Provided by: sg3-utils_1.36-1ubuntu1_amd64 
NAME
sg3_utils - a package of utilities for sending SCSI commands
SYNOPSIS
sg_* [--help] [--hex] [--maxlen=LEN] [--raw] [--verbose] [--version] [OTHER_OPTIONS] DEVICE
DESCRIPTION
sg3_utils is a package of utilities that send SCSI commands to the given DEVICE via a SCSI pass through
interface provided by the host operating system.
The names of all utilities start with "sg" and most start with "sg_" often followed by the name, or a
shortening of the name, of the SCSI command that they send. For example the "sg_verify" utility sends the
SCSI VERIFY command. A mapping between SCSI commands and the sg3_utils utilities that issue them is shown
in the COVERAGE file.
SCSI draft standards can be found at http://www.t10.org . The standards themselves can be purchased from
ANSI and other standards organizations. A good overview of various SCSI standards can be seen in
http://www.t10.org/scsi-3.htm with the SCSI command sets in the upper part of the diagram. SCSI commands
in common with all device types can be found in SPC of which SPC-4 is the latest major version. Block
device specific commands (e.g. as used by disks) are in SBC, those for tape drives in SSC and those for
CD/DVD/BD drives in MMC.
It is becoming more common to control ATA disks with the SCSI command set. This involves the translation
of SCSI commands to their corresponding ATA equivalents (and that is an imperfect mapping in some cases).
The relevant standard is called SCSI to ATA Translation (SAT and SAT-2 are now standards at INCITS(ANSI)
and ISO while SAT-3 is at the draft stage). The logic to perform the command translation is often called
a SAT Layer or SATL and may be within an operating system, in host bus adapter firmware or in an external
device (e.g. associated with a SAS expander). See http://www.t10.org for more information.
There is some support for SCSI tape devices but not for their basic commands. The reader is referred to
the "mt" utility.
There are two generations of command line option usage. The newer utilities (written since July 2004) use
the getopt_long() function to parse command line options. With that function, each option has two
representations: a short form (e.g. '-v') and a longer form (e.g. '--verbose'). If an argument is
required then it follows a space (optionally) in the short form and a "=" in the longer form (e.g. in the
sg_verify utility '-l 2a6h' and '--lba=2a6h' are equivalent). Note that with getopt_long(), short form
options can be elided, for example: '-all' is equivalent to '-a -l -l'. The DEVICE argument may appear
after, between or prior to any options.
The older utilities, such as sg_inq, had individual command line processing code typically based on a
single "-" followed by one or more characters. If an argument is needed then it follows a "=" (e.g.
'-p=1f' in sg_modes with its older interface). Various options can be elided as long as it is not
ambiguous (e.g. '-vv' to increase the verbosity).
Over time the command line interface of these older utilities became messy and overloaded with options.
So in sg3_utils version 1.23 the command line interface of these older utilities was altered to have both
a cleaner getopt_long() interface and their older interface for backward compatibility. By default these
older utilities use their getopt_long() based interface. That can be overridden by defining the
SG3_UTILS_OLD_OPTS environment variable or using '-O' or '--old' as the first command line option. The
man pages of the older utilities documents the details.
Several sg3_utils utilities are based on the Unix dd command (e.g. sg_dd) and permit copying data at the
level of SCSI READ and WRITE commands. sg_dd is tightly bound to Linux and hence is not ported to other
OSes. A more generic utility (than sg_dd) called ddpt in a package of the same name has been ported to
other OSes.
LINUX DEVICE NAMING
Normal disk block devices have names like /dev/sda, /dev/sdb, /dev/sdc, etc. SCSI disks in Linux have
always had names like that but in recent Linux kernels (e.g. lk 2.6 series) it is becoming more common
for almost all disks to be named like that. Partitions within a disk are specified by a number appended
to the device name, starting at 1 (e.g. /dev/sda1 ).
Tape drives are named /dev/st<num> or /dev/nst<num> where <num> starts at zero. Additionally one letter
from this list: "lma" may be appended to the name. CD, DVD and BD readers (and writers) are named
/dev/sr<num> where <num> start at zero. There are less used SCSI device type names, the dmesg and the
lsscsi commands may help to find if any are attached to a running system.
There is also a SCSI device driver which offers alternate generic access to SCSI devices. It uses names
of the form /dev/sg<num> where <num> starts at zero. The "lsscsi -g" command may be useful in finding
these and which generic name corresponds to a device type name (e.g. /dev/sg2 may correspond to
/dev/sda). In the lk 2.6 series a block SCSI generic driver was introduced and its names are of the form
/dev/bsg/<h:c:t:l> where h, c, t and l are numbers. Again see the lsscsi command to find the
correspondence between that SCSI tuple (i.e. <h:c:t:l>) and alternate device names.
Prior to the Linux kernel 2.6 series these utilities could only use generic device names (e.g. /dev/sg1
). In almost all cases in the Linux kernel 2.6 series, any device name can be used by these utilities.
WINDOWS DEVICE NAMING
Storage and related devices can have several device names in Windows. Probably the most common in the
volume name (e.g. "D:"). There are also a "class" device names such as "PhysicalDrive<n>", "CDROM<n>" and
"TAPE<n>". <n> is an integer starting at 0 allocated in ascending order as devices are discovered (and
sometimes rediscovered).
Some storage devices have a SCSI lower level device name which starts with a SCSI (pseudo) adapter name
of the form "SCSI<n>:". To this is added sub-addressing in the form of a "bus" number, a "target"
identifier and a LUN (Logical Unit Number). The "bus" number is also known as a "PathId". These are
assembled to form a device name of the form: "SCSI<n>:<bus>,<target>,<lun>". The trailing ",<lun>" may be
omitted in which case a LUN of zero is assumed. This lower level device name cannot often be used
directly since Windows blocks attempts to use it if a class driver has "claimed" the device. There are
SCSI device types (e.g. Automation/Drive interface type) for which there is no class driver. At least
two transports ("bus types" in Windows jargon): USB and IEEE 1394 do not have a "scsi" device names of
this form.
In keeping with DOS file system conventions, the various device names can be given in upper, lower or
mixed case. Since "PhysicalDrive<n>" is tedious to write, a shortened form of "PD<n>" is permitted by all
utilities in this package.
A single device (e.g. a disk) can have many device names. For example: "PD0" can also be "C:", "D:" and
"SCSI0:0,1,0". The two volume names reflect that the disk has two partitions on it. Disk partitions that
are not recognized by Windows are not usually given a volume name. However Vista does show a volume name
for a disk which has no partitions recognized by it and when selected invites the user to format it
(which may be rather unfriendly to other OSes).
These utilities assume a given device name is in the Win32 device namespace. To make that explicit
"\\.\" can be prepended to the device names mentioned in this section. Beware that backslash is an escape
character in Unix like shells and the C programming language. In a shell like Msys (from MinGW) each
backslash may need to be typed twice.
The sg_scan utility within this package lists out Windows device names in a form that is suitable for
other utilities in this package to use.
FREEBSD DEVICE NAMING
SCSI disks have block names of the form /dev/da<num> where <num> is an integer starting at zero. The "da"
is replaced by "sa" for SCSI tape drives and "cd" for SCSI CD/DVD/BD drives. Each SCSI device has a
corresponding pass-through device name of the form /dev/pass<num> where <num> is an integer starting at
zero. The "camcontrol devlist" command may be useful for finding out which SCSI device names are
available and the correspondence between between class and pass-through names.
SOLARIS DEVICE NAMING
SCSI device names below the /dev directory have a form like: c5t4d3s2 where the number following "c" is the controller (HBA) number, the number following "t" is the target number (from the SCSI parallel interface days) and the number following "d" is the LUN. Following the "s" is the slice number which is related to a partition and by convention "s2" is the whole disk. OpenSolaris also has a c5t4d3p2 form where the number following the "p" is the partition number apart from "p0" which is the whole disk. So a whole disk may be referred to as either c5t4d3, c5t4d3s2 or c5t4d3p0 . And these device names are duplicated in the /dev/dsk and /dev/rdsk directories. The former is the block device name and the latter is for "raw" (or char device) access which is what sg3_utils needs. So in OpenSolaris something of the form 'sg_inq /dev/rdsk/c5t4d3p0' should work. If it doesn't work then add a '-vvv' option for more debug information. Trying this form 'sg_inq /dev/dsk/c5t4d3p0' (note "rdsk" changed to "dsk") will result in an "inappropriate ioctl for device" error. The device names within the /dev directory are typically symbolic links to much longer topological names in the /device directory. In Solaris cd/dvd/bd drives seem to be treated as disks and so are found in the /dev/rdsk directory. Tape drives appear in the /dev/rmt directory. There is also a sgen (SCSI generic) driver which by default does not attach to any device. See the /kernel/drv/sgen.conf file to control what is attached. Any attached device will have a device name of the form /dev/scsi/c5t4d3 . Listing available SCSI devices in Solaris seems to be a challenge. "Use the 'format' command" advice works but seems a very dangerous way to list devices. [It does prompt again before doing any damage.] 'devfsadm -Cv' cleans out the clutter in the /dev/rdsk directory, only leaving what is "live". The "cfgadm -v" command looks promising.
EXIT STATUS
To aid scripts that call these utilities, the exit status is set to indicate success (0) or failure (1 or
more). Note that some of the lower values correspond to the SCSI sense key values. The exit status values
are:
0 success
1 syntax error. Either illegal command line options, options with bad arguments or a combination of
options that is not permitted.
2 the DEVICE reports that it is not ready for the operation requested. The device may be in the
process of becoming ready (e.g. spinning up but not at speed) so the utility may work after a
wait.
3 the DEVICE reports a medium or hardware error (or a blank check). For example an attempt to read a
corrupted block on a disk will yield this value.
5 the DEVICE reports an "illegal request" with an additional sense code other than "invalid command
operation code". This is often a supported command with a field set requesting an unsupported
capability. For commands that require a "service action" field this value can indicate that the
command with that service action value is not supported.
6 the DEVICE reports a "unit attention" condition. This usually indicates that something unrelated
to the requested command has occurred (e.g. a device reset) potentially before the current SCSI
command was sent. The requested command has not been executed by the device. Note that unit
attention conditions are usually only reported once by a device.
9 the DEVICE reports an illegal request with an additional sense code of "invalid command operation
code" which means that it doesn't support the requested command.
11 the DEVICE reports an aborted command. In some cases aborted commands can be retried immediately
(e.g. if the transport aborted the command due to congestion).
15 the utility is unable to open, close or use the given DEVICE. The given file name could be
incorrect or there may be permission problems. Adding the '-v' option may give more information.
20 the DEVICE reports it has a check condition but "no sense" and non-zero information in its
additional sense codes. Some polling commands (e.g. REQUEST SENSE) can receive this response.
21 the DEVICE reports a "recovered error". The requested command was successful. Most likely a
utility will report a recovered error to stderr and continue, probably leaving the utility with an
exit status of 0 .
33 the command sent to DEVICE has timed out.
97 a SCSI command response failed sanity checks.
98 the DEVICE reports it has a check condition but the error doesn't fit into any of the above
categories.
99 any errors that can't be categorized into values 1 to 98 may yield this value. This includes
transport and operating system errors after the command has been sent to the device.
Most of the error conditions reported above will be repeatable (an example of one that is not is "unit
attention") so the utility can be run again with the '-v' option (or several) to obtain more information.
COMMON OPTIONS
Arguments to long options are mandatory for short options as well. In the short form an argument to an
option uses zero or more spaces as a separator (i.e. the short form does not use "=" as a separator).
If an option takes a numeric argument then that argument is assumed to be decimal unless otherwise
indicated (e.g. with a leading "0x", a trailing "h" or as noted in the usage message).
Some options are used uniformly in most of the utilities in this package. Those options are listed below.
Note that there are some exceptions.
-h, -?, --help
output the usage message then exit. In a few older utilities the '-h' option requests hexadecimal
output. In these cases the '-?' option will output the usage message then exit.
-H, --hex
for SCSI commands that yield a non-trivial response, print out that response in ASCII hexadecimal.
-m, --maxlen=LEN
several important SCSI commands (e.g. INQUIRY and MODE SENSE) have response lengths that vary
depending on many factors, only some of which these utilities take into account. The maximum
response length is typically specified in the 'allocation length' field of the cdb. In the absence
of this option, several utilities use a default allocation length (sometimes recommended in the
SCSI draft standards) or a "double fetch" strategy. See sg_logs(8) for its description of a
"double fetch" strategy. These techniques are imperfect and in the presence of faulty SCSI targets
can cause problems (e.g. some USB mass storage devices freeze if they receive an INQUIRY
allocation length other than 36). Also use of this option disables any "double fetch" strategy
that may have otherwise been used.
-r, --raw
for SCSI commands that yield a non-trivial response, output that response in binary to stdout. If
any error messages or warning are produced they are usually sent to stderr. Some utilities that
consume data to send to the device along with the SCSI command, use this option to provide that
data or indicate that it can be read from stdin.
-v, --verbose
increase the level of verbosity, (i.e. debug output). Can be used multiple times to further
increase verbosity. The additional output is usually sent to stderr.
-V, --version
print the version string and then exit. Each utility has its own version number and date of last
code change.
NUMERIC ARGUMENTS
Many utilities have command line options that take numeric arguments. These numeric arguments can be
large values (e.g. a logical block address (LBA) on a disk) and can be inconvenient to enter in the
default decimal representation. So various other representations are permitted.
Multiplicative suffixes are accepted. They are one, two or three letter strings appended directly after
the number to which they apply:
c C *1
w W *2
b B *512
k K KiB *1024
KB *1000
m M MiB *1048576
MB *1000000
g G GiB *(2^30)
GB *(10^9)
t T TiB *(2^40)
TB *(10^12)
p P PiB *(2^50)
PB *(10^15)
An example is "2k" for 2048. The large tera and peta suffixes are only available for numeric arguments
that might require 64 bits to represent internally.
A suffix of the form "x<n>" multiplies the leading number by <n>. An example is "2x33" for "66". The
leading number cannot be "0" (zero) as that would be interpreted as a hexadecimal number (see below).
These multiplicative suffixes are compatible with GNU's dd command (since 2002) which claims compliance
with SI and with IEC 60027-2.
Alternatively numerical arguments can be given in hexadecimal. There are two syntaxes. The number can be
preceded by either "0x" or "0X" as found in the C programming language. The second hexadecimal
representation is a trailing "h" or "H" as found in (storage) standards. When hex numbers are given,
multipliers cannot be used. For example the decimal value "256" can be given as "0x100" or "100h".
SCRIPTS, EXAMPLES and UTILS
There are several bash shell scripts in the 'scripts' subdirectory that invoke compiled utilities (e.g.
sg_readcap). The scripts start with 'scsi_' rather than 'sg_'. One purpose of these scripts is to call
the same utility (e.g. sg_readcap) on multiple disks. Most of the basic compiled utilities only allow one
device as an argument. Some distributions install these scripts in a visible directory (e.g.
/usr/src/bin). Some of these scripts have man page entries. See the README file in the 'scripts'
subdirectory.
There is some example C code plus examples of complex invocations in the 'examples' subdirectory. There
is also a README file. The example C may be a simpler example of how to use a SCSI pass-through in Linux
than the main utilities (found in the 'src' subdirectory). This is due to the fewer abstraction layers
(e.g. they don't worry the MinGW in Windows may open a file in text rather than binary mode).
Some utilities that the author has found useful have been placed in the 'utils' subdirectory.
WEB SITE
There is a web page discussing this package at http://sg.danny.cz/sg/sg3_utils.html . The device naming used by this package on various operating systems is discussed at: http://sg.danny.cz/sg/device_name.html .
AUTHORS
Written by Douglas Gilbert. Some utilities have been contributed, see the CREDITS file and individual
source files (in the 'src' directory).
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 1999-2013 Douglas Gilbert
Some utilities are distributed under a GPL version 2 license while others, usually more recent ones, are
under a FreeBSD license. The files that are common to almost all utilities and thus contain the most
reusable code, namely sg_lib.[hc], sg_cmds_basic.[hc] and sg_cmds_extra.[hc] are under a FreeBSD license.
There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sdparm(sdparm), ddpt(ddpt), lsscsi(lsscsi), dmesg(1), mt(1)