Ubuntu Manpage: pic - compile pictures for troff or TeX

NAME

       pic - compile pictures for troff or TeX

SYNOPSIS

       pic [ -nvCSU ] [ filename ... ]
       pic -t [ -cvzCSU ] [ filename ... ]

DESCRIPTION

       This manual page describes the GNU version of pic, which is part of the groff document formatting system.
       pic  compiles  descriptions  of  pictures embedded within troff or TeX input files into commands that are
       understood by TeX or troff.  Each picture starts with a line beginning with .PS  and  ends  with  a  line
       beginning with .PE.  Anything outside of .PS and .PE is passed through without change.

       It  is  the  user's  responsibility to provide appropriate definitions of the PS and PE macros.  When the
       macro package being used does not supply such definitions (for example, old versions of -ms), appropriate
       definitions can be obtained with -mpic: These will center each picture.

OPTIONS

Options that do not take arguments may be grouped behind a single -. The special option -- can be used
to mark the end of the options. A filename of - refers to the standard input.

-C Recognize .PS and .PE even when followed by a character other than space or newline.

-S Safer mode; do not execute sh commands. This can be useful when operating on untrustworthy input.
(enabled by default)

-U Unsafe mode; revert the default option -S.

-n Don't use the groff extensions to the troff drawing commands. You should use this if you are
using a postprocessor that doesn't support these extensions. The extensions are described in
groff_out(5). The -n option also causes pic not to use zero-length lines to draw dots in troff
mode.

-t TeX mode.

-c Be more compatible with tpic. Implies -t. Lines beginning with \ are not passed through
transparently. Lines beginning with . are passed through with the initial . changed to \. A
line beginning with .ps is given special treatment: it takes an optional integer argument
specifying the line thickness (pen size) in milliinches; a missing argument restores the previous
line thickness; the default line thickness is 8 milliinches. The line thickness thus specified
takes effect only when a non-negative line thickness has not been specified by use of the
thickness attribute or by setting the linethick variable.

-v Print the version number.

-z In TeX mode draw dots using zero-length lines.

The following options supported by other versions of pic are ignored:

-D Draw all lines using the \D escape sequence. pic always does this.

-T dev Generate output for the troff device dev. This is unnecessary because the troff output generated
by pic is device-independent.

USAGE

This section describes only the differences between GNU pic and the original version of pic. Many of
these differences also apply to newer versions of Unix pic. A complete documentation is available in the
file

/usr/share/doc/groff-base/pic.ms.gz

TeX mode
TeX mode is enabled by the -t option. In TeX mode, pic will define a vbox called \graph for each
picture. Use the figname command to change the name of the vbox. You must yourself print that vbox
using, for example, the command

\centerline{\box\graph}

Actually, since the vbox has a height of zero (it is defined with \vtop) this will produce slightly more
vertical space above the picture than below it;

\centerline{\raise 1em\box\graph}

would avoid this.

To make the vbox having a positive height and a depth of zero (as used e.g. by LaTeX's graphics.sty),
define the following macro in your document:

\def\gpicbox#1{%
\vbox{\unvbox\csname #1\endcsname\kern 0pt}}

Now you can simply say \gpicbox{graph} instead of \box\graph.

You must use a TeX driver that supports the tpic specials, version 2.

Lines beginning with \ are passed through transparently; a % is added to the end of the line to avoid
unwanted spaces. You can safely use this feature to change fonts or to change the value of
\baselineskip. Anything else may well produce undesirable results; use at your own risk. Lines
beginning with a period are not given any special treatment.

Commands
for variable = expr1 to expr2 [by [*]expr3] do X body X
Set variable to expr1. While the value of variable is less than or equal to expr2, do body and
increment variable by expr3; if by is not given, increment variable by 1. If expr3 is prefixed by
* then variable will instead be multiplied by expr3. The value of expr3 can be negative for the
additive case; variable is then tested whether it is greater than or equal to expr2. For the
multiplicative case, expr3 must be greater than zero. If the constraints aren't met, the loop
isn't executed. X can be any character not occurring in body.

if expr then X if-true X [else Y if-false Y]
Evaluate expr; if it is non-zero then do if-true, otherwise do if-false. X can be any character
not occurring in if-true. Y can be any character not occurring in if-false.

print arg...
Concatenate the arguments and print as a line on stderr. Each arg must be an expression, a
position, or text. This is useful for debugging.

command arg...
Concatenate the arguments and pass them through as a line to troff or TeX. Each arg must be an
expression, a position, or text. This has a similar effect to a line beginning with . or \, but
allows the values of variables to be passed through. For example,

.PS
x = 14
command ".ds string x is " x "."
.PE
\*[string]

prints

x is 14.

sh X command X
Pass command to a shell. X can be any character not occurring in command.

copy "filename"
Include filename at this point in the file.

copy ["filename"] thru X body X [until "word"]
copy ["filename"] thru macro [until "word"]
This construct does body once for each line of filename; the line is split into blank-delimited
words, and occurrences of $i in body, for i between 1 and 9, are replaced by the i-th word of the
line. If filename is not given, lines are taken from the current input up to .PE. If an until
clause is specified, lines will be read only until a line the first word of which is word; that
line will then be discarded. X can be any character not occurring in body. For example,

.PS
copy thru % circle at ($1,$2) % until "END"
1 2
3 4
5 6
END
box
.PE

is equivalent to

.PS
circle at (1,2)
circle at (3,4)
circle at (5,6)
box
.PE

The commands to be performed for each line can also be taken from a macro defined earlier by
giving the name of the macro as the argument to thru.

reset
reset variable1[,] variable2 ...
Reset pre-defined variables variable1, variable2 ... to their default values. If no arguments are
given, reset all pre-defined variables to their default values. Note that assigning a value to
scale also causes all pre-defined variables that control dimensions to be reset to their default
values times the new value of scale.

plot expr ["text"]
This is a text object which is constructed by using text as a format string for sprintf with an
argument of expr. If text is omitted a format string of "%g" is used. Attributes can be
specified in the same way as for a normal text object. Be very careful that you specify an
appropriate format string; pic does only very limited checking of the string. This is deprecated
in favour of sprintf.

variable := expr
This is similar to = except variable must already be defined, and expr will be assigned to
variable without creating a variable local to the current block. (By contrast, = defines the
variable in the current block if it is not already defined there, and then changes the value in
the current block only.) For example, the following:

.PS
x = 3
y = 3
[
x := 5
y = 5
]
print x " " y
.PE

prints

5 3

Arguments of the form

X anything X

are also allowed to be of the form

{ anything }

In this case anything can contain balanced occurrences of { and }. Strings may contain X or imbalanced
occurrences of { and }.

Expressions
The syntax for expressions has been significantly extended:

x ^ y (exponentiation)
sin(x)
cos(x)
atan2(y, x)
log(x) (base 10)
exp(x) (base 10, ie 10^x)
sqrt(x)
int(x)
rand() (return a random number between 0 and 1)
rand(x) (return a random number between 1 and x; deprecated)
srand(x) (set the random number seed)
max(e1, e2)
min(e1, e2)
!e
e1 && e2
e1 || e2
e1 == e2
e1 != e2
e1 >= e2
e1 > e2
e1 <= e2
e1 < e2
"str1" == "str2"
"str1" != "str2"

String comparison expressions must be parenthesised in some contexts to avoid ambiguity.

Other Changes
A bare expression, expr, is acceptable as an attribute; it is equivalent to dir expr, where dir is the
current direction. For example

line 2i

means draw a line 2 inches long in the current direction. The `i' (or `I') character is ignored; to use
another measurement unit, set the scale variable to an appropriate value.

The maximum width and height of the picture are taken from the variables maxpswid and maxpsht. Initially
these have values 8.5 and 11.

Scientific notation is allowed for numbers. For example

x = 5e-2

Text attributes can be compounded. For example,

"foo" above ljust

is valid.

There is no limit to the depth to which blocks can be examined. For example,

[A: [B: [C: box ]]] with .A.B.C.sw at 1,2
circle at last [].A.B.C

is acceptable.

Arcs now have compass points determined by the circle of which the arc is a part.

Circles, ellipses, and arcs can be dotted or dashed. In TeX mode splines can be dotted or dashed also.

Boxes can have rounded corners. The rad attribute specifies the radius of the quarter-circles at each
corner. If no rad or diam attribute is given, a radius of boxrad is used. Initially, boxrad has a value
of 0. A box with rounded corners can be dotted or dashed.

Boxes can have slanted sides. This effectively changes the shape of a box from a rectangle to an
arbitrary parallelogram. The xslanted and yslanted attributes specify the x and y offset of the box's
upper right corner from its default position.

The .PS line can have a second argument specifying a maximum height for the picture. If the width of
zero is specified the width will be ignored in computing the scaling factor for the picture. Note that
GNU pic will always scale a picture by the same amount vertically as well as horizontally. This is
different from the DWB 2.0 pic which may scale a picture by a different amount vertically than
horizontally if a height is specified.

Each text object has an invisible box associated with it. The compass points of a text object are
determined by this box. The implicit motion associated with the object is also determined by this box.
The dimensions of this box are taken from the width and height attributes; if the width attribute is not
supplied then the width will be taken to be textwid; if the height attribute is not supplied then the
height will be taken to be the number of text strings associated with the object times textht. Initially
textwid and textht have a value of 0.

In (almost all) places where a quoted text string can be used, an expression of the form

sprintf("format", arg,...)

can also be used; this will produce the arguments formatted according to format, which should be a string
as described in printf(3) appropriate for the number of arguments supplied.

The thickness of the lines used to draw objects is controlled by the linethick variable. This gives the
thickness of lines in points. A negative value means use the default thickness: in TeX output mode, this
means use a thickness of 8 milliinches; in TeX output mode with the -c option, this means use the line
thickness specified by .ps lines; in troff output mode, this means use a thickness proportional to the
pointsize. A zero value means draw the thinnest possible line supported by the output device. Initially
it has a value of -1. There is also a thick[ness] attribute. For example,

circle thickness 1.5

would draw a circle using a line with a thickness of 1.5 points. The thickness of lines is not affected
by the value of the scale variable, nor by the width or height given in the .PS line.

Boxes (including boxes with rounded corners or slanted sides), circles and ellipses can be filled by
giving them an attribute of fill[ed]. This takes an optional argument of an expression with a value
between 0 and 1; 0 will fill it with white, 1 with black, values in between with a proportionally gray
shade. A value greater than 1 can also be used: this means fill with the shade of gray that is currently
being used for text and lines. Normally this will be black, but output devices may provide a mechanism
for changing this. Without an argument, then the value of the variable fillval will be used. Initially
this has a value of 0.5. The invisible attribute does not affect the filling of objects. Any text
associated with a filled object will be added after the object has been filled, so that the text will not
be obscured by the filling.

Three additional modifiers are available to specify colored objects: outline[d] sets the color of the
outline, shaded the fill color, and colo[u]r[ed] sets both. All three keywords expect a suffix
specifying the color, for example

circle shaded "green" outline "black"

Currently, color support isn't available in TeX mode. Predefined color names for groff are in the device
macro files, for example ps.tmac; additional colors can be defined with the .defcolor request (see the
manual page of troff(1) for more details).

To change the name of the vbox in TeX mode, set the pseudo-variable figname (which is actually a
specially parsed command) within a picture. Example:

.PS
figname = foobar;
...
.PE

The picture is then available in the box \foobar.

pic assumes that at the beginning of a picture both glyph and fill color are set to the default value.

Arrow heads will be drawn as solid triangles if the variable arrowhead is non-zero and either TeX mode is
enabled or the -n option has not been given. Initially arrowhead has a value of 1. Note that solid
arrow heads are always filled with the current outline color.

The troff output of pic is device-independent. The -T option is therefore redundant. All numbers are
taken to be in inches; numbers are never interpreted to be in troff machine units.

Objects can have an aligned attribute. This will only work if the postprocessor is grops, or gropdf.
Any text associated with an object having the aligned attribute will be rotated about the center of the
object so that it is aligned in the direction from the start point to the end point of the object. Note
that this attribute will have no effect for objects whose start and end points are coincident.

In places where nth is allowed `expr'th is also allowed. Note that 'th is a single token: no space is
allowed between the ' and the th. For example,

for i = 1 to 4 do {
line from `i'th box.nw to `i+1'th box.se
}

CONVERSION

       To  obtain  a  stand-alone picture from a pic file, enclose your pic code with .PS and .PE requests; roff
       configuration commands may be added at the beginning of the file, but no roff text.

       It is necessary to feed this file into groff without adding any page information, so you must check which
       .PS and .PE requests are actually called.  For example, the mm macro package adds a page number, which is
       very annoying.  At the moment, calling standard groff without any macro  package  works.   Alternatively,
       you can define your own requests, e.g. to do nothing:

              .de PS
              ..
              .de PE
              ..

       groff  itself does not provide direct conversion into other graphics file formats.  But there are lots of
       possibilities if you first transform your picture into PostScript® format using the  groff  option  -Tps.
       Since  this ps-file lacks BoundingBox information it is not very useful by itself, but it may be fed into
       other conversion programs, usually named ps2other or pstoother or the  like.   Moreover,  the  PostScript
       interpreter ghostscript (gs) has built-in graphics conversion devices that are called with the option

              gs -sDEVICE=<devname>

       Call

              gs --help

       for a list of the available devices.

       An  alternative  may  be  to  use the -Tpdf option to convert your picture directly into PDF format.  The
       MediaBox of the file produced can be controlled by passing a -P-p papersize to groff.

       As the Encapsulated PostScript File Format EPS is getting more and more  important,  and  the  conversion
       wasn't regarded trivial in the past you might be interested to know that there is a conversion tool named
       ps2eps which does the right job.  It is much better than the tool ps2epsi packaged with gs.

       For  bitmapped graphic formats, you should use pstopnm; the resulting (intermediate) PNM file can be then
       converted to virtually any graphics format using the tools of the netpbm package .

FILES

       /usr/share/groff/1.22.2/tmac/pic.tmac   Example definitions of the PS and PE macros.

BUGS

       Input characters that are invalid for groff (i.e., those with ASCII code 0, or 013 octal, or between  015
       and 037 octal, or between 0200 and 0237 octal) are rejected even in TeX mode.

       The  interpretation  of  fillval is incompatible with the pic in 10th edition Unix, which interprets 0 as
       black and 1 as white.

       PostScript® is a registered trademark of Adobe Systems Incorporation.

Groff Version 1.22.2                             22 January 2014                                          PIC(1)