NAME

       avmcapictrl - Add, reset or remove active AVM cards and load firmware

SYNOPSIS

       avmcapictrl add <portbase> <irq> <type>
       avmcapictrl load <bootcode> [<contrnr> [<protocol>
           [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]]
       avmcapictrl reset [contrnr]
       avmcapictrl remove [contrnr]
       avmcapictrl trace [contrnr] [off|short|on|full|shortnodata|nodata]
       avmcapictrl addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]

DESCRIPTION

       avmcapictrl  is  used  to  register  active  AVM  ISA  cards  to the kernelcapi system and
       therewith to the ISDN system. You need it also to upload the firmware to  any  active  AVM
       card.  If  an  error  occurs please also check the kernel error messages using the command
       dmesg(8).

COMMANDS

       add <portbase> <irq> <type>
            is used to add an ISA card to the kernel-capi2.0 system.  The portbase can  have  the
            values  0x150, 0x250, 0x300 and 0x340 for the B1 ISA cards, look at the jumper on the
            card.  For a T1-ISA (HEMA) card you can select a wide range of ports.
            irq can be selected from the following values:
            3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
            type can be B1 or T1.

       load <bootcode> [<contrnr> [<protocol>
            [P2P | <dn1>:<spid1> [<dn2>:<spid2>]]]] is used  to  load  the  firmware  to  a  card
            bootcode  is  a  t4-file.  The  actual  versions  of the t4-files for the different D
            channel protocols can be found at ftp://ftp.in-berlin.de/pub/capi4linux/firmware/b1/
            You need different t4-files for different D channel protocols: b1-1tr6.t4  for  1TR6,
            b1.t4 for DSS1 and
            b1-usa.t4 for 5ESS and NI1 (DSS1 is also supported).
            For  M1/M2  PCMCIA  cards  you need m1-s10.t4 or m1-s4.t4 depending on the handy type
            used.
            contrnr is the number of the controller (card) starting from 1.
            protocol can be DSS1, CT1, VN3, AUSTEL, 5ESS or NI1.
            P2P point to point
            DN1:SPID1 DN2:SPID2 is for the american protocols 5ESS and NI1.

       reset [contrnr]
            is used to reset a card if loading has failed.  This function only makes sense  if  a
            card is not successfully loaded.
            contrnr is the number of the controller (card) starting from 1.

       remove [contrnr]
            is  used  to  remove  a  card  previously  added.  You  can  also  remove cards added
            automatically (for example a B1-PCI card).
            contrnr is the number of the controller (card) starting from 1.

       trace [contrnr] [off|short|on|full|shortnodata|nodata]
            is used to trace CAPI2.0 messages. The trace will be done  as  kernel  messages,  see
            dmesg(8).
            contrnr is the number of the controller (card) starting from 1.
            off switch off tracing
            short switch on "one line per CAPI2.0 message" tracing
            on | full switch on "full decode" tracing
            shortnodata switch on "one line per CAPI2.0 message" tracing, but exclude DATA_B3_IND
            and DATA_B3_REQ messages.
            on | full switch on full decode tracing,  but  exclude  DATA_B3_IND  and  DATA_B3_REQ
            messages.

       addcard <driver> <portbase> <irq> [ <membase> [ <cardnr> ] ]
            is used to add a card, this is more generic than add.
            driver currently b1isa or t1isa
            portbase can have the values 0x150, 0x250, 0x300 and 0x340 for the b1isa driver, look
            at the jumper on the card.  For t1isa driver you can select an wide range of ports.
            irq can be selected from the following values: 3, 4, 5, 6, 7, 9, 10, 11, 12 and 15.
            membase memory address if needed by driver
            cardnr only useful with driver t1isa

AUTHOR

       Carsten Paeth <calle@calle.in-berlin.de>

SEE ALSO

       ttyI(4), isdnctrl(8), isdninfo(4).  dmesg(8).  syslogd(8).