NAME

       sort - perl pragma to control sort() behaviour

SYNOPSIS

           use sort 'stable';          # guarantee stability
           use sort '_quicksort';      # use a quicksort algorithm
           use sort '_mergesort';      # use a mergesort algorithm
           use sort 'defaults';        # revert to default behavior
           no  sort 'stable';          # stability not important

           use sort '_qsort';          # alias for quicksort

           my $current;
           BEGIN {
               $current = sort::current();     # identify prevailing algorithm
           }

DESCRIPTION

       With the "sort" pragma you can control the behaviour of the builtin "sort()" function.

       In Perl versions 5.6 and earlier the quicksort algorithm was used to implement "sort()",
       but in Perl 5.8 a mergesort algorithm was also made available, mainly to guarantee worst
       case O(N log N) behaviour: the worst case of quicksort is O(N**2).  In Perl 5.8 and later,
       quicksort defends against quadratic behaviour by shuffling large arrays before sorting.

       A stable sort means that for records that compare equal, the original input ordering is
       preserved.  Mergesort is stable, quicksort is not.  Stability will matter only if elements
       that compare equal can be distinguished in some other way.  That means that simple
       numerical and lexical sorts do not profit from stability, since equal elements are
       indistinguishable.  However, with a comparison such as

          { substr($a, 0, 3) cmp substr($b, 0, 3) }

       stability might matter because elements that compare equal on the first 3 characters may
       be distinguished based on subsequent characters.  In Perl 5.8 and later, quicksort can be
       stabilized, but doing so will add overhead, so it should only be done if it matters.

       The best algorithm depends on many things.  On average, mergesort does fewer comparisons
       than quicksort, so it may be better when complicated comparison routines are used.
       Mergesort also takes advantage of pre-existing order, so it would be favored for using
       "sort()" to merge several sorted arrays.  On the other hand, quicksort is often faster for
       small arrays, and on arrays of a few distinct values, repeated many times.  You can force
       the choice of algorithm with this pragma, but this feels heavy-handed, so the subpragmas
       beginning with a "_" may not persist beyond Perl 5.8.  The default algorithm is mergesort,
       which will be stable even if you do not explicitly demand it.  But the stability of the
       default sort is a side-effect that could change in later versions.  If stability is
       important, be sure to say so with a

         use sort 'stable';

       The "no sort" pragma doesn't forbid what follows, it just leaves the choice open.  Thus,
       after

         no sort qw(_mergesort stable);

       a mergesort, which happens to be stable, will be employed anyway.  Note that

         no sort "_quicksort";
         no sort "_mergesort";

       have exactly the same effect, leaving the choice of sort algorithm open.

CAVEATS

       As of Perl 5.10, this pragma is lexically scoped and takes effect at compile time. In
       earlier versions its effect was global and took effect at run-time; the documentation
       suggested using "eval()" to change the behaviour:

         { eval 'use sort qw(defaults _quicksort)'; # force quicksort
           eval 'no sort "stable"';      # stability not wanted
           print sort::current . "\n";
           @a = sort @b;
           eval 'use sort "defaults"';   # clean up, for others
         }
         { eval 'use sort qw(defaults stable)';     # force stability
           print sort::current . "\n";
           @c = sort @d;
           eval 'use sort "defaults"';   # clean up, for others
         }

       Such code no longer has the desired effect, for two reasons.  Firstly, the use of "eval()"
       means that the sorting algorithm is not changed until runtime, by which time it's too late
       to have any effect. Secondly, "sort::current" is also called at run-time, when in fact the
       compile-time value of "sort::current" is the one that matters.

       So now this code would be written:

         { use sort qw(defaults _quicksort); # force quicksort
           no sort "stable";      # stability not wanted
           my $current;
           BEGIN { $current = sort::current; }
           print "$current\n";
           @a = sort @b;
           # Pragmas go out of scope at the end of the block
         }
         { use sort qw(defaults stable);     # force stability
           my $current;
           BEGIN { $current = sort::current; }
           print "$current\n";
           @c = sort @d;
         }