Ubuntu Manpage: oping - send ICMP ECHO

NAME

       oping - send ICMP ECHO_REQUEST to network hosts

SYNOPSIS

       oping [-4 | -6] [-c count] [-i interval] host [host [host ...]]

       oping [-4 | -6] [-c count] [-i interval] -f filename

       noping [-4 | -6] [-c count] [-i interval] host [host [host ...]]

       noping [-4 | -6] [-c count] [-i interval] -f filename

DESCRIPTION

       oping uses ICMPv4 or ICMPv6 ECHO_REQUEST packets to measure a hosts reachability and the network latency.
       In contrast to the original ping(8) utility oping can send ICMP packets to multiple hosts in parallel and
       wait for all ECHO_RESPONSE packets to arrive. In contrast to the fping utility (URL is listed in "SEE
       ALSO") oping can use both, IPv4 and IPv6 transparently and side by side.

       noping is an ncurses-based front-end to liboping which displays ping statistics online and highlights
       aberrant round-trip times if the terminal supports colors.

OPTIONS

-4 Force the use of IPv4.

-6 Force the use of IPv6.

-c count
Send (and receive) count ICMP packets, then stop and exit.

-i interval
Send one ICMP packet (per host) each interval seconds. This can be a floating-point number to specify
sub-second precision.

-t ttl
Set the IP Time to Live to ttl. This must be a number between (and including) 1 and 255. If omitted,
the value 64 is used.

-I address
Set the source address to use. You may either specify an IP number or a hostname. You cannot pass the
interface name, as you can with GNU's ping(8) - use the -D option for that purpose.

-D interface name
Set the outgoing network device to use.

-f filename
Instead of specifying hostnames on the command line, read them from filename. If filename is -, read
from "STDIN".

If oping is installed with the SetUID-bit, it will set the effective UID to the real UID before
opening the file. In the special (but common) case that oping is owned by the super-user (UID 0),
this means that privileges are temporarily dropped before opening the file, in order to prevent users
from reading arbitrary files on the system.

If your system doesn't provide saved set-user IDs (this was an optional feature before POSIX 2001),
the behavior is different because it is not possible to temporarily drop privileges. The alternative
behavior is: If the real user ID (as returned by getuid(2)) and the effective user ID (as returned by
geteuid(2)) differ, the only argument allowed for this option is "-" (i.e. standard input).

-Q qos
Specify the Quality of Service (QoS) for outgoing packets. This is a somewhat tricky option, since
the meaning of the bits in the IPv4 header has been revised several times.

The currently recommended method is Differentiated Services which is used in IPv6 headers as well.
There are shortcuts for various predefined per-hop behaviors (PHBs):

be Selects the Best Effort behavior. This is the default behavior.

ef Selects the Expedited Forwarding (EF) per-hop behavior, as defined in RFC 3246. This PHB is
characterised by low delay, low loss and low jitter, i.e. high priority traffic.

va Selects the Voice Admitted (VA) per-hop behavior, as defined in RFC 5865. This traffic class is
meant for Voice over IP (VoIP) traffic which uses Call Admission Control (CAC) for reserving
network capacity.

afcp
Selects one of 12 differentiated services code points (DSCPs), which are organized in four
classes with three priorities each. Therefore, c must be a number between 1 through 4 and p must
be a number between 1 through 3, for example "af13", "af22" and "af41". In each class, the lower
priority number takes precedence over the higher priority number.

csn Selects one of the eight Class Selector PHBs. n is a number between 0 through 7. The class
selectors have been defined to be compatible to the Precedence field in the IPv4 header as
defined in RFC 791. Please note that "cs0" is synonymous to "be".

The old definition of the same bits in the IPv4 header was as Type of Service (ToS) field, specified
in RFC 1349. It defined four possible values which have appropriate aliases. Please note that this
use of the bits is deprecated and the meaning is limited to IPv4!

lowdelay
Minimize delay

throughput
Maximize throughput

reliability
Maximize reliability

mincost
Minimize monetary cost

Alternatively, you can also specify the byte manually. You can use either a decimal number (0-255), a
hexadecimal number (0x00-0xff) or an octal number (00-0377) using the usual "0x" and "0" prefixes for
hexadecimal and octal respectively.

The printed lines will contain information about the QoS field of received packets if either a non-
standard QoS setting was used on outgoing packets or if the QoS byte of incoming packets is not zero.
In other words, the QoS information is omitted if both, the outgoing and the incoming QoS bytes are
zero. The received byte is always interpreted as Differentiated Services Code Point (DSCP) and
Explicit Congestion Notification (ECN), even if the deprecated Type of Service (ToS) aliases were
used to specify the bits of outgoing packets.

-Z percent
If any hosts have a drop rate higher than percent, where percent is a number between zero and 100
inclusively, exit with a non-zero exit status. Since it is not possible to have a higher drop rate
than 100%, passing this limit will effectively disable the feature (the default). Setting the option
to zero means that the exit status will only be zero if all replies for all hosts have been received.

The exit status will indicate the number of hosts with more than percent packets lost, up to a number
of 255 failing hosts.

-u|-U
noping only -u forces UTF-8 output, -U disables UTF-8 output. If neither is given, the codeset is
automatically determined from the locale.

COLORS

       If  supported  by  the terminal, noping will highlight the round-trip times (RTT) using the colors green,
       yellow and red. Green signals RTTs that are in the "expected"  range,  yellow  marks  moderately  unusual
       times and times that differ a lot from the expected value are printed in red.

       The  information  used  to  categorize  round-trip  times is the average round-trip time and the standard
       deviation. RTTs that differ from the average by less than the standard deviation  are  considered  to  be
       "normal"  and  are  printed in green. Times that differ from the average more than the standard deviation
       but less than twice the standard deviation are considered "moderately unusual" and are printed in yellow.
       Times differing more than twice the standard deviation from the average are considered  to  be  "unusual"
       and are printed in red.

AUTHOR