NAME

       uaputl - configure Marvell uAP wireless driver

SYNOPSIS

       uaputl [options] <command> [parameters]

DESCRIPTION

       This  manual  page  documents  briefly  the uaputl command, which is used to configure the
       device driver for Marvell's uAP wireless interface.

OPTIONS

       -d <debug_level>
              Enable debugging output, level can be 0, 1, or 2.

       -h, --help
              Show summary of options and commands.

       -i <interface>
              Select interface to configure.

       -v     Show version of program.

COMMANDS

       For more information on the usage of each command use:
               uaputl.exe <command> --help

       sys_config
              Set/get uAP's profile

       sys_info
              Display system info

       sys_reset
              Reset uAP

       bss_start
              Start the BSS

       bss_stop
              Stop the BSS

       sta_deauth
              Deauth client

       sta_list
              Display list of clients

       sys_cfg_ap_mac_address
              Set/get uAP mac address

       sys_cfg_ssid
              Set/get uAP ssid

       sys_cfg_beacon_period
              Set/get uAP beacon period

       sys_cfg_dtim_period
              Set/get uAP dtim period

       sys_cfg_channel
              Set/get uAP radio channel

       sys_cfg_scan_channels
              Set/get uAP radio channel list

       sys_cfg_rates
              Set/get uAP rates

       sys_cfg_rates_ext
              Set/get uAP rates (extended)

       sys_cfg_tx_power
              Set/get uAP tx power

       sys_cfg_bcast_ssid_ctl
              Set/get uAP broadcast ssid

       sys_cfg_preamble_ctl
              Get uAP preamble

       sys_cfg_antenna_ctl
              Set/get uAP tx/rx antenna

       sys_cfg_rts_threshold
              Set/get uAP rts threshold

       sys_cfg_frag_threshold
              Set/get uAP frag threshold

       sys_cfg_radio_ctl
              Set/get uAP radio on/off

       sys_cfg_tx_data_rate
              Set/get uAP tx rate

       sys_cfg_mcbc_data_rate
              Set/get uAP MCBC rate

       sys_cfg_rsn_replay_prot
              Set/get RSN replay protection

       sys_cfg_pkt_fwd_ctl
              Set/get uAP packet forwarding

       sys_cfg_sta_ageout_timer
              Set/get station ageout timer

       sys_cfg_auth
              Set/get uAP authentication mode

       sys_cfg_protocol
              Set/get uAP security protocol

       sys_cfg_wep_key
              Set/get uAP wep key

       sys_cfg_cipher
              Set/get uAP WPA/WPA cipher

       sys_cfg_wpa_passphrase
              Set/get uAP WPA or WPA2 passphrase

       sys_cfg_group_rekey_timer
              Set/get uAP group re-key time

       sys_cfg_max_sta_num
              Set/get uAP max station number

       sys_cfg_retry_limit
              Set/get uAP retry limit number

       sys_cfg_custom_ie
              Set/get custom IE configuration

       sta_filter_table
              Set/get uAP mac filter

       regrdwr
              Read/Write register command

       memaccess
              Read/Write to a memory address command

       rdeeprom
              Read EEPROM

       cfg_data
              Get/Set configuration file from/to firmware

       sys_debug
              Set/Get debug parameter

       sys_cfg_80211d
              Set/Get 802.11D info

       uap_stats
              Get uAP stats

       powermode
              Set/get uAP power mode

       coex_config
              Set/get uAP BT coex configuration

SEE ALSO

       uapevent(1).

       This manual page was written by Bdale Garbee <bdale@gag.com>, for the Debian project  (and
       may be used by others).

                                          July 20, 2011                                 UAPUTL(1)