Provided by: shorewall6_4.5.21.6-1_all 
NAME
rules - Shorewall6 rules file
SYNOPSIS
/etc/shorewall6/rules
DESCRIPTION
Entries in this file govern connection establishment by defining exceptions to the policies laid out in
shorewall6-policy[1](5). By default, subsequent requests and responses are automatically allowed using
connection tracking. For any particular (source,dest) pair of zones, the rules are evaluated in the order
in which they appear in this file and the first terminating match is the one that determines the
disposition of the request. All rules are terminating except LOG and QUEUE rules.
The rules file is divided into sections. Each section is introduced by a "Section Header" which is a line
beginning with SECTION and followed by the section name.
Sections are as follows and must appear in the order listed:
ALL
This section was added in Shorewall 4.4.23. rules in this section are applied, regardless of the
connection tracking state of the packet.
ESTABLISHED
Packets in the ESTABLISHED state are processed by rules in this section.
The only ACTIONs allowed in this section are ACCEPT, DROP, REJECT, LOG and QUEUE
There is an implicit ACCEPT rule inserted at the end of this section.
RELATED
Packets in the RELATED state are processed by rules in this section.
The only ACTIONs allowed in this section are ACCEPT, DROP, REJECT, LOG and QUEUE
There is an implicit rule added at the end of this section that invokes the RELATED_DISPOSITION
(shorewall6.conf[2](5)).
INVALID
Added in Shorewall 4.5.13. Packets in the INVALID state are processed by rules in this section.
The only Actions allowed in this section are ACCEPT, DROP, REJECT, LOG and QUEUE.
There is an implicit rule added at the end of this section that invokes the INVALID_DISPOSITION
(shorewall6.conf[2](5)).
UNTRACKED
Added in Shorewall 4.5.13. Packets in the UNTRACKED state are processed by rules in this section.
The only Actions allowed in this section are ACCEPT, DROP, REJECT, LOG and QUEUE.
There is an implicit rule added at the end of this section that invokes the UNTRACKED_DISPOSITION
(shorewall6.conf[2](5)).
NEW
Packets in the NEW, INVALID and UNTRACKED states are processed by rules in this section.
Note
If you are not familiar with Netfilter to the point where you are comfortable with the differences
between the various connection tracking states, then it is suggested that you omit the ESTABLISHED
and RELATED sections and place all of your rules in the NEW section (That's after the line that reads
SECTION NEW').
Warning
If you specify FASTACCEPT=Yes in shorewall6.conf[2](5) then the ESTABLISHED and RELATED sections must
be empty.
An except is made if you are running Shorewall 4.4.27 or later and you have specified a non-default
value for RELATED_DISPOSITION or RELATED_LOG_LEVEL. In that case, you may have rules in the RELATED
section of this file.
You may omit any section that you don't need. If no Section Headers appear in the file then all rules are
assumed to be in the NEW section.
The columns in the file are as follows (where the column name is followed by a different name in
parentheses, the different name is used in the alternate specification syntax).
ACTION - target[:{log-level|none}[!][:tag]]
Specifies the action to be taken if the connection request matches the rule. target must be one of
the following.
ACCEPT
Allow the connection request.
ACCEPT+
like ACCEPT but also excludes the connection from any subsequent matching DNAT[-] or REDIRECT[-]
rules. Requires Shorewall 4.5.14 or later.
ACCEPT!
like ACCEPT but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
action
The name of an action declared in shorewall6-actions[3](5) or in
/usr/share/shorewall/actions.std.
ADD(ipset:flags)
Added in Shorewall 4.4.12. Causes addresses and/or port numbers to be added to the named ipset.
The flags specify the address or tuple to be added to the set and must match the type of ipset
involved. For example, for an iphash ipset, either the SOURCE or DESTINATION address can be added
using flags src or dst respectively (see the -A command in ipset (8)).
ADD is non-terminating. Even if a packet matches the rule, it is passed on to the next rule.
AUDIT[(accept|drop|reject)]
Added in Shorewall 4.5.10. Audits the packet with the specified type; if the type is omitted,
then drop is assumed. Require AUDIT_TARGET support in the kernel and iptables.
A_ACCEPT, and A_ACCEPT!
Added in Shorewall 4.4.20. Audited versions of ACCEPT and ACCEPT! respectively. Require
AUDIT_TARGET support in the kernel and iptables.
A_DROP and A_DROP!
Added in Shorewall 4.4.20. Audited versions of DROP and DROP! respectively. Require AUDIT_TARGET
support in the kernel and iptables.
A_REJECT AND A_REJECT!
Added in Shorewall 4.4.20. Audited versions of REJECT and REJECT! respectively. Require
AUDIT_TARGET support in the kernel and iptables.
[?]COMMENT
the rest of the line will be attached as a comment to the Netfilter rule(s) generated by the
following entries. The comment will appear delimited by "/* ... */" in the output of "shorewall
show <chain>". To stop the comment from being attached to further rules, simply include COMMENT
on a line by itself.
Note
Beginning with Shorewall 4.5.11, ?COMMENT is a synonym for COMMENT and is preferred.
CONTINUE
For experts only.
Do not process any of the following rules for this (source zone,destination zone). If the source
and/or destination IP address falls into a zone defined later in shorewall6-zones[4](5) or in a
parent zone of the source or destination zones, then this connection request will be passed to
the rules defined for that (those) zone(s). See shorewall6-nesting[5](5) for additional
information.
CONTINUE!
like CONTINUE but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
COUNT
Simply increment the rule's packet and byte count and pass the packet to the next rule.
DEL(ipset:flags)
Added in Shorewall 4.4.12. Causes an entry to be deleted from the named ipset. The flags specify
the address or tuple to be deleted from the set and must match the type of ipset involved. For
example, for an iphash ipset, either the SOURCE or DESTINATION address can be deleted using flags
src or dst respectively (see the -D command in ipset (8)).
DEL is non-terminating. Even if a packet matches the rule, it is passed on to the next rule.
DNAT
Forward the request to another system (and optionally another port). Requires Shorewall 4.5.14 or
later.
DNAT-
Advanced users only.
Like DNAT but only generates the DNAT iptables rule and not the companion ACCEPT rule. Requires
Shorewall 4.5.14 or later.
DROP
Ignore the request.
DROP!
like DROP but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
HELPER
Added in Shorewall 4.5.7. This action requires that the HELPER column contains the name of the
Netfilter helper to be associated with connections matching this connection. May only be
specified in the NEW section and is useful for being able to specify a helper when the applicable
policy is ACCEPT. No destination zone should be specified in HELPER rules.
INLINE[(action)]
Added in Shorewall 4.5.16. This action allows you to construct most of the rule yourself using
ip6tables syntax. The part that you specify must follow a semicolon (';') and is completely
free-form. If the target of the rule (the part following 'j') is something that Shorewall
supports in the ACTION column, then you may enclose it in parentheses (e.g., INLINE(ACCEPT)).
Otherwise, you can include it after the semicolon. In this case, you must declare the target as a
builtin action in shorewall6-actions[3](5).
Some considerations when using INLINE:
• The p, s, d, i, o, policy, and state match (state or conntrack --ctstate) matches will always
appear in the front of the rule in that order.
• When multiple matches are specified, the compiler will keep them in the order in which they
appear (excluding the above listed ones), but they will not necessarily be at the end of the
generated rule. For example, if addresses are specified in the SOURCE and/or DEST columns,
their generated matches will appear after those specified using ';'.
LOG:level
Simply log the packet and continue with the next rule.
macro[(macrotarget)]
The name of a macro defined in a file named macro.macro. If the macro accepts an action parameter
(Look at the macro source to see if it has PARAM in the TARGET column) then the macro name is
followed by the parenthesized macrotarget (ACCEPT, DROP, REJECT, ...) to be substituted for the
parameter.
Example: FTP(ACCEPT).
The older syntax where the macro name and the target are separated by a slash (e.g. FTP/ACCEPT)
is still allowed but is deprecated.
NFLOG[(nflog-parameters)]
Added in Shorewall 4.5.9.3. Queues matching packets to a back end logging daemon via a netlink
socket then continues to the next rule. See http://www.shorewall.net/shorewall_logging.html[6].
Similar to LOG:NFLOG[(nflog-parameters)], except that the log level is not changed when this
ACTION is used in an action or macro and the invocation of that action or macro specifies a log
level.
NFQUEUE[(queuenumber)]
Queues the packet to a user-space application using the nfnetlink_queue mechanism. If a
queuenumber is not specified, queue zero (0) is assumed.
NFQUEUE![(queuenumber)]
like NFQUEUE but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
NONAT
Excludes the connection from any subsequent DNAT[-] or REDIRECT[-] rules but doesn't generate a
rule to accept the traffic. Requires Shorewall 4.5.14 or later.
QUEUE
Queue the packet to a user-space application such as ftwall (http://p2pwall.sf.net). The
application may reinsert the packet for further processing.
QUEUE!
like QUEUE but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
REDIRECT
Redirect the request to a server running on the firewall. Requires Shorewall 4.5.14 or later.
REDIRECT-
Advanced users only.
Like REDIRECT but only generates the REDIRECT iptables rule and not the companion ACCEPT rule.
Requires Shorewall 4.5.14 or later.
REJECT
disallow the request and return an icmp-unreachable or an RST packet.
REJECT!
like REJECT but exempts the rule from being suppressed by OPTIMIZE=1 in shorewall6.conf[2](5).
The target may optionally be followed by ":" and a syslog log level (e.g, REJECT:info or
Web(ACCEPT):debug). This causes the packet to be logged at the specified level. Note that if the
ACTION involves destination network address translation (DNAT, REDIRECT, etc.) then the packet is
logged before the destination address is rewritten.
If the ACTION names an action declared in shorewall-actions[7](5) or in
/usr/share/shorewall/actions.std then:
• If the log level is followed by "!' then all rules in the action are logged at the log level.
• If the log level is not followed by "!" then only those rules in the action that do not specify
logging are logged at the specified level.
• The special log level none! suppresses logging by the action.
You may also specify ULOG or NFLOG (must be in upper case) as a log level.This will log to the ULOG
or NFLOG target for routing to a separate log through use of ulogd
(http://www.netfilter.org/projects/ulogd/index.html).
Actions specifying logging may be followed by a log tag (a string of alphanumeric characters) which
is appended to the string generated by the LOGPREFIX (in shorewall.conf[8](5)).
Example: ACCEPT:info:ftp would include 'ftp ' at the end of the log prefix generated by the LOGPREFIX
setting.
SOURCE -
{zone|zone-list[+]|{all|any}[+][-]}[:interface][:<{address-or-range[,address-or-range]...[exclusion]>|exclusion|+ipset|^countrycode-list}
Source hosts to which the rule applies. May be a zone declared in /etc/shorewall6/zones, $FW to
indicate the firewall itself, all, all+, all-, all+- or none.
Beginning with Shorewall 4.4.13, you may use a zone-list which consists of a comma-separated list of
zones declared in shorewall-zones[9] (5). This zone-list may be optionally followed by "+" to
indicate that the rule is to apply to intra-zone traffic as well as inter-zone traffic.
When none is used either in the SOURCE or DEST column, the rule is ignored.
all means "All Zones", including the firewall itself. all- means "All Zones, except the firewall
itself". When all[-] is used either in the SOURCE or DEST column intra-zone traffic is not affected.
When all+[-] is "used, intra-zone traffic is affected. Beginning with Shorewall 4.4.13, exclusion is
supported -- see see shorewall6-exclusion[10](5).
Except when all[+][-] or any[+][-] is specified, clients may be further restricted to a list of
networks and/or hosts by appending ":" and a comma-separated list of network and/or host addresses.
Hosts may be specified by IP or MAC address; mac addresses must begin with "~" and must use "-" as a
separator.
any is equivalent to all when there are no nested zones. When there are nested zones, any only refers
to top-level zones (those with no parent zones). Note that any excludes all vserver zones, since
those zones are nested within the firewall zone.
Hosts may also be specified as an IP address range using the syntax lowaddress-highaddress. This
requires that your kernel and ip6tables contain iprange match support. If your kernel and ip6tables
have ipset match support then you may give the name of an ipset prefaced by "+". The ipset name may
be optionally followed by a number from 1 to 6 enclosed in square brackets ([]) to indicate the
number of levels of source bindings to be matched.
Beginning with Shorewall6 4.4.17, the primary IP address of a firewall interface can be specified by
an ampersand ('&') followed by the logical name of the interface as found in the INTERFACE column of
shorewall6-interfaces[11] (5).
Beginning with Shorewall 4.5.4, A countrycode-list may be specified. A countrycode-list is a
comma-separated list of up to 15 two-character ISO-3661 country codes enclosed in square brackets
('[...]') and preceded by a caret ('^'). When a single country code is given, the square brackets may
be omitted. A list of country codes supported by Shorewall may be found at
http://www.shorewall.net/ISO-3661.html. Specifying a countrycode-list requires GeoIP Match support in
your ip6tables and Kernel.
When an interface is not specified, you may omit the angled brackets ('<' and '>') around the
address(es) or you may supply them to improve readability.
You may exclude certain hosts from the set already defined through use of an exclusion (see
shorewall6-exclusion[10](5)).
Examples:
dmz:2002:ce7c::92b4:1::2
Host 2002:ce7c:92b4:1::2 in the DMZ
net:2001:4d48:ad51:24::/64
Subnet 2001:4d48:ad51:24::/64 on the Internet
loc:<2002:cec792b4:1::2,2002:cec792b4:1::44>
Hosts 2002:cec792b4:1::2 and 2002:cec792b4:1::44 in the local zone.
loc:~00-A0-C9-15-39-78
Host in the local zone with MAC address 00:A0:C9:15:39:78.
net:2001:4d48:ad51:24::/64!2001:4d48:ad51:24:6:/80!2001:4d48:ad51:24:6:/80
Subnet 2001:4d48:ad51:24::/64 on the Internet except for 2001:4d48:ad51:24:6:/80.
$FW:ð0
The primary IP address of eth0 in the firewall zone (Shorewall6 4.4.17 and later).
Alternatively, clients may be specified by interface by appending ":" to the zone name followed by
the interface name. For example, loc:eth1 specifies a client that communicates with the firewall
system through eth1. This may be optionally followed by another colon (":") and an IP/MAC/subnet
address as described above (e.g., loc:eth1:<2002:ce7c::92b4:1::2>).
Examples:
loc:eth1:<2002:cec792b4:1::2,2002:cec792b4:1::44>
Hosts 2002:cec792b4:1::2 and 2002:cec792b4:1::44 in the Local zone, with both originating from
eth1
DEST -
{zone|zone-list[+]|all[+][-]}[:interface][:<{address-or-range[,address-or-range]...[exclusion]>|exclusion|+ipset|^countrycode-list}[:port[:random]]
Location of Server. May be a zone declared in shorewall6-zones[4](5), $FW to indicate the firewall
itself, all. all+ or none.
Beginning with Shorewall 4.4.13, you may use a zone-list which consists of a comma-separated list of
zones declared in shorewall-zones[9] (5). Ths zone-list may be optionally followed by "+" to indicate
that the rule is to apply to intra-zone traffic as well as inter-zone traffic. Beginning with
Shorewall-4.4.13, exclusion is supported -- see see shorewall6-exclusion[10](5).
Beginning with Shorewall6 4.4.17, the primary IP address of a firewall interface can be specified by
an ampersand ('&') followed by the logical name of the interface as found in the INTERFACE column of
shorewall6-interfaces[11] (5).
Beginning with Shorewall 4.5.4, A countrycode-list may be specified. A countrycode-list is a
comma-separated list of up to 15 two-character ISO-3661 country codes enclosed in square brackets
('[...]') and preceded by a caret ('^'). When a single country code is given, the square brackets may
be omitted. A list of country codes supported by Shorewall may be found at
http://www.shorewall.net/ISO-3661.html. Specifying a countrycode-list requires GeoIP Match support in
your ip6tables and Kernel.
When none is used either in the SOURCE or DEST column, the rule is ignored.
When all is used either in the SOURCE or DEST column intra-zone traffic is not affected. When all+ is
used, intra-zone traffic is affected.
If the DEST zone is a bport zone, then either:
1. the SOURCE must be all[+][-], or
2. the SOURCE zone must be another bport zone associated with the same bridge, or
3. the SOURCE zone must be an ipv4 zone that is associated with only the same bridge.
Except when all[+]|[-] is specified, the server may be further restricted to a particular network,
host or interface by appending ":" and the network, host or interface. See SOURCE above.
You may exclude certain hosts from the set already defined through use of an exclusion (see
shorewall6-exclusion[10](5)).
Restriction: MAC addresses are not allowed (this is a Netfilter restriction).
If you kernel and ip6tables have ipset match support then you may give the name of an ipset prefaced
by "+". The ipset name may be optionally followed by a number from 1 to 6 enclosed in square brackets
([]) to indicate the number of levels of destination bindings to be matched. Only one of the SOURCE
and DEST columns may specify an ipset name.
The port that the server is listening on may be included and separated from the server's IP address
by ":". If omitted, the firewall will not modify the destination port. A destination port may only be
included if the ACTION is DNAT or REDIRECT.
Example 1:
loc:[2001:470:b:227::44]:3128 specifies a local server at IP address 2001:470:b:227::44 and
listening on port 3128.
Example 2:
loc:[]:3128 specifies that the destination port should be changed to 3128 but the IP address
should remain the same.
The port may be specified as a service name. You may specify a port range in the form
lowport-highport to cause connections to be assigned to ports in the range in round-robin fashion.
When a port range is specified, lowport and highport must be given as integers; service names are not
permitted. Additionally, the port range may be optionally followed by :random which causes assignment
to ports in the list to be random.
If the ACTION is REDIRECT or REDIRECT-, this column needs only to contain the port number on the
firewall that the request should be redirected to. That is equivalent to specifying $FW::port.
PROTO - {-|tcp:syn|ipp2p|ipp2p:udp|ipp2p:all|protocol-number|protocol-name|all}
Optional protocol - ipp2p* requires ipp2p match support in your kernel and ip6tables. tcp:syn
implies tcp plus the SYN flag must be set and the RST,ACK and FIN flags must be reset.
Beginning with Shorewall6 4.4.19, this column can contain a comma-separated list of protocol-numbers
and/or protocol names (e.g., tcp,udp).
DEST PORT(S) (dport) - {-|port-name-number-or-range[,port-name-number-or-range]...}
Optional destination Ports. A comma-separated list of Port names (from services(5)), port numbers or
port ranges; if the protocol is icmp, this column is interpreted as the destination icmp-type(s).
ICMP types may be specified as a numeric type, a numeric type and code separated by a slash (e.g.,
3/4), or a typename. See http://www.shorewall.net/configuration_file_basics.htm#ICMP. Note that prior
to Shorewall6 4.4.19, only a single ICMP type may be listed.
If the protocol is ipp2p, this column is interpreted as an ipp2p option without the leading "--"
(example bit for bit-torrent). If no port is given, ipp2p is assumed.
A port range is expressed as lowport:highport.
This column is ignored if PROTO = all but must be entered if any of the following columns are
supplied. In that case, it is suggested that this field contain a dash (-).
If your kernel contains multi-port match support, then only a single Netfilter rule will be generated
if in this list and the CLIENT PORT(S) list below:
1. There are 15 or less ports listed.
2. No port ranges are included or your kernel and ip6tables contain extended multi-port match
support.
SOURCE PORT(S) (sport) - {-|port-name-number-or-range[,port-name-number-or-range]...}
Optional source port(s). If omitted, any source port is acceptable. Specified as a comma- separated
list of port names, port numbers or port ranges.
Beginning with Shorewall 4.5.15, you may place '=' in this column, provided that the DEST PORT(S)
column is non-empty. This causes the rule to match when either the source port or the destination
port in a packet matches one of the ports specified in DEST PORTS(S). Use of '=' requires multi-port
match in your iptables and kernel.
Warning
Unless you really understand IP, you should leave this column empty or place a dash (-) in the
column. Most people who try to use this column get it wrong.
If you don't want to restrict client ports but need to specify a later column, then place "-" in this
column.
If your kernel contains multi-port match support, then only a single Netfilter rule will be generated
if in this list and the DEST PORT(S) list above:
1. There are 15 or less ports listed.
2. No port ranges are included or your kernel and ip6tables contain extended multi-port match
support.
ORIGINAL DEST (origdest) - [-]
Included for compatibility with Shorewall. Enter '-' in this column if you need to specify one of the
later columns.
RATE LIMIT (rate) - [-|[{s|d}:[[name]:]]]rate/{sec|min|hour|day}[:burst]
You may optionally rate-limit the rule by placing a value in this column:
rate is the number of connections per interval (sec or min) and burst is the largest burst permitted.
If no burst is given, a value of 5 is assumed. There may be no no white-space embedded in the
specification.
Example: 10/sec:20
When s: or d: is specified, the rate applies per source IP address or per destination IP address
respectively. The name may be chosen by the user and specifies a hash table to be used to count
matching connections. If not given, the name shorewallN (where N is a unique integer) is assumed.
Where more than one POLICY specifies the same name, the connections counts for the rules are
aggregated and the individual rates apply to the aggregated count.
USER/GROUP (user) - [!][user-name-or-number-or-range][:group-name-or-number-or-range]
This optional column may only be non-empty if the SOURCE is the firewall itself.
When this column is non-empty, the rule applies only if the program generating the output is running
under the effective user and/or group specified (or is NOT running under that id if "!" is given).
Beginning with Shorewall 4.5.8, multiple user or group names/ids separated by commas may be
specified.
Examples:
joe
program must be run by joe
:kids
program must be run by a member of the 'kids' group
!:kids
program must not be run by a member of the 'kids' group
2001-2099
UIDs 2001 through 2099 (Shorewall 4.5.6 and later)
MARK - [!]value[/mask][:C]
Defines a test on the existing packet or connection mark. The rule will match only if the test
returns true.
If you don't want to define a test but need to specify anything in the following columns, place a "-"
in this field.
!
Inverts the test (not equal)
value
Value of the packet or connection mark.
mask
A mask to be applied to the mark before testing.
:C
Designates a connection mark. If omitted, the packet mark's value is tested.
CONNLIMIT - [!]limit[:mask]
May be used to limit the number of simultaneous connections from each individual host to limit
connections. Requires connlimit match in your kernel and ip6tables. While the limit is only checked
on rules specifying CONNLIMIT, the number of current connections is calculated over all current
connections from the SOURCE host. By default, the limit is applied to each host but can be made to
apply to networks of hosts by specifying a mask. The mask specifies the width of a VLSM mask to be
applied to the source address; the number of current connections is then taken over all hosts in the
subnet source-address/mask. When ! is specified, the rule matches when the number of connection
exceeds the limit.
TIME - timeelement[&timeelement...]
May be used to limit the rule to a particular time period each day, to particular days of the week or
month, or to a range defined by dates and times. Requires time match support in your kernel and
ip6tables.
timeelement may be:
timestart=hh:mm[:ss]
Defines the starting time of day.
timestop=hh:mm[:ss]
Defines the ending time of day.
utc
Times are expressed in Greenwich Mean Time.
localtz
Deprecated by the Netfilter team in favor of kerneltz. Times are expressed in Local Civil Time
(default).
kerneltz
Added in Shorewall 4.5.2. Times are expressed in Local Kernel Time (requires iptables 1.4.12 or
later).
weekdays=ddd[,ddd]...
where ddd is one of Mon, Tue, Wed, Thu, Fri, Sat or Sun
monthdays=dd[,dd],...
where dd is an ordinal day of the month
datestart=yyyy[-mm[-dd[Thh[:mm[:ss]]]]]
Defines the starting date and time.
datestop=yyyy[-mm[-dd[Thh[:mm[:ss]]]]]
Defines the ending date and time.
HEADERS - [!][any:|exactly:]header-list (Optional - Added in Shorewall 4.4.15)
The header-list consists of a comma-separated list of headers from the following list.
auth, ah, or 51
Authentication Headers extension header.
esp, or 50
Encrypted Security Payload extension header.
hop, hop-by-hop or 0
Hop-by-hop options extension header.
route, ipv6-route or 41
IPv6 Route extension header.
frag, ipv6-frag or 44
IPv6 fragmentation extension header.
none, ipv6-nonxt or 59
No next header
proto, protocol or 255
Any protocol header.
If any: is specified, the rule will match if any of the listed headers are present. If exactly: is
specified, the will match packets that exactly include all specified headers. If neither is given,
any: is assumed.
If ! is entered, the rule will match those packets which would not be matched when ! is omitted.
SWITCH - [!]switch-name[={0|1}]
Added in Shorewall6 4.4.24 and allows enabling and disabling the rule without requiring shorewall6
restart.
Enables the rule if the value stored in /proc/net/nf_condition/switch-name is 1. Disables the rule if
that file contains 0 (the default). If '!' is supplied, the test is inverted such that the rule is
enabled if the file contains 0.
Within the switch-name, '@0' and '@{0}' are replaced by the name of the chain to which the rule is a
added. The switch-name (after '@...' expansion) must begin with a letter and be composed of letters,
decimal digits, underscores or hyphens. Switch names must be 30 characters or less in length.
Switches are normally off. To turn a switch on:
echo 1 >
/proc/net/nf_condition/switch-name
To turn it off again:
echo 0 >
/proc/net/nf_condition/switch-name
Switch settings are retained over shorewall6 restart.
Beginning with Shorewall 4.5.10, when the switch-name is followed by =0 or =1, then the switch is
initialized to off or on respectively by the start command. Other commands do not affect the switch
setting.
HELPER - [helper]
Added in Shorewall 4.5.7.
In the NEW section, causes the named conntrack helper to be associated with this connection; the
contents of this column are ignored unless ACTION is ACCEPT*, DNAT* or REDIRECT*.
In the RELATED section, will only match if the related connection has the named helper associated
with it.
The helper may be one of:
amanda
ftp
irc
netbios-ns
pptp
Q.931
RAS
sane
sip
snmp
tftp
If the HELPERS option is specified in shorewall.conf[8](5), then any module specified in this column
must be listed in the HELPERS setting.
EXAMPLE
Example 1:
Accept SMTP requests from the DMZ to the internet
#ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# PORT PORT(S) DEST
ACCEPT dmz net tcp smtp
Example 4:
You want to accept SSH connections to your firewall only from internet IP addresses
2002:ce7c::92b4:1::2 and 2002:ce7c::92b4:1::22
#ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL
# PORT PORT(S) DEST
ACCEPT net:<2002:ce7c::92b4:1::2,2002:ce7c::92b4:1::22> \
$FW tcp 22
Example 5:
You wish to limit SSH connections from remote systems to 1/min with a burst of three (to allow for
limited retry):
#ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL RATE
# PORT(S) PORT(S) DEST LIMIT
SSH(ACCEPT) net all - - - - s:1/min:3
Example 6:
Forward port 80 to dmz host $BACKUP if switch 'primary_down' is set.
#ACTION SOURCE DEST PROTO DEST SOURCE ORIGINAL RATE USER/ MARK CONNLIMIT TIME HEADERS SWITCH
# PORT(S) PORT(S) DEST LIMIT GROUP
DNAT net dmz:$BACKUP tcp 80 - - - - - - - - primary_down
Example 7:
Drop all email from IP addresses in the country whose ISO-3661 country code is ZZ.
#ACTION SOURCE DEST PROTO DEST
# PORT(S)
DROP net:^ZZ fw tcp 25
Example 8:
You want to generate your own rule involving ip6tables targets and matches not supported by
Shorewall.
#ACTION SOURCE DEST PROTO DEST
# PORT(S)
INLINE $FW net ; -p 6 -m mickey-mouse --name test -m set --match-set set1 src -m mickey-mouse --name test2 -j SECCTX --name test3
The above will generate the following ip6tables-restore input:
-A fw2net -p 6 -m mickey-mouse --name test -m set --match-set set1 src -m mickey-mouse --name test2 -j SECCTX --name test3
Note that SECCTX must be defined as a builtin action in shorewall6-actions[3](5):
#ACTION OPTIONS
SECCTX builtin
FILES
/etc/shorewall6/rules
SEE ALSO
http://www.shorewall.net/shorewall_logging.html
http://shorewall.net/configuration_file_basics.htm#Pairs
shorewall6(8), shorewall6-accounting(5), shorewall6-actions(5), shorewall6-blacklist(5),
shorewall6-blrules(5), shorewall6-hosts(5), shorewall6-interfaces(5), shorewall6-maclist(5),
shorewall6-netmap(5),shorewall6-params(5), shorewall6-policy(5), shorewall6-providers(5),
shorewall6-rtrules(5), shorewall6-routestopped(5), shorewall6.conf(5), shorewall6-secmarks(5),
shorewall6-tcclasses(5), shorewall6-tcdevices(5), shorewall6-tcrules(5), shorewall6-tos(5),
shorewall6-tunnels(5), shorewall6-zones(5)
NOTES
1. shorewall6-policy
http://www.shorewall.netshorewall6-policy.html
2. shorewall6.conf
http://www.shorewall.netshorewall6.conf.html
3. shorewall6-actions
http://www.shorewall.netshorewall6-actions.html
4. shorewall6-zones
http://www.shorewall.netshorewall6-zones.html
5. shorewall6-nesting
http://www.shorewall.netshorewall6-nesting.html
6. http://www.shorewall.net/shorewall_logging.html
http://www.shorewall.net/shorewall.logging.html
7. shorewall-actions
http://www.shorewall.netshorewall-actions.html
8. shorewall.conf
http://www.shorewall.netshorewall.conf.html
9. shorewall-zones
http://www.shorewall.netshorewall-zones.html
10. shorewall6-exclusion
http://www.shorewall.netshorewall6-exclusion.html
11. shorewall6-interfaces
http://www.shorewall.netshorewall-interfaces.html
[FIXME: source] 01/30/2014 SHOREWALL6-RULES(5)