Ubuntu Manpage: sockd.conf - SOCKS server configuration file

Provided by: socks4-server_4.3.beta2-19build1_amd64

NAME

       sockd.conf - SOCKS server configuration file

SYNOPSIS

       /etc/sockd.conf

DESCRIPTION

The file /etc/sockd.conf is used to control access to SOCKS proxy server sockd and its services. (See
sockd(8).) Permission and denial of a service request can be decided based on various combinations of
the requesting host, the destination host, the type of service (destination port number), as well as the
requesting user. A line in /etc/sockd.conf can be up to 1023 characters long. Each line may contain the
following fields in the indicated order:

action [?=use_identd] [*=userlist] src_addr src_mask [dst_addr dst_mask] [op dst_port] [ : shell_cmd ]

Spaces and tabs separate the fields. Fields enclosed in square brackets are optional. Blank lines are
allowed. Except for lines that start with #NO_IDENTD: or #BAD_ID:, everything from the first appearance
of # to the end of the line is considered comment and thus ignored by sockd during normal validation.

The action field must be either permit or deny and indicates the action to be taken if a request matches
the conditions specified in that line.

The use_identd field, when present, must be I, i, or n, and is used to specify whether identd
verification should be employed for the current line. ?=I demands the use of identd for verifying the
user's identity, denying access if connection to client's identd fails or if the result does not match
the user-id reported by the client program. ?=i also specifies the use of identd, but denies access only
if client's identd reports a user-id different from what the client program claims. ?=n turns off the use
of identd. For the line in which these fields are used, they override the global identd setting, which is
determined by options -I and -i on the sockd command line.

The userlist field, when present, consists of one or more user-ids or filenames, with comma as separator.
No spaces or tabs are allowed in the list. The user-ids should be ids of users on the requesting host,
not those on the destination host or the SOCKS server host. The filenames must be full pathnames with
the leading /. Inside the specified files, user-ids may be listed one or several per line, with any
combination of blanks, tabs, and commas as separators. The appearance of # marks the remainder of the
line as comment. Each line in the files may be up to 1023 characters long. If the *=userlist field is
omitted, the line applies to all user-ids.

The src_addr and dst_addr fields either specify IP addresses of hosts, networks, or subnets in the usual
dotted form, e.g., 129.201.4.0, or a domain name, e.g., internic.net. The src_mask and dst_mask fields
are masks for the corresponding IP addresses. Bits in these masks that are set to 0 indicate the bit
positions to be ignored during comparisons of IP addresses. So, specifying 255.255.255.255 in the mask
demands an exact match with the specified IP address field, whereas 0.0.0.0 in the mask causes a match no
matter what IP address is specified. The contents of the mask fields are ignore, though they must still
be supplied (use 0.0.0.0), if domain names are used for the corresponding address fields. If the domain
name starts with a period, it specifies a zone and matches all domain names within that zone, otherwise
it matches only the domain name itself. For example, xyz.com matches only xyz.com, while .xyz.com matches
not only xyz.com, but also abc.xyz.com and this.and.that.xyz.com, among others. The special symbol ALL
(which must be entirely in uppercase) matches everything. Domain names are otherwise case-insensitive.

If the dst_addr dst_mask pair is omitted, the line applies to all destination hosts.

The op field must be eq, neq, lt, gt, le, or ge, for the condition of equal, not equal, less than,
greater than, less than or equal, and greater than or equal, respectively. The dst_port field can be
either a port number, e.g., 23, or the equivalent service name as specified in the file /etc/services,
e.g., telnet for port number 23. If this pair is omitted, the line applies to all services, i.e., all
destination port numbers.

For example, consider the line

permit *=root,clivep 128.103.4.10 255.255.255.255 179.200.20.0 255.255.255.0 le 1023

To match the conditions indicated in this line, a request must come from a user named 'root' or 'clivep'
on the host whose IP address is 128.103.4.10 exactly, the destination host must have 179.200.20 in the
first three bytes of its IP address (the last byte doesn't matter), and the service must use a port
number less than or equal to 1023 on the destination host. Since the action field is permit, such
requests will be granted.

When a request is received by sockd, it checks against the lines in file /etc/sockd.conf, one line at a
time. Once it finds a line with conditions that are matched by the request, the request is either granted
or denied based on the action field of that line. The remaining lines of file /etc/sockd.conf are
skipped. If no matching line is found in the entire file, the request is denied.

Be very careful how you order the lines in file /etc/sockd.conf. The following two lines in the
indicated order

deny *=abxyz 128.140.13.24 0.0.0.0
permit 128.140.13.24 0.0.0.0

disallow all requests by user 'abxyz' from host 128.140.13.24, but allow all requests by other users from
the same host. Switch the order of the two lines and even requests by user 'abxyz' are granted.

The shell_cmd field specifies a command string that is executed when the conditions on that line are
satisfied. The following substitutions occur before the string is presented to the Borne shell for
execution:

%A -- replaced by the client host's domainname if known, by its IP address otherwise
%a -- replaced by the client host's IP address
%c -- replaced by "connect" or "bind", the command sockd is asked to execute
%p -- replaced by the process id of sockd
%S -- replaced by the service name (e.g., ftp) if known, by the destination port number otherwise
%s -- replaced by the destination port number
%U -- replaced by the user-id reported by identd
%u -- replaced by the user-id reported by the client program
%Z -- replaced by the destination host's domainname if known, by its IP address otherwise
%z -- replaced by the destination host's IP address
%% -- replaced by a single %

Several shell commands can be strung together in the usual way. For example,

/usr/ucb/finger @%A | /usr/ucb/mail -s 'SOCKS: rejected %u@%A to %Z (%S)' root root@%A

will finger the client host and pipe the result into an email message for superusers at the server host
and the client host with an appropriate Subject line. Most often this feature is used with a deny line,
but it can be used with permit also.

Although there is an implied 'deny all' at the end of the configuration file, you may supply one
explicitly so as to take some specific action when requests are so rejected, e.g., (in one continuous
line),

deny 0.0.0.0 0.0.0.0 : /usr/ucb/finger @%A |
/usr/ucb/mail -s 'SOCKS: rejected %u@%A to %Z (%S)' root root@%A

You may also specify in /etc/sockd.conf commands to be executed when sockd cannot connect to client's
identd or when the user-ids reported by the client programs and the client's identd do not match. These
special entries must have #NO_IDENTD: and #BAD_ID: at the very beginning of the line, followed by the
shell commands to be executed. For example:

#NO_IDENTD: /usr/ucb/mail -s 'Please run identd on host %A' root@%A
#BAD_ID: finger @%A | /usr/ucb/mail -s '%U pretends to be %u on %A' root root@%A

Strictly speaking, sockd has no concept of inside/outside, it does know which is the requesting host and
which the destination and that is the basis of its access control. Therefore it can be used to facilitate
access from outside world into your internal networks as well. Needless to say, you have to take extreme
caution if you choose to do so. If you don't need that kind of access, it is recommended that you
specifically deny such connections in sockd.conf. For example, if the Class B IP network 129.1 is your
internal network, use

deny 0.0.0.0 0.0.0.0 129.1.0.0 255.255.0.0

as the first line of your sockd.conf to protect your inside hosts from all attempts of access from the
outside world through SOCKS. If your internal network consists of several IP networks, you have to use
one such line for each of them. In that case, it may be more convenient to use domain name instead, for
instance,

deny 0.0.0.0 0.0.0.0 .myowm.com 0.0.0.0

deny ALL 0.0.0.0 .myown.com 0.0.0.0

may be used, assuming that myown.com is your domain.

Though the use of domain names can be very convenient and can also reduce start-up overhead by reducing
the number of lines in the configuration file, you should be very careful with your DNS (Domain Name
System) setup. Here are some details that you should know.

The original information the SOCKS server has of the source or the destination host is in the form of its
IP address. The SOCKS server does a reverse DNS lookup to find the domain name correspodning to that IP
address. It then does a normal DNS loopkup to translate the domain name back to an IP address. If the
two IP addresses match, the SOCKS server retains both the domain name and the IP address as identifier of
the host, and will use whichever as appropriate when it checkes the configuration file. If either of the
two DNS lookups fails or if the two IP addresses do not match, SOCKS server retains only the original IP
address as the only identifier of the host, with the consequence that it will not match any line in the
configuration file which specifies a domain name (other than ALL) in the corresponding address field.

Suppose now you add a new host to your internal network before updating your nameserver's data with both
the A record and the PTR record of the new host. When the SOCKS server receives a request with the IP
address of the new host as its destination, at least one of the DNS lookups will fail. Consequently it
will not be protected by lines in which the domain name is used in the destination address field.

So, if you want to use domain name in the configuration file, be very sure that you always keep your DNS
information up-to-date. It's probably a good idea to update your DNS data before adding a new host to
your network. Also make sure that your SOCKS server always queries a nameserver which has the most up-to-
date information of your internal network.

You have the option of using the frozen configuration file /etc/sockd.fc instead of /etc/sockd.conf. The
frozen file is produced by make_sockdfc and is essentially the memeory image of the parsed configuration
file. Using it can reduce the start-up delay of the SOCKS server since it eliminates the need for
parsing.

When the SOCKS server starts, it always looks for the frozen configuration first and reverts to the
unfrozen version only if no frozen configuration is found. All modifications to the configuration must be
done on the plain-text, unfrozen file. Be sure that you run make_sockdfc every time after you modify
/etc/sockd.conf or your SOCKS server would be using the frozen version of an older configuration.

NAME

SYNOPSIS

DESCRIPTION

SEE ALSO