Provided by: util-linux_2.27.1-6ubuntu3.10_amd64 
NAME
sfdisk - display or manipulate a disk partition table
SYNOPSIS
sfdisk [options] device [-N partition-number]
sfdisk [options] command
DESCRIPTION
sfdisk is a script-oriented tool for partitioning any block device.
Since version 2.26 sfdisk supports MBR (DOS), GPT, SUN and SGI disk labels, but no longer
provides any functionality for CHS (Cylinder-Head-Sector) addressing. CHS has never been
important for Linux, and this addressing concept does not make any sense for new devices.
sfdisk (since version 2.26) aligns the start and end of partitions to block-device I/O
limits when relative sizes are specified, or when the default values are used.
sfdisk does not create the standard system partitions for SGI and SUN disk labels like
fdisk(8) does. It is necessary to explicitly create all partitions including whole-disk
system partitions.
COMMANDS
The commands are mutually exclusive.
[-N partition-number] device
The default sfdisk command is to read the specification for the desired
partitioning of device from standard input, and then create a partition table
according to the specification. See below for the description of the input format.
If standard input is a terminal, then sfdisk starts an interactive session.
If the option -N is specified, then the changes are applied to the partition
addressed by partition-number. The unspecified fields of the partition are not
modified.
Note that it's possible to address an unused partition with -N. For example, an
MBR always contains 4 partitions, but the number of used partitions may be smaller.
In this case sfdisk follows the default values from the partition table and does
not use built-in defaults for the unused partition given with -N. See also
---append.
-A, --activate device [partition-number...]
Switch on the bootable flag. If no partition-number is specified, then all
partitions with an enabled flag are listed.
-d, --dump device
Dump the partitions of a device in a format that is usable as input to sfdisk. See
the section BACKING UP THE PARTITION TABLE.
-g, --show-geometry [device...]
List the geometry of all or the specified devices.
-J, --json device
Dump the partitions of a device in JSON format. Note that sfdisk is not able to
use JSON as input format.
-l, --list [device...]
List the partitions of all or the specified devices. This command can be used
together with --verify.
-F, --list-free [device...]
List the free unpartitioned areas on all or the specified devices.
--part-attrs device partno [attrs]
Change the GPT partition attribute bits. If attrs is not specified, then print the
current partition settings. The attrs argument is a comma- or space-delimited list
of bits. The currently supported attribute bits are: RequiredPartiton,
NoBlockIOProtocol, LegacyBIOSBootable and GUID-specific bits in the range from 48
to 63. For example, the string "RequiredPartiton,50,51" sets three bits.
--part-label device partno [label]
Change the GPT partition name (label). If label is not specified, then print the
current partition label.
--part-type device partno [type]
Change the partition type. If type is not specified, then print the current
partition type. The type argument is hexadecimal for MBR, or a GUID for GPT. For
backward compatibility the options -c and --id have the same meaning.
--part-uuid device partno [uuid]
Change the GPT partition UUID. If uuid is not specified, then print the current
partition UUID.
-s, --show-size [device...]
List the sizes of all or the specified devices.
-T, --list-types
Print all supported types for the current disk label or the label specified by
--label.
-V, --verify [device...]
Test whether the partition table and partitions seem correct.
OPTIONS
-a, --append
Don't create a new partition table, but only append the specified partitions.
-b, --backup
Back up the current partition table sectors before starting the partitioning. The
default backup file name is ~/sfdisk-<device>-<offset>.bak; to use another name see
option -O, --backup-file.
--color[=when]
Colorize the output. The optional argument when can be auto, never or always. If
the when argument is omitted, it defaults to auto. The colors can be disabled; for
the current built-in default see the --help output. See also the COLORS section.
-f, --force
Disable all consistency checking.
--Linux
Deprecated and ignored option. Partitioning that is compatible with Linux (and
other modern operating systems) is the default.
-n, --no-act
Do everything except writing to the device.
--no-reread
Do not check through the re-read-partition-table ioctl whether the device is in
use.
-O, --backup-file path
Override the default backup file name. Note that the device name and offset are
always appended to the file name.
-o, --output list
Specify which output columns to print. Use --help to get a list of all supported
columns.
The default list of columns may be extended if list is specified in the format
+list (e.g. -o +UUID).
-q, --quiet
Suppress extra info messages.
-u, --unit S
Deprecated option. Only the sector unit is supported.
-X, --label type
Specify the disk label type (e.g. dos, gpt, ...). If this option is not given,
then sfdisk defaults to the existing label, but if there is no label on the device
yet, then the type defaults to dos.
-Y, --label-nested type
Force editing of a nested disk label. The primary disk label has to exist already.
This option allows to edit for example a hybrid/protective MBR on devices with GPT.
-v, --version
Display version information and exit.
-h, --help
Display help text and exit.
INPUT FORMATS
sfdisk supports two input formats and generic header lines.
Header lines
The optional header lines specify generic information that apply to the partition
table. The header-line format is:
<name>: <value>
The currently recognized headers are:
unit Specify the partitioning unit. The only supported unit is sectors.
label Specify the partition table type. For example dos or gpt.
label-id
Specify the partition table identifier. It should be a hexadecimal
number (with a 0x prefix) for MBR and a UUID for GPT.
Note that it is only possible to use header lines before the first partition is
specified in the input.
Unnamed-fields format
start size type bootable
where each line fills one partition descriptor.
Fields are separated by whitespace, comma or semicolon possibly followed by
whitespace; initial and trailing whitespace is ignored. Numbers can be octal,
decimal or hexadecimal; decimal is the default. When a field is absent, empty or
specified as '-' a default value is used. But when the -N option (change a single
partition) is given, the default for each field is its previous value.
The default value of start is the first non-assigned sector aligned according to
device I/O limits. The default start offset for the first partition is 1 MiB. The
offset may be followed by the multiplicative suffixes (KiB, MiB, GiB, TiB, PiB,
EiB, ZiB and YiB) then the number is interpreted as offset in bytes.
The default value of size indicates "as much as possible"; i.e. until the next
partition or end-of-device. A numerical argument is by default interpreted as a
number of sectors, however if the size is followed by one of the multiplicative
suffixes (KiB, MiB, GiB, TiB, PiB, EiB, ZiB and YiB) then the number is interpreted
as the size of the partition in bytes and it is then aligned according to the
device I/O limits. A '+' can be used instead of a number to enlarge the partition
as much as possible. Note '+' is equivalent to the default behaviour for a new
partition; existing partitions will be resized as required.
The partition type is given in hex for MBR (DOS), without the 0x prefix, a GUID
string for GPT, or a shortcut:
L Linux; means 83 for MBR and 0FC63DAF-8483-4772-8E79-3D69D8477DE4 for
GPT.
S swap area; means 82 for MBR and 0657FD6D-A4AB-43C4-84E5-0933C84B4F4F
for GPT
E extended partition; means 5 for MBR
H home partition; means 933AC7E1-2EB4-4F13-B844-0E14E2AEF915 for GPT
X linux extended partition; means 85 for MBR.
The default type value is L
bootable is specified as [*|-], with as default not-bootable. The value of this
field is irrelevant for Linux - when Linux runs it has been booted already - but ir
might play a role for certain boot loaders and for other operating systems.
Named-fields format
This format is more readable, robust, extendible and allows to specify additional
information (e.g. a UUID). It is recommended to use this format to keep your
scripts more readable.
[device :] name[=value], ...
The device field is optional. sfdiskextracts the partition number from the device
name. It allows to specify the partitions in random order. This functionality is
mostly used by --dump. Don't use it if you are not sure.
The value can be between quotation marks (e.g. name="This is partition name"). The
currently supported fields are:
start=number
The first non-assigned sector aligned according to device I/O limits.
The default start offset for the first partition is 1 MiB. The offset
may be followed by the multiplicative suffixes (KiB, MiB, GiB, TiB,
PiB, EiB, ZiB and YiB) then the number is interpreted as offset in
bytes.
size=number
Specify the partition size in sectors. The number may be followed by
the multiplicative suffixes (KiB, MiB, GiB, TiB, PiB, EiB, ZiB and
YiB), then it's interpreted as size in bytes and the size is aligned
according to device I/O limits.
bootable
Mark the partition as bootable.
attrs=string
Partition attributes, usually GPT partition attribute bits. See
--part-attrs for more details about the GPT-bits string format.
uuid=string
GPT partition UUID.
name=string
GPT partition name.
type=code
A hexadecimal number (without 0x) for an MBR partition, or a GUID for
a GPT partition. For backward compatibility the Id= field has the
same meaning.
BACKING UP THE PARTITION TABLE
It is recommended to save the layout of your devices. sfdisk supports two ways.
Use the --dump option to save a description of the device layout to a text file. The dump
format is suitable for later sfdisk input. For example:
sfdisk --dump /dev/sda > sda.dump
This can later be restored by:
sfdisk /dev/sda < sda.dump
If you want to do a full (binary) backup of all sectors where the partition table is
stored, then use the --backup option. It writes the sectors to
~/sfdisk-<device>-<offset>.bak files. The default name of the backup file can be changed
with the --backup-file option. The backup files contain only raw data from the device.
Note that the same concept of backup files is used by wipefs(8). For example:
sfdisk --backup /dev/sda
The GPT header can later be restored by:
dd if=~/sfdisk-sda-0x00000200.bak of=/dev/sda seek=$((0x00000200)) bs=1
conv=notrunc
Note that sfdisk since version 2.26 no longer provides the -I option to restore sectors.
dd (1) provides all necessary functionality.
COLORS
Implicit coloring can be disabled by an empty file /etc/terminal-colors.d/sfdisk.disable.
See terminal-colors.d(5) for more details about colorization configuration. The logical
color names supported by sfdisk are:
header The header of the output tables.
warn The warning messages.
welcome
The welcome message.
NOTES
Since version 2.26 sfdisk no longer provides the -R or --re-read option to force the
kernel to reread the partition table. Use blockdev --rereadpt instead.
Since version 2.26 sfdisk does not provide the --DOS, --IBM, --DOS-extended, --unhide,
--show-extended, --cylinders, --heads, --sectors, --inside-outer, --not-inside-outer
options.
ENVIRONMENT
SFDISK_DEBUG=all
enables sfdisk debug output.
LIBFDISK_DEBUG=all
enables libfdisk debug output.
LIBBLKID_DEBUG=all
enables libblkid debug output.
LIBSMARTCOLS_DEBUG=all
enables libsmartcols debug output.
SEE ALSO
fdisk(8), cfdisk(8), parted(8), partprobe(8), partx(8)
AUTHOR
Karel Zak <kzak@redhat.com>
The current sfdisk implementation is based on the original sfdisk from Andries E. Brouwer.
AVAILABILITY
The sfdisk command is part of the util-linux package and is available from
ftp://ftp.kernel.org/pub/linux/utils/util-linux/.