Provided by: ax25-tools_0.0.10-rc2+cvs20120204-3ubuntu1_amd64 
NAME
ax25d.conf - ax25d configuration file.
DESCRIPTION
Ax25d.conf controls the functioning of ax25d. Its purpose is to specify on which ports to
listen on, which applications are available, and to whom they are available to. The
configuration file is common to both AX.25, NET/ROM and Rose and their is similarity
between the two parts of the file.
The general layout for an entry for a given port is as follows:
interface control
callsign entry 1
.
.
callsign entry n
The interface control line determines which port and callsigns apply to the following
callsign entry lines, until the next interface control is read. There are four different
variants of the interface control line:
1. [AX.25 Port Name]
2. [Callsign VIA AX.25 Port Name]
3. <NET/ROM Port Name>
4. {Callsign VIA Rose Port Name}
Version 1 allows the following callsign entry lines to listen on the AX.25 port specified
by the AX.25 port name using the default callsign of that AX.25 port.
Version 2 allows the following callsign entry lines to listen on the AX.25 port specified
by the AX.25 port name using the callsign specified instead of the default callsign of
that AX.25 port. Specifying a * for the AX.25 port name allows the following callsign
entries to be valid for all the operating AX.25 ports using the callsign specified. VIA
can be abbreviated to just V. If the callsign has an asterisk appended to it then the
system will be listening on the port with the callsign, but as a pseudo-digipeater instead
of being the normal destination callsign.
Version 3 allows the following callsign entry lines to listen on the NET/ROM port
specified by the NET/ROM port name using the default callsign of that NET/ROM port.
Version 4 allows the following callsign entry lines to listen on the Rose port using the
specified Rose port name using the callsign specified as the service access point (SAP). A
* may be specified for a callsign to allow matching to any incoming Call Requests with any
SAP.
The callsign entry lines have a similar layout for both AX.25, NET/ROM and Rose, the
layout is:
peer window t1 t2 t3 idle n2 mode uid exec args...
All values must be entered for all entries even when they are not used (ie window for
NET/ROM, just enter a * instead), The meanings of each of the fields is given below. All
timings apart from the idle value are given in seconds, the idle values is given in
minutes.
peer This specifies the callsign of the remote end of the connection that
should have the following parameters and executable set up for them. The
syntax of the peer argument is explained below.
window This sets the the value of the window size, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used. This entry is used by AX.25 but not by NET/ROM or
Rose.
t1 This sets the the value of the T1 timer, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used. This entry is used by both AX.25 and NET/ROM but
not by Rose.
t2 This sets the the value of the T2 timer, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used. This entry is used by both AX.25 and NET/ROM but
not by Rose.
t3 This sets the the value of the T3 timer, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used. This entry is used by AX.25 but not by NET/ROM or
Rose.
idle This sets the the value of the idle timer, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used.
n2 This sets the the value of the N2 counter, if a value of * is entered in
this field then the default value for the port is taken from the
“parameters” entry (see below) or lacking such an entry, the kernel
default value is used. This entry is used by both AX.25 and NET/ROM but
not by Rose.
mode This is a set of flags that control the various properties associated
with the incoming connection. The flags are single letters, may be in
either upper or lower case, and there may not be any spaces between them.
If no flags are to be specified either a 0, - or a * must be entered
instead. The valid mode flag letters are:
D Do not allow connections that have passed via any digipeaters. AX.25
only.
L Do not allow this station to connect, they are Locked out.
N Check that the NET/ROM neighbour is allowed, currently unused.
Q Do not make an entry into the log file for this connection.
V Validate the callsign of the incoming connection, currently unused.
uid This is the userid that the following command should run under when
executing.
exec This is the executable that should be executed when an incoming
connection matches the criteria of both the interface control and the
callsign entry .
args... These are the optional arguments that are passed to the executable. All
of the arguments are passed literally apart from the following:
%d The name of the port that the connection is on.
%U The username (callsign) of the remote station in upper case without
the SSID.
%u The username (callsign) of the remote station in lower case without
the SSID.
%S The username (callsign) of the remote station in upper case with the
SSID.
%s The username (callsign) of the remote station in lower case with the
SSID.
%P The nodename of the remote station in upper case without the SSID.
This is only valid under NET/ROM and Rose, under AX.25 a % is
substituted instead.
%p The nodename of the remote station in lower case without the SSID.
This is only valid under NET/ROM and Rose, under AX.25 a % is
substituted instead.
%R The nodename of the remote station in upper case with the SSID.
This is only valid under NET/ROM and Rose, under AX.25 a % is
substituted instead.
%r The nodename of the remote station in lower case with the SSID.
This is only valid under NET/ROM and Rose, under AX.25 a % is
substituted instead.
%% A %.
The peer argument is dependant upon whether AX.25, NET/ROM or Rose is being used. There
are five formats of this argument:
1. default
2. parameters
3. callsign
4. callsign@node
5. @node
The first version is used by AX.25, NET/ROM and Rose to specify that all callsigns on a
given port are to be matched. The default line is usually the last of the callsign entry
lines, so that more specific entries may have the chance to be matched first.
The second version is not a callsign entry that is used by any incoming connections. It is
a means to specify default values for parameters such as Window, T1, T2, T3, Idle and N2.
It is used for both AX.25, NET/ROM and Rose.
The third version is used by both AX.25, NET/ROM and Rose to specify the callsign of the
remote station to match the callsign entry line. If no SSID is specified then the callsign
will be matched with any that has the same callsign and any SSID. Specifying an SSID
causes the callsign to be matched exactly. In the case of NET/ROM and Rose this entry does
not specify which node the originating callsign comes from.
The fourth version is used by NET/ROM and Rose to specify the callsign of the remote
station and the remote node to match the callsign entry line. If no SSID is specified in
the callsign section then the callsign will be matched with any that has the same callsign
and any SSID. Specifying an SSID causes the callsign to be matched exactly.
The fifth version is used by NET/ROM and Rose to specify only the address of the remote
node to match the callsign entry line. This entry will mean that all remote users at the
given node will match the entry.
Comments may be embedded in the configuration file by placing a # in the first column.
ax25d can now honour AX.25 TCP/IP mode-VC connections in a special way. Therefore, a new
port specific option "parameters_extAX25" is available, with the following options, which
are seperated by space.
parameters_extAX25
VC-debug
VC-reject-login|VC-wait-login|VC-login-ok
VC-disc-on-linkfailure-msg, VC-send-failure-msg, VC-log-connections
Recommended settings in ax25d.conf:
parameters_extAX25 VC-wait-login VC-disc-on-linkfailure-msg VC-log-connections
or
parameters_extAX25 VC-reject-login VC-send-failure-msg VC-log-connections
FILES
/etc/ax25/ax25d.conf
SEE ALSO
ax25(4), netrom(4), rose(4), axports(5), nrports(5), rsports(5), ax25d(8).