Ubuntu Manpage: rotctl - control antenna rotators

Provided by: libhamlib-utils_1.2.15.3-3.1build1_amd64

NAME

       rotctl - control antenna rotators

SYNOPSIS

       rotctl [OPTION]... [COMMAND]...

DESCRIPTION

       Control  antenna  rotators.  rotctl accepts commands from the command line as well as in interactive mode
       if none are provided on the command line.

       Keep in mind that Hamlib is BETA level software. While a lot  of  backend  libraries  lack  complete  rig
       support,  the  basic functions are usually well supported.  The API may change without publicized notice,
       while an advancement of the minor version (e.g. 1.1.x to 1.2.x) indicates such a change.

       Please report bugs and provide feedback at the e-mail  address  given  in  the  REPORTING  BUGS  section.
       Patches and code enhancements are also welcome.

OPTIONS

This program follows the usual GNU command line syntax, with long options starting with two dashes (`-').

Here is s summary of the supported options:

-m, --model=id
Select rotator model number. See model list (use 'rotctl -l').

NB: rotctl (or third party software) will use rig model 1901 when using rpc.rotd or rig model 2
for NET rotctl (rotctld).

-r, --rot-file=device
Use device as the file name of the port the rotator is connected. Often a serial port, but could
be a USB to serial adapter or USB port device. Typically /dev/ttyS0, /dev/ttyS1, /dev/ttyUSB0,
etc. on Linux or COM1, COM2, etc. on Win32.

Also used to specify the host and port to connect to a listening rotctld daemon on POSIX:

-r localhost:4533

and on Win32:

-r 127.0.0.1:4533

-s, --serial-speed=baud
Set serial speed to baud rate. Uses maximum serial speed from rotator backend capabilities as
default.

-t, --send-cmd-term=char
Change the termination char for text protocol when using the send_cmd command. The default value
is <CR>. Non ASCII printable characters can be specified as an ASCII number, in hexadecimal
format, prepended with 0x. You may pass an empty string for no termination char. The string -1
tells rotctl to switch to binary protocol. See the send_cmd command for further explanation.

-L, --show-conf
List all config parameters for the rotor defined with -m above.

-C, --set-conf=parm=val[,parm=val]*
Set config parameter. e.g. --set_conf=stop_bits=2

Use -L option for a list.

-u, --dump-caps
Dump capabilities for the rotor defined with -m above and exit.

-l, --list
List all model numbers defined in Hamlib and exit. As of 1.2.15.1 the list is sorted by model
number.

N.B. In Linux the list can be scrolled back using Shift-PageUp/ Shift-PageDown, or using the
scrollbars of a virtual terminal in X or the cmd window in Windows. The output can be piped to
'more' or 'less', e.g. 'rotctl -l | more'.

-v, --verbose
Set verbose mode, cumulative (see DIAGNOSTICS below).

-h, --help
Show summary of these options and exit.

-V, --version
Show version of rotctl and exit.

N.B. Some options may not be implemented by a given backend and will return an error. This is most
likely to occur with the --set-conf and --show-conf options.

Please note that the backend for the rotator to be controlled, or the rotator itself may not support some
commands. In that case, the operation will fail with a Hamlib error code.

COMMANDS

Commands can be entered either as a single char, or as a long command name. Basically, the commands do
not take a dash in front of them, as the options do. They may be typed in when in interactive mode or
provided as argument(s) in command line interface mode.

Since most of the Hamlib operations have a set and a get method, an upper case letter will be used for
set method whereas the corresponding lower case letter refers to the get method. Each operation also has
a long name; in interactive mode, prepend a backslash to enter a long command name.

Example: Use "\get_info" to see the rotor's info.

Please note that the backend for the rotator to be controlled, or the rotator itself may not support some
commands. In that case, the operation will fail with a Hamlib error message.

A summary of commands is included below (In the case of "set" commands the quoted string is replaced by
the value in the description. In the case of "get" commands the quoted string is the key name of the
value returned.):

Q|q, exit rotctl
Exit rotctl in interactive mode.

When rotctl is controlling the rotor directly, will close the rotor backend and port. When rotctl
is connected to rotctld (rotor model 2), the TCP/IP connection to rotctld is closed and rotctld
remains running, available for another TCP/IP network connection.

P, set_pos 'Azimuth' 'Elevation'
Set position: Azimuth and Elevation as double precision floating point values.

p, get_pos
Get position: 'Azimuth' and 'Elevation' as double precision floating point values.

M, move 'Direction' 'Speed'
Move the rotator in a specific direction at the given rate.

Values are integers where Direction is defined as 2 = Up, 4 = Down, 8 = Left, and 16 = Right.
Speed is an integer between 1 and 100. Not all backends that implement the move command use the
Speed value. At this time only the gs232a utilizes the Speed parameter.

S, stop
Stop the rotator.

K, park
Park the antenna.

C, set_conf 'Token' 'Value'
Set a configuration parameter. It is safe to give "Token" a value of '0' (zero). "Value" may be
a string up to 20 characters.
See -L output

R, reset 'Reset'
Reset the rotator.

Integer value of '1' for Reset All.

_, get_info
Get misc information on the rotator.

At the moment returns 'Model Name'.

w, send_cmd 'Cmd'
Send raw command string to the rotator.
<CR> (or send-cmd-term, see -t option) is appended automatically at the end of the command for
text protocols. For binary protocols, enter values as \0xAA\0xBB

Locator Commands

These commands offer conversions of Degrees Minutes Seconds to other formats, Maidenhead square locator
conversions and distance and azimuth conversions.

L, lonlat2loc 'Longitude' 'Latitude' 'Loc Len [2-12]'
Returns the Maidenhead locator for the given 'Longitude' and 'Latitude'.

Both are floating point values. The precision of the returned square is controlled by 'Loc Len'
which should be an even numbered integer value between 2 and 12.

For example, "+L -170.000000 -85.000000 12\n" returns "Locator: AA55AA00AA00\n".

l, loc2lonlat 'Locator'
Returns 'Longitude' and 'Latitude' in decimal degrees at the approximate center of the requested
grid square (despite the use of double precision variables internally, some rounding error
occurs). West longitude is expressed as a negative value. South latitude is expressed as a
negative value. Locator can be from 2 to 12 characters in length.

For example, "+l AA55AA00AA00\n" returns "Longitude: -169.999983\nLatitude: -84.999991\n".

D, dms2dec 'Degrees' 'Minutes' 'Seconds' 'S/W'
Returns 'Dec Degrees', a signed floating point value.

Degrees and Minutes are integer values and Seconds is a floating point value. S/W is a flag with
'1' indicating South latitude or West longitude and '0' North or East (the flag is needed as
computers don't recognize a signed zero even though only the Degrees value only is typically
signed in DMS notation).

d, dec2dms 'Dec Degrees'
Returns 'Degrees' 'Minutes' 'Seconds' 'S/W'.

Values are as in dms2dec above.

E, dmmm2dec 'Degrees' 'Dec Minutes' 'S/W'
Returns 'Dec Degrees', a signed floating point value.

Degrees is an integer value and Minutes is a floating point value. S/W is a flag with '1'
indicating South latitude or West longitude and '0' North or East (the flag is needed as computers
don't recognize a signed zero even though only the Degrees value only is typically signed in DMS
notation).

e, dec2dmmm 'Dec Deg'
Returns 'Degrees' 'Minutes' 'S/W'.

Values are as in dmmm2dec above.

B, qrb 'Lon 1' 'Lat 1' 'Lon 2' 'Lat 2'
Returns 'Distance' 'Azimuth' where Distance is in km and Azimuth is in degrees.

All Lon/Lat values are signed floating point numbers.

A, a_sp2a_lp 'Short Path Deg'
Returns 'Long Path Deg' or -RIG_EINVAL upon input error..

Both are floating point values within the range 0.00 to 360.00.

a, d_sp2d_lp 'Short Path km'
Returns 'Long Path km'.

Both are floating point values.

EXAMPLES

       Start rotctl for RotorEZ using the first serial port on Linux:

       $ rotctl -m 401 -r /dev/ttyS0

       Start rotctl for RotorEZ using COM2 on Win32:

       C:\> rotctl -m 401 -r COM2

       Start rotctl using rpc.rotd and querying the position:

       $ rotctl -m 101 -r localhost \get_pos

       Connect  to  a running rotctld with rotor model 2 ("NET rotctl") on the local host and specifying the TCP
       port on POSIX:

       $ rotctl -m 2 -r localhost:4533

       and on Win32:

       C:\> rotctl -m 2 -r 127.0.0.1:4533

DIAGNOSTICS

       The -v, --version option allows different levels of diagnostics to be output to stderr and correspond  to
       -v for BUG, -vv for ERR, -vvv for WARN, -vvvv for VERBOSE, or -vvvvv for TRACE.

       A  given  verbose  level is useful for providing needed debugging information to the email address below.
       For example, TRACE output shows all of the values sent to and received  from  the  radio  which  is  very
       useful for radio backend library development and may be requested by the developers.

EXIT STATUS

       rotctl exits with:
       0 if all operations completed normally;
       1 if there was an invalid command line option or argument;
       2 if an error was returned by Hamlib.

BUGS

       This suspiciously empty section...

REPORTING BUGS

       Report bugs to <hamlib-developer@lists.sourceforge.net>.

       We are already aware of the bug in the previous section :-)

AUTHOR

       Written by Stephane Fillod, Nate Bargmann, and the Hamlib Group

       <http://www.hamlib.org>.

COPYRIGHT

       Copyright © 2000-2010 Stephane Fillod
       Copyright © 2011-2012 Nate Bargmann
       Copyright © 2000-2010 the Hamlib Group

       This  is  free  software;  see  the  source  for  copying conditions.  There is NO warranty; not even for
       MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.