Provided by: libncarg-dev_6.1.2-7_amd64 
NAME
CONOP3 - sets option switches and specifys various REAL parameters to be used by the
Conran_family utility.
SYNOPSIS
CALL CONOP3 (IOPT, ARRAY, LENA)
DESCRIPTION
IOPT Character, input -- Selects an internal parameter and sets an option switch.
The possibilities are:
'CHL=ON' or 'CHL=OFF'
'CIL=ON' or 'CIL=OFF'
'CON=ON' or 'CON=OFF'
'DBP=ON' or 'DBP=OFF'
'SDC=ON' or 'SDC=OFF'
'SLD=ON' or 'SLD=OFF'
'TEN=ON' or 'TEN=OFF'
ARRAY Real array, input -- Sets an internal parameter.
LENA Integer, input -- The length of array ARRAY.
If an option is turned 'ON', then the remaining CONOP3 arguments can be used
to override the default settings of that option.
If the option is 'OFF', then the remaining arguments of the CONOP3 call can be
any dummy values. Option settings will be returned to their default values.
The following options are defined by this subroutine:
CHL This parameter determines how the high and low contour values are set. These
contour values may be set by the program or by the user. If CHL=OFF, the program
examines the user's input data and determines both the high and low values. If
CHL=ON, the user must specify the desired high (HI) and low (FLO) values. The
default is CHL=OFF.
If program set: CALL CONOP3('CHL=OFF',0.,0)
If user set: CALL CONOP3('CHL=ON',ARRAY,2) where ARRAY(1)=HI, ARRAY(2)=FLO
Note: The values supplied for contour increment and contour high and low values
assume unscaled data values. See the SDC parameter, below.
CIL This parameter determines how the contour increment (CINC) is set. The increment
is either calculated by the program (CIL=OFF) using the range of high and low
values from the user's input data, or set by the user (CIL=ON). The default is
CIL=OFF.
If program set: CALL CONOP3('CIL=OFF',0.,0)
If user set: CALL CONOP3('CIL=ON',CINC,1)
Note: By default, ('CIL=OFF') the program will examine the user's input data and
determine the contour interval (CINC) at some appropriate range between the level
of high and low values supplied, usually generating between 15 and 20 contour
levels.
Example: CALL CONOP3('CIL=ON',10.,1)
will generate contours at increments of 10. units in user coordinates.
CON This parameter determines how the contour levels are set. If CON=ON, the user
must specify an array of contour values and the number of contour levels. A
maximum of NCL=30 contour levels is permitted. If CON=OFF, NCL and the contour
values are computed. The default is OFF.
If program set: CALL CONOP3('CON=OFF',0.,0)
If user set: CALL CONOP3('CON=ON',ARRAY,NCL)
Note: The real array (ARRAY) must have the contour levels ordered from smallest to
largest.
Warning: It is illegal to use the CON option when either CIL or CHL are activated.
If this is done, the option call that detected the error will not be executed.
DBP This parameter determines how the dash pattern break point (BP) is set. (Does not
apply to entry CONRAQ.) If DBP=ON, BP must be set by the user. If DBP=OFF, the
program will set BP to 0. This is the default.
If program set: CALL CONOP3('DBP=OFF',0.,0)
If user set: CALL CONOP3('DBP=ON',BP,1)
Note: BP is a floating point number where the break for GTR and LSS contour dash
patterns are defined. BP is assumed to be given relative to the untransformed
contours.
To see how various dash line patterns can be assigned to various contours see
parameter DBP in "man conop4".
SDC The parameter to determine how to scale the input data from which the contours are
generated. (Does not apply to entry CONRAQ.) If SDC=ON, the scaling factor is
set to ARRAY(1). If SDC=OFF, the default scale factor of 1. is used.
If program set: CALL CONOP3('SDC=OFF',0.,0)
If user set: CALL CONOP3('SDC=ON',ARRAY,1)
Note: The data plotted on contour lines and the data plotted for relative minimums
and maximums will be scaled by ARRAY.
SLD Input a polygon to define the extent of area to be contoured. (Does not apply to
entry CONRAQ.) When this option is activated, only those contours within the
shield are drawn. The shield is a polygon specified by the user which must be
given in the same coordinate range as the the data. It must define only one
polygon.
To input a shield:
CALL CONOP3('SLD=ON',ARRAY,LENA)
Otherwise:
CALL CONOP3('SLD=OFF',0.,0)
Note: ARRAY is a real array LENA elements long. The first LENA/2 elements are X
coordinates and the second LENA/2 elements are Y coordinates. This polygon must
be closed, that is the first and last points in ARRAY must be the same.
Example:
DIMENSION SHLD(10)
DATA SHLD/ 7.,10.,10.,7.,7.,
1 7.,7.,10.,10.,7./
CALL CONOP3 ('SLD=ON',SHLD,10)
TEN The parameter to determine the tension factor applied when smoothing contour lines
using splines under tension. (Does not apply to entry CONRAQ.) If user set, the
allowed range is from greater than zero to 30. The higher the tension the less
smoothing occurs. The default value (TEN=OFF) is 2.5.
If program set: CALL CONOP3('TEN=OFF',0.,0)
If user set: CALL CONOP3('TEN=ON',TENS,1)
Note: This option is not available in the standard version of CONRAN.
USAGE
CONOP3 is called to set parameters of type REAL before CONRAN, CONRAQ, or CONRAS are
called to generate the contour plot.
EXAMPLES
Use the command ncargex to see the following examples: tconaq, tconan, and tconas.
ACCESS
To use CONOP3 load the NCAR Graphics libraries ncarg, ncarg_gks, and ncarg_c, preferably
in that order.
MESSAGES
See the conran_family man page for a description of all Conran_family error messages
and/or informational messages.
SEE ALSO
Online: conran_family, conran_family_params, conran, conraq, conras, conop1, conop2,
conop4, conpack, conpack_params
Hardcopy: NCAR Graphics Contouring and Mapping Tutorial; NCAR Graphics Fundamentals, UNIX
Version; User's Guide for NCAR GKS-0A Graphics
COPYRIGHT
Copyright (C) 1987-2009
University Corporation for Atmospheric Research
The use of this Software is governed by a License Agreement.