Provided by: sg3-utils_1.40-0ubuntu1_amd64 
NAME
sg_write_same - send SCSI WRITE SAME command
SYNOPSIS
sg_write_same [--10] [--16] [--32] [--anchor] [--grpnum=GN] [--help] [--in=IF] [--lba=LBA]
[--lbdata] [--pbdata] [--num=NUM] [--ndob] [--timeout=TO] [--unmap] [--verbose]
[--version] [--wrprotect=WPR] [--xferlen=LEN] DEVICE
DESCRIPTION
Send the SCSI WRITE SAME (10, 16 or 32 byte) command to DEVICE. This command writes the
given block NUM times to consecutive blocks on the DEVICE starting at logical block
address LBA.
SBC-3 revision 35d introduced a "no data-out buffer" (NDOB) bit which, if set, bypasses
the requirement to send a single block of data to the DEVICE together with the command.
Only WRITE SAME (16 and 32 byte) support the NDOB bit.
The length of the block to be written multiple times is obtained from either the LEN
argument, or the length of the given input file IF, or by calling READ CAPACITY(16) on
DEVICE. The contents of the block to be written are obtained from the input file IF or
zeros are used. If READ CAPACITY(16) is called (which implies IF was not given) and the
PROT_EN bit is set then an extra 8 bytes (i.e. more than the logical block size) of 0xff
are sent. If READ CAPACITY(16) fails then READ CAPACITY(10) is used to determine the block
size.
If neither --10, --16 nor --32 is given then WRITE SAME(10) is sent unless one of the
following conditions is met. If LBA (plus NUM) exceeds 32 bits, NUM exceeds 65535, or the
--unmap option is given then WRITE SAME(16) is sent. The --10, --16 and --32 options are
mutually exclusive.
In SBC-3 revision 26 the UNMAP and ANCHOR bits were added to the WRITE SAME (10) command.
Since the UNMAP bit has been in WRITE SAME (16) and WRITE SAME (32) since SBC-3 revision
18, the lower of the two (i.e. WRITE SAME (16)) is the default when the --unmap option is
given. To send WRITE SAME (10) use the --10 option.
Take care: The WRITE SAME(10, 16 and 32) commands interpret a NUM of zero as write to the
end of DEVICE. This utility defaults NUM to 1 . The WRITE SAME commands have no IMMED bit
so if NUM is large (or zero) then an invocation of this utility could take a long time,
potentially as long as a FORMAT UNIT command. In such situations the command timeout value
TO may need to be increased from its default value of 60 seconds. In SBC-3 revision 26 the
WSNZ (write same no zero) bit was added to the Block Limits VPD page [0xB0]. If set the
WRITE SAME commands will not accept a NUM of zero. The same SBC-3 revision added the
"Maximum Write Same Length" field to the Block Limits VPD page.
The Logical Block Provisioning VPD page [0xB2] contains the LBWS and LBW10 bits. If LBWS
is set then WRITE SAME (16) supports the UNMAP bit. If LBWS10 is set then WRITE SAME (10)
supports the UNMAP bit. If either LBWS or LBWS10 is set and the WRITE SAME (32) is
supported then WRITE SAME (32) supports the UNMAP bit. This is as of SBC-3 revision 26.
As a precaution against an accidental 'sg_write_same /dev/sda' (for example) overwriting
LBA 0 on /dev/sda with zeros, at least one of the --in=IF, --lba=LBA or --num=NUM options
must be given. Obviously this utility can destroy a lot of user data so check the options
carefully.
OPTIONS
Arguments to long options are mandatory for short options as well.
-R, --10
send a SCSI WRITE SAME (10) command to DEVICE. The ability to set the --unmap (and
--anchor) options to this command was added in SBC-3 revision 26.
-S, --16
send a SCSI WRITE SAME (16) command to DEVICE.
-T, --32
send a SCSI WRITE SAME (32) command to DEVICE.
-a, --anchor
sets the ANCHOR bit in the cdb. Introduced in SBC-3 revision 22. That draft
requires the --unmap option to also be specified.
-g, --grpnum=GN
sets the 'Group number' field to GN. Defaults to a value of zero. GN should be a
value between 0 and 31.
-h, --help
output the usage message then exit.
-i, --in=IF
read data (binary) from file named IF and use it as the data out buffer for the
SCSI WRITE SAME command. The length of the data out buffer is --xferlen=LEN or, if
that is not given, the length of the IF file. If IF is "-" then stdin is read. If
this option is not given then 0x00 bytes are used as fill with the length of the
data out buffer obtained from --xferlen=LEN or by calling READ CAPACITY(16 or 10).
If the response to READ CAPACITY(16) has the PROT_EN bit set then data out buffer
size is modified accordingly with the last 8 bytes set to 0xff.
-l, --lba=LBA
where LBA is the logical block address to start the WRITE SAME command. Defaults
to lba 0 which is a dangerous block to overwrite on a disk that is in use. Assumed
to be in decimal unless prefixed with '0x' or has a trailing 'h'.
-L, --lbdata
sets the LBDATA bit in the WRITE SAME cdb.
-N, --ndob
sets the NDOB bit in the WRITE SAME (16 and 32 byte) commands. Default is to clear
this bit. When this option is given then --in=IF is not allowed and --xferlen=LEN
can only be given if LEN is 0 .
-n, --num=NUM
where NUM is the number of blocks, starting at LBA, to write the data out buffer
to. The default value for NUM is 1. The value corresponds to the 'Number of logical
blocks' field in the WRITE SAME cdb. Note that a value of 0 in NUM is interpreted
as write the data out buffer on every block starting at LBA to the end of the
DEVICE.
-P, --pbdata
sets the PBDATA bit in the WRITE SAME cdb.
-t, --timeout=TO
where TO is the command timeout value in seconds. The default value is 60 seconds.
If NUM is large (or zero) a WRITE SAME command may require considerably more time
than 60 seconds to complete.
-U, --unmap
sets the UNMAP bit in the WRITE SAME(10, 16 and 32) cdb. See UNMAP section below.
-v, --verbose
increase the degree of verbosity (debug messages).
-V, --version
output version string then exit.
-w, --wrprotect=WPR
sets the "Write protect" field in the WRITE SAME cdb to WPR. The default value is
zero. WPR should be a value between 0 and 7. When WPR is 1 or greater, and the
disk's protection type is 1 or greater, then 8 extra bytes of protection
information are expected or generated (to place in the command's data out buffer).
-x, --xferlen=LEN
where LEN is the data out buffer length. Defaults to the length of the IF file or,
if that is not given, then the READ CAPACITY(16 or 10) command is used to find the
'Logical block length in bytes'. That figure may be increased by 8 bytes if the
DEVICE's protection type is 1 or greater and the WRPROTECT field (see
--wrprotect=WPR) is 1 or greater. If both this option and the IF option are given
and LEN exceeds the length of the IF file then LEN is the data out buffer length
with zeros used as pad bytes.
UNMAP
Logical block provisioning is a new term introduced in SBC-3 revision 25 for the ability
to mark blocks as unused. For large storage arrays, it is a way to provision less physical
storage than the READ CAPACITY command reports is available, potentially allocating more
physical storage when WRITE commands require it. For flash memory (e.g. SSD drives) it is
a way of potentially saving power (and perhaps access time) when it is known large
sections (or almost all) of the flash memory is not in use. SSDs need wear levelling
algorithms to have acceptable endurance and typically over provision to simplify those
algorithms; hence they typically contain more physical flash storage than their logical
size would dictate.
Support for logical block provisioning is indicated by the LBPME bit being set in the READ
CAPACITY(16) command response (see the sg_readcap utility). That implies at least one of
the UNMAP or WRITE SAME(16) commands is implemented. If the UNMAP command is implemented
then the "Maximum unmap LBA count" and "Maximum unmap block descriptor count" fields in
the Block Limits VPD page should both be greater than zero. The READ CAPACITY(16) command
response also contains a LBPRZ bit which if set means that if unmapped blocks are read
then zeros will be returned for the data (and if protection information is active, 0xff
bytes are returned for that). In SBC-3 revision 27 the same LBPRZ bit was added to the
Logical Block Provisioning VPD page.
In SBC-3 revision 25 the LBPU and ANC_SUP bits where added to the Logical Block
Provisioning VPD page. When LBPU is set it indicates that the device supports the UNMAP
command (see the sg_unmap utility). When the ANC_SUP bit is set it indicates the device
supports anchored LBAs.
When the UNMAP bit is set in the cdb then the data out buffer is also sent. Additionally
the data section of that data out buffer should be full of 0x0 bytes while the data
protection block, 8 bytes at the end if present, should be set to 0xff bytes. If these
conditions are not met and the LBPRZ bit is set then the UNMAP bit is ignored and the data
out buffer is written to the DEVICE as if the UNMAP bit was zero. In the absence of the
--in=IF option, this utility will attempt build a data out buffer that meets the
requirements for the UNMAP bit in the cdb to be acted on by the DEVICE.
Logical blocks may also be unmapped by the SCSI UNMAP and FORMAT UNIT commands (see the
sg_unmap and sg_format utilities).
The unmap capability in SCSI is closely related to the ATA DATA SET MANAGEMENT command
with the "Trim" bit set. That ATA trim capability does not interact well with SATA command
queueing known as NCQ. T13 have introduced a new command called the SFQ DATA SET
MANAGEMENT command also with a the "Trim" bit to address that problem. The SCSI WRITE SAME
with the UNMAP bit set and the UNMAP commands do not have any problems with SCSI queueing.
NOTES
Various numeric arguments (e.g. LBA) may include multiplicative suffixes or be given in
hexadecimal. See the "NUMERIC ARGUMENTS" section in the sg3_utils(8) man page.
In Linux at this time the sg driver does not support cdb sizes greater than 16 bytes.
[This restriction will be removed in lk 3.17 .] Hence a device node like /dev/sg1 which is
associated with the sg driver will fail with this utility if the --32 option is given (or
implied by other options). The bsg driver with device nodes like /dev/bsg/6:0:0:1 does
support cdb sizes greater than 16 bytes.
EXIT STATUS
The exit status of sg_write_same is 0 when it is successful. Otherwise see the
sg3_utils(8) man page.
EXAMPLES
One simple usage is to write blocks of zero from (and including) a given LBA:
sg_write_same --lba=0x1234 --num=63 /dev/sdc
Since --xferlen=LEN has not been given, then this utility will call the READ CAPACITY
command on /dev/sdc to determine the number of bytes in a logical block. Let us assume
that is 512 bytes. Since --in=IF is not given a block of zeros is assumed. So 63 blocks of
zeros (each block containing 512 bytes) will be written from (and including) LBA 0x1234 .
Note that only one block of zeros is passed to the SCSI WRITE SAME command in the data out
buffer (as required by SBC-3).
A similar example follows but in this case the blocks are "unmapped" ("trimmed" in ATA
speak) rather than zeroed:
sg_write_same --unmap -L 0x1234 -n 63 /dev/sdc
Note that if the LBPRZ bit in the READ CAPACITY(16) response is set (i.e. LPPRZ is an
acronym for logical block provisioning read zeros) then these two examples do the same
thing, at least seen from the point of view of subsequent reads.
This utility can also be used to write protection information (PI) on disks formatted with
a protection type greater than zero. PI is 8 bytes of extra data appended to the user data
of a logical block: the first two bytes are a CRC (the "guard"), the next two bytes are
the "application tag" and the last four bytes are the "reference tag". With protection
types 1 and 2 if the application tag is 0xffff then the guard should not be checked
(against the user data).
In this example we assume the logical block size (of the user data) is 512 bytes and the
disk has been formatted with protection type 1. Since we are going to modify LBA 2468 then
we take a copy of it first:
dd if=/dev/sdb skip=2468 bs=512 of=2468.bin count=1
The following command line sets the user data to zeros and the PI to 8 0xFF bytes on LBA
2468:
sg_write_same --lba=2468 /dev/sdb
Reading back that block should be successful because the application tag is 0xffff which
suppresses the guard (CRC) check (which would otherwise be wrong):
dd if=/dev/sdb skip=2468 bs=512 of=/dev/null count=1
Now an attempt is made to create a binary file with zeros in the user data, 0x0000 in the
application tag and 0xff bytes in the other two PI fields. It is awkward to create 0xff
bytes in a file (in Unix) as the "tr" command below shows:
dd if=/dev/zero bs=1 count=512 of=ud.bin
tr "\000" "\377" < /dev/zero | dd bs=1 of=ff_s.bin count=8
cat ud.bin ff_s.bin > lb.bin
dd if=/dev/zero bs=1 count=2 seek=514 conv=notrunc of=lb.bin
The resulting file can be viewed with 'hexdump -C lb.bin' and should contain 520 bytes.
Now that file can be written to LBA 2468 as follows:
sg_write_same --lba=2468 wrprotect=3 --in=lb.bin /dev/sdb
Note the --wrprotect=3 rather than being set to 1, since we want the WRITE SAME command to
succeed even though the PI data now indicates the user data is corrupted. When an attempt
is made to read the LBA, an error should occur:
dd if=/dev/sdb skip=2468 bs=512 of=/dev/null count=1
dd errors are not very expressive, if dmesg is checked there should be a line something
like this: "[sdb] Add. Sense: Logical block guard check failed". The block can be
corrected by doing a "sg_write_same --lba=1234 /dev/sdb" again or restoring the original
contents of that LBA:
dd if=2468.bin bs=512 seek=2468 of=/dev/sdb conv=notrunc count=1
Hopefully the dd command would never try to truncate the output file when it is a block
device.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2009-2014 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_format,sg_get_lba_status,sg_readcap,sg_vpd,sg_unmap(sg3_utils)