Provided by: snapraid_13.0-1_amd64 
NAME
snapraid - SnapRAID Backup for Disk Arrays
SYNOPSIS
snapraid [-c, --conf CONFIG]
[-f, --filter PATTERN] [-d, --filter-disk NAME]
[-m, --filter-missing] [-e, --filter-error]
[-a, --audit-only] [-h, --pre-hash] [-i, --import DIR]
[-p, --plan PERC|bad|new|full]
[-o, --older-than DAYS] [-l, --log FILE]
[-s, --spin-down-on-error] [-w, --bw-limit RATE]
[-Z, --force-zero] [-E, --force-empty]
[-U, --force-uuid] [-D, --force-device]
[-N, --force-nocopy] [-F, --force-full]
[-R, --force-realloc]
[-S, --start BLKSTART] [-B, --count BLKCOUNT]
[-L, --error-limit NUMBER]
[-A, --stats]
[-v, --verbose] [-q, --quiet]
status|smart|probe|up|down|diff|sync|scrub|fix|check
|list|dup|pool|devices|touch|rehash
snapraid [-V, --version] [-H, --help] [-C, --gen-conf CONTENT]
DESCRIPTION
SnapRAID is a backup program designed for disk arrays, storing parity information for data recovery in
the event of up to six disk failures.
Primarily intended for home media centers with large, infrequently changing files, SnapRAID offers
several features:
• You can utilize disks already filled with files without the need to reformat them, accessing them
as usual.
• All your data is hashed to ensure data integrity and prevent silent corruption.
• When the number of failed disks exceeds the parity count, data loss is confined to the affected
disks; data on other disks remains accessible.
• If you accidentally delete files on a disk, recovery is possible.
• Disks can have different sizes.
• You can add disks at any time.
• SnapRAID doesn´t lock in your data; you can stop using it anytime without reformatting or moving
data.
• To access a file, only a single disk needs to spin, saving power and reducing noise.
For more information, please visit the official SnapRAID site:
https://www.snapraid.it/
LIMITATIONS
SnapRAID is a hybrid between a RAID and a backup program, aiming to combine the best benefits of both.
However, it has some limitations that you should consider before using it.
The main limitation is that if a disk fails and you haven´t recently synced, you may not be able to fully
recover. More specifically, you may be unable to recover up to the size of the changed or deleted files
since the last sync operation. This occurs even if the changed or deleted files are not on the failed
disk. This is why SnapRAID is better suited for data that rarely changes.
On the other hand, newly added files don´t prevent recovery of already existing files. You will only lose
the recently added files if they are on the failed disk.
Other SnapRAID limitations are:
• With SnapRAID, you still have separate file systems for each disk. With RAID, you get a single
large file system.
• SnapRAID doesn´t stripe data. With RAID, you get a speed boost with striping.
• SnapRAID doesn´t support real-time recovery. With RAID, you do not have to stop working when a
disk fails.
• SnapRAID can recover data only from a limited number of disk failures. With a backup, you can
recover from a complete failure of the entire disk array.
• Only file names, timestamps, symlinks, and hardlinks are saved. Permissions, ownership, and
extended attributes are not saved.
GETTING STARTED
To use SnapRAID, you need to first select one disk in your disk array to dedicate to "parity"
information. With one disk for parity, you will be able to recover from a single disk failure, similar to
RAID5.
If you want to recover from more disk failures, similar to RAID6, you must reserve additional disks for
parity. Each additional parity disk allows recovery from one more disk failure.
As parity disks, you must pick the largest disks in the array, as the parity information may grow to the
size of the largest data disk in the array.
These disks will be dedicated to storing the "parity" files. You should not store your data on them.
Then, you must define the "data" disks that you want to protect with SnapRAID. The protection is more
effective if these disks contain data that rarely changes. For this reason, it´s better to NOT include
the Windows C:\ disk or the Unix /home, /var, and /tmp directories.
The list of files is saved in the "content" files, usually stored on the data, parity, or boot disks.
This file contains the details of your backup, including all the checksums to verify its integrity. The
"content" file is stored in multiple copies, and each copy must be on a different disk to ensure that,
even in case of multiple disk failures, at least one copy is available.
For example, suppose you are interested in only one parity level of protection, and your disks are
located at:
/mnt/diskp <- selected disk for parity
/mnt/disk1 <- first disk to protect
/mnt/disk2 <- second disk to protect
/mnt/disk3 <- third disk to protect
You must create the configuration file /etc/snapraid.conf with the following options:
parity /mnt/diskp/snapraid.parity
content /var/lib/snapraid/snapraid.content
content /mnt/disk1/snapraid.content
content /mnt/disk2/snapraid.content
data d1 /mnt/disk1/
data d2 /mnt/disk2/
data d3 /mnt/disk3/
If you are on Windows, you should use the Windows path format, with drive letters and backslashes instead
of slashes.
parity E:\snapraid.parity
content C:\snapraid\snapraid.content
content F:\array\snapraid.content
content G:\array\snapraid.content
data d1 F:\array\
data d2 G:\array\
data d3 H:\array\
If you have many disks and run out of drive letters, you can mount disks directly in subfolders. See:
https://www.google.com/search?q=Windows+mount+point
At this point, you are ready to run the "sync" command to build the parity information.
snapraid sync
This process may take several hours the first time, depending on the size of the data already present on
the disks. If the disks are empty, the process is immediate.
You can stop it at any time by pressing Ctrl+C, and at the next run, it will resume where it was
interrupted.
When this command completes, your data is SAFE.
Now you can start using your array as you like and periodically update the parity information by running
the "sync" command.
Scrubbing
To periodically check the data and parity for errors, you can run the "scrub" command.
snapraid scrub
This command compares the data in your array with the hash computed during the "sync" command to verify
integrity.
Each run of the command checks approximately 8% of the array, excluding data already scrubbed in the
previous 10 days. You can use the -p, --plan option to specify a different amount and the -o,
--older-than option to specify a different age in days. For example, to check 5% of the array for blocks
older than 20 days, use:
snapraid -p 5 -o 20 scrub
If silent or input/output errors are found during the process, the corresponding blocks are marked as bad
in the "content" file and listed in the "status" command.
snapraid status
To fix them, you can use the "fix" command, filtering for bad blocks with the -e, --filter-error option:
snapraid -e fix
At the next "scrub," the errors will disappear from the "status" report if they are truly fixed. To make
it faster, you can use -p bad to scrub only blocks marked as bad.
snapraid -p bad scrub
Running "scrub" on an unsynced array may report errors caused by removed or modified files. These errors
are reported in the "scrub" output, but the related blocks are not marked as bad.
Pooling
Note: The pooling feature described below has been superseded by the mergefs tool, which is now the
recommended option for Linux users in the SnapRAID community. Mergefs provides a more flexible and
efficient way to pool multiple drives into a single unified mount point, allowing seamless access to
files across your array without relying on symbolic links. It integrates well with SnapRAID for parity
protection and is commonly used in setups like OpenMediaVault (OMV) or custom NAS configurations.
To have all the files in your array shown in the same directory tree, you can enable the "pooling"
feature. It creates a read-only virtual view of all the files in your array using symbolic links.
You can configure the "pooling" directory in the configuration file with:
pool /pool
or, if you are on Windows, with:
pool C:\pool
and then run the "pool" command to create or update the virtual view.
snapraid pool
If you are using a Unix platform and want to share this directory over the network to either Windows or
Unix machines, you should add the following options to your /etc/samba/smb.conf:
# In the global section of smb.conf
unix extensions = no
# In the share section of smb.conf
[pool]
comment = Pool
path = /pool
read only = yes
guest ok = yes
wide links = yes
follow symlinks = yes
In Windows, sharing symbolic links over a network requires clients to resolve them remotely. To enable
this, besides sharing the pool directory, you must also share all the disks independently, using the disk
names defined in the configuration file as share points. You must also specify in the "share" option of
the configuration file the Windows UNC path that remote clients need to use to access these shared disks.
For example, operating from a server named "darkstar", you can use the options:
data d1 F:\array\
data d2 G:\array\
data d3 H:\array\
pool C:\pool
share \\darkstar
and share the following directories over the network:
\\darkstar\pool -> C:\pool
\\darkstar\d1 -> F:\array
\\darkstar\d2 -> G:\array
\\darkstar\d3 -> H:\array
to allow remote clients to access all the files at \\darkstar\pool.
You may also need to configure remote clients to enable access to remote symlinks with the command:
fsutil behavior set SymlinkEvaluation L2L:1 R2R:1 L2R:1 R2L:1
Undeleting
SnapRAID functions more like a backup program than a RAID system, and it can be used to restore or
undelete files to their previous state using the -f, --filter option:
snapraid fix -f FILE
or for a directory:
snapraid fix -f DIR/
You can also use it to recover only accidentally deleted files inside a directory using the -m,
--filter-missing option, which restores only missing files, leaving all others untouched.
snapraid fix -m -f DIR/
Or to recover all the deleted files on all drives with:
snapraid fix -m
Recovering
The worst has happened, and you have lost one or more disks!
DO NOT PANIC! You will be able to recover them!
The first thing you must do is avoid further changes to your disk array. Disable any remote connections
to it and any scheduled processes, including any scheduled SnapRAID nightly sync or scrub.
Then proceed with the following steps.
STEP 1 -> Reconfigure
You need some space to recover, ideally on additional spare disks, but an external USB disk or remote
disk will suffice.
Modify the SnapRAID configuration file to make the "data" or "parity" option of the failed disk point to
a location with enough empty space to recover the files.
For example, if disk "d1" has failed, change from:
data d1 /mnt/disk1/
to:
data d1 /mnt/new_spare_disk/
If the disk to recover is a parity disk, update the appropriate "parity" option. If you have multiple
failed disks, update all their configuration options.
STEP 2 -> Fix
Run the fix command, storing the log in an external file with:
snapraid -d NAME -l fix.log fix
Where NAME is the name of the disk, such as "d1" in our previous example. If the disk to recover is a
parity disk, use the names "parity", "2-parity", etc. If you have multiple failed disks, use multiple -d
options to specify all of them.
This command will take a long time.
Ensure you have a few gigabytes free to store the fix.log file. Run it from a disk with sufficient free
space.
Now you have recovered all that is recoverable. If some files are partially or totally unrecoverable,
they will be renamed by adding the ".unrecoverable" extension.
You can find a detailed list of all unrecoverable blocks in the fix.log file by checking all lines
starting with "unrecoverable:".
If you are not satisfied with the recovery, you can retry it as many times as you wish.
For example, if you have removed files from the array after the last "sync", this may result in some
files not being recovered. In this case, you can retry the "fix" using the -i, --import option,
specifying where these files are now to include them again in the recovery process.
If you are satisfied with the recovery, you can proceed further, but note that after syncing, you cannot
retry the "fix" command anymore!
STEP 3 -> Check
As a cautious check, you can now run a "check" command to ensure that everything is correct on the
recovered disk.
snapraid -d NAME -a check
Where NAME is the name of the disk, such as "d1" in our previous example.
The -d and -a options tell SnapRAID to check only the specified disk and ignore all parity data.
This command will take a long time, but if you are not overly cautious, you can skip it.
STEP 4 -> Sync
Run the "sync" command to resynchronize the array with the new disk.
snapraid sync
If everything is recovered, this command is immediate.
COMMANDS
SnapRAID provides a few simple commands that allow you to:
• Print the status of the array -> "status"
• Control the disks -> "smart", "probe", "up", "down"
• Make a backup/snapshot -> "sync"
• Periodically check data -> "scrub"
• Restore the last backup/snapshot -> "fix".
Commands must be written in lowercase.
status
Prints a summary of the state of the disk array.
It includes information about parity fragmentation, how old the blocks are without checking, and all
recorded silent errors encountered while scrubbing.
The information presented refers to the latest time you ran "sync". Later modifications are not taken
into account.
If bad blocks were detected, their block numbers are listed. To fix them, you can use the "fix -e"
command.
It also shows a graph representing the last time each block was scrubbed or synced. Scrubbed blocks are
shown with ´*´, blocks synced but not yet scrubbed with ´o´.
Nothing is modified.
smart
Prints a SMART report of all the disks in the system.
It includes an estimation of the probability of failure in the next year, allowing you to plan
maintenance replacements of disks that show suspicious attributes.
This probability estimation is obtained by correlating the SMART attributes of the disks with the
Backblaze data available at:
https://www.backblaze.com/hard-drive-test-data.html
If SMART reports that a disk is failing, "FAIL" or "PREFAIL" is printed for that disk, and SnapRAID
returns with an error. In this case, immediate replacement of the disk is highly recommended.
Other possible status strings are:
logfail In the past, some attributes were lower than the threshold.
logerr The device error log contains errors.
selferr The device self-test log contains errors.
If the -v, --verbose option is specified, a deeper statistical analysis is provided. This analysis can
help you decide if you need more or less parity.
This command uses the "smartctl" tool and is equivalent to running "smartctl -a" on all devices.
If your devices are not auto-detected correctly, you can specify a custom command using the "smartctl"
option in the configuration file.
Nothing is modified.
probe
Prints the POWER state of all disks in the system.
"Standby" means the disk is not spinning. "Active" means the disk is spinning.
This command uses the "smartctl" tool and is equivalent to running "smartctl -n standby -i" on all
devices.
If your devices are not auto-detected correctly, you can specify a custom command using the "smartctl"
option in the configuration file.
Nothing is modified.
up
Spins up all the disks of the array.
You can spin up only specific disks using the -d, --filter-disk option.
Spinning up all the disks at the same time requires a lot of power. Ensure that your power supply can
sustain it.
Nothing is modified.
down
Spins down all the disks of the array.
This command uses the "smartctl" tool and is equivalent to running "smartctl -s standby,now" on all
devices.
You can spin down only specific disks using the -d, --filter-disk option.
To automatically spin down on error, you can use the -s, --spin-down-on-error option with any other
command, which is equivalent to running "down" manually when an error occurs.
Nothing is modified.
diff
Lists all the files modified since the last "sync" that need to have their parity data recomputed.
This command doesn´t check the file data, but only the file timestamp, size, and inode.
After listing all changed files, a summary of the changes is presented, grouped by:
equal Files unchanged from before.
added Files added that were not present before.
removed Files removed.
updated Files with a different size or timestamp, meaning they were modified.
moved Files moved to a different directory on the same disk. They are identified by having the same
name, size, timestamp, and inode, but a different directory.
copied Files copied on the same or a different disk. Note that if they are truly moved to a different
disk, they will also be counted in "removed". They are identified by having the same name, size,
and timestamp. If the sub-second timestamp is zero, the full path must match, not just the name.
restored Files with a different inode but matching name, size, and timestamp. These are usually
files restored after being deleted.
If a "sync" is required, the process return code is 2, instead of the default 0. The return code 1 is
used for a generic error condition.
Nothing is modified.
sync
Updates the parity information. All modified files in the disk array are read, and the corresponding
parity data is updated.
You can stop this process at any time by pressing Ctrl+C, without losing the work already done. At the
next run, the "sync" process will resume where it was interrupted.
If silent or input/output errors are found during the process, the corresponding blocks are marked as
bad.
Files are identified by path and/or inode and checked by size and timestamp. If the file size or
timestamp differs, the parity data is recomputed for the entire file. If the file is moved or renamed on
the same disk, keeping the same inode, the parity is not recomputed. If the file is moved to another
disk, the parity is recomputed, but the previously computed hash information is retained.
The "content" and "parity" files are modified if necessary. The files in the array are NOT modified.
scrub
Scrubs the array, checking for silent or input/output errors in data and parity disks.
Each invocation checks approximately 8% of the array, excluding data already scrubbed in the last 10
days. This means that scrubbing once a week ensures every bit of data is checked at least once every
three months.
You can define a different scrub plan or amount using the -p, --plan option, which accepts: bad - Scrub
blocks marked bad. new - Scrub just-synced blocks not yet scrubbed. full - Scrub everything. 0-100 -
Scrub the specified percentage of blocks.
If you specify a percentage amount, you can also use the -o, --older-than option to define how old the
block should be. The oldest blocks are scrubbed first, ensuring an optimal check. If you want to scrub
only the just-synced blocks not yet scrubbed, use the "-p new" option.
To get details of the scrub status, use the "status" command.
For any silent or input/output error found, the corresponding blocks are marked as bad in the "content"
file. These bad blocks are listed in "status" and can be fixed with "fix -e". After the fix, at the
next scrub, they will be rechecked, and if found corrected, the bad mark will be removed. To scrub only
the bad blocks, you can use the "scrub -p bad" command.
It´s recommended to run "scrub" only on a synced array to avoid reported errors caused by unsynced data.
These errors are recognized as not being silent errors, and the blocks are not marked as bad, but such
errors are reported in the output of the command.
The "content" file is modified to update the time of the last check for each block and to mark bad
blocks. The "parity" files are NOT modified. The files in the array are NOT modified.
fix
Fixes all the files and the parity data.
All files and parity data are compared with the snapshot state saved in the last "sync". If a difference
is found, it is reverted to the stored snapshot.
WARNING! The "fix" command does not differentiate between errors and intentional modifications. It
unconditionally reverts the file state to the last "sync".
If no other option is specified, the entire array is processed. Use the filter options to select a
subset of files or disks to operate on.
To fix only the blocks marked bad during "sync" and "scrub", use the -e, --filter-error option. Unlike
other filter options, this one applies fixes only to files that are unchanged since the latest "sync".
SnapRAID renames all files that cannot be fixed by adding the ".unrecoverable" extension.
Before fixing, the entire array is scanned to find any files moved since the last "sync" operation.
These files are identified by their timestamp, ignoring their name and directory, and are used in the
recovery process if necessary. If you moved some of them outside the array, you can use the -i, --import
option to specify additional directories to scan.
Files are identified only by path, not by inode.
The "content" file is NOT modified. The "parity" files are modified if necessary. The files in the
array are modified if necessary.
check
Verifies all the files and the parity data.
It works like "fix", but it only simulates a recovery and no changes are written to the array.
This command is primarily intended for manual verification, such as after a recovery process or in other
special conditions. For periodic and scheduled checks, use "scrub".
If you use the -a, --audit-only option, only the file data is checked, and the parity data is ignored for
a faster run.
Files are identified only by path, not by inode.
Nothing is modified.
list
Lists all the files contained in the array at the time of the last "sync".
With -v or --verbose, the subsecond time is also shown.
Nothing is modified.
dup
Lists all duplicate files. Two files are assumed equal if their hashes match. The file data is not read;
only the precomputed hashes are used.
Nothing is modified.
pool
Creates or updates a virtual view of all the files in your disk array in the "pooling" directory.
The files are not copied but linked using symbolic links.
When updating, all existing symbolic links and empty subdirectories are deleted and replaced with the new
view of the array. Any other regular files are left in place.
Nothing is modified outside the pool directory.
devices
Prints the low-level devices used by the array.
This command displays the device associations in the array and is mainly intended as a script interface.
The first two columns are the low-level device ID and path. The next two columns are the high-level
device ID and path. The last column is the disk name in the array.
In most cases, you have one low-level device for each disk in the array, but in some more complex
configurations, you may have multiple low-level devices used by a single disk in the array.
Nothing is modified.
touch
Sets an arbitrary sub-second timestamp for all files that have it set to zero.
This improves SnapRAID´s ability to recognize moved and copied files, as it makes the timestamp almost
unique, reducing possible duplicates.
More specifically, if the sub-second timestamp is not zero, a moved or copied file is identified as such
if it matches the name, size, and timestamp. If the sub-second timestamp is zero, it is considered a copy
only if the full path, size, and timestamp all match.
The second-precision timestamp is not modified, so all the dates and times of your files will be
preserved.
rehash
Schedules a rehash of the entire array.
This command changes the hash kind used, typically when upgrading from a 32-bit system to a 64-bit one,
to switch from MurmurHash3 to the faster SpookyHash.
If you are already using the optimal hash, this command does nothing and informs you that no action is
needed.
The rehash is not performed immediately but takes place progressively during "sync" and "scrub".
You can check the rehash state using "status".
During the rehash, SnapRAID maintains full functionality, with the only exception that "dup" cannot
detect duplicated files using a different hash.
OPTIONS
SnapRAID provides the following options:
-c, --conf CONFIG
Selects the configuration file to use. If not specified, in Unix it uses the file
"/usr/local/etc/snapraid.conf" if it exists, otherwise "/etc/snapraid.conf". In Windows, it uses
the file "snapraid.conf" in the same directory as "snapraid.exe".
-f, --filter PATTERN
Filters the files to process in "check" and "fix". Only the files matching the specified pattern
are processed. This option can be used multiple times. See the PATTERN section for more details
on pattern specifications. In Unix, ensure globbing characters are quoted if used. This option
can be used only with "check" and "fix". It cannot be used with "sync" and "scrub", as they
always process the entire array.
-d, --filter-disk NAME
Filters the disks to process in "check", "fix", "up", and "down". You must specify a disk name as
defined in the configuration file. You can also specify parity disks with the names: "parity",
"2-parity", "3-parity", etc., to limit operations to a specific parity disk. If you combine
multiple --filter, --filter-disk, and --filter-missing options, only files matching all the
filters are selected. This option can be used multiple times. This option can be used only with
"check", "fix", "up", and "down". It cannot be used with "sync" and "scrub", as they always
process the entire array.
-m, --filter-missing
Filters the files to process in "check" and "fix". Only the files missing or deleted from the
array are processed. When used with "fix", this acts as an "undelete" command. If you combine
multiple --filter, --filter-disk, and --filter-missing options, only files matching all the
filters are selected. This option can be used only with "check" and "fix". It cannot be used
with "sync" and "scrub", as they always process the entire array.
-e, --filter-error
Processes the files with errors in "check" and "fix". It processes only files that have blocks
marked with silent or input/output errors during "sync" and "scrub", as listed in "status". This
option can be used only with "check" and "fix".
-p, --plan PERC|bad|new|full
Selects the scrub plan. If PERC is a numeric value from 0 to 100, it is interpreted as the
percentage of blocks to scrub. Instead of a percentage, you can specify a plan: "bad" scrubs bad
blocks, "new" scrubs blocks not yet scrubbed, and "full" scrubs everything. This option can be
used only with "scrub".
-o, --older-than DAYS
Selects the oldest part of the array to process in "scrub". DAYS is the minimum age in days for a
block to be scrubbed; the default is 10. Blocks marked as bad are always scrubbed regardless of
this option. This option can be used only with "scrub".
-a, --audit-only
In "check", verifies the hash of the files without checking the parity data. If you are
interested only in checking the file data, this option can significantly speed up the checking
process. This option can be used only with "check".
-h, --pre-hash
In "sync", runs a preliminary hashing phase of all new data for additional verification before the
parity computation. Usually, in "sync", no preliminary hashing is done, and the new data is
hashed just before the parity computation when it is read for the first time. This process occurs
when the system is under heavy load, with all disks spinning and a busy CPU. This is an extreme
condition for the machine, and if it has a latent hardware problem, silent errors may go
undetected because the data is not yet hashed. To avoid this risk, you can enable the "pre-hash"
mode to have all the data read twice to ensure its integrity. This option also verifies files
moved within the array to ensure the move operation was successful and, if necessary, allows you
to run a fix operation before proceeding. This option can be used only with "sync".
-i, --import DIR
Imports from the specified directory any files deleted from the array after the last "sync". If
you still have such files, they can be used by "check" and "fix" to improve the recovery process.
The files are read, including in subdirectories, and are identified regardless of their name.
This option can be used only with "check" and "fix".
-s, --spin-down-on-error
On any error, spins down all managed disks before exiting with a non-zero status code. This
prevents the drives from remaining active and spinning after an aborted operation, helping to
avoid unnecessary heat buildup and power consumption. Use this option to ensure disks are safely
stopped even when a command fails.
-w, --bw-limit RATE
Applies a global bandwidth limit for all disks. The RATE is the number of bytes per second. You
can specify a multiplier such as K, M, or G (e.g., --bw-limit 1G).
-A, --stats
Enables an extended status view that shows additional information. The screen displays two
graphs: The first graph shows the number of buffered stripes for each disk, along with the file
path of the file currently being accessed on that disk. Typically, the slowest disk will have no
buffer available, which determines the maximum achievable bandwidth. The second graph shows the
percentage of time spent waiting over the past 100 seconds. The slowest disk is expected to cause
most of the wait time, while other disks should have little or no wait time because they can use
their buffered stripes. This graph also shows the time spent waiting for hash calculations and
RAID computations. All computations run in parallel with disk operations. Therefore, as long as
there is measurable wait time for at least one disk, it indicates that the CPU is fast enough to
keep up with the workload.
-Z, --force-zero
Forces the insecure operation of syncing a file with zero size that was previously non-zero. If
SnapRAID detects such a condition, it stops proceeding unless you specify this option. This
allows you to easily detect when, after a system crash, some accessed files were truncated. This
is a possible condition in Linux with the ext3/ext4 file systems. This option can be used only
with "sync".
-E, --force-empty
Forces the insecure operation of syncing a disk with all the original files missing. If SnapRAID
detects that all the files originally present on the disk are missing or rewritten, it stops
proceeding unless you specify this option. This allows you to easily detect when a data file
system is not mounted. This option can be used only with "sync".
-U, --force-uuid
Forces the insecure operation of syncing, checking, and fixing with disks that have changed their
UUID. If SnapRAID detects that some disks have changed UUID, it stops proceeding unless you
specify this option. This allows you to detect when your disks are mounted at the wrong mount
points. It is, however, allowed to have a single UUID change with single parity, and more with
multiple parity, because this is the normal case when replacing disks after a recovery. This
option can be used only with "sync", "check", or "fix".
-D, --force-device
Forces the insecure operation of fixing with inaccessible disks or with disks on the same physical
device. For example, if you lost two data disks and have a spare disk to recover only the first
one, you can ignore the second inaccessible disk. Or, if you want to recover a disk in the free
space left on an already used disk, sharing the same physical device. This option can be used
only with "fix".
-N, --force-nocopy
In "sync", "check", and "fix", disables the copy detection heuristic. Without this option,
SnapRAID assumes that files with the same attributes, such as name, size, and timestamp, are
copies with the same data. This allows identification of copied or moved files from one disk to
another and reuses the already computed hash information to detect silent errors or to recover
missing files. In some rare cases, this behavior may result in false positives or a slow process
due to many hash verifications, and this option allows you to resolve such issues. This option
can be used only with "sync", "check", and "fix".
-F, --force-full
In "sync", forces a full recomputation of the parity. This option can be used when you add a new
parity level or if you reverted to an old content file using more recent parity data. Instead of
recreating the parity from scratch, this allows you to reuse the hashes present in the content
file to validate data and maintain data protection during the "sync" process using the existing
parity data. This option can be used only with "sync".
-R, --force-realloc
In "sync", forces a full reallocation of files and rebuild of the parity. This option can be used
to completely reallocate all files, removing fragmentation, while reusing the hashes present in
the content file to validate data. This option can be used only with "sync". WARNING! This
option is for experts only, and it is highly recommended not to use it. You DO NOT have data
protection during the "sync" operation.
-l, --log FILE
Writes a detailed log to the specified file. If this option is not specified, unexpected errors
are printed to the screen, potentially resulting in excessive output in case of many errors. When
-l, --log is specified, only fatal errors that cause SnapRAID to stop are printed to the screen.
If the path starts with ´>>´, the file is opened in append mode. Occurrences of ´%D´ and ´%T´ in
the name are replaced with the date and time in the format YYYYMMDD and HHMMSS. In Windows batch
files, you must double the ´%´ character, e.g., result-%%D.log. To use ´>>´, you must enclose the
name in quotes, e.g., ">>result.log". To output the log to standard output or standard error, you
can use ">&1" and ">&2", respectively.
-L, --error-limit NUMBER
Sets a new error limit before stopping execution. By default, SnapRAID stops if it encounters
more than 100 input/output errors, indicating that a disk is likely failing. This option affects
"sync" and "scrub", which are allowed to continue after the first set of disk errors to try to
complete their operations. However, "check" and "fix" always stop at the first error.
-S, --start BLKSTART
Starts processing from the specified block number. This can be useful for retrying to check or fix
specific blocks in case of a damaged disk. This option is mainly for advanced manual recovery.
-B, --count BLKCOUNT
Processes only the specified number of blocks. This option is mainly for advanced manual
recovery.
-C, --gen-conf CONTENT
Generates a dummy configuration file from an existing content file. The configuration file is
written to standard output and does not overwrite an existing one. This configuration file also
contains the information needed to reconstruct the disk mount points in case you lose the entire
system.
-v, --verbose
Prints more information to the screen. If specified once, it prints excluded files and additional
statistics. This option has no effect on the log files.
-q, --quiet
Prints less information to the screen. If specified once, it removes the progress bar; twice, the
running operations; three times, the info messages; four times, the status messages. Fatal errors
are always printed to the screen. This option has no effect on the log files.
-H, --help
Prints a short help screen.
-V, --version
Prints the program version.
CONFIGURATION
SnapRAID requires a configuration file to know where your disk array is located and where to store the
parity information.
In Unix, it uses the file "/usr/local/etc/snapraid.conf" if it exists, otherwise "/etc/snapraid.conf".
In Windows, it uses the file "snapraid.conf" in the same directory as "snapraid.exe".
It must contain the following options (case-sensitive):
parity FILE [,FILE] ...
Defines the files to use to store the parity information. The parity enables protection from a single
disk failure, similar to RAID5.
You can specify multiple files, which must be on different disks. When a file cannot grow anymore, the
next one is used. The total space available must be at least as large as the largest data disk in the
array.
You can add additional parity files later, but you cannot reorder or remove them.
Keeping the parity disks reserved for parity ensures that they do not become fragmented, improving
performance.
In Windows, 256 MB is left unused on each disk to avoid the warning about full disks.
This option is mandatory and can be used only once.
(2,3,4,5,6)-parity FILE [,FILE] ...
Defines the files to use to store extra parity information.
For each parity level specified, one additional level of protection is enabled:
• 2-parity enables RAID6 dual parity.
• 3-parity enables triple parity.
• 4-parity enables quad (four) parity.
• 5-parity enables penta (five) parity.
• 6-parity enables hexa (six) parity.
Each parity level requires the presence of all previous parity levels.
The same considerations as for the ´parity´ option apply.
These options are optional and can be used only once.
z-parity FILE [,FILE] ...
Defines an alternate file and format to store triple parity.
This option is an alternative to ´3-parity´, primarily intended for low-end CPUs like ARM or AMD Phenom,
Athlon, and Opteron that do not support the SSSE3 instruction set. In such cases, it provides better
performance.
This format is similar to but faster than the one used by ZFS RAIDZ3. Like ZFS, it does not work beyond
triple parity.
When using ´3-parity´, you will be warned if it is recommended to use the ´z-parity´ format for
performance improvement.
It is possible to convert from one format to another by adjusting the configuration file with the desired
z-parity or 3-parity file and using ´fix´ to recreate it.
content FILE
Defines the file to use to store the list and checksums of all the files present in your disk array.
It can be placed on a disk used for data, parity, or any other disk available. If you use a data disk,
this file is automatically excluded from the "sync" process.
This option is mandatory and can be used multiple times to save multiple copies of the same file.
You must store at least one copy for each parity disk used plus one. Using additional copies does not
hurt.
data NAME DIR
Defines the name and mount point of the data disks in the array. NAME is used to identify the disk and
must be unique. DIR is the mount point of the disk in the file system.
You can change the mount point as needed, as long as you keep the NAME fixed.
You should use one option for each data disk in the array.
You can rename a disk later by changing the NAME directly in the configuration file and then running a
´sync´ command. In the case of renaming, the association is done using the stored UUID of the disks.
nohidden
Excludes all hidden files and directories. In Unix, hidden files are those starting with ".". In
Windows, they are those with the hidden attribute.
exclude/include PATTERN
Defines the file or directory patterns to exclude or include in the sync process. All patterns are
processed in the specified order.
If the first pattern that matches is an "exclude" one, the file is excluded. If it is an "include" one,
the file is included. If no pattern matches, the file is excluded if the last pattern specified is an
"include", or included if the last pattern specified is an "exclude".
See the PATTERN section for more details on pattern specifications.
This option can be used multiple times.
blocksize SIZE_IN_KIBIBYTES
Defines the basic block size in kibibytes for the parity. One kibibyte is 1024 bytes.
The default blocksize is 256, which should work for most cases.
WARNING! This option is for experts only, and it is highly recommended not to change this value. To
change this value in the future, you will need to recreate the entire parity!
A reason to use a different blocksize is if you have many small files, on the order of millions.
For each file, even if only a few bytes, an entire block of parity is allocated, and with many files,
this may result in significant unused parity space. When you completely fill the parity disk, you are
not allowed to add more files to the data disks. However, the wasted parity does not accumulate across
data disks. Wasted space resulting from a high number of files on a data disk limits only the amount of
data on that data disk, not others.
As an approximation, you can assume that half of the block size is wasted for each file. For example,
with 100,000 files and a 256 KiB block size, you will waste 12.8 GB of parity, which may result in 12.8
GB less space available on the data disk.
You can check the amount of wasted space on each disk using "status". This is the amount of space you
must leave free on the data disks or use for files not included in the array. If this value is negative,
it means you are close to filling the parity, and it represents the space you can still waste.
To avoid this issue, you can use a larger partition for parity. For example, if the parity partition is
12.8 GB larger than the data disks, you have enough extra space to handle up to 100,000 files on each
data disk without any wasted space.
A trick to get a larger parity partition in Linux is to format it with the command:
mkfs.ext4 -m 0 -T largefile4 DEVICE
This results in about 1.5% extra space, approximately 60 GB for a 4 TB disk, which allows about 460,000
files on each data disk without any wasted space.
hashsize SIZE_IN_BYTES
Defines the hash size in bytes for the saved blocks.
The default hashsize is 16 bytes (128 bits), which should work for most cases.
WARNING! This option is for experts only, and it is highly recommended not to change this value. To
change this value in the future, you will need to recreate the entire parity!
A reason to use a different hashsize is if your system has limited memory. As a rule of thumb, SnapRAID
typically requires 1 GiB of RAM for each 16 TB of data in the array.
Specifically, to store the hashes of the data, SnapRAID requires approximately TS*(1+HS)/BS bytes of RAM,
where TS is the total size in bytes of your disk array, BS is the block size in bytes, and HS is the hash
size in bytes.
For example, with 8 disks of 4 TB, a block size of 256 KiB (1 KiB = 1024 bytes), and a hash size of 16,
you get:
RAM = (8 * 4 * 10^12) * (1+16) / (256 * 2^10) = 1.93 GiB
Switching to a hash size of 8, you get:
RAM = (8 * 4 * 10^12) * (1+8) / (256 * 2^10) = 1.02 GiB
Switching to a block size of 512, you get:
RAM = (8 * 4 * 10^12) * (1+16) / (512 * 2^10) = 0.96 GiB
Switching to both a hash size of 8 and a block size of 512, you get:
RAM = (8 * 4 * 10^12) * (1+8) / (512 * 2^10) = 0.51 GiB
autosave SIZE_IN_GIGABYTES
Automatically saves the state when syncing or scrubbing after the specified amount of GB processed. This
option is useful to avoid restarting long "sync" commands from scratch if interrupted by a machine crash
or any other event.
temp_limit TEMPERATURE_CELSIUS
Sets the maximum allowed disk temperature in Celsius. When specified, SnapRAID periodically checks the
temperature of all disks using the smartctl tool. The current disk temperatures are displayed while
SnapRAID is operating. If any disk exceeds this limit, all operations stop, and the disks are spun down
(put into standby) for the duration defined by the "temp_sleep" option. After the sleep period,
operations resume, potentially pausing again if the temperature limit is reached once more.
During operation, SnapRAID also analyzes the heating curve of each disk and estimates the long-term
steady temperature they are expected to reach if activity continues. The estimation is performed only
after the disk temperature has increased four times, ensuring that enough data points are available to
establish a reliable trend. This predicted steady temperature is shown in parentheses next to the
current value and helps assess whether the system´s cooling is adequate. This estimated temperature is
for informational purposes only and has no effect on the behavior of SnapRAID. The program´s actions are
based solely on the actual measured disk temperatures.
To perform this analysis, SnapRAID needs a reference for the system temperature. It first attempts to
read it from available hardware sensors. If no system sensor can be accessed, it uses the lowest disk
temperature measured at the start of the run as a fallback reference.
Normally, SnapRAID shows only the temperature of the hottest disk. To display the temperature of all
disks, use the -A or --stats option.
temp_sleep TIME_IN_MINUTES
Sets the standby time, in minutes, when the temperature limit is reached. During this period, the disks
remain spun down. The default is 5 minutes.
pool DIR
Defines the pooling directory where the virtual view of the disk array is created using the "pool"
command.
The directory must already exist.
share UNC_DIR
Defines the Windows UNC path required to access the disks remotely.
If this option is specified, the symbolic links created in the pool directory use this UNC path to access
the disks. Without this option, the symbolic links generated use only local paths, which does not allow
sharing the pool directory over the network.
The symbolic links are formed using the specified UNC path, adding the disk name as specified in the
"data" option, and finally adding the file directory and name.
This option is required only for Windows.
smartctl DISK/PARITY OPTIONS...
Defines custom smartctl options to obtain the SMART attributes for each disk. This may be required for
RAID controllers and some USB disks that cannot be auto-detected. The %s placeholder is replaced by the
device name, but it is optional for fixed devices like RAID controllers.
DISK is the same disk name specified in the "data" option. PARITY is one of the parity names: "parity",
"2-parity", "3-parity", "4-parity", "5-parity", "6-parity", or "z-parity".
In the specified OPTIONS, the "%s" string is replaced by the device name. For RAID controllers, the
device is likely fixed, and you may not need to use "%s".
Refer to the smartmontools documentation for possible options:
https://www.smartmontools.org/wiki/Supported_RAID-Controllers
https://www.smartmontools.org/wiki/Supported_USB-Devices
For example:
smartctl parity -d sat %s
smartignore DISK/PARITY ATTR [ATTR...]
Ignores the specified SMART attribute when computing the probability of disk failure. This option is
useful if a disk reports unusual or misleading values for a particular attribute.
DISK is the same disk name specified in the "data" option. PARITY is one of the parity names: "parity",
"2-parity", "3-parity", "4-parity", "5-parity", "6-parity", or "z-parity". The special value * can be
used to ignore the attribute on all disks.
For example, to ignore the "Current Pending Sector Count" attribute on all disks:
smartignore * 197
To ignore it only on the first parity disk:
smartignore parity 197
Examples
An example of a typical configuration for Unix is:
parity /mnt/diskp/snapraid.parity
content /mnt/diskp/snapraid.content
content /var/lib/snapraid/snapraid.content
data d1 /mnt/disk1/
data d2 /mnt/disk2/
data d3 /mnt/disk3/
exclude /lost+found/
exclude /tmp/
smartctl d1 -d sat %s
smartctl d2 -d usbjmicron %s
smartctl parity -d areca,1/1 /dev/sg0
smartctl 2-parity -d areca,2/1 /dev/sg0
An example of a typical configuration for Windows is:
parity E:\snapraid.parity
content E:\snapraid.content
content C:\snapraid\snapraid.content
data d1 G:\array\
data d2 H:\array\
data d3 I:\array\
exclude Thumbs.db
exclude \$RECYCLE.BIN
exclude \System Volume Information
smartctl d1 -d sat %s
smartctl d2 -d usbjmicron %s
smartctl parity -d areca,1/1 /dev/arcmsr0
smartctl 2-parity -d areca,2/1 /dev/arcmsr0
PATTERN
Patterns are used to select a subset of files to exclude or include in the process.
There are four different types of patterns:
FILE Selects any file named FILE. You can use any globbing characters like * and ?, and character
classes like [a-z]. This pattern applies only to files, not directories.
DIR/ Selects any directory named DIR and everything inside. You can use any globbing characters like *
and ?. This pattern applies only to directories, not files.
/PATH/FILE
Selects the exact specified file path. You can use any globbing characters like * and ?, but they
never match a directory slash. This pattern applies only to files, not directories.
/PATH/DIR/
Selects the exact specified directory path and everything inside. You can use any globbing
characters like * and ?, but they never match a directory slash. This pattern applies only to
directories, not files.
When you specify an absolute path starting with /, it is applied at the array root directory, not the
local file system root directory.
In Windows, you can use the backslash \ instead of the forward slash /. Windows system directories,
junctions, mount points, and other Windows special directories are treated as files, meaning that to
exclude them, you must use a file rule, not a directory one.
If the file name contains a ´*´, ´?´, ´[´, or ´]´ character, you must escape it to avoid having it
interpreted as a globbing character. In Unix, the escape character is ´\´; in Windows, it is ´^´. When
the pattern is on the command line, you must double the escape character to avoid having it interpreted
by the command shell.
In the configuration file, you can use different strategies to filter the files to process. The simplest
approach is to use only "exclude" rules to remove all the files and directories you do not want to
process. For example:
# Excludes any file named "*.unrecoverable"
exclude *.unrecoverable
# Excludes the root directory "/lost+found"
exclude /lost+found/
# Excludes any subdirectory named "tmp"
exclude tmp/
The opposite approach is to define only the files you want to process, using only "include" rules. For
example:
# Includes only some directories
include /movies/
include /musics/
include /pictures/
The final approach is to mix "exclude" and "include" rules. In this case, the order of rules is
important. Earlier rules take precedence over later ones. To simplify, you can list all the "exclude"
rules first and then all the "include" rules. For example:
# Excludes any file named "*.unrecoverable"
exclude *.unrecoverable
# Excludes any subdirectory named "tmp"
exclude tmp/
# Includes only some directories
include /movies/
include /musics/
include /pictures/
On the command line, using the -f option, you can only use "include" patterns. For example:
# Checks only the .mp3 files.
# In Unix, use quotes to avoid globbing expansion by the shell.
snapraid -f "*.mp3" check
In Unix, when using globbing characters on the command line, you must quote them to prevent the shell
from expanding them.
CONTENT
SnapRAID stores the list and checksums of your files in the content file.
It is a binary file that lists all the files present in your disk array, along with all the checksums to
verify their integrity.
This file is read and written by the "sync" and "scrub" commands and read by the "fix", "check", and
"status" commands.
PARITY
SnapRAID stores the parity information of your array in the parity files.
These are binary files containing the computed parity of all the blocks defined in the "content" file.
These files are read and written by the "sync" and "fix" commands and only read by the "scrub" and
"check" commands.
ENCODING
SnapRAID in Unix ignores any encoding. It reads and stores the file names with the same encoding used by
the file system.
In Windows, all names read from the file system are converted and processed in UTF-8 format.
To have file names printed correctly, you must set the Windows console to UTF-8 mode with the command
"chcp 65001" and use a TrueType font like "Lucida Console" as the console font. This affects only the
printed file names; if you redirect the console output to a file, the resulting file is always in UTF-8
format.
COPYRIGHT
This file is Copyright (C) 2025 Andrea Mazzoleni
SEE ALSO
rsync(1)
SnapRAID Backup for Disk Arrays(1)