Ubuntu Manpage: ssldump - dump SSL traffic on a network

NAME

       ssldump - dump SSL traffic on a network

SYNOPSIS

       ssldump [ -vTshVq -aAdeHnNqTxXvy ] [ -i interface ]
               [ -k keyfile ] [ -p password ] [ -r dumpfile ]
               [ -S [crypto|d|ht|H|nroff] ] [ expression ]

DESCRIPTION

ssldump is an SSL/TLS network protocol analyzer. It identifies TCP connections on the
chosen network interface and attempts to interpret them as SSL/TLS traffic. When it
identifies SSL/TLS traffic, it decodes the records and displays them in a textual form to
stdout. If provided with the appropriate keying material, it will also decrypt the
connections and display the application data traffic.

ssldump has been tested on FreeBSD, Linux, Solaris, and HP/UX. Since it's based on PCAP,
it should work on most platforms. However, unlike tcpdump, ssldump needs to be able to see
both sides of the data transmission so you may have trouble using it with network taps
such as SunOS nit that don't permit you to see transmitted data. Under SunOS with nit or
bpf: To run tcpdump you must have read access to /dev/nit or /dev/bpf*. Under Solaris
with dlpi: You must have read access to the network pseudo device, e.g. /dev/le. Under
HP-UX with dlpi: You must be root or it must be installed setuid to root. Under IRIX with
snoop: You must be root or it must be installed setuid to root. Under Linux: You must be
root or it must be installed setuid to root. Under Ultrix and Digital UNIX: Once the
super-user has enabled promiscuous-mode operation using pfconfig(8), any user may run
ssldump Under BSD: You must have read access to /dev/bpf*.

OPTIONS

-a Print bare TCP ACKs (useful for observing Nagle behavior)

-A Print all record fields (by default ssldump chooses the most interesting fields)

-d Display the application data traffic. This usually means decrypting it, but when -d
is used ssldump will also decode application data traffic before the SSL session
initiates. This allows you to see HTTPS CONNECT behavior as well as SMTP STARTTLS.
As a side effect, since ssldump can't tell whether plaintext is traffic before the
initiation of an SSL connection or just a regular TCP connection, this allows you
to use ssldump to sniff any TCP connection. ssldump will automatically detect
ASCII data and display it directly to the screen. non-ASCII data is displayed as
hex dumps. See also -X.

-e Print absolute timestamps instead of relative timestamps

-H Print the full SSL packet header.

-n Don't try to resolve host names from IP addresses

-N Attempt to parse ASN.1 when it appears, such as in certificates and DNs.

-p Use password as the SSL keyfile password.

-P Don't put the interface into promiscuous mode.

-q Don't decode any record fields beyond a single summary line. (quiet mode).

-T Print the TCP headers.

-v Display version and copyright information.

-x Print each record in hex, as well as decoding it.

-X When the -d option is used, binary data is automatically printed in two columns
with a hex dump on the left and the printable characters on the right. -X
suppresses the display of the printable characters, thus making it easier to cut
and paste the hex data into some other program.

-y Decorate the output for processing with nroff/troff. Not very useful for the
average user.

-i interface
Use interface as the network interface on which to sniff SSL/TLS traffic.

-k keyfile
Use keyfile as the location of the SSL keyfile (OpenSSL format) Previous versions
of ssldump automatically looked in ./server.pem. Now you must specify your keyfile
every time.

-p password
Use password as the SSL keyfile password.

-r file
Read data from file instead of from the network. The old -f option still works but
is deprecated and will probably be removed with the next version.

-S [ crypto | d | ht | H ]
Specify SSL flags to ssldump. These flags include:

crypto Print cryptographic information.

d Print fields as decoded.

ht Print the handshake type.

H Print handshake type and highlights.

expression
Selects what packets ssldump will examine. Technically speaking, ssldump supports
the full expression syntax from PCAP and tcpdump. In fact, the description here is
cribbed from the tcpdump man page. However, since ssldump needs to examine full TCP
streams, most of the tcpdump expressions will select traffic mixes that ssldump
will simply ignore. Only the expressions which don't result in incomplete TCP
streams are listed here.

The expression consists of one or more primitives. Primitives usually consist of
an id (name or number) preceded by one or more qualifiers. There are three
different kinds of qualifier:

type qualifiers say what kind of thing the id name or number refers to. Possible
types are host, net and port. E.g., `host foo', `net 128.3', `port 20'. If
there is no type qualifier, host is assumed.

dir qualifiers specify a particular transfer direction to and/or from id.
Possible directions are src, dst, src or dst and src and dst. E.g., `src
foo', `dst net 128.3', `src or dst port ftp-data'. If there is no dir
qualifier, src or dst is assumed. For `null' link layers (i.e. point to
point protocols such as slip) the inbound and outbound qualifiers can be
used to specify a desired direction.

More complex filter expressions are built up by using the words and, or and not to
combine primitives. E.g., `host foo and not port ftp and not port ftp-data'. To
save typing, identical qualifier lists can be omitted. E.g., `tcp dst port ftp or
ftp-data or domain' is exactly the same as `tcp dst port ftp or tcp dst port ftp-
data or tcp dst port domain'.

Allowable primitives are:

dst host host
True if the IPv4/v6 destination field of the packet is host, which may be
either an address or a name.

src host host
True if the IPv4/v6 source field of the packet is host.

host host
True if either the IPv4/v6 source or destination of the packet is host. Any
of the above host expressions can be prepended with the keywords, ip, arp,
rarp, or ip6 as in:
ip host host
which is equivalent to:
ether proto \ip and host host
If host is a name with multiple IP addresses, each address will be checked
for a match.

ether dst ehost
True if the ethernet destination address is ehost. Ehost may be either a
name from /etc/ethers or a number (see ethers(3N) for numeric format).

ether src ehost
True if the ethernet source address is ehost.

ether host ehost
True if either the ethernet source or destination address is ehost.

gateway host
True if the packet used host as a gateway. I.e., the ethernet source or
destination address was host but neither the IP source nor the IP
destination was host. Host must be a name and must be found in both
/etc/hosts and /etc/ethers. (An equivalent expression is
ether host ehost and not host host
which can be used with either names or numbers for host / ehost.) This
syntax does not work in IPv6-enabled configuration at this moment.

dst net net
True if the IPv4/v6 destination address of the packet has a network number
of net. Net may be either a name from /etc/networks or a network number (see
networks(4) for details).

src net net
True if the IPv4/v6 source address of the packet has a network number of
net.

net net
True if either the IPv4/v6 source or destination address of the packet has a
network number of net.

net net mask mask
True if the IP address matches net with the specific netmask. May be
qualified with src or dst. Note that this syntax is not valid for IPv6 net.

net net/len
True if the IPv4/v6 address matches net a netmask len bits wide. May be
qualified with src or dst.

dst port port
True if the packet is ip/tcp, ip/udp, ip6/tcp or ip6/udp and has a
destination port value of port. The port can be a number or a name used in
/etc/services (see tcp(4P) and udp(4P)). If a name is used, both the port
number and protocol are checked. If a number or ambiguous name is used,
only the port number is checked (e.g., dst port 513 will print both
tcp/login traffic and udp/who traffic, and port domain will print both
tcp/domain and udp/domain traffic).

src port port
True if the packet has a source port value of port.

port port
True if either the source or destination port of the packet is port. Any of
the above port expressions can be prepended with the keywords, tcp or udp,
as in:
tcp src port port
which matches only tcp packets whose source port is port.

Primitives may be combined using:

A parenthesized group of primitives and operators (parentheses are special
to the Shell and must be escaped).

Negation (`!' or `not').

Concatenation (`&&' or `and').

Alternation (`||' or `or').

Negation has highest precedence. Alternation and concatenation have equal
precedence and associate left to right. Note that explicit and tokens, not
juxtaposition, are now required for concatenation.

If an identifier is given without a keyword, the most recent keyword is assumed.
For example,
not host vs and ace
is short for
not host vs and host ace
which should not be confused with
not ( host vs or ace )

Expression arguments can be passed to ssldump as either a single argument or as
multiple arguments, whichever is more convenient. Generally, if the expression
contains Shell metacharacters, it is easier to pass it as a single, quoted
argument. Multiple arguments are concatenated with spaces before being parsed.

EXAMPLES

       To listen to traffic on interface le0 port 443
              ssldump -i le0 port 443

       To listen to traffic to the server romeo on port 443.
              ssldump -i le0 port 443 and host romeo

       To decrypt traffic to to host romeo server.pem and the password foobar
              ssldump -Ad -k ~/server.pem -p foobar -i le0 host romeo

OUTPUT FORMAT

All output is printed to standard out.

ssldump prints an indication of every new TCP connection using a line like the following

New TCP connection #2: iromeo.rtfm.com(2302) <-> sr1.rtfm.com(4433)

The host which send the first SYN is printed on the left and the host which responded is
printed on the right. Ordinarily, this means that the SSL client will be printed on the
left with the SSL server on the right. In this case we have a connection from
iromeo.rtfm.com (port 2303) to sr1.rtfm.com (port 4433). To allow the user to disentangle
traffic from different connections, each connection is numbered. This is connection 2.

The printout of each SSL record begins with a record line. This line contains the
connection and record number, a timestamp, and the record type, as in the following:

2 3 0.2001 (0.0749) S>C Handshake Certificate

This is record 3 on connection 2. The first timestamp is the time since the beginning of
the connection. The second is the time since the previous record. Both are in seconds.

The next field in the record line is the direction that the record was going. C>S
indicates records transmitted from client to server and S>C indicates records transmitted
from server to client. ssldump assumes that the host to transmit the first SYN is the SSL
client (this is nearly always correct).

The next field is the record type, one of Handshake, IAlert, ChangeCipherSpec, or
application_data. Finally, ssldump may print record-specific data on the rest of the line.
For Handshake records, it prints the handshake message. Thus, this record is a Certificate
message.

ssldump chooses certain record types for further decoding. These are the ones that have
proven to be most useful for debugging:

ClientHello - version, offered cipher suites, session id
if provided)
ServerHello - version, session_id, chosen cipher suite,
compression method
Alert - type and level (if obtainable)

Fuller decoding of the various records can be obtained by using the -A , -d , -k and -p
flags.

DECRYPTION

       ssldump can decrypt traffic between two hosts if the following two conditions are met:
              1. ssldump has the keys.
              2. Static RSA was used.
       In  any  other  case,  once  encryption starts, ssldump will only be able to determine the
       record type. Consider the following section of a trace.

       1 5  0.4129 (0.1983)  C>S  Handshake      ClientKeyExchange
       1 6  0.4129 (0.0000)  C>S  ChangeCipherSpec
       1 7  0.4129 (0.0000)  C>S  Handshake
       1 8  0.5585 (0.1456)  S>C  ChangeCipherSpec
       1 9  0.6135 (0.0550)  S>C  Handshake
       1 10 2.3121 (1.6986)  C>S  application_data
       1 11 2.5336 (0.2214)  C>S  application_data
       1 12 2.5545 (0.0209)  S>C  application_data
       1 13 2.5592 (0.0046)  S>C  application_data
       1 14 2.5592 (0.0000)  S>C  Alert

       Note that the ClientKeyExchange message type is printed but  the  rest  of  the  Handshake
       messages  do  not  have  types.  These  are  the  Finished  messages, but because they are
       encrypted ssldump only knows that they are of type Handshake.  Similarly, had the Alert in
       record  14  happened  during  the  handshake, it's type and level would have been printed.
       However, since it is encrypted we can only tell that it is an alert.

BUGS

       Please send bug reports to ssldump@rtfm.com.

       The TCP reassembler is not perfect. No attempt is made to reassemble IP fragments and  the
       3-way  handshake  and close handshake are imperfectly implemented. In practice, this turns
       out not to be much of a problem.

       Support is provided for only for Ethernet and loopback interfaces because that's all  that
       I  have. If you have another kind of network you will need to modify pcap_cb in base/pcap-
       snoop.c. If you have direct experience with ssldump on  other  networks,  please  send  me
       patches.

       ssldump doesn't implement session caching and therefore can't decrypt resumed sessions.

AUTHOR

       ssldump was written by Eric Rescorla <ekr@rtfm.com>.

                                        28 September 2001                              SSLDUMP(1)