Provided by: freebsd-manpages_9.2+1-1_all 
NAME
if_bridge — network bridge device
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device if_bridge
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
if_bridge_load="YES"
bridgestp_load="YES"
DESCRIPTION
The if_bridge driver creates a logical link between two or more IEEE 802 networks that use the same (or
“similar enough”) framing format. For example, it is possible to bridge Ethernet and 802.11 networks
together, but it is not possible to bridge Ethernet and Token Ring together.
Each if_bridge interface is created at runtime using interface cloning. This is most easily done with
the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5).
The if_bridge interface randomly chooses a link (MAC) address in the range reserved for locally
administered addresses when it is created. This address is guaranteed to be unique only across all
if_bridge interfaces on the local machine. Thus you can theoretically have two bridges on the different
machines with the same link addresses. The address can be changed by assigning the desired link address
using ifconfig(8).
If sysctl(8) node net.link.bridge.inherit_mac has non-zero value, newly created bridge will inherit MAC
address from its first member instead of choosing random link-level address. This will provide more
predictable bridge MAC without any additional configuration, but currently this feature is known to break
some L2 protocols, for example PPPoE that is provided by ng_pppoe(4) and ppp(8). Now this feature is
considered as experimental and is turned off by-default.
A bridge can be used to provide several services, such as a simple 802.11-to-Ethernet bridge for wireless
hosts, and traffic isolation.
A bridge works like a switch, forwarding traffic from one interface to another. Multicast and broadcast
packets are always forwarded to all interfaces that are part of the bridge. For unicast traffic, the
bridge learns which MAC addresses are associated with which interfaces and will forward the traffic
selectively.
All the bridged member interfaces need to be up in order to pass network traffic. These can be enabled
using ifconfig(8) or ifconfig_⟨interface⟩="up" in rc.conf(5).
The MTU of the first member interface to be added is used as the bridge MTU. All additional members are
required to have exactly the same value.
The TXCSUM capability is disabled for any interface added to the bridge, and it is restored when the
interface is removed again.
The bridge supports “monitor mode”, where the packets are discarded after bpf(4) processing, and are not
processed or forwarded further. This can be used to multiplex the input of two or more interfaces into a
single bpf(4) stream. This is useful for reconstructing the traffic for network taps that transmit the
RX/TX signals out through two separate interfaces.
IPV6 SUPPORT
if_bridge supports the AF_INET6 address family on bridge interfaces. The following rc.conf(5) variable
configures an IPv6 link-local address on bridge0 interface:
ifconfig_bridge0_ipv6="up"
or in a more explicit manner:
ifconfig_bridge0_ipv6="inet6 auto_linklocal"
However, the AF_INET6 address family has a concept of scope zone. Bridging multiple interfaces change
the zone configuration because multiple links are merged to each other and form a new single link while
the member interfaces still work individually. This means each member interface still has a separate
link-local scope zone and the if_bridge interface has another single, aggregated link-local scope zone at
the same time. This situation is clearly against the description "zones of the same scope cannot
overlap" in Section 5, RFC 4007. Although it works in most cases, it can cause some conterintuitive or
undesirable behavior in some edge cases when both of the if_bridge interface and one of the member
interface have an IPv6 address and applications use both of them.
To prevent this situation, if_bridge checks whether a link-local scoped IPv6 address is configured on a
member interface to be added and the if_bridge interface. When the if_bridge interface has IPv6
addresses, IPv6 addresses on the member interface will be automatically removed before the interface is
added.
This behavior can be disabled by setting sysctl(8) variable net.link.bridge.allow_llz_overlap to 1.
Note that ACCEPT_RTADV and AUTO_LINKLOCAL interface flag are not enabled by default on if_bridge
interface even when net.inet6.ip6.accept_rtadv and/or net.inet6.ip6.auto_linklocal is set to 1.
SPANNING TREE
The if_bridge driver implements the Rapid Spanning Tree Protocol (RSTP or 802.1w) with backwards
compatibility with the legacy Spanning Tree Protocol (STP). Spanning Tree is used to detect and remove
loops in a network topology.
RSTP provides faster spanning tree convergence than legacy STP, the protocol will exchange information
with neighbouring switches to quickly transition to forwarding without creating loops.
The code will default to RSTP mode but will downgrade any port connected to a legacy STP network so is
fully backward compatible. A bridge can be forced to operate in STP mode without rapid state transitions
via the proto command in ifconfig(8).
The bridge can log STP port changes to syslog(3) by enabling the net.link.bridge.log_stp variable using
sysctl(8).
PACKET FILTERING
Packet filtering can be used with any firewall package that hooks in via the pfil(9) framework. When
filtering is enabled, bridged packets will pass through the filter inbound on the originating interface,
on the bridge interface and outbound on the appropriate interfaces. Either stage can be disabled. The
filtering behaviour can be controlled using sysctl(8):
net.link.bridge.pfil_onlyip Controls the handling of non-IP packets which are not passed to pfil(9).
Set to 1 to only allow IP packets to pass (subject to firewall rules), set
to 0 to unconditionally pass all non-IP Ethernet frames.
net.link.bridge.pfil_member Set to 1 to enable filtering on the incoming and outgoing member interfaces,
set to 0 to disable it.
net.link.bridge.pfil_bridge Set to 1 to enable filtering on the bridge interface, set to 0 to disable
it.
net.link.bridge.pfil_local_phys
Set to 1 to additionally filter on the physical interface for locally
destined packets. Set to 0 to disable this feature.
net.link.bridge.ipfw Set to 1 to enable layer2 filtering with ipfirewall(4), set to 0 to disable
it. This needs to be enabled for dummynet(4) support. When ipfw is
enabled, pfil_bridge and pfil_member will be disabled so that IPFW is not
run twice; these can be re-enabled if desired.
net.link.bridge.ipfw_arp Set to 1 to enable layer2 ARP filtering with ipfirewall(4), set to 0 to
disable it. Requires ipfw to be enabled.
ARP and REVARP packets are forwarded without being filtered and others that are not IP nor IPv6 packets
are not forwarded when pfil_onlyip is enabled. IPFW can filter Ethernet types using mac-type so all
packets are passed to the filter for processing.
The packets originating from the bridging host will be seen by the filter on the interface that is looked
up in the routing table.
The packets destined to the bridging host will be seen by the filter on the interface with the MAC
address equal to the packet's destination MAC. There are situations when some of the bridge members are
sharing the same MAC address (for example the vlan(4) interfaces: they are currently sharing the MAC
address of the parent physical interface). It is not possible to distinguish between these interfaces
using their MAC address, excluding the case when the packet's destination MAC address is equal to the MAC
address of the interface on which the packet was entered to the system. In this case the filter will see
the incoming packet on this interface. In all other cases the interface seen by the packet filter is
chosen from the list of bridge members with the same MAC address and the result strongly depends on the
member addition sequence and the actual implementation of if_bridge. It is not recommended to rely on
the order chosen by the current if_bridge implementation: it can be changed in the future.
The previous paragraph is best illustrated with the following pictures. Let
• the MAC address of the incoming packet's destination is nn:nn:nn:nn:nn:nn,
• the interface on which packet entered the system is ifX,
• ifX MAC address is xx:xx:xx:xx:xx:xx,
• there are possibly other bridge members with the same MAC address xx:xx:xx:xx:xx:xx,
• the bridge has more than one interface that are sharing the same MAC address yy:yy:yy:yy:yy:yy; we
will call them vlanY1, vlanY2, etc.
Then if the MAC address nn:nn:nn:nn:nn:nn is equal to the xx:xx:xx:xx:xx:xx then the filter will see the
packet on the interface ifX no matter if there are any other bridge members carrying the same MAC
address. But if the MAC address nn:nn:nn:nn:nn:nn is equal to the yy:yy:yy:yy:yy:yy then the interface
that will be seen by the filter is one of the vlanYn. It is not possible to predict the name of the
actual interface without the knowledge of the system state and the if_bridge implementation details.
This problem arises for any bridge members that are sharing the same MAC address, not only to the vlan(4)
ones: they we taken just as the example of such situation. So if one wants the filter the locally
destined packets based on their interface name, one should be aware of this implication. The described
situation will appear at least on the filtering bridges that are doing IP-forwarding; in some of such
cases it is better to assign the IP address only to the if_bridge interface and not to the bridge
members. Enabling net.link.bridge.pfil_local_phys will let you do the additional filtering on the
physical interface.
EXAMPLES
The following when placed in the file /etc/rc.conf will cause a bridge called “bridge0” to be created,
and will add the interfaces “wlan0” and “fxp0” to the bridge, and then enable packet forwarding. Such a
configuration could be used to implement a simple 802.11-to-Ethernet bridge (assuming the 802.11
interface is in ad-hoc mode).
cloned_interfaces="bridge0"
ifconfig_bridge0="addm wlan0 addm fxp0 up"
For the bridge to forward packets all member interfaces and the bridge need to be up. The above example
would also require:
create_args_wlan0="wlanmode hostap"
ifconfig_wlan0="up ssid my_ap mode 11g"
ifconfig_fxp0="up"
Consider a system with two 4-port Ethernet boards. The following will cause a bridge consisting of all 8
ports with Rapid Spanning Tree enabled to be created:
ifconfig bridge0 create
ifconfig bridge0 \
addm fxp0 stp fxp0 \
addm fxp1 stp fxp1 \
addm fxp2 stp fxp2 \
addm fxp3 stp fxp3 \
addm fxp4 stp fxp4 \
addm fxp5 stp fxp5 \
addm fxp6 stp fxp6 \
addm fxp7 stp fxp7 \
up
The bridge can be used as a regular host interface at the same time as bridging between its member ports.
In this example, the bridge connects em0 and em1, and will receive its IP address through DHCP:
cloned_interfaces="bridge0"
ifconfig_bridge0="addm em0 addm em1 DHCP"
ifconfig_em0="up"
ifconfig_em1="up"
The bridge can tunnel Ethernet across an IP internet using the EtherIP protocol. This can be combined
with ipsec(4) to provide an encrypted connection. Create a gif(4) interface and set the local and remote
IP addresses for the tunnel, these are reversed on the remote bridge.
ifconfig gif0 create
ifconfig gif0 tunnel 1.2.3.4 5.6.7.8 up
ifconfig bridge0 create
ifconfig bridge0 addm fxp0 addm gif0 up
Note that FreeBSD 6.1, 6.2, 6.3, 7.0, 7.1, and 7.2 have a bug in the EtherIP protocol. For more details
and workaround, see gif(4) manual page.
SEE ALSO
gif(4), ipf(4), ipfw(4), pf(4), ifconfig(8)
HISTORY
The if_bridge driver first appeared in FreeBSD 6.0.
AUTHORS
The bridge driver was originally written by Jason L. Wright ⟨jason@thought.net⟩ as part of an
undergraduate independent study at the University of North Carolina at Greensboro.
This version of the if_bridge driver has been heavily modified from the original version by Jason R.
Thorpe ⟨thorpej@wasabisystems.com⟩.
Rapid Spanning Tree Protocol (RSTP) support was added by Andrew Thompson ⟨thompsa@FreeBSD.org⟩.
BUGS
The if_bridge driver currently supports only Ethernet and Ethernet-like (e.g., 802.11) network devices,
with exactly the same interface MTU size as the bridge device.
Debian July 27, 2013 IF_BRIDGE(4)