separate the strings.
-t <timeout>
Set the timeout for the expected string to be received. If the string is not
received within the time limit then the reply string is not sent. An alternate
reply may be sent or the script will fail if there is no alternate reply string. A
failed script will cause the chat program to terminate with a non-zero error code.
You can also use the TIMEOUT string in order to specify the timeout.
-r <report file>
Set the file for output of the report strings. If you use the keyword REPORT, the
resulting strings are written to this file. If this option is not used and you
still use REPORT keywords, the stderr file is used for the report strings.
-e Start with the echo option turned on. Echoing may also be turned on or off at
specific points in the chat script by using the ECHO keyword. When echoing is
enabled, all output from the modem is echoed to stderr.
-E Enables environment variable substitution within chat scripts using the standard
$xxx syntax.
-v Request that the chat script be executed in a verbose mode. The chat program will
then log the execution state of the chat script as well as all text received from
the modem and the output strings sent to the modem. The default is to log through
the SYSLOG; the logging method may be altered with the -S and -s flags.
-V Request that the chat script be executed in a stderr verbose mode. The chat program
will then log all text received from the modem and the output strings sent to the
modem to the stderr device. This device is usually the local console at the station
running the chat or pppd program.
-s Use stderr. All log messages from '-v' and all error messages will be sent to
stderr.
-S Do not use the SYSLOG. By default, error messages are sent to the SYSLOG. The use
of -S will prevent both log messages from '-v' and error messages from being sent
to the SYSLOG.
-T <phone number>
Pass in an arbitrary string, usually a phone number, that will be substituted for
the \T substitution metacharacter in a send string.
-U <phone number 2>
Pass in a second string, usually a phone number, that will be substituted for the
\U substitution metacharacter in a send string. This is useful when dialing an
ISDN terminal adapter that requires two numbers.
script If the script is not specified in a file with the -f option then the script is
included as parameters to the chat program.
CHAT SCRIPT
The chat script defines the communications.
A script consists of one or more "expect-send" pairs of strings, separated by spaces, with
an optional "subexpect-subsend" string pair, separated by a dash as in the following
example:
ogin:-BREAK-ogin: ppp ssword: hello2u2
This line indicates that the chat program should expect the string "ogin:". If it fails to
receive a login prompt within the time interval allotted, it is to send a break sequence
to the remote and then expect the string "ogin:". If the first "ogin:" is received then
the break sequence is not generated.
Once it received the login prompt the chat program will send the string ppp and then
expect the prompt "ssword:". When it receives the prompt for the password, it will send
the password hello2u2.
A carriage return is normally sent following the reply string. It is not expected in the
"expect" string unless it is specifically requested by using the \r character sequence.
The expect sequence should contain only what is needed to identify the string. Since it is
normally stored on a disk file, it should not contain variable information. It is
generally not acceptable to look for time strings, network identification strings, or
other variable pieces of data as an expect string.
To help correct for characters which may be corrupted during the initial sequence, look
for the string "ogin:" rather than "login:". It is possible that the leading "l" character
may be received in error and you may never find the string even though it was sent by the
system. For this reason, scripts look for "ogin:" rather than "login:" and "ssword:"
rather than "password:".
A very simple script might look like this:
ogin: ppp ssword: hello2u2
In other words, expect ....ogin:, send ppp, expect ...ssword:, send hello2u2.
In actual practice, simple scripts are rare. At the vary least, you should include sub-
expect sequences should the original string not be received. For example, consider the
following script:
ogin:--ogin: ppp ssword: hello2u2
This would be a better script than the simple one used earlier. This would look for the
same login: prompt, however, if one was not received, a single return sequence is sent and
then it will look for login: again. Should line noise obscure the first login prompt then
sending the empty line will usually generate a login prompt again.
COMMENTS
Comments can be embedded in the chat script. A comment is a line which starts with the #
(hash) character in column 1. Such comment lines are just ignored by the chat program. If
a '#' character is to be expected as the first character of the expect sequence, you
should quote the expect string. If you want to wait for a prompt that starts with a #
(hash) character, you would have to write something like this:
# Now wait for the prompt and send logout string
'# ' logout
SENDING DATA FROM A FILE
If the string to send starts with an at sign (@), the rest of the string is taken to be
the name of a file to read to get the string to send. If the last character of the data
read is a newline, it is removed. The file can be a named pipe (or fifo) instead of a
regular file. This provides a way for chat to communicate with another program, for
example, a program to prompt the user and receive a password typed in.
ABORT STRINGS
Many modems will report the status of the call as a string. These strings may be CONNECTED
or NO CARRIER or BUSY. It is often desirable to terminate the script should the modem fail
to connect to the remote. The difficulty is that a script would not know exactly which
modem string it may receive. On one attempt, it may receive BUSY while the next time it
may receive NO CARRIER.
These "abort" strings may be specified in the script using the ABORT sequence. It is
written in the script as in the following example:
ABORT BUSY ABORT 'NO CARRIER' '' ATZ OK ATDT5551212 CONNECT
This sequence will expect nothing; and then send the string ATZ. The expected response to
this is the string OK. When it receives OK, the string ATDT5551212 to dial the telephone.
The expected string is CONNECT. If the string CONNECT is received the remainder of the
script is executed. However, should the modem find a busy telephone, it will send the
string BUSY. This will cause the string to match the abort character sequence. The script
will then fail because it found a match to the abort string. If it received the string NO
CARRIER, it will abort for the same reason. Either string may be received. Either string
will terminate the chat script.
CLR_ABORT STRINGS
This sequence allows for clearing previously set ABORT strings. ABORT strings are kept in
an array of a pre-determined size (at compilation time); CLR_ABORT will reclaim the space
for cleared entries so that new strings can use that space.
SAY STRINGS
The SAY directive allows the script to send strings to the user at the terminal via
standard error. If chat is being run by pppd, and pppd is running as a daemon (detached
from its controlling terminal), standard error will normally be redirected to the file
/etc/ppp/connect-errors.
SAY strings must be enclosed in single or double quotes. If carriage return and line feed
are needed in the string to be output, you must explicitly add them to your string.
The SAY strings could be used to give progress messages in sections of the script where
you want to have 'ECHO OFF' but still let the user know what is happening. An example is:
ABORT BUSY
ECHO OFF
SAY "Dialling your ISP...\n"
'' ATDT5551212
TIMEOUT 120
SAY "Waiting up to 2 minutes for connection ... "
CONNECT ''
SAY "Connected, now logging in ...\n"
ogin: account
ssword: pass
$ \c
SAY "Logged in OK ...\n" etc ...
This sequence will only present the SAY strings to the user and all the details of the
script will remain hidden. For example, if the above script works, the user will see:
Dialling your ISP...
Waiting up to 2 minutes for connection ... Connected, now logging in ...
Logged in OK ...
REPORT STRINGS
A report string is similar to the ABORT string. The difference is that the strings, and
all characters to the next control character such as a carriage return, are written to the
report file.
The report strings may be used to isolate the transmission rate of the modem's connect
string and return the value to the chat user. The analysis of the report string logic
occurs in conjunction with the other string processing such as looking for the expect
string. The use of the same string for a report and abort sequence is probably not very
useful, however, it is possible.
The report strings to no change the completion code of the program.
These "report" strings may be specified in the script using the REPORT sequence. It is
written in the script as in the following example:
REPORT CONNECT ABORT BUSY '' ATDT5551212 CONNECT '' ogin: account
This sequence will expect nothing; and then send the string ATDT5551212 to dial the
telephone. The expected string is CONNECT. If the string CONNECT is received the remainder
of the script is executed. In addition the program will write to the expect-file the
string "CONNECT" plus any characters which follow it such as the connection rate.
CLR_REPORT STRINGS
This sequence allows for clearing previously set REPORT strings. REPORT strings are kept
in an array of a pre-determined size (at compilation time); CLR_REPORT will reclaim the
space for cleared entries so that new strings can use that space.
ECHO
The echo options controls whether the output from the modem is echoed to stderr. This
option may be set with the -e option, but it can also be controlled by the ECHO keyword.
The "expect-send" pair ECHO ON enables echoing, and ECHO OFF disables it. With this
keyword you can select which parts of the conversation should be visible. For instance,
with the following script:
ABORT 'BUSY'
ABORT 'NO CARRIER'
'' ATZ
OK\r\n ATD1234567
\r\n \c
ECHO ON
CONNECT \c
ogin: account
all output resulting from modem configuration and dialing is not visible, but starting
with the CONNECT (or BUSY) message, everything will be echoed.
HANGUP
The HANGUP options control whether a modem hangup should be considered as an error or not.
This option is useful in scripts for dialling systems which will hang up and call your
system back. The HANGUP options can be ON or OFF.
When HANGUP is set OFF and the modem hangs up (e.g., after the first stage of logging in
to a callback system), chat will continue running the script (e.g., waiting for the
incoming call and second stage login prompt). As soon as the incoming call is connected,
you should use the HANGUP ON directive to reinstall normal hang up signal behavior. Here
is an (simple) example script:
ABORT 'BUSY'
'' ATZ
OK\r\n ATD1234567
\r\n \c
CONNECT \c
'Callback login:' call_back_ID
HANGUP OFF
ABORT "Bad Login"
'Callback Password:' Call_back_password
TIMEOUT 120
CONNECT \c
HANGUP ON
ABORT "NO CARRIER"
ogin:--BREAK--ogin: real_account
etc ...
TIMEOUT
The initial timeout value is 45 seconds. This may be changed using the -t parameter. You
can also specify "TIMEOUT 0".
To change the timeout value for the next expect string, the following example may be used:
ATZ OK ATDT5551212 CONNECT TIMEOUT 10 ogin:--ogin: TIMEOUT 5 assword: hello2u2
This will change the timeout to 10 seconds when it expects the login: prompt. The timeout
is then changed to 5 seconds when it looks for the password prompt.
The timeout, once changed, remains in effect until it is changed again.
SENDING EOT
The special reply string of EOT indicates that the chat program should send an EOT
character to the remote. This is normally the End-of-file character sequence. A return
character is not sent following the EOT. The EOT sequence may be embedded into the send
string using the sequence ^D.
GENERATING BREAK
The special reply string of BREAK will cause a break condition to be sent. The break is a
special signal on the transmitter. The normal processing on the receiver is to change the
transmission rate. It may be used to cycle through the available transmission rates on
the remote until you are able to receive a valid login prompt. The break sequence may be
embedded into the send string using the \K sequence.
ESCAPE SEQUENCES
The expect and reply strings may contain escape sequences. All of the sequences are legal
in the reply string. Many are legal in the expect. Those which are not valid in the
expect sequence are so indicated.
'' Expects or sends a null string. If you send a null string then it will still send
the return character. This sequence may either be a pair of apostrophe or quote
characters.
\b represents a backspace character.
\c Suppresses the newline at the end of the reply string. This is the only method to
send a string without a trailing return character. It must be at the end of the
send string. For example, the sequence hello\c will simply send the characters h,
e, l, l, o. (not valid in expect.)
\d Delay for one second. The program uses sleep(1) which will delay to a maximum of
one second. (not valid in expect.)
\K Insert a BREAK (not valid in expect.)
\n Send a newline or linefeed character.
\N Send a null character. The same sequence may be represented by \0. (not valid in
expect.)
\p Pause for a fraction of a second. The delay is 1/10th of a second. (not valid in
expect.)
\q Suppress writing the string to the SYSLOG file. The string ?????? is written to the
log in its place. (not valid in expect.)
\r Send or expect a carriage return.
\s Represents a space character in the string. This may be used when it is not
desirable to quote the strings which contains spaces. The sequence 'HI TIM' and
HI\sTIM are the same.
\t Send or expect a tab character.
\T Send the phone number string as specified with the -T option (not valid in expect.)
\U Send the phone number 2 string as specified with the -U option (not valid in
expect.)
\\ Send or expect a backslash character.
\ddd Collapse the octal digits (ddd) into a single ASCII character and send that
character. (some characters are not valid in expect.)
^C Substitute the sequence with the control character represented by C. For example,
the character DC1 (17) is shown as ^Q. (some characters are not valid in expect.)
ENVIRONMENT VARIABLES
Environment variables are available within chat scripts, if the -E option was specified
in the command line. The metacharacter $ is used to introduce the name of the environment
variable to substitute. If the substitution fails, because the requested environment
variable is not set, nothing is replaced for the variable.
TERMINATION CODES
The chat program will terminate with the following completion codes.
0 The normal termination of the program. This indicates that the script was executed
without error to the normal conclusion.
1 One or more of the parameters are invalid or an expect string was too large for the
internal buffers. This indicates that the program as not properly executed.
2 An error occurred during the execution of the program. This may be due to a read or
write operation failing for some reason or chat receiving a signal such as SIGINT.
3 A timeout event occurred when there was an expect string without having a
"-subsend" string. This may mean that you did not program the script correctly for
the condition or that some unexpected event has occurred and the expected string
could not be found.
4 The first string marked as an ABORT condition occurred.
5 The second string marked as an ABORT condition occurred.
6 The third string marked as an ABORT condition occurred.
7 The fourth string marked as an ABORT condition occurred.
... The other termination codes are also strings marked as an ABORT condition.
Using the termination code, it is possible to determine which event terminated the script.
It is possible to decide if the string "BUSY" was received from the modem as opposed to
"NO DIAL TONE". While the first event may be retried, the second will probably have little
chance of succeeding during a retry.
SEE ALSO
Additional information about chat scripts may be found with UUCP documentation. The chat
script was taken from the ideas proposed by the scripts used by the uucico program.
uucico(1), uucp(1)
COPYRIGHT
The chat program is in public domain. This is not the GNU public license. If it breaks
then you get to keep both pieces.