Provided by: binutils-arm-none-eabi_2.26-4ubuntu1+8_amd64 
NAME
AS - the portable GNU assembler.
SYNOPSIS
as [-a[cdghlns][=file]] [--alternate] [-D]
[--compress-debug-sections] [--nocompress-debug-sections]
[--debug-prefix-map old=new]
[--defsym sym=val] [-f] [-g] [--gstabs]
[--gstabs+] [--gdwarf-2] [--gdwarf-sections]
[--help] [-I dir] [-J]
[-K] [-L] [--listing-lhs-width=NUM]
[--listing-lhs-width2=NUM] [--listing-rhs-width=NUM]
[--listing-cont-lines=NUM] [--keep-locals]
[-o objfile] [-R]
[--hash-size=NUM] [--reduce-memory-overheads]
[--statistics]
[-v] [-version] [--version]
[-W] [--warn] [--fatal-warnings] [-w] [-x]
[-Z] [@FILE]
[--sectname-subst] [--size-check=[error|warning]]
[--target-help] [target-options]
[--|files ...]
Target AArch64 options:
[-EB|-EL]
[-mabi=ABI]
Target Alpha options:
[-mcpu]
[-mdebug | -no-mdebug]
[-replace | -noreplace]
[-relax] [-g] [-Gsize]
[-F] [-32addr]
Target ARC options:
[-mcpu=cpu]
[-mA6|-mARC600|-mARC601|-mA7|-mARC700|-mEM|-mHS]
[-mcode-density]
[-EB|-EL]
Target ARM options:
[-mcpu=processor[+extension...]]
[-march=architecture[+extension...]]
[-mfpu=floating-point-format]
[-mfloat-abi=abi]
[-meabi=ver]
[-mthumb]
[-EB|-EL]
[-mapcs-32|-mapcs-26|-mapcs-float|
-mapcs-reentrant]
[-mthumb-interwork] [-k]
Target Blackfin options:
[-mcpu=processor[-sirevision]]
[-mfdpic]
[-mno-fdpic]
[-mnopic]
Target CRIS options:
[--underscore | --no-underscore]
[--pic] [-N]
[--emulation=criself | --emulation=crisaout]
[--march=v0_v10 | --march=v10 | --march=v32 | --march=common_v10_v32]
Target D10V options:
[-O]
Target D30V options:
[-O|-n|-N]
Target EPIPHANY options:
[-mepiphany|-mepiphany16]
Target H8/300 options:
[-h-tick-hex]
Target i386 options:
[--32|--x32|--64] [-n]
[-march=CPU[+EXTENSION...]] [-mtune=CPU]
Target i960 options:
[-ACA|-ACA_A|-ACB|-ACC|-AKA|-AKB|
-AKC|-AMC]
[-b] [-no-relax]
Target IA-64 options:
[-mconstant-gp|-mauto-pic]
[-milp32|-milp64|-mlp64|-mp64]
[-mle|mbe]
[-mtune=itanium1|-mtune=itanium2]
[-munwind-check=warning|-munwind-check=error]
[-mhint.b=ok|-mhint.b=warning|-mhint.b=error]
[-x|-xexplicit] [-xauto] [-xdebug]
Target IP2K options:
[-mip2022|-mip2022ext]
Target M32C options:
[-m32c|-m16c] [-relax] [-h-tick-hex]
Target M32R options:
[--m32rx|--[no-]warn-explicit-parallel-conflicts|
--W[n]p]
Target M680X0 options:
[-l] [-m68000|-m68010|-m68020|...]
Target M68HC11 options:
[-m68hc11|-m68hc12|-m68hcs12|-mm9s12x|-mm9s12xg]
[-mshort|-mlong]
[-mshort-double|-mlong-double]
[--force-long-branches] [--short-branches]
[--strict-direct-mode] [--print-insn-syntax]
[--print-opcodes] [--generate-example]
Target MCORE options:
[-jsri2bsr] [-sifilter] [-relax]
[-mcpu=[210|340]]
Target Meta options:
[-mcpu=cpu] [-mfpu=cpu] [-mdsp=cpu] Target MICROBLAZE options:
Target MIPS options:
[-nocpp] [-EL] [-EB] [-O[optimization level]]
[-g[debug level]] [-G num] [-KPIC] [-call_shared]
[-non_shared] [-xgot [-mvxworks-pic]
[-mabi=ABI] [-32] [-n32] [-64] [-mfp32] [-mgp32]
[-mfp64] [-mgp64] [-mfpxx]
[-modd-spreg] [-mno-odd-spreg]
[-march=CPU] [-mtune=CPU] [-mips1] [-mips2]
[-mips3] [-mips4] [-mips5] [-mips32] [-mips32r2]
[-mips32r3] [-mips32r5] [-mips32r6] [-mips64] [-mips64r2]
[-mips64r3] [-mips64r5] [-mips64r6]
[-construct-floats] [-no-construct-floats]
[-mnan=encoding]
[-trap] [-no-break] [-break] [-no-trap]
[-mips16] [-no-mips16]
[-mmicromips] [-mno-micromips]
[-msmartmips] [-mno-smartmips]
[-mips3d] [-no-mips3d]
[-mdmx] [-no-mdmx]
[-mdsp] [-mno-dsp]
[-mdspr2] [-mno-dspr2]
[-mmsa] [-mno-msa]
[-mxpa] [-mno-xpa]
[-mmt] [-mno-mt]
[-mmcu] [-mno-mcu]
[-minsn32] [-mno-insn32]
[-mfix7000] [-mno-fix7000]
[-mfix-rm7000] [-mno-fix-rm7000]
[-mfix-vr4120] [-mno-fix-vr4120]
[-mfix-vr4130] [-mno-fix-vr4130]
[-mdebug] [-no-mdebug]
[-mpdr] [-mno-pdr]
Target MMIX options:
[--fixed-special-register-names] [--globalize-symbols]
[--gnu-syntax] [--relax] [--no-predefined-symbols]
[--no-expand] [--no-merge-gregs] [-x]
[--linker-allocated-gregs]
Target Nios II options:
[-relax-all] [-relax-section] [-no-relax]
[-EB] [-EL]
Target NDS32 options:
[-EL] [-EB] [-O] [-Os] [-mcpu=cpu]
[-misa=isa] [-mabi=abi] [-mall-ext]
[-m[no-]16-bit] [-m[no-]perf-ext] [-m[no-]perf2-ext]
[-m[no-]string-ext] [-m[no-]dsp-ext] [-m[no-]mac] [-m[no-]div]
[-m[no-]audio-isa-ext] [-m[no-]fpu-sp-ext] [-m[no-]fpu-dp-ext]
[-m[no-]fpu-fma] [-mfpu-freg=FREG] [-mreduced-regs]
[-mfull-regs] [-m[no-]dx-regs] [-mpic] [-mno-relax]
[-mb2bb]
Target PDP11 options:
[-mpic|-mno-pic] [-mall] [-mno-extensions]
[-mextension|-mno-extension]
[-mcpu] [-mmachine]
Target picoJava options:
[-mb|-me]
Target PowerPC options:
[-a32|-a64]
[-mpwrx|-mpwr2|-mpwr|-m601|-mppc|-mppc32|-m603|-m604|-m403|-m405|
-m440|-m464|-m476|-m7400|-m7410|-m7450|-m7455|-m750cl|-mppc64|
-m620|-me500|-e500x2|-me500mc|-me500mc64|-me5500|-me6500|-mppc64bridge|
-mbooke|-mpower4|-mpwr4|-mpower5|-mpwr5|-mpwr5x|-mpower6|-mpwr6|
-mpower7|-mpwr7|-mpower8|-mpwr8|-mpower9|-mpwr9-ma2|
-mcell|-mspe|-mtitan|-me300|-mcom]
[-many] [-maltivec|-mvsx|-mhtm|-mvle]
[-mregnames|-mno-regnames]
[-mrelocatable|-mrelocatable-lib|-K PIC] [-memb]
[-mlittle|-mlittle-endian|-le|-mbig|-mbig-endian|-be]
[-msolaris|-mno-solaris]
[-nops=count]
Target RL78 options:
[-mg10]
[-m32bit-doubles|-m64bit-doubles]
Target RX options:
[-mlittle-endian|-mbig-endian]
[-m32bit-doubles|-m64bit-doubles]
[-muse-conventional-section-names]
[-msmall-data-limit]
[-mpid]
[-mrelax]
[-mint-register=number]
[-mgcc-abi|-mrx-abi]
Target s390 options:
[-m31|-m64] [-mesa|-mzarch] [-march=CPU]
[-mregnames|-mno-regnames]
[-mwarn-areg-zero]
Target SCORE options:
[-EB][-EL][-FIXDD][-NWARN]
[-SCORE5][-SCORE5U][-SCORE7][-SCORE3]
[-march=score7][-march=score3]
[-USE_R1][-KPIC][-O0][-G num][-V]
Target SPARC options:
[-Av6|-Av7|-Av8|-Asparclet|-Asparclite
-Av8plus|-Av8plusa|-Av9|-Av9a]
[-xarch=v8plus|-xarch=v8plusa] [-bump]
[-32|-64]
Target TIC54X options:
[-mcpu=54[123589]|-mcpu=54[56]lp] [-mfar-mode|-mf]
[-merrors-to-file <filename>|-me <filename>]
Target TIC6X options:
[-march=arch] [-mbig-endian|-mlittle-endian]
[-mdsbt|-mno-dsbt] [-mpid=no|-mpid=near|-mpid=far]
[-mpic|-mno-pic]
Target TILE-Gx options:
[-m32|-m64][-EB][-EL]
Target Visium options:
[-mtune=arch]
Target Xtensa options:
[--[no-]text-section-literals] [--[no-]auto-litpools]
[--[no-]absolute-literals]
[--[no-]target-align] [--[no-]longcalls]
[--[no-]transform]
[--rename-section oldname=newname]
[--[no-]trampolines]
Target Z80 options:
[-z80] [-r800]
[ -ignore-undocumented-instructions] [-Wnud]
[ -ignore-unportable-instructions] [-Wnup]
[ -warn-undocumented-instructions] [-Wud]
[ -warn-unportable-instructions] [-Wup]
[ -forbid-undocumented-instructions] [-Fud]
[ -forbid-unportable-instructions] [-Fup]
DESCRIPTION
GNU as is really a family of assemblers. If you use (or have used) the GNU assembler on one
architecture, you should find a fairly similar environment when you use it on another architecture. Each
version has much in common with the others, including object file formats, most assembler directives
(often called pseudo-ops) and assembler syntax.
as is primarily intended to assemble the output of the GNU C compiler "gcc" for use by the linker "ld".
Nevertheless, we've tried to make as assemble correctly everything that other assemblers for the same
machine would assemble. Any exceptions are documented explicitly. This doesn't mean as always uses the
same syntax as another assembler for the same architecture; for example, we know of several incompatible
versions of 680x0 assembly language syntax.
Each time you run as it assembles exactly one source program. The source program is made up of one or
more files. (The standard input is also a file.)
You give as a command line that has zero or more input file names. The input files are read (from left
file name to right). A command line argument (in any position) that has no special meaning is taken to
be an input file name.
If you give as no file names it attempts to read one input file from the as standard input, which is
normally your terminal. You may have to type ctl-D to tell as there is no more program to assemble.
Use -- if you need to explicitly name the standard input file in your command line.
If the source is empty, as produces a small, empty object file.
as may write warnings and error messages to the standard error file (usually your terminal). This should
not happen when a compiler runs as automatically. Warnings report an assumption made so that as could
keep assembling a flawed program; errors report a grave problem that stops the assembly.
If you are invoking as via the GNU C compiler, you can use the -Wa option to pass arguments through to
the assembler. The assembler arguments must be separated from each other (and the -Wa) by commas. For
example:
gcc -c -g -O -Wa,-alh,-L file.c
This passes two options to the assembler: -alh (emit a listing to standard output with high-level and
assembly source) and -L (retain local symbols in the symbol table).
Usually you do not need to use this -Wa mechanism, since many compiler command-line options are
automatically passed to the assembler by the compiler. (You can call the GNU compiler driver with the -v
option to see precisely what options it passes to each compilation pass, including the assembler.)
OPTIONS
@file
Read command-line options from file. The options read are inserted in place of the original @file
option. If file does not exist, or cannot be read, then the option will be treated literally, and
not removed.
Options in file are separated by whitespace. A whitespace character may be included in an option by
surrounding the entire option in either single or double quotes. Any character (including a
backslash) may be included by prefixing the character to be included with a backslash. The file may
itself contain additional @file options; any such options will be processed recursively.
-a[cdghlmns]
Turn on listings, in any of a variety of ways:
-ac omit false conditionals
-ad omit debugging directives
-ag include general information, like as version and options passed
-ah include high-level source
-al include assembly
-am include macro expansions
-an omit forms processing
-as include symbols
=file
set the name of the listing file
You may combine these options; for example, use -aln for assembly listing without forms processing.
The =file option, if used, must be the last one. By itself, -a defaults to -ahls.
--alternate
Begin in alternate macro mode.
--compress-debug-sections
Compress DWARF debug sections using zlib with SHF_COMPRESSED from the ELF ABI. The resulting object
file may not be compatible with older linkers and object file utilities. Note if compression would
make a given section larger then it is not compressed.
--compress-debug-sections=none
--compress-debug-sections=zlib
--compress-debug-sections=zlib-gnu
--compress-debug-sections=zlib-gabi
These options control how DWARF debug sections are compressed. --compress-debug-sections=none is
equivalent to --nocompress-debug-sections. --compress-debug-sections=zlib and
--compress-debug-sections=zlib-gabi are equivalent to --compress-debug-sections.
--compress-debug-sections=zlib-gnu compresses DWARF debug sections using zlib. The debug sections
are renamed to begin with .zdebug. Note if compression would make a given section larger then it is
not compressed nor renamed.
--nocompress-debug-sections
Do not compress DWARF debug sections. This is usually the default for all targets except the
x86/x86_64, but a configure time option can be used to override this.
-D Ignored. This option is accepted for script compatibility with calls to other assemblers.
--debug-prefix-map old=new
When assembling files in directory old, record debugging information describing them as in new
instead.
--defsym sym=value
Define the symbol sym to be value before assembling the input file. value must be an integer
constant. As in C, a leading 0x indicates a hexadecimal value, and a leading 0 indicates an octal
value. The value of the symbol can be overridden inside a source file via the use of a ".set"
pseudo-op.
-f "fast"---skip whitespace and comment preprocessing (assume source is compiler output).
-g
--gen-debug
Generate debugging information for each assembler source line using whichever debug format is
preferred by the target. This currently means either STABS, ECOFF or DWARF2.
--gstabs
Generate stabs debugging information for each assembler line. This may help debugging assembler
code, if the debugger can handle it.
--gstabs+
Generate stabs debugging information for each assembler line, with GNU extensions that probably only
gdb can handle, and that could make other debuggers crash or refuse to read your program. This may
help debugging assembler code. Currently the only GNU extension is the location of the current
working directory at assembling time.
--gdwarf-2
Generate DWARF2 debugging information for each assembler line. This may help debugging assembler
code, if the debugger can handle it. Note---this option is only supported by some targets, not all
of them.
--gdwarf-sections
Instead of creating a .debug_line section, create a series of .debug_line.foo sections where foo is
the name of the corresponding code section. For example a code section called .text.func will have
its dwarf line number information placed into a section called .debug_line.text.func. If the code
section is just called .text then debug line section will still be called just .debug_line without
any suffix.
--size-check=error
--size-check=warning
Issue an error or warning for invalid ELF .size directive.
--help
Print a summary of the command line options and exit.
--target-help
Print a summary of all target specific options and exit.
-I dir
Add directory dir to the search list for ".include" directives.
-J Don't warn about signed overflow.
-K Issue warnings when difference tables altered for long displacements.
-L
--keep-locals
Keep (in the symbol table) local symbols. These symbols start with system-specific local label
prefixes, typically .L for ELF systems or L for traditional a.out systems.
--listing-lhs-width=number
Set the maximum width, in words, of the output data column for an assembler listing to number.
--listing-lhs-width2=number
Set the maximum width, in words, of the output data column for continuation lines in an assembler
listing to number.
--listing-rhs-width=number
Set the maximum width of an input source line, as displayed in a listing, to number bytes.
--listing-cont-lines=number
Set the maximum number of lines printed in a listing for a single line of input to number + 1.
-o objfile
Name the object-file output from as objfile.
-R Fold the data section into the text section.
--hash-size=number
Set the default size of GAS's hash tables to a prime number close to number. Increasing this value
can reduce the length of time it takes the assembler to perform its tasks, at the expense of
increasing the assembler's memory requirements. Similarly reducing this value can reduce the memory
requirements at the expense of speed.
--reduce-memory-overheads
This option reduces GAS's memory requirements, at the expense of making the assembly processes
slower. Currently this switch is a synonym for --hash-size=4051, but in the future it may have other
effects as well.
--sectname-subst
Honor substitution sequences in section names.
--statistics
Print the maximum space (in bytes) and total time (in seconds) used by assembly.
--strip-local-absolute
Remove local absolute symbols from the outgoing symbol table.
-v
-version
Print the as version.
--version
Print the as version and exit.
-W
--no-warn
Suppress warning messages.
--fatal-warnings
Treat warnings as errors.
--warn
Don't suppress warning messages or treat them as errors.
-w Ignored.
-x Ignored.
-Z Generate an object file even after errors.
-- | files ...
Standard input, or source files to assemble.
The following options are available when as is configured for the 64-bit mode of the ARM Architecture
(AArch64).
-EB This option specifies that the output generated by the assembler should be marked as being encoded
for a big-endian processor.
-EL This option specifies that the output generated by the assembler should be marked as being encoded
for a little-endian processor.
-mabi=abi
Specify which ABI the source code uses. The recognized arguments are: "ilp32" and "lp64", which
decides the generated object file in ELF32 and ELF64 format respectively. The default is "lp64".
-mcpu=processor[+extension...]
This option specifies the target processor. The assembler will issue an error message if an attempt
is made to assemble an instruction which will not execute on the target processor. The following
processor names are recognized: "cortex-a35", "cortex-a53", "cortex-a57", "cortex-a72", "exynos-m1",
"qdf24xx", "thunderx", "xgene1" and "xgene2". The special name "all" may be used to allow the
assembler to accept instructions valid for any supported processor, including all optional
extensions.
In addition to the basic instruction set, the assembler can be told to accept, or restrict, various
extension mnemonics that extend the processor.
If some implementations of a particular processor can have an extension, then then those extensions
are automatically enabled. Consequently, you will not normally have to specify any additional
extensions.
-march=architecture[+extension...]
This option specifies the target architecture. The assembler will issue an error message if an
attempt is made to assemble an instruction which will not execute on the target architecture. The
following architecture names are recognized: "armv8-a", "armv8.1-a" and "armv8.2-a".
If both -mcpu and -march are specified, the assembler will use the setting for -mcpu. If neither are
specified, the assembler will default to -mcpu=all.
The architecture option can be extended with the same instruction set extension options as the -mcpu
option. Unlike -mcpu, extensions are not always enabled by default,
-mverbose-error
This option enables verbose error messages for AArch64 gas. This option is enabled by default.
-mno-verbose-error
This option disables verbose error messages in AArch64 gas.
The following options are available when as is configured for an Alpha processor.
-mcpu
This option specifies the target processor. If an attempt is made to assemble an instruction which
will not execute on the target processor, the assembler may either expand the instruction as a macro
or issue an error message. This option is equivalent to the ".arch" directive.
The following processor names are recognized: 21064, "21064a", 21066, 21068, 21164, "21164a",
"21164pc", 21264, "21264a", "21264b", "ev4", "ev5", "lca45", "ev5", "ev56", "pca56", "ev6", "ev67",
"ev68". The special name "all" may be used to allow the assembler to accept instructions valid for
any Alpha processor.
In order to support existing practice in OSF/1 with respect to ".arch", and existing practice within
MILO (the Linux ARC bootloader), the numbered processor names (e.g. 21064) enable the processor-
specific PALcode instructions, while the "electro-vlasic" names (e.g. "ev4") do not.
-mdebug
-no-mdebug
Enables or disables the generation of ".mdebug" encapsulation for stabs directives and procedure
descriptors. The default is to automatically enable ".mdebug" when the first stabs directive is
seen.
-relax
This option forces all relocations to be put into the object file, instead of saving space and
resolving some relocations at assembly time. Note that this option does not propagate all symbol
arithmetic into the object file, because not all symbol arithmetic can be represented. However, the
option can still be useful in specific applications.
-replace
-noreplace
Enables or disables the optimization of procedure calls, both at assemblage and at link time. These
options are only available for VMS targets and "-replace" is the default. See section 1.4.1 of the
OpenVMS Linker Utility Manual.
-g This option is used when the compiler generates debug information. When gcc is using mips-tfile to
generate debug information for ECOFF, local labels must be passed through to the object file.
Otherwise this option has no effect.
-Gsize
A local common symbol larger than size is placed in ".bss", while smaller symbols are placed in
".sbss".
-F
-32addr
These options are ignored for backward compatibility.
The following options are available when as is configured for an ARC processor.
-mcpu=cpu
This option selects the core processor variant.
-EB | -EL
Select either big-endian (-EB) or little-endian (-EL) output.
-mcode-density
Enable Code Density extenssion instructions.
The following options are available when as is configured for the ARM processor family.
-mcpu=processor[+extension...]
Specify which ARM processor variant is the target.
-march=architecture[+extension...]
Specify which ARM architecture variant is used by the target.
-mfpu=floating-point-format
Select which Floating Point architecture is the target.
-mfloat-abi=abi
Select which floating point ABI is in use.
-mthumb
Enable Thumb only instruction decoding.
-mapcs-32 | -mapcs-26 | -mapcs-float | -mapcs-reentrant
Select which procedure calling convention is in use.
-EB | -EL
Select either big-endian (-EB) or little-endian (-EL) output.
-mthumb-interwork
Specify that the code has been generated with interworking between Thumb and ARM code in mind.
-mccs
Turns on CodeComposer Studio assembly syntax compatibility mode.
-k Specify that PIC code has been generated.
The following options are available when as is configured for the Blackfin processor family.
-mcpu=processor[-sirevision]
This option specifies the target processor. The optional sirevision is not used in assembler. It's
here such that GCC can easily pass down its "-mcpu=" option. The assembler will issue an error
message if an attempt is made to assemble an instruction which will not execute on the target
processor. The following processor names are recognized: "bf504", "bf506", "bf512", "bf514",
"bf516", "bf518", "bf522", "bf523", "bf524", "bf525", "bf526", "bf527", "bf531", "bf532", "bf533",
"bf534", "bf535" (not implemented yet), "bf536", "bf537", "bf538", "bf539", "bf542", "bf542m",
"bf544", "bf544m", "bf547", "bf547m", "bf548", "bf548m", "bf549", "bf549m", "bf561", and "bf592".
-mfdpic
Assemble for the FDPIC ABI.
-mno-fdpic
-mnopic
Disable -mfdpic.
See the info pages for documentation of the CRIS-specific options.
The following options are available when as is configured for a D10V processor.
-O Optimize output by parallelizing instructions.
The following options are available when as is configured for a D30V processor.
-O Optimize output by parallelizing instructions.
-n Warn when nops are generated.
-N Warn when a nop after a 32-bit multiply instruction is generated.
The following options are available when as is configured for an Epiphany processor.
-mepiphany
Specifies that the both 32 and 16 bit instructions are allowed. This is the default behavior.
-mepiphany16
Restricts the permitted instructions to just the 16 bit set.
The following options are available when as is configured for an H8/300 processor. @chapter H8/300
Dependent Features
Options
The Renesas H8/300 version of "as" has one machine-dependent option:
-h-tick-hex
Support H'00 style hex constants in addition to 0x00 style.
-mach=name
Sets the H8300 machine variant. The following machine names are recognised: "h8300h", "h8300hn",
"h8300s", "h8300sn", "h8300sx" and "h8300sxn".
The following options are available when as is configured for an i386 processor.
--32 | --x32 | --64
Select the word size, either 32 bits or 64 bits. --32 implies Intel i386 architecture, while --x32
and --64 imply AMD x86-64 architecture with 32-bit or 64-bit word-size respectively.
These options are only available with the ELF object file format, and require that the necessary BFD
support has been included (on a 32-bit platform you have to add --enable-64-bit-bfd to configure
enable 64-bit usage and use x86-64 as target platform).
-n By default, x86 GAS replaces multiple nop instructions used for alignment within code sections with
multi-byte nop instructions such as leal 0(%esi,1),%esi. This switch disables the optimization.
--divide
On SVR4-derived platforms, the character / is treated as a comment character, which means that it
cannot be used in expressions. The --divide option turns / into a normal character. This does not
disable / at the beginning of a line starting a comment, or affect using # for starting a comment.
-march=CPU[+EXTENSION...]
This option specifies the target processor. The assembler will issue an error message if an attempt
is made to assemble an instruction which will not execute on the target processor. The following
processor names are recognized: "i8086", "i186", "i286", "i386", "i486", "i586", "i686", "pentium",
"pentiumpro", "pentiumii", "pentiumiii", "pentium4", "prescott", "nocona", "core", "core2", "corei7",
"l1om", "k1om", "iamcu", "k6", "k6_2", "athlon", "opteron", "k8", "amdfam10", "bdver1", "bdver2",
"bdver3", "bdver4", "znver1", "btver1", "btver2", "generic32" and "generic64".
In addition to the basic instruction set, the assembler can be told to accept various extension
mnemonics. For example, "-march=i686+sse4+vmx" extends i686 with sse4 and vmx. The following
extensions are currently supported: 8087, 287, 387, "no87", "mmx", "nommx", "sse", "sse2", "sse3",
"ssse3", "sse4.1", "sse4.2", "sse4", "nosse", "avx", "avx2", "adx", "rdseed", "prfchw", "smap",
"mpx", "sha", "prefetchwt1", "clflushopt", "se1", "clwb", "pcommit", "avx512f", "avx512cd",
"avx512er", "avx512pf", "avx512vl", "avx512bw", "avx512dq", "avx512ifma", "avx512vbmi", "noavx",
"vmx", "vmfunc", "smx", "xsave", "xsaveopt", "xsavec", "xsaves", "aes", "pclmul", "fsgsbase",
"rdrnd", "f16c", "bmi2", "fma", "movbe", "ept", "lzcnt", "hle", "rtm", "invpcid", "clflush",
"mwaitx", "clzero", "lwp", "fma4", "xop", "cx16", "syscall", "rdtscp", "3dnow", "3dnowa", "sse4a",
"sse5", "svme", "abm" and "padlock". Note that rather than extending a basic instruction set, the
extension mnemonics starting with "no" revoke the respective functionality.
When the ".arch" directive is used with -march, the ".arch" directive will take precedent.
-mtune=CPU
This option specifies a processor to optimize for. When used in conjunction with the -march option,
only instructions of the processor specified by the -march option will be generated.
Valid CPU values are identical to the processor list of -march=CPU.
-msse2avx
This option specifies that the assembler should encode SSE instructions with VEX prefix.
-msse-check=none
-msse-check=warning
-msse-check=error
These options control if the assembler should check SSE instructions. -msse-check=none will make the
assembler not to check SSE instructions, which is the default. -msse-check=warning will make the
assembler issue a warning for any SSE instruction. -msse-check=error will make the assembler issue
an error for any SSE instruction.
-mavxscalar=128
-mavxscalar=256
These options control how the assembler should encode scalar AVX instructions. -mavxscalar=128 will
encode scalar AVX instructions with 128bit vector length, which is the default. -mavxscalar=256 will
encode scalar AVX instructions with 256bit vector length.
-mevexlig=128
-mevexlig=256
-mevexlig=512
These options control how the assembler should encode length-ignored (LIG) EVEX instructions.
-mevexlig=128 will encode LIG EVEX instructions with 128bit vector length, which is the default.
-mevexlig=256 and -mevexlig=512 will encode LIG EVEX instructions with 256bit and 512bit vector
length, respectively.
-mevexwig=0
-mevexwig=1
These options control how the assembler should encode w-ignored (WIG) EVEX instructions. -mevexwig=0
will encode WIG EVEX instructions with evex.w = 0, which is the default. -mevexwig=1 will encode WIG
EVEX instructions with evex.w = 1.
-mmnemonic=att
-mmnemonic=intel
This option specifies instruction mnemonic for matching instructions. The ".att_mnemonic" and
".intel_mnemonic" directives will take precedent.
-msyntax=att
-msyntax=intel
This option specifies instruction syntax when processing instructions. The ".att_syntax" and
".intel_syntax" directives will take precedent.
-mnaked-reg
This opetion specifies that registers don't require a % prefix. The ".att_syntax" and
".intel_syntax" directives will take precedent.
-madd-bnd-prefix
This option forces the assembler to add BND prefix to all branches, even if such prefix was not
explicitly specified in the source code.
-mno-shared
On ELF target, the assembler normally optimizes out non-PLT relocations against defined non-weak
global branch targets with default visibility. The -mshared option tells the assembler to generate
code which may go into a shared library where all non-weak global branch targets with default
visibility can be preempted. The resulting code is slightly bigger. This option only affects the
handling of branch instructions.
-mbig-obj
On x86-64 PE/COFF target this option forces the use of big object file format, which allows more than
32768 sections.
-momit-lock-prefix=no
-momit-lock-prefix=yes
These options control how the assembler should encode lock prefix. This option is intended as a
workaround for processors, that fail on lock prefix. This option can only be safely used with single-
core, single-thread computers -momit-lock-prefix=yes will omit all lock prefixes.
-momit-lock-prefix=no will encode lock prefix as usual, which is the default.
-mrelax-relocations=no
-mrelax-relocations=yes
These options control whether the assembler should generate relax relocations, R_386_GOT32X, in
32-bit mode, or R_X86_64_GOTPCRELX and R_X86_64_REX_GOTPCRELX, in 64-bit mode.
-mrelax-relocations=yes will generate relax relocations. -mrelax-relocations=no will not generate
relax relocations. The default can be controlled by a configure option
--enable-x86-relax-relocations.
-mevexrcig=rne
-mevexrcig=rd
-mevexrcig=ru
-mevexrcig=rz
These options control how the assembler should encode SAE-only EVEX instructions. -mevexrcig=rne
will encode RC bits of EVEX instruction with 00, which is the default. -mevexrcig=rd, -mevexrcig=ru
and -mevexrcig=rz will encode SAE-only EVEX instructions with 01, 10 and 11 RC bits, respectively.
-mamd64
-mintel64
This option specifies that the assembler should accept only AMD64 or Intel64 ISA in 64-bit mode. The
default is to accept both.
The following options are available when as is configured for the Intel 80960 processor.
-ACA | -ACA_A | -ACB | -ACC | -AKA | -AKB | -AKC | -AMC
Specify which variant of the 960 architecture is the target.
-b Add code to collect statistics about branches taken.
-no-relax
Do not alter compare-and-branch instructions for long displacements; error if necessary.
The following options are available when as is configured for the Ubicom IP2K series.
-mip2022ext
Specifies that the extended IP2022 instructions are allowed.
-mip2022
Restores the default behaviour, which restricts the permitted instructions to just the basic IP2022
ones.
The following options are available when as is configured for the Renesas M32C and M16C processors.
-m32c
Assemble M32C instructions.
-m16c
Assemble M16C instructions (the default).
-relax
Enable support for link-time relaxations.
-h-tick-hex
Support H'00 style hex constants in addition to 0x00 style.
The following options are available when as is configured for the Renesas M32R (formerly Mitsubishi M32R)
series.
--m32rx
Specify which processor in the M32R family is the target. The default is normally the M32R, but this
option changes it to the M32RX.
--warn-explicit-parallel-conflicts or --Wp
Produce warning messages when questionable parallel constructs are encountered.
--no-warn-explicit-parallel-conflicts or --Wnp
Do not produce warning messages when questionable parallel constructs are encountered.
The following options are available when as is configured for the Motorola 68000 series.
-l Shorten references to undefined symbols, to one word instead of two.
-m68000 | -m68008 | -m68010 | -m68020 | -m68030
| -m68040 | -m68060 | -m68302 | -m68331 | -m68332
| -m68333 | -m68340 | -mcpu32 | -m5200
Specify what processor in the 68000 family is the target. The default is normally the 68020, but
this can be changed at configuration time.
-m68881 | -m68882 | -mno-68881 | -mno-68882
The target machine does (or does not) have a floating-point coprocessor. The default is to assume a
coprocessor for 68020, 68030, and cpu32. Although the basic 68000 is not compatible with the 68881,
a combination of the two can be specified, since it's possible to do emulation of the coprocessor
instructions with the main processor.
-m68851 | -mno-68851
The target machine does (or does not) have a memory-management unit coprocessor. The default is to
assume an MMU for 68020 and up.
The following options are available when as is configured for an Altera Nios II processor.
-relax-section
Replace identified out-of-range branches with PC-relative "jmp" sequences when possible. The
generated code sequences are suitable for use in position-independent code, but there is a practical
limit on the extended branch range because of the length of the sequences. This option is the
default.
-relax-all
Replace branch instructions not determinable to be in range and all call instructions with "jmp" and
"callr" sequences (respectively). This option generates absolute relocations against the target
symbols and is not appropriate for position-independent code.
-no-relax
Do not replace any branches or calls.
-EB Generate big-endian output.
-EL Generate little-endian output. This is the default.
-march=architecture
This option specifies the target architecture. The assembler issues an error message if an attempt
is made to assemble an instruction which will not execute on the target architecture. The following
architecture names are recognized: "r1", "r2". The default is "r1".
The following options are available when as is configured for a Meta processor.
"-mcpu=metac11"
Generate code for Meta 1.1.
"-mcpu=metac12"
Generate code for Meta 1.2.
"-mcpu=metac21"
Generate code for Meta 2.1.
"-mfpu=metac21"
Allow code to use FPU hardware of Meta 2.1.
See the info pages for documentation of the MMIX-specific options.
The following options are available when as is configured for a NDS32 processor.
"-O1"
Optimize for performance.
"-Os"
Optimize for space.
"-EL"
Produce little endian data output.
"-EB"
Produce little endian data output.
"-mpic"
Generate PIC.
"-mno-fp-as-gp-relax"
Suppress fp-as-gp relaxation for this file.
"-mb2bb-relax"
Back-to-back branch optimization.
"-mno-all-relax"
Suppress all relaxation for this file.
"-march=<arch name>"
Assemble for architecture <arch name> which could be v3, v3j, v3m, v3f, v3s, v2, v2j, v2f, v2s.
"-mbaseline=<baseline>"
Assemble for baseline <baseline> which could be v2, v3, v3m.
"-mfpu-freg=FREG"
Specify a FPU configuration.
"0 8 SP / 4 DP registers"
"1 16 SP / 8 DP registers"
"2 32 SP / 16 DP registers"
"3 32 SP / 32 DP registers"
"-mabi=abi"
Specify a abi version <abi> could be v1, v2, v2fp, v2fpp.
"-m[no-]mac"
Enable/Disable Multiply instructions support.
"-m[no-]div"
Enable/Disable Divide instructions support.
"-m[no-]16bit-ext"
Enable/Disable 16-bit extension
"-m[no-]dx-regs"
Enable/Disable d0/d1 registers
"-m[no-]perf-ext"
Enable/Disable Performance extension
"-m[no-]perf2-ext"
Enable/Disable Performance extension 2
"-m[no-]string-ext"
Enable/Disable String extension
"-m[no-]reduced-regs"
Enable/Disable Reduced Register configuration (GPR16) option
"-m[no-]audio-isa-ext"
Enable/Disable AUDIO ISA extension
"-m[no-]fpu-sp-ext"
Enable/Disable FPU SP extension
"-m[no-]fpu-dp-ext"
Enable/Disable FPU DP extension
"-m[no-]fpu-fma"
Enable/Disable FPU fused-multiply-add instructions
"-mall-ext"
Turn on all extensions and instructions support
The following options are available when as is configured for a PowerPC processor.
-a32
Generate ELF32 or XCOFF32.
-a64
Generate ELF64 or XCOFF64.
-K PIC
Set EF_PPC_RELOCATABLE_LIB in ELF flags.
-mpwrx | -mpwr2
Generate code for POWER/2 (RIOS2).
-mpwr
Generate code for POWER (RIOS1)
-m601
Generate code for PowerPC 601.
-mppc, -mppc32, -m603, -m604
Generate code for PowerPC 603/604.
-m403, -m405
Generate code for PowerPC 403/405.
-m440
Generate code for PowerPC 440. BookE and some 405 instructions.
-m464
Generate code for PowerPC 464.
-m476
Generate code for PowerPC 476.
-m7400, -m7410, -m7450, -m7455
Generate code for PowerPC 7400/7410/7450/7455.
-m750cl
Generate code for PowerPC 750CL.
-m821, -m850, -m860
Generate code for PowerPC 821/850/860.
-mppc64, -m620
Generate code for PowerPC 620/625/630.
-me500, -me500x2
Generate code for Motorola e500 core complex.
-me500mc
Generate code for Freescale e500mc core complex.
-me500mc64
Generate code for Freescale e500mc64 core complex.
-me5500
Generate code for Freescale e5500 core complex.
-me6500
Generate code for Freescale e6500 core complex.
-mspe
Generate code for Motorola SPE instructions.
-mtitan
Generate code for AppliedMicro Titan core complex.
-mppc64bridge
Generate code for PowerPC 64, including bridge insns.
-mbooke
Generate code for 32-bit BookE.
-ma2
Generate code for A2 architecture.
-me300
Generate code for PowerPC e300 family.
-maltivec
Generate code for processors with AltiVec instructions.
-mvle
Generate code for Freescale PowerPC VLE instructions.
-mvsx
Generate code for processors with Vector-Scalar (VSX) instructions.
-mhtm
Generate code for processors with Hardware Transactional Memory instructions.
-mpower4, -mpwr4
Generate code for Power4 architecture.
-mpower5, -mpwr5, -mpwr5x
Generate code for Power5 architecture.
-mpower6, -mpwr6
Generate code for Power6 architecture.
-mpower7, -mpwr7
Generate code for Power7 architecture.
-mpower8, -mpwr8
Generate code for Power8 architecture.
-mpower9, -mpwr9
Generate code for Power9 architecture.
-mcell
-mcell
Generate code for Cell Broadband Engine architecture.
-mcom
Generate code Power/PowerPC common instructions.
-many
Generate code for any architecture (PWR/PWRX/PPC).
-mregnames
Allow symbolic names for registers.
-mno-regnames
Do not allow symbolic names for registers.
-mrelocatable
Support for GCC's -mrelocatable option.
-mrelocatable-lib
Support for GCC's -mrelocatable-lib option.
-memb
Set PPC_EMB bit in ELF flags.
-mlittle, -mlittle-endian, -le
Generate code for a little endian machine.
-mbig, -mbig-endian, -be
Generate code for a big endian machine.
-msolaris
Generate code for Solaris.
-mno-solaris
Do not generate code for Solaris.
-nops=count
If an alignment directive inserts more than count nops, put a branch at the beginning to skip
execution of the nops.
See the info pages for documentation of the RX-specific options.
The following options are available when as is configured for the s390 processor family.
-m31
-m64
Select the word size, either 31/32 bits or 64 bits.
-mesa
-mzarch
Select the architecture mode, either the Enterprise System Architecture (esa) or the z/Architecture
mode (zarch).
-march=processor
Specify which s390 processor variant is the target, g6, g6, z900, z990, z9-109, z9-ec, z10, z196,
zEC12, or z13.
-mregnames
-mno-regnames
Allow or disallow symbolic names for registers.
-mwarn-areg-zero
Warn whenever the operand for a base or index register has been specified but evaluates to zero.
The following options are available when as is configured for a TMS320C6000 processor.
-march=arch
Enable (only) instructions from architecture arch. By default, all instructions are permitted.
The following values of arch are accepted: "c62x", "c64x", "c64x+", "c67x", "c67x+", "c674x".
-mdsbt
-mno-dsbt
The -mdsbt option causes the assembler to generate the "Tag_ABI_DSBT" attribute with a value of 1,
indicating that the code is using DSBT addressing. The -mno-dsbt option, the default, causes the tag
to have a value of 0, indicating that the code does not use DSBT addressing. The linker will emit a
warning if objects of different type (DSBT and non-DSBT) are linked together.
-mpid=no
-mpid=near
-mpid=far
The -mpid= option causes the assembler to generate the "Tag_ABI_PID" attribute with a value
indicating the form of data addressing used by the code. -mpid=no, the default, indicates position-
dependent data addressing, -mpid=near indicates position-independent addressing with GOT accesses
using near DP addressing, and -mpid=far indicates position-independent addressing with GOT accesses
using far DP addressing. The linker will emit a warning if objects built with different settings of
this option are linked together.
-mpic
-mno-pic
The -mpic option causes the assembler to generate the "Tag_ABI_PIC" attribute with a value of 1,
indicating that the code is using position-independent code addressing, The "-mno-pic" option, the
default, causes the tag to have a value of 0, indicating position-dependent code addressing. The
linker will emit a warning if objects of different type (position-dependent and position-independent)
are linked together.
-mbig-endian
-mlittle-endian
Generate code for the specified endianness. The default is little-endian.
The following options are available when as is configured for a TILE-Gx processor.
-m32 | -m64
Select the word size, either 32 bits or 64 bits.
-EB | -EL
Select the endianness, either big-endian (-EB) or little-endian (-EL).
The following option is available when as is configured for a Visium processor.
-mtune=arch
This option specifies the target architecture. If an attempt is made to assemble an instruction that
will not execute on the target architecture, the assembler will issue an error message.
The following names are recognized: "mcm24" "mcm" "gr5" "gr6"
The following options are available when as is configured for an Xtensa processor.
--text-section-literals | --no-text-section-literals
Control the treatment of literal pools. The default is --no-text-section-literals, which places
literals in separate sections in the output file. This allows the literal pool to be placed in a
data RAM/ROM. With --text-section-literals, the literals are interspersed in the text section in
order to keep them as close as possible to their references. This may be necessary for large
assembly files, where the literals would otherwise be out of range of the "L32R" instructions in the
text section. Literals are grouped into pools following ".literal_position" directives or preceding
"ENTRY" instructions. These options only affect literals referenced via PC-relative "L32R"
instructions; literals for absolute mode "L32R" instructions are handled separately.
--auto-litpools | --no-auto-litpools
Control the treatment of literal pools. The default is --no-auto-litpools, which in the absence of
--text-section-literals places literals in separate sections in the output file. This allows the
literal pool to be placed in a data RAM/ROM. With --auto-litpools, the literals are interspersed in
the text section in order to keep them as close as possible to their references, explicit
".literal_position" directives are not required. This may be necessary for very large functions,
where single literal pool at the beginning of the function may not be reachable by "L32R"
instructions at the end. These options only affect literals referenced via PC-relative "L32R"
instructions; literals for absolute mode "L32R" instructions are handled separately. When used
together with --text-section-literals, --auto-litpools takes precedence.
--absolute-literals | --no-absolute-literals
Indicate to the assembler whether "L32R" instructions use absolute or PC-relative addressing. If the
processor includes the absolute addressing option, the default is to use absolute "L32R" relocations.
Otherwise, only the PC-relative "L32R" relocations can be used.
--target-align | --no-target-align
Enable or disable automatic alignment to reduce branch penalties at some expense in code size.
This optimization is enabled by default. Note that the assembler will always align instructions like
"LOOP" that have fixed alignment requirements.
--longcalls | --no-longcalls
Enable or disable transformation of call instructions to allow calls across a greater range of
addresses. This option should be used when call targets can potentially be out of range. It may
degrade both code size and performance, but the linker can generally optimize away the unnecessary
overhead when a call ends up within range. The default is --no-longcalls.
--transform | --no-transform
Enable or disable all assembler transformations of Xtensa instructions, including both relaxation and
optimization. The default is --transform; --no-transform should only be used in the rare cases when
the instructions must be exactly as specified in the assembly source. Using --no-transform causes
out of range instruction operands to be errors.
--rename-section oldname=newname
Rename the oldname section to newname. This option can be used multiple times to rename multiple
sections.
--trampolines | --no-trampolines
Enable or disable transformation of jump instructions to allow jumps across a greater range of
addresses. This option should be used when jump targets can potentially be out of range. In the
absence of such jumps this option does not affect code size or performance. The default is
--trampolines.
The following options are available when as is configured for a Z80 family processor.
-z80
Assemble for Z80 processor.
-r800
Assemble for R800 processor.
-ignore-undocumented-instructions
-Wnud
Assemble undocumented Z80 instructions that also work on R800 without warning.
-ignore-unportable-instructions
-Wnup
Assemble all undocumented Z80 instructions without warning.
-warn-undocumented-instructions
-Wud
Issue a warning for undocumented Z80 instructions that also work on R800.
-warn-unportable-instructions
-Wup
Issue a warning for undocumented Z80 instructions that do not work on R800.
-forbid-undocumented-instructions
-Fud
Treat all undocumented instructions as errors.
-forbid-unportable-instructions
-Fup
Treat undocumented Z80 instructions that do not work on R800 as errors.
SEE ALSO
gcc(1), ld(1), and the Info entries for binutils and ld.
COPYRIGHT
Copyright (c) 1991-2015 Free Software Foundation, Inc.
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free
Documentation License, Version 1.3 or any later version published by the Free Software Foundation; with
no Invariant Sections, with no Front-Cover Texts, and with no Back-Cover Texts. A copy of the license is
included in the section entitled "GNU Free Documentation License".
binutils-2.26 2016-02-17 AS(1)