Provided by: gdnsd_1.11.1-1_amd64 
NAME
gdnsd-plugin-metafo - gdnsd plugin for address meta-failover
SYNOPSIS
Minimal example gdnsd config file using this plugin:
plugins => {
metafo => {
resources => {
prod_www => {
datacenters => [ dc-01, dc-02, dc-03 ]
dcmap => {
dc-01 => 192.0.2.1
dc-02 => { lb01 => 192.0.2.2, lb02 => 192.0.2.3 }
dc-03 => [ 192.0.2.4, 192.0.2.5, 192.0.2.6 ]
}
}
}
}
}
Example zonefile RRs:
www 600 DYNA metafo!prod_www
www-dc01 600 DYNA metafo!prod_www/dc-01
DESCRIPTION
gdnsd-plugin-metafo is a meta-plugin. It does static-ordered address failover between
multiple "datacenters" (which may or may not correspond with real datacenters, it's just a
convenient label). Each datacenter is defined in terms of other plugins such as
"multifo", "weighted", etc, as described below.
CONFIGURATION - TOP-LEVEL
The top level of the metafo plugin's configuration (i.e. "plugins => { metafo => { ... }
}") supports only one fixed, required key, "resources", whose value must be a hash. The
contents of "resources" is a key per named resource, with the value defining that
resource.
Any other keys present at the top level will be inherited down inside of each per-resource
hash inside the "resources" stanza, acting as per-resource defaults for anything not
defined explicitly there, as explained below.
CONFIGURATION - RESOURCES
All keys within the resources stanza represent named resources, which can be referenced by
"DYNA" RRs in zonefiles (e.g. "www DYNA metafo!resource_name"). Each resource's value
must be a key-value hash configuring the resource itself. Lightweight structural example:
plugins => {
metafo => {
resources => { resA => { ... }, resB => { ... } }
}
}
Within a resource, there are only two specifically meaningful keys:
"datacenters = [ A, B, C, ... ]"
Array of datacenter names, required. This is the set of datacenter name labels used
for this resource, in the order they will be checked for failover.
"dcmap = { ... }"
Hash, required. The "dcmap" is a key-value hash where the keys must be exactly the
list of datacenters defined in this resource's "datacenters" list, and the values
defined the address configuration of each datacenter. Another minimal structural
example down to this level:
plugins => {
metafo => {
resources => {
resA => {
datacenters => [ dc01, dc02 ],
dcmap => {
dc01 => ???
dc02 => ???
}
}
}
}
}
There are several forms the per-datacenter values ("???" above) can take, documented
in the next section.
Any keys other than "datacenters" and "dcmap" at the per-resource level serve as inherited
defaults for each per-datacenter configuration inside of the "dcmap".
PER-DATACENTER RESOLUTION
The value of the datacenters within the "dcmap" section of a resource can take several
forms. It is important to understand that for the most part, plugin_metafo does not deal
with this level of results itself, but instead delegates the work at this scope to other
plugins. The most direct and obvious way to do this is with a direct reference of the
form "%plugin!resource", as shown here:
plugins => {
metafo => {
resources => {
resA => {
datacenters => [ dc1, dc2 ],
dcmap => {
dc1 => %multifo!res_mfo1
dc2 => %multifo!res_mfo2
}
}
}
}
multifo => {
res_mfo1 => { lb01 => 192.0.2.1, lb02 => 192.0.2.3 }
res_mfo2 => { lb01 => 192.0.2.111, lb02 => 192.0.2.113 }
}
}
However, to make life simpler in the simple cases, plugin_metafo can synthesize the lower-
level plugin's configuration from a hash, like so:
plugins => {
metafo => {
resources => {
resA => {
datacenters => [ dc1, dc2 ],
dcmap => {
dc1 => { plugin => multifo, lb01 => 192.0.2.1, lb02 => 192.0.2.3 }
dc2 => { lb01 => 192.0.2.111, lb02 => 192.0.2.113 }
# the above are effectively treated as:
# dc1 => %multifo!metafo_resA_dc1
# dc2 => %multifo!metafo_resA_dc2
}
}
}
}
# below does not exist in your configfile, but is what plugin_metafo
# synthesizes to support the above:
#multifo => {
# metafo_resA_dc1 => { lb01 => 192.0.2.1, lb02 => 192.0.2.3 }
# metafo_resA_dc2 => { lb01 => 192.0.2.111, lb02 => 192.0.2.113 }
#}
}
Within a hash like the above, the special key "plugin" will be stripped out internally and
used to name the plugin we synthesize the config for. "plugin" defaults to "multifo" if
not specified. Note that "plugin" could also be specified at the resource level (just
inside of the "resA" stanza) to change the default for all "dcmap" entries in one
resource, and could also be specified at the outer-most scope (just inside the "metafo"
stanza) to change the default for all resources.
The defaulted-down "plugin" is also the default for the direct-reference
"%plugin!resource" form discussed earlier. With the correct default plugin name, it can
be shortened to just "!resource".
The same sort of key-value inheritance scheme (top-level -> per-resource level -> per-
datacenter level) can also be used for any other parameter in synthesized resource
configurations specific to the per-datacenter plugin(s) you are using. A common example
would be the "service_types" parameter that most plugins which support monitored address
results have. Note that these other values (e.g. service_types) would only apply to
synthesized resources, not to direct-references like "%multifo!foo", which must be
configured entirely separately within that plugin's config.
There are two other possible shortcut values for datacenters: a single direct address, or
an array of addresses. If a single IP address or an array of IP addresses are specified,
plugin_metafo will synthesize a hash from them with the plugin forced to "multifo" (since
it cannot know the syntax of hashes for all other plugins, which may differ), and give
them address labels 1, 2, etc.
A much more complete example, showing off most of the features above:
plugins => {
metafo => {
plugin => multifo # change default for all resources
service_types => [ bar ] # default service_types for synthesized below
resources => {
resA => {
plugin => multifo # change default for this resource
service_types => [foo, bar] # services types for synthesized below:
datacenters => [ dc1, dc2, dc3, dc4, dc5, dc6, dc7 ],
dcmap => {
dc1 => { plugin => multifo, lb01 => 192.0.2.1, lb02 => 192.0.2.3 }
dc2 => { lb01 => 192.0.2.111, lb02 => 192.0.2.113 }
dc3 => %simplefo!foo
dc4 => { plugin => simplefo, primary => 192.0.2.100, secondary => 192.0.2.101 }
dc5 => !bar
dc6 => 192.0.2.150
dc7 => [ 192.0.2.180, 192.0.2.181 ]
}
}
}
}
# below, commented-out sections show configuration synthesized
# by plugin_metafo, whereas the rest are direct-references that
# had to be manually specified here:
multifo => {
# metafo_resA_dc1 => { lb01 => 192.0.2.1, lb02 => 192.0.2.3, service_types => [foo, bar] }
# metafo_resA_dc2 => { lb01 => 192.0.2.111, lb02 => 192.0.2.113, service_types => [foo, bar] }
bar => { asd => 192.0.2.77, xyz => 192.0.2.88 }
# metafo_resA_dc6 => { 1 => 192.0.2.150, service_types => [foo, bar] }
# metafo_resA_dc7 => { 1 => 192.0.2.180, 2 => 192.0.2.181, service_types => [foo, bar] }
}
simplefo => {
foo => { primary => 192.0.2.80, secondary => 192.0.2.81 }
# metafo_resA_dc4 => { primary => 192.0.2.100, secondary => 192.0.2.101, service_types => [foo, bar] }
}
}
Note in the example above that "%multifo!bar" and "%simplefo!foo" would have had their
default "service_types = default" rather than the one specified at the metafo level,
because they were not synthesized. It would be up to you to keep all of the service_types
in sync when using direct references.
SYNTHETIC PER-DATACENTER RESOURCES
This plugin will synthesize additional, per-datacenter resource names from your
configuration. They are named as "resname/dcname". For example, if you define a metafo
resource named "prodwww" with the datacenter list "[ pri, sec ]", the resource names
"prodwww/pri" and "prodwww/sec" will be sythesized and can be used in zonefile records,
e.g.:
www-backup 300 DYNA metafo!prodwww/sec
When used, these per-datacenter synthetic resource names cause a given lookup to skip the
normal failover process and directly return results from that particular datacenter.
SEE ALSO
gdnsd.config(5), gdnsd.zonefile(5), gdnsd(8)
The gdnsd manual.
COPYRIGHT AND LICENSE
Copyright (c) 2012 Brandon L Black <blblack@gmail.com>
This file is part of gdnsd.
gdnsd is free software: you can redistribute it and/or modify it under the terms of the
GNU General Public License as published by the Free Software Foundation, either version 3
of the License, or (at your option) any later version.
gdnsd is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without
even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with gdnsd. If
not, see <http://www.gnu.org/licenses/>.