Ubuntu Manpage: sockd.conf - SOCKS server configuration file

Provided by: socks4-server_4.3.beta2-18_amd64

NAME

       sockd.conf - SOCKS server configuration file

SYNOPSIS

       /etc/sockd.conf

DESCRIPTION

The file /etc/sockd.conf is used to control access to SOCKS proxy server sockd and its
services. (See sockd(8).) Permission and denial of a service request can be decided based
on various combinations of the requesting host, the destination host, the type of service
(destination port number), as well as the requesting user. A line in /etc/sockd.conf can
be up to 1023 characters long. Each line may contain the following fields in the
indicated order:

action [?=use_identd] [*=userlist] src_addr src_mask [dst_addr dst_mask] [op dst_port] [
: shell_cmd ]

Spaces and tabs separate the fields. Fields enclosed in square brackets are optional.
Blank lines are allowed. Except for lines that start with #NO_IDENTD: or #BAD_ID:,
everything from the first appearance of # to the end of the line is considered comment and
thus ignored by sockd during normal validation.

The action field must be either permit or deny and indicates the action to be taken if a
request matches the conditions specified in that line.

The use_identd field, when present, must be I, i, or n, and is used to specify whether
identd verification should be employed for the current line. ?=I demands the use of identd
for verifying the user's identity, denying access if connection to client's identd fails
or if the result does not match the user-id reported by the client program. ?=i also
specifies the use of identd, but denies access only if client's identd reports a user-id
different from what the client program claims. ?=n turns off the use of identd. For the
line in which these fields are used, they override the global identd setting, which is
determined by options -I and -i on the sockd command line.

The userlist field, when present, consists of one or more user-ids or filenames, with
comma as separator. No spaces or tabs are allowed in the list. The user-ids should be ids
of users on the requesting host, not those on the destination host or the SOCKS server
host. The filenames must be full pathnames with the leading /. Inside the specified
files, user-ids may be listed one or several per line, with any combination of blanks,
tabs, and commas as separators. The appearance of # marks the remainder of the line as
comment. Each line in the files may be up to 1023 characters long. If the *=userlist
field is omitted, the line applies to all user-ids.

The src_addr and dst_addr fields either specify IP addresses of hosts, networks, or
subnets in the usual dotted form, e.g., 129.201.4.0, or a domain name, e.g., internic.net.
The src_mask and dst_mask fields are masks for the corresponding IP addresses. Bits in
these masks that are set to 0 indicate the bit positions to be ignored during comparisons
of IP addresses. So, specifying 255.255.255.255 in the mask demands an exact match with
the specified IP address field, whereas 0.0.0.0 in the mask causes a match no matter what
IP address is specified. The contents of the mask fields are ignore, though they must
still be supplied (use 0.0.0.0), if domain names are used for the corresponding address
fields. If the domain name starts with a period, it specifies a zone and matches all
domain names within that zone, otherwise it matches only the domain name itself. For
example, xyz.com matches only xyz.com, while .xyz.com matches not only xyz.com, but also
abc.xyz.com and this.and.that.xyz.com, among others. The special symbol ALL (which must be
entirely in uppercase) matches everything. Domain names are otherwise case-insensitive.

If the dst_addr dst_mask pair is omitted, the line applies to all destination hosts.

The op field must be eq, neq, lt, gt, le, or ge, for the condition of equal, not equal,
less than, greater than, less than or equal, and greater than or equal, respectively. The
dst_port field can be either a port number, e.g., 23, or the equivalent service name as
specified in the file /etc/services, e.g., telnet for port number 23. If this pair is
omitted, the line applies to all services, i.e., all destination port numbers.

For example, consider the line

permit *=root,clivep 128.103.4.10 255.255.255.255 179.200.20.0 255.255.255.0 le 1023

To match the conditions indicated in this line, a request must come from a user named
'root' or 'clivep' on the host whose IP address is 128.103.4.10 exactly, the destination
host must have 179.200.20 in the first three bytes of its IP address (the last byte
doesn't matter), and the service must use a port number less than or equal to 1023 on the
destination host. Since the action field is permit, such requests will be granted.

When a request is received by sockd, it checks against the lines in file /etc/sockd.conf,
one line at a time. Once it finds a line with conditions that are matched by the request,
the request is either granted or denied based on the action field of that line. The
remaining lines of file /etc/sockd.conf are skipped. If no matching line is found in the
entire file, the request is denied.

Be very careful how you order the lines in file /etc/sockd.conf. The following two lines
in the indicated order

deny *=abxyz 128.140.13.24 0.0.0.0
permit 128.140.13.24 0.0.0.0

disallow all requests by user 'abxyz' from host 128.140.13.24, but allow all requests by
other users from the same host. Switch the order of the two lines and even requests by
user 'abxyz' are granted.

The shell_cmd field specifies a command string that is executed when the conditions on
that line are satisfied. The following substitutions occur before the string is presented
to the Borne shell for execution:

%A -- replaced by the client host's domainname if known, by its IP address otherwise
%a -- replaced by the client host's IP address
%c -- replaced by "connect" or "bind", the command sockd is asked to execute
%p -- replaced by the process id of sockd
%S -- replaced by the service name (e.g., ftp) if known, by the destination port number otherwise
%s -- replaced by the destination port number
%U -- replaced by the user-id reported by identd
%u -- replaced by the user-id reported by the client program
%Z -- replaced by the destination host's domainname if known, by its IP address otherwise
%z -- replaced by the destination host's IP address
%% -- replaced by a single %

Several shell commands can be strung together in the usual way. For example,

/usr/ucb/finger @%A | /usr/ucb/mail -s 'SOCKS: rejected %u@%A to %Z (%S)' root root@%A

will finger the client host and pipe the result into an email message for superusers at
the server host and the client host with an appropriate Subject line. Most often this
feature is used with a deny line, but it can be used with permit also.

Although there is an implied 'deny all' at the end of the configuration file, you may
supply one explicitly so as to take some specific action when requests are so rejected,
e.g., (in one continuous line),

deny 0.0.0.0 0.0.0.0 : /usr/ucb/finger @%A |
/usr/ucb/mail -s 'SOCKS: rejected %u@%A to %Z (%S)' root root@%A

You may also specify in /etc/sockd.conf commands to be executed when sockd cannot connect
to client's identd or when the user-ids reported by the client programs and the client's
identd do not match. These special entries must have #NO_IDENTD: and #BAD_ID: at the very
beginning of the line, followed by the shell commands to be executed. For example:

#NO_IDENTD: /usr/ucb/mail -s 'Please run identd on host %A' root@%A
#BAD_ID: finger @%A | /usr/ucb/mail -s '%U pretends to be %u on %A' root root@%A

Strictly speaking, sockd has no concept of inside/outside, it does know which is the
requesting host and which the destination and that is the basis of its access control.
Therefore it can be used to facilitate access from outside world into your internal
networks as well. Needless to say, you have to take extreme caution if you choose to do
so. If you don't need that kind of access, it is recommended that you specifically deny
such connections in sockd.conf. For example, if the Class B IP network 129.1 is your
internal network, use

deny 0.0.0.0 0.0.0.0 129.1.0.0 255.255.0.0

as the first line of your sockd.conf to protect your inside hosts from all attempts of
access from the outside world through SOCKS. If your internal network consists of several
IP networks, you have to use one such line for each of them. In that case, it may be more
convenient to use domain name instead, for instance,

deny 0.0.0.0 0.0.0.0 .myowm.com 0.0.0.0

deny ALL 0.0.0.0 .myown.com 0.0.0.0

may be used, assuming that myown.com is your domain.

Though the use of domain names can be very convenient and can also reduce start-up
overhead by reducing the number of lines in the configuration file, you should be very
careful with your DNS (Domain Name System) setup. Here are some details that you should
know.

The original information the SOCKS server has of the source or the destination host is in
the form of its IP address. The SOCKS server does a reverse DNS lookup to find the domain
name correspodning to that IP address. It then does a normal DNS loopkup to translate the
domain name back to an IP address. If the two IP addresses match, the SOCKS server
retains both the domain name and the IP address as identifier of the host, and will use
whichever as appropriate when it checkes the configuration file. If either of the two DNS
lookups fails or if the two IP addresses do not match, SOCKS server retains only the
original IP address as the only identifier of the host, with the consequence that it will
not match any line in the configuration file which specifies a domain name (other than
ALL) in the corresponding address field.

Suppose now you add a new host to your internal network before updating your nameserver's
data with both the A record and the PTR record of the new host. When the SOCKS server
receives a request with the IP address of the new host as its destination, at least one of
the DNS lookups will fail. Consequently it will not be protected by lines in which the
domain name is used in the destination address field.

So, if you want to use domain name in the configuration file, be very sure that you always
keep your DNS information up-to-date. It's probably a good idea to update your DNS data
before adding a new host to your network. Also make sure that your SOCKS server always
queries a nameserver which has the most up-to-date information of your internal network.

You have the option of using the frozen configuration file /etc/sockd.fc instead of
/etc/sockd.conf. The frozen file is produced by make_sockdfc and is essentially the
memeory image of the parsed configuration file. Using it can reduce the start-up delay of
the SOCKS server since it eliminates the need for parsing.

When the SOCKS server starts, it always looks for the frozen configuration first and
reverts to the unfrozen version only if no frozen configuration is found. All
modifications to the configuration must be done on the plain-text, unfrozen file. Be sure
that you run make_sockdfc every time after you modify /etc/sockd.conf or your SOCKS server
would be using the frozen version of an older configuration.

NAME

SYNOPSIS

DESCRIPTION

SEE ALSO